|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:4:8 (1 cement : 4 fine aggregate : 8 graded stone aggregate 40mm nominal size) |
| 2 | Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 fine aggregate) |
| 3 | Brick work with common burnt clay F.P.S (non modular) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 fine aggregate) |
| 4 | Providing and fixing to existing door frames - 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm x 25 mm or less as per requirement with an average wall thickness of 1 mm (+- 0.3mm ). PVC foam end cap of size 23 x 10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. An M.S.tube havingdimensions 19 mm x 19 mm and 1.0 mm (+- 0.1mm ) is inserted along the hinge side of the door. Core of the door Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end -cap of the size 25 mm x 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer\"s specification to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places. |
| 5 | Providing and fixing factory made P.V.C. door frame of size 50x 47 mm with a wall thickness of 5mm , made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 nos , of 150mm long brackets of 15 x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19 x19 mm M.S.square tube of 19 gauge , EPDM rubber gasket weather seal to be provided through out the frame . The door frame to be fixed to the wall using M.S.screws of 65 / 100 mm size, complete as per manufacturter\"s specification. |
| 6 | Cement concrete flooring 1:2:4 (1 cement : 2 fine aggregate : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate |
| 7 | 12mm cement plaster of mix -1:4 ( 1 cement : 4 fine aggregate) |
| 8 | 15mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1cement : 4 fine aggregate) |
| 9 | 20mm cement plaster of mix -1:4 (1 cement : 4 fine aggregate) |
| 10 | Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 11 | Distempering with Ist quality acrylic distemper ready mixed, having VOC (Volatile Organic Compound) content less than 50 grams /litre, of approved brand and manufacutre, including applying additional coats wherever required, to achive even shade and colour -Old work (one or more coats) |
| 12 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams / litre, of approved brand and manufacturer, including applying additional coats wherever required, to achive even shade and colour - One coat |
| 13 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams / litre , of approved brand and manufacturer, including applying additional coats wherever required, to achive even shade and colour - Two coats |
| 14 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc., complete |
| 15 | Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade- Old work (one or more coats) |
| 16 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq.metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground as per direction of Engineer-in-charge - with cement mortar 1:4 (1 cement : 4fine aggregate) |
| 17 | Providing & fixing white vitreous china water closet squatting pan (Indian type) along with \"S\" or \"P\" trap including dismantling of old WC seat and \"S\" or \"P\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba , all complete as per the direction of Engineer-in-charge- Orissa pattern W.C.Pan of size 580x440 mm |
| 18 | Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level white P.V.C. flusing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required - W.C. pan with ISI marked white solid plastic seat and lid. |
| 19 | Extra for using coloured WC pan instead of white WC pan Orissa pattern WC pan 580 x 440 mm. |
| 20 | Extra for using coloured pedestal type WC pan (European type) with low level cistern of same colour instead of white vitreous china WC pan and cistern. |
| 21 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings - flat back wash basin of size 550x400mm. |
| 22 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing fixed to wooden cleats with C.P.brass screws and washers complete - rectangular shape 600x450mm |
| 23 | Providing and fixing C.P.brass bib cock of approved quality conforming to IS: 8931 - 15 mm nominal bore. |
| 24 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms - 15mm nominal bore. |
| 25 | Applying of multi surface Nano-scaling system with organosilane based reactive water proofing agent (Zycosil + or =) Nano sealer duly mixed with (acrylic based sealing bonding admixture Zyco prime or equivelent) mixed in the proportion as recommended by the manufacturers with potable water (< 1000ppm) on the prepared surface of masondry / concrete. The rate to include the cost of preparing the surface by chipping. cleaning the bulged/loose concrete/ mortat removing smooth by sand paper/stone and fanning/blowing the dust by air compressor, preparing the solution in manufacture\"s recommended proportion and applying on the surface directed by the Engineer-in-charge. |
