|
| 1 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 3 | Returning filling in including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick for soft/disintegrated rock. |
| 4 | Removing excavated material to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed. |
| 5 | M&L for PCC (1:4:8) type D-2 (using 40mm graded crushed stone agregate) as in foundation, filling and mass concrete complete all as specified and directed. |
| 6 | M&L for PCC (1:3:6) type C-2 (using 40mm graded crushed stone agregate) as in foundation, filling and mass concrete complete all as specified and directed. |
| 7 | Use and waste of flat Form work (Rough finished) to sides of concrete foundations, rafts, plinth beams and similar work, vertical or batter complete all as specified and as directed. |
| 8 | Use and waste of Square, rectangular or polygonal Form work (Rough finished) to sides of pillars, posts, struts, columns and stanchions complete all as specified and as directed. |
| 9 | Use and waste of flat Form work (Fair finished) to surfaces of concrete sides and soffits of floor or roof beam, beam hunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed. |
| 10 | Use and waste of Fair finished flat Form work to soffits of suspended slabs chajjas, floor slabs and similar work not exceeding 200 mm thick (Horizontal or sloping) complete all as specified and as directed. |
| 11 | S&F mild steel TMT reinforcement bars 6 mm to 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 12 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 13 | M&L for Reinforced Cement Concrete (Nominal Mix) Type A-1 (1:1.5:3) (using 20 mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. |
| 14 | M&L for Reinforced Cement Concrete (Nominal Mix) Type A-1 (1:1.5:3) (using 20 mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and as directed. |
| 15 | M&L for RCC (1:1.5:3) Type A-1 (Nominal mix) (using 20mm graded granite stone aggregates) as in Beams, lintels and etc, complete all as specified and as directed. |
| 16 | M&L for RCC Type A-1 (1:1.5:3) (Nominal mix) (using 20mm graded granite stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. |
| 17 | M&L for RCC Type A-1 (1:1.5:3) (Nominal mix)(using 20mm graded granite stone aggregates) as in chajjas and in shelves and the like complete all as specified and as directed. |
| 18 | M&L For RCC M25 (Design Mix) 20mm graded stone aggregate as in Beams, Column, cantilevers, bressummers, lintels over 1.5m span, lintel bands etc complete all as specified and directed |
| 19 | M&L For RCC M25 (Design Mix) 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed |
| 20 | M&L for brick work with old size sub class \"B\" bricks in cement mortar (1:6), straight or curved on plan exc 6m mean radius complete all as specified and directed. |
| 21 | M&L for brick work with old size sub class‘B’ bricks in cementmortar (1:4), straight or curved on plan exc 6m mean radius built complete all as specified and directed |
| 22 | M&L for brick work with old size sub class ‘B’ bricks in half brick thick wallsin cement mortar (1:4), straight or curved on plan exc 6 m mean radius complete all as specified and directed. |
| 23 | M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work of concrete surfaces of walls, finished even and smooth (without using extracement) complete all as specified and directed. |
| 24 | M&L for rendering 15mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. |
| 25 | M&L for rendering 15mm thick in cement mortar (1:3) mixed with water proofing liquid on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. |
| 26 | M&L for rendering 5mm thick on fair faces of concrete of celling in cement mortar (1:3), finished even and smooth (without using extra cement) complete all as specified and directed. |
| 27 | M&L for preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty over one coat of OBD primer complete all as specified and directed. |
| 28 | M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed. |
| 29 | M&L for preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed. |
| 30 | M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 31 | M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 32 | M&L 100mm Cement concrete type D-2, (1:4:8) (40mm graded aggregate) as in sub floor complete all as specified and directed. |
| 33 | M&L 75mm thick Cement concrete type D-2, (1:4:8) (40mm graded aggregate) as in sub base/levelling course etc complete all as specified and directed |
| 34 | M&L 75mm thick plain cement concrete type C-2, (1:3:6) (40mm graded aggregate) as in sub base complete all as specified and directed. |
| 35 | M&L 25mm cement concrete type B-0, (1:2:4) (12.5mm graded aggregate) as in sub floor complete all as specified and directed. |
| 36 | M&L for Non-skid ceramic joint free colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 37 | M&L for ceramic joint free colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surfaces as in skirting/ dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl 10 mm thick rendering in CM 1:4 complete all as specified and directed |
| 38 | M&L for joint free non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular), area of each tile exc 0.06 sqm but n.exc 0.11 sqm, including 15mm thick screed bed or bedding layer in cement mortar (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 39 | M&L Glazed coloured ceramic tiles on vertical surfaces as in skirting/dado 350x 250x7mm/450x300x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick CM in 1:4 complete all as specified and directed. |
| 40 | S&F pressed steel frames for doors with one or more rebates including necessary fitting lugs, lock strike plates etc completed size of frame 165x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B-0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed. |
| 41 | M&L 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats complete all as specified and directed. |
| 42 | S&F Factory made gauged shutter made out of angle iron 35mmx35mmx5mm main frame and 25mmx25mmx5mm and 3mm thick shutter frame and 10mm Square bars at 150mm centre to centre grill complete with stainless steel fly proof wire meshhaving 0.63mm nominal dia wire and 1.4mm average with aperture, with locking arrangement, 100mm MS butt hinges, suitable MS tower bolt and aldrop bolt including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 43 | M&L for preparation of newly steel and iron surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed. |
| 44 | M&L for preparation of newly surface of wood and wood based surfaces by knotting, stopping etc of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 45 | M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed. |
| 46 | S&F factory made solid PVC door shutter30mm thick style consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top and lock rail and bottom rail on either side and as gap insert for top rail & bottom rail: Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specifications complete all as specified and as directed. |
| 47 | M&L 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed |
| 48 | S&F 150mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed. |
| 49 | S&F 100mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed. |
| 50 | S&F 125mm long Aluminium handles, cast type, anodised complete all as specified & directed. |
| 51 | S&F extruded aluminium alloy handles, 150mm long size, fabricated type, anodised complete all as specified and directed. |
| 52 | S&F 140mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 53 | S&F 100mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified & directed. |
| 54 | S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, 100mm long tower bolts, complete with glazing bars, dovetailed or welded complete all as specified & directed. |
| 55 | S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, 100mm long tower bolts, complete without glazing bars, dovetailed or welded complete all as specified & directed. |
| 56 | S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed |
| 57 | M&L Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed |
| 58 | S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. |
| 59 | S&F of 3 mm thick plain, ordinary quality sheet glass and glazing with oil putty or fixed with wooden beads in square not exc 0.5 sqm in each pane complete all as specified and directed. |
| 60 | M&L 4.8 mm Sheet glass, one side frosted quality and glazing without oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed |
| 61 | M&L for framed work such as grills, gratings, hand rails etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed |
| 62 | M&L for Factory made built in steel cup board with pressed steel frame of size 75mm x 45mm x 1.25mm thick with pressed steel shutter 1mm thick Godrej pattern fixed to masonry wall by hold fast made out of 25mmx3 mm flat iron including MS hanging rod of 10 mm dia with bracket fixed on inner side of one leaf of shutter and on other leaf provision of MS peg set of 3 pegs including spray paintingwith two coats of synthetic enamel paint over one coat of red oxide primer and locking arrangement and fixing in position and making good disturbed portion in CM 1:3 or PCC 1:2:4 type B-1 as required complete all as specified and as directed. |
| 63 | S&F vitreous chinaware white wash hand basin (WHB) size 550mm x 400mm, Ist quality,including provision of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls & making good & including providing and fixing of suitable 32mm bore heavy duty waste pipe and CP waste fitting (waste coupling) complete all as specified and directed. |
| 64 | S&F Vitreous China urinals incl spreader, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed. |
| 65 | S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed |
| 66 | S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including jet spray & Seat Cover complete all as specified and directed. |
| 67 | S&F 10 ltrs PVC valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed |
| 68 | S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed |
| 69 | S&F 450 mm long PVC connection with brass nuts on both ends for 15mm bore pipes complete all as specified and directed. |
| 70 | S&F 15mm bore CP fancy type Bib taps, castcopper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed |
| 71 | S&F 15mm bore fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed |
| 72 | S&F 15mm bore CP fancy type angle cock/ Stop valves with long/ short shank, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed |
| 73 | S&F for Stop valves, fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed suitable for 15mm bore pipe complete all as specified and directed. |
| 74 | S&F 125mm Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed |
| 75 | M&L for Looking Mirror 600x450 mm size selected quality 5mm thick with 20mm wide aluminium angle frame all around and 6 mm thick AC building board or commercial plywood backing and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 76 | S&F factory made looking mirror of size 750x1200mm bevelled edge 5.50mm thick of selected qualitiy glass mounted on udaipur green marble on wall with chromium plated brass screws and cup washer complete all as specified and directed. |
| 77 | S&F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed |
| 78 | S&F CP brass or stainless steelgrating 100/125mm dia/size square or round fixed complete all as specified and directed. |
| 79 | S&F Bras CP Tubular Towel Rail 20mm dia, 600mm longfixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) complete all as specified and directed |
| 80 | S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed. |
| 81 | S&F 20mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed. |
| 82 | Ditto all as above but of size 25mm bore |
| 83 | Cutting chases in brick wall, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10 cm girth complete all as specified and directed. |
| 84 | S&F Rotational moulded polyethylene water storage tank ISI marked of 1000 ltr capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position as specified in SSR Part-I including all fittings complete all as specified and as directed. |
| 85 | S&F Rotational moulded polyethylene water storage tank ISI marked of 500 ltr capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position as specified in SSR Part-I including all fittings complete all as specified and as directed. |
| 86 | S&F Gun-metal globe or gate valves 20mm bore cast copprer alloy with iron wheel head, screwed both ends for ironcomplete all as specified and directed. |
| 87 | S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms) complete all as specified and directed. |
| 88 | S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed |
| 89 | S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed |
| 90 | S&F 110MM PVC (SWR) vent cowl complete all as specified and directed |
| 91 | S&F PVC (SWR) 75 mm floor/Nahani trap with grating including jointing to waste pipe in cement concrete complete all as specified and directed. |
| 92 | S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed |
| 93 | S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed |
| 94 | S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed |
| 95 | S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed |
| 96 | S&F 75mm bore CI floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 97 | S&F CI sand cast pipes 100mm bore in floors, fixed or laid in trenches complete all as specified and as directed |
| 98 | S&F CI sand cast pipes 100 mm bore, fixed to walls complete all as specified and as directed |
| 99 | S&F CI sand cast pipes 75mm bore in floors, fixed or laid in trenches complete all as specified and as directed |
| 100 | S&F CI vent cowl for 100mm bore CI pipes with complete all as specified and as directed. |
| 101 | S&F Cast Iron Bends any radius 100mm bore with oval assessed door fixed in any position fixed complete all as specified and as directed. |
| 102 | S&F Cast Iron Single Branch Piece (T junction) 100mm bore with oval assessed door fixed in any position fixed complete all as specified and as directed. |
| 103 | M&L for 75mm thick cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in flooring, path, plinth protection and the like, laid in alternate bays n.exc 2.50 Sqm and joints filled with mastic filling including finishing even and smooth without using extra cement complete all as specified and directed. |
| 104 | S&F 25mm dia stainless steel fancy type curtain rod in suitable size with and including mild steel fancy type brackets, stops of matching colour and necessary curtain rings, side caps etc complete all as specified and directed. |
| 105 | M&L rolled MS Joist, channel, angle, or tee sections, fixed independently, without connecting plates etc (cut to ordinary lengths i.e within 20mm of the length indicated complete all as specified and directed (Fe-410-W (Gde E-250) quality B) |
| 106 | M&L for carrying out water proofing treatment for roofs in the following stages :-(i)Rendering 10 mm thick plaster/screed in cement mortar (1:4) mixing with water proofing compound (as per manufacturer instructions) and surfaces finished even and smooth without using extra cement all as specified. Note :(i) WPC shell be measured separately and paid for under respective item of schedule.(ii) First coat of bitumen primer conforming to IS-3384 @ 0.40 Kg/Sqm over plastered surfaces.(iii) Second coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm.(iv) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric with aluminum based reflective paint.(v)Final coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg per Sqm. |
| 107 | M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with gray cement and pigment, complete all as specified and directed. |
| 108 | M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with gray cement andno pigment, complete all as specified and directed. |
| 109 | M&L for PCC (1:3:6) type C-2 (using40 mm graded crushed stone aggregrate) as in bed to 150mm internal dia SGSW drain pipes including packing under and haunching against sides of pipes after they are laid and tested complete all as specified and directed. |
| 110 | M&L for SGSW drain pipe of 150 mm internal dia, grade `A\", laid in trenches and jointed in cement mortar (1:1) complete all as specified and directed. |
| 111 | Supply only WPC complete all as specified and directed. |
| 112 | M&L for cement concrete (1:2:4) type B-2 using 40mm graded stone aggregate in surface channels and drains. |
| 113 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. |
| 114 | Add or deduct for each 25 mm girth or part there of over or under 30cm ditto |
| 115 | Drilling/cutting and tapping cast iron water mains or GI water mains and suitable size of straight plain brass ferrules/GI Tee (in position) for branch connection of 20mm bore pipe complete and specified as directed. |
| 116 | M&L for Soakage wells excavation, in any type of soil, foundation in PCC (1:3:6), walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.2 M dia X 3 M effective depth complete all as specified in Drg No TD/309 sheet No 1/4 to 4/4. |
| 117 | M&L for point wiring with1.5 sq mm PVC insulated, unsheathed, stranded copper conductor (FRLS-H) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit/ casing caping and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface &making gooddisturbed surface, provision of GI/Pressed steel terminal switch box with plastic laminatedsheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) as earth wire connected with main common earth dolly complete all as specified and directed for the following :- |
| 118 | One light/fan/bell/exhaust fan point controlled by one, one-way Piano type switch 5/6 Amp complete all specified and directed. |
| 119 | One 3pin/5pin 5/6 Amps socket out let on same board controlled by one, one-way Piano type switch complete all specified and directed. |
| 120 | One 3pin/5pin 5/6 Amps socket out let onindependent board controlled by one, one-way Piano type switch complete all specified and directed. |
| 121 | All as per item No 117 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor1100 V grade PVC insulated FRLS-Hbut unsheathed single core for16 Amps power point on independent board and 2.5 sqmm FRLS-H cable as earthwire complete all specified and directed. |
| 122 | S&F switch piano flush type whitefinish 5/6Amps, single pole one way, 230 volts, 50 hz complete all as specified & directed. |
| 123 | S &F socket out let2 pin 5/6 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed. |
| 124 | S&F switch piano flush type whitefinish 15/16 Amps single pole one way, 230 volts, 50 hzall as specified and directed |
| 125 | S&F socket out let5 pin 15/16 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed. |
| 126 | S&F fan regulator, flush stepped type ,electronic, compatible with BLDC fan completeall as specified and directed. |
| 127 | M&L ceiling rose 3 terminal / PVC/ polycarbonate, isolated body all as specified and directed |
| 128 | S&F lamp holder (Angular/Straight), insulated body, with back plate for batten fitting complete all as specified & directed. |
| 129 | S&F LED Bulb 9 Watt (cool day light) having colour suitable for \"B-22 type to fix on batten holder complete all as specified and directed. |
| 130 | S&F LED tube light batten 20 watts 4 fts extruded aluminium housing, translucent diffuser with LED light source, 2000 lumen, natural white ,surge protection range-2KV, voltage protection range 120-280 VAC with intergrated driver and surge protection complete all as specified and directed. |
| 131 | S&F Decorative ultra slim round profile LED Tube light fitiing with extruded polycarbonate, energy efficient for mirror light 9/10 Watt 2 ft with LED light source with uniform light output, fixed on site with all accessories all as specified & directed. |
| 132 | S&F LED 25/30 watt Building security light fitting mounting type made out of one piece in pressure die-cast aluminium housing with high efficient LED as lighting source and PC Cover separate compartment for electronic driver, including bracket clamp of suitable size with nuts, bolts and washers etc. and connected with existing ceiling rose complete with electronic driver and all accessories. The fitting shall IP 66 protection, duly prewired complete all as specified and directed. |
| 133 | S&F sheet metal enclosure double door type for MCBs DB SPN (Single pole and neutral) 240V AC 4 way with suitable rated busbar, minimum ingress protection of IP40 all as specified and directed. |
| 134 | S&F sheet metal enclosure double door type for MCBs DB SPN (Single pole and neutral) 240V AC 8 way with suitable rated copper busbar all as specified and directed. |
| 135 | S&F sheet metal enclosures with metal socket and plug top Single pole and neutral enclosure with a two pin and earth plug and socket complete ISI marked, 230/240 volts, 50 hzwith one single pole MCBSP 20 Amps all as specified and directed. |
| 136 | S&F MCCB/MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in suitable copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface complete all as specified and directed. |
| 137 | S&F MCCB 100A, 15/16 KA, 4 Pole, 415 V, 50 Hz with fixed thermal magnetic release fixed in Vertical TPN complete all as specified and directed. |
| 138 | S&F MCB, SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, \"B\" series and making connections with suitable size of copper lugs complete all as specified & directed.Note : MCBs should bo of same Make as of DB |
| 139 | S&F MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, \"B\" series and making connections with suitable size of copper lugs complete all as specified & directed.Note : MCBs should bo of same Make as of VTPN & DB |
| 140 | S&F sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 6.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLS-H) as earth wire and wire connected withmain earth dolly including cutting chasing and making good disturbed portionall as specified and directed |
| 141 | All as per item No 137 here-in-before-but of size 4.00 sqmm |
| 142 | S&F weather proof PVC insulated and PVC sheathed twin core aluminium cable of size 6 sqmm complete all as specified and directed. |
| 143 | S&F ventilating/PVC exhaust fans fancy square type 225 mm sweep with plastic fiber body heavy duty 230 Volt AC, single phase complete with plastic louvers and including making suitable size of holes in wall for fixing the fan & making good including making electrical connection with ceiling rose including taking down existing unserviceable ventilating fan of any description complete all as specified and directed. |
| 144 | S&F Exhaust fan PVC body AC single phase 230/240 Volt of size 250 mm sweep 900 RPM complete with louvers shutter including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed . |
| 145 | S&F Ceiling fan complete with three blades down rod, accessories 230 V, 1200mm sweep with minimum air delivery of 210 CFM(BLDC) complete all as specified and directed . |
| 146 | S&F electric water heater, storage type steel body with copper inner tank and heating element upto 1.5/2 KW capacity 25 litre, BEE 5 Star rated, ISI Marked, 240 V, 50 Hzcomplete with all accessories such as safety valve, thermostate, NRV, Hot and cold water connection pipe all as specified and directed. |
| 147 | S&F Desert cooler electric driven (single phase), having nominal air flow capacity of minimum 4000 CFM plastic body, densenest honeycomb cooling pads, copper wounded motor speed having 1350 RPM with blades, submersible water lifting pump suitable to lift water upto 6 feet including Speed regulator, electrical cord three core and plug top 5 Amp complete all as specified and directed. |
| 148 | Supply, Installed & fix maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2mm with copper bonding thickness of 250 micron,UL listed,CPRI Tested at 25 KA fault current for one second and is provided with universal clamp made of SS earth enhancing compound shall be of 50kg/pit (resistivity is less than 0.12 Ohm meter) tested as per IEC 62561-7. The above arrangements shall be provided with heavy duty earth poly plastic pit cover of 6000 kg load bearing capacity (Size:270x240x200mm) andFRLS insulated copper conductor of size 6 sqmm, single core cable drawn through and including light grade GI pipe of size 15 mm upto 7 mtr incl cutting and chases on wall and floor and making good using PCC complete all as specified and directed. |
| 149 | Supplying & laying LT UG cable ( Conforming to IS 1554) ISI marked 1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor in trenches/ ducts/ through GI pipe under roads of size 10 sqmm 4 core complete all as specifed and directed. Note;- The earth work shall be measured and paid sepretely under appropriate item of Sch A |
| 150 | Supply and laying clean dry river sand for cushioning in layers, 8 cm before lying of cable and 15 cm after lying of cable (total 23 cm) in trenches complete all as specified and directed. Note:- Thickness of sand cushioning shall be measured as 18 cm after punning for payment) |
| 151 | Supply and laying old size sub class ‘B’ bricks for cable protection, laid dry flat adjacent to each other across the length of cable complete all as specified and directed. |
| 152 | S&F 32mm dia bore GI tubing, light grade with all fittings for cable protection including GI clamps, nut & bolts and washers or burried in ground complete all as specified and directed. |
