|
| 1 | Site clearance: Surface dressing of ground including removing vegetations and / or inequalities not exceeding 15 cms deep and disposal of rubbish upto lead of 50 m and lift upto 1.5 m for all kind of soil, complete as per specifications and as directed by Engineer-in-Charge. |
| 2 | Earthwork in excavation in all types of ground substrata consisting of hard rock / fragmented rock / soft rock / ordinary soils / filled up ground / murrum requiring use of rock breaker, drilling, chiseling with mechanical / manual means etc.up to a depth of 1.5 m from the original ground level and dewatering if required for foundation of walls, columns, platforms etc. including backfilling with selected excavated materials in plinth and foundation trenches in layers not exceeding 200 mm thick, watering ramming etc. complete and disposing off the surplus materials to a maximum radially measured lead of 1.0 KM. as per drawings, design , safety and specifications and directions of the Engineer.Note :- Bidders should essentially visit and inspect the construction sites and determine themselves the right and safest method/s of excavation considering the safety of nearby structures and population, before quoting their item rates (Blasting is not permitted). |
| 3 | Up to 1.50 m depth from the average existing ground level. |
| 4 | Extra over item No.2.1 for every additional lift of 1.5m part thereof in ordinary rock/ hard rock. |
| 5 | BACKFILLING: Backfilling at all levels for road works, sides of foundations, trenches, and other low lying area with following excavated materials including cost of breaking/ crushing the same to required size, consolidation in layers, all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 6 | From stockpiles of excavated rock/ soil within a lead of 1500 m. |
| 7 | Extra over item no. 4.1 above for every additional lead of 500 m or part thereof. |
| 8 | GOOD EARTH: Supplying at site of good quality earth /morrum/ gravel excavated and brought from outside plant (borrow pits/ stock piles), free from weeds, roots, pebbles, rubble, boulders more than 150mm in size and other foreign material, including royalty & carriage, and filling earth (excluding rocks) in trenches, plinth, and sides of foundation, etc., in layers not exceeding 200 mm in depth, consolidating each deposited layer by ramming & watering, for lift up to 1.5 m, etc., all complete with safety and as per drawings, specifications and as directed by Engineer-in-charge.Note: Only consolidated fill volume shall be measured and paid. |
| 9 | Providing and laying in position cement concrete of 1:3:6(1 Cement: 3 coarse Sand : 6 Graded Stone aggregate 20 mm nominal size) -at all level , transporting of concrete to site, laying, consolidation, finishing, curing etc. all complete excluding cost of centering & shuttering, as per direction of Engineer-in-charge. |
| 10 | Plain cement concrete (PCC) :Providing and laying cement concrete of 1:2:4 ( 1 Cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size) in retaining walls, return walls, walls(any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed block, anchor block, window sills, fillets etc. at all level including transporting of concrete to site, laying including cost of finishing, curing etc. all complete excluding the cost of centering and shuttering as per specifications and direction of Engineer-in-charge. |
| 11 | Reinforced cement concrete (RCC): Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M-25 to M35 grades for Reinforced cement concrete work and Plain cement concrete works using 20mm size stone aggregates including transporting of concrete to site for laying but excluding the cost of centering, shuttering and reinforcement, including cost of finishing, compaction, curing, approved chemical admixtures in recommended proportions for achieving slump not less than 120mm and water/cement ratio not more than 0.45 at all level as per direction of Engineer-in-charge. Use of concrete retarding agent / accelerator conforming to IS 9103 shall also be done if situation demands so. Rates should be based on using 350 kg of cement per cum of concrete. Note: Adjustment of cement used in addition to or less than as mentioned above shall be paid/ recovered at Rs 4.85/ kg. |
| 12 | Form Work : Providing form work of battened frame with sheathing having plywood lining / MS angle frame with sheathing of MS plate lining so as to give fair finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor not exceeding 3.5 meters to ceilings and removal of same for foundation, footings, columns, wall, Suspended floors, stairs, landings, balconies, lintels, beams, plinth beams, girders, cantilevers and access platform, roads etc. complete at all level of floors / roof as per specifications and direction of Engineer in charge. |
| 13 | Extra for additional height in centering, shuttering wherever required with adequate bracing, propping etc. including cost of de-shuttering and de-centering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part there of (Plan area to be measured). |
| 14 | Providing and laying Thermo-Mechanically Treated reinforcement bars of grade Fe-500D or more or as specified in drawings/specifications and as directed by engineer conforming to IS : 1786 latest revision or the latest relevant code for RCC work including straightening, cutting, bending, placing in position and binding with 20 gauge annealed binding wire and cement mortar cover block of all size in C.M. 1:2 mix etc. all complete at all levels- as per drawings , specifications & direction of engineer in charge.Notes: 1. Chairs, Spacers, supports and approved laps which are embedded in the concrete shall be measured and paid in this item.2. Reinforcement steel used for formwork and its supports shall not be paid. |
| 15 | Providing & laying Random Rubble masonry with hard stone in foundation and plinth level of building & upto 3.00 Mtr. height from NGL for boundary/compound wall with Cement mortar 1:6 (1 Cement :6 Coarse sand) including cost of labour, materials, curing , raking out the joints , finishing, scaffoldings etc. all complete as per specifications and direction of Engineer in charge. |
| 16 | BRICK MASONRY: Providing and laying Fly-ash brick masonry using Fly-ash building bricks of class designation- 75 ( IS-12894 -latest revision ) in cement mortar 1:6 ( 1 cement : 6 coarse sand) in superstructure above plinth level up to floor five level as per specifications and direction of Engineer including cost of labour, materials, curing, finishing, scaffoldings etc. all complete as per drawings, specifications and direction of Engineer-in-charge. |
| 17 | POINTING ON MASONRY: Pointing on stone work with cement mortar 1:3 (1 cement :3 fine sand): Raised and cut pointing including finishing, curing, scaffoldings etc. complete at all height as per drawings, specifications and direction of Engineer-in-charge. |
| 18 | External Plastering : Providing and laying 18 mm thick cement plaster in two coats under layer 12 mm thick cement plaster 1:4(1 cement : 4 fine sand) finished with a top layer 6mm thick cement plaster 1:4 (1 cement : 4 fine sand) on either side of single or half brick masonry walls for exterior plastering at all height and using galvanized M.S. wire of I.S. gauge designation 26 S.W.G. chicken mesh over junctions of brick work, beams and column as required including necessary grooves at the junction of RCC and brick work, arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm in girth including scaffolding, finishing, curing etc. all complete as per specifications and direction of engineer. |
| 19 | Internal Plastering: Providing and laying 15mm thick cement plaster 1:4 (1 cement : 4 fine sand) in single coat on either side of single or half brick wall for interior plastering at all levels using galvanized M.S. wire of I.S. gauge designation 26 s.w.g. chicken mesh over junctions of brick work, beams and column as required including necessary grooves at the junction of RCC and brick work, arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm in girth including scaffolding, finishing, curing etc. all completeas per specifications and direction of engineer. |
| 20 | Ceiling Plastering : Providing and laying 6mm thick cement plaster (1 cement : 3 sand) in single coat on RCC ceiling face for interior plastering at all levels including necessary grooves at the junction of RCC and brickwork arises, internal rounded angle, chamfers and / or rounded angles not exceeding 80 mm in girth including scaffoldings, finishing, curing etc. all complete as per specifications and direction of engineer. |
| 21 | External Painting :Supplying and applying weather proof exterior emulsion paint of make Asian paint apex (code 0012) / Nerolac excel / Weather coat smooth of Berger as approved of required shade on New work Two coatsincluding base coat of exterior wall primer of make Asian exterior wall primer (0065) / Nerolac exterior primer / Weather coat exterior primer of Berger as approved after cleaning / scrubbing of the surfaces with wire brushes, soft brushes, sand papers, steel sheet scrappers and mechanical grinder etc. for removing all kind of burrs, imperfections, undulations and other such defects existing in the surface including filling surface imperfections such as holes, dents, cracks by using mixture of white cement & fine sand (in the ratio of 1:3) to achieve plain & even surface. The item rate include spreading of suitable clean protection covering on all exposed surfaces to protect them from staining. All surfaces surrounding to painted area such aswindow / ventilator frames, glass pans etc. shall be cleaned to sparkling clean condition using suitable thinners, detergents, chemical cleaners etc. under the scope of the item.including the cost of materials, labour etc. all complete as per specification & direction of Engineer-in-Charge. Note:- Painting to be taken up after attending all seepage / leakage problem. No peel off of paint & seepage spots shall be allowed. |
| 22 | Internal Painting :Supply and applying premium emulsion paint of make Asian paint premium emulsion (product code 011) / Nerolac Beauty gold / Rangoli fashion finish of Berger as approved to give an even shade: - Two coats on new work including priming coat with approved cement primer of make Asian Deco prime wall primer (0360) / Nerolac water thinnable cement primer / BP cement primer water thinnable of Berger as approved and applying of 1 mm thk white cement based putty for smoothining of wall surface, after cleaning / scrubbing of the surfaces with wire brushes, soft brushes, sand papers, steel sheet scrappers and mechanical grinder etc. for removing all kind of burrs, imperfections, undulations and other such defects existing in the surface to achieve plain & even surface. The item rate include spreading of suitable clean protection covering on all exposed surfaces to protect them from staining. All surfaces surrounding to painted area such as door & window frames, glass pans, electrical fittings, switch board, floors, skirting, platform etc. shall be cleaned to sparkling clean condition using suitable thinners, detergents, chemical cleaners etc. under the scope of the item.including the cost of materials, labour etc. all complete as per specification & direction of Engineer-in-Charge. Note:- Painting to be takenup after attending all seepage / leakage problem. No peel off of paint & seepage spots shall be allowed. |
| 23 | Supplying and application of 2 coats of Synthetic Enamel Paint (Asian Utsav Enamel Paint: Product Code No 0053 or similar quality in Berger / Nerolac) on New / Old Concrete / Plastered / Steel / Wooden surfaces after application of primer coat (Asian Paint Metal Primer: Product Code 0005 or similar quality in Berger / Nerolac) on the surfaces well prepared through scrapping, scrubbing, grinding and cleaning using wire brushes, soft brushes & sand papers etc. including cost of materials, labour, consumables cleaning of area after painting etc. complete as per direction of Engineer-in-Charge. The item rate includes the cost ofspreading suitable clean protection covering on all exposed surfaces to protect them from staining, cleaning of old stained / freshly stained surfaces surrounding to painted area such as door - windowframes & glass panes, electrical fittings, switch boards, floors, skirting, platform etc. to sparkling clean condition with the use of suitable thinners, detergents, chemical cleaners etc. |
| 24 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade in two or more coats on new works. |
| 25 | Providing and laying vitrified floor tiles in different sizes of min. thickness 9mm with water absorption less than 0.08% Band conforming to IS: 15622, of approved make, in all colours and shades, laidon 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete. |
| 26 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 27 | Providing and laying in position minimum 8mm thick 1st premium quality Anti skid ceramic tiles of approved size and colour to be used in wet areas for flooring and all as per specification. |
| 28 | Providing and laying Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade includingincluding edge molding and cutting three nos. grooves neatly in longitudinal direction of steps for antiskid purpose, rubbing and polishing complete, including cutting of slot (without edge splitting) using mechanical means for receiving the handrail supports including rubbing, curing and polishing, finishing & curing work at all level etc. complete (size of stone shall cover full length & width of stair case treads as shown in drawings) as per specification & direction of Engineer-in-charge. |
| 29 | Providing and fixing polished Kota stone slab flooring 18 to 22 mm thick in flooring, tread of steps, landing, laid over 20 mm (average) thick base of cement mortar 1:4 (1 Cement: 4 sand): and jointed with white cement slurry mixed with pigment to match the shade of the slab, including edge molding and cutting three nos. grooves neatly in longitudinal direction of steps for antiskid purpose, rubbing and polishing complete, including cutting of slot (without edge splitting) using mechanical means for receiving the handrail supports including finishing & curing work at all level etc. complete (size of kota stone shall cover full length & width of stair case treads as shown in drawings) as per specification & direction of Engineer-in-charge. |
| 30 | Structural Steel Work : Supplying, fabricating and erecting in position M.S. steel structural work for grills, plate/ sleeve embedded parts, railing, gates, edge angles, grating, door frames etc. consisting of M.S. Angles, MS Tee, MS flats, joists, square bars, plates, MS tubes,MS bars, Wire mesh, channel, bolts etc. including cost of nut & bolts of required dia cutting, making holes, welding with existing G.I. / M.S. steel structure etc. , painting with one coat of red oxide primer and two coats of synthetic paint in cluding all labour, materials, tools-tacles, scaffolding, etc. all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 31 | Providing and fixing stainless steel ( Grade 304) railing, post, truss, frame etc. made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 32 | Providing and fixing 1mm thick M.S. sheet sliding – shutters with frame and diagonal braces of 40x40x6mm angle 3mm M.S. gusset plates at the junction and corners 25mm dia pulley, 40x40x6mm angle and T- iron guide at the top and bottom respectively including applying a priming coat of approved steel primer all complete- as per drawings, specifications & direction of engineer in charge. |
| 33 | Providing and fixing colour anodized aluminium work for doors, windows, ventilators and partitions as per thematerial,fabrication and dimensional specifications/ requirement of IS: 1948 from aluminum alloy extruded sections, tubular / appropriate Z and or other sections of approved make conforming to grade HE9-WP of IS : 733 and HV9-WP of IS: 1285, fixed with raw plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with requiredneoprene felt and silicon whether sealant etc. Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling. C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. : For shutters of doors, windows & ventilators including providing and fixing approved ss hinges/ pivots/ rollers suitable for sliding / openable window and providing and fixing approved fittings i.e. two handle with locking arrangement for each sliding window shutter and one handle as well as two tower bolt for each glass / jali shutter with provisions of one gate hook for each glass shutter for openable window wherever required as approved including the cost of neoprene gasket all complete: colored anodized coated aluminium (thickness of anodized coating 15 micron). The finished arrangement shall be fully water tight. Note : 1. Payment of Glazing / SS wire mesh to be paidin relevant item in line with their specifications.2. Cost of SS hinges / pivot / rollers are to be included in the quoted rate and no payment shall be made for providing and fixing the same. |
| 34 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item). |
| 35 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm). |
| 36 | with toughned glass minimum thickness 12 mm required as per drg and as per direction of Engineer-in-charge. |
| 37 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Rate shall be inclusive of providing and fixing of door handle and locking arragement) |
| 38 | Providing and fixing pressed steel door frames conforming to IS: 4351 manufactured from 1.6 mm thick commercial mild steel sheetincluding hinges jamb, lock jamb, bead and base ties of pressed mild steel angle of size 20mm x 20mm x 1.25mm thick to suit floor thicknesswelded or rigidly fixed together by mechanical means, adjustable lugs with split end tail fixed to each jamb including fixing superior quality heavy duty Stainless Steel Butt Hinges 100mm longwith the frame using SS-MS welding process and SS Screws all as per specifications including provision of mortar guards, lock strike – plate and shock absorbers as specified, filling the hollow box space with the 1:2:4 cement concrete (6.7 mm down coarse aggregate to be used), water cured for minimum 7 Days before fixingthe same and applying two coats of approved brand synthetic enamel paint on exposed surface over a coat of approved steel primer on entire surface (interior and exterior) after pre- treatment of the surface, drilling holes of specified diameter and depth with the provision of high quality rubber/PVC sleeves for accommodating male parts of door fittings such as aldrops and tower bolts etc. all complete including cost of all material and labour as per drawing, specifications andas directed by Engineer–In charge. |
| 39 | Supplying and erecting including assembling, fitting and fixing factory made swing in / swing out 45 mm thick hollow galvanised heavy duty MS pressed steel flush doors (As per IS: 4351) along with frame at all elevations, single/ double leafs, with or without top removable panels, using galvanised MS sheets for frames and leaves, mastic caulking and grouting the frame, reinforcing and insulating with mineral wool or Polyurethane foam as approved by the Engineer including providing 6 mm clear sheet glass vision panel of 200 mm x 300mm in each leaf, heavy duty SS hinges, thresholds, fittings complete with frame, fittings, fixtures and all hardware such as aldrops, tower bolts, handles, buffers, door stopers, necessary rubber gaskets/ seal for achieving air-tightness etc. as a complete package including one coat of approved primer and two coats of best quality approved paint as necessary all complete as per drawings, door schedules ,specifications as directed by engineer. Note: Size of clear opening shall be considered for measurement. |
| 40 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with Second class teak wood including grinding, polishing, applying one coat of approved wood primer to the exposed surfaces and two coals of bituminous paint to the surfaces of frames in contact with masonry/concrete etc. complete as per drawings, specifications and direction of Engineer. |
| 41 | Providing and fixing factory made 35 mm thick both side laminated flush door shutters single / double leaf conforming to IS ; 2202(part-1) of make KITPLY/ GREENLAM / CENTURYas approved by EIC with Block board core & frame of well seasoned hard wood, cross band made from BWP grade veneers andcommercial BWP grade face veneers on both sides of shutter including providing and fixing 2nd class teak wood leaping of suitable size and shape all around the edges including supply and fixing of approved brand stainless steel fixtures like Tower bolt (size-250mm long rod size 12mm), Tadi latch (300mm long rod size 14mm), Aldrop (300X16mm), Handles plate type - 100mm size (size shall be confirming to IS:208) - 02 nos, Magnetic Cather, mortice lock etc. with approved quality etc. complete as per drawings, specifications and direction of Engineer. (Door skin shall be 1.0 mm thick on front face and 0.8mm thick on back face with the provision of edge bending of decorative high pressure laminated sheet of plain/wood grain in gloss/ matt/ suede finish with high density protective surface layer of make KITPLY / GREENLAM / CENTURYas approved by EIC).Note - Actual area of shutter will be paid.Vision panel & louvers as per site requirement. |
| 42 | Providing and fixing 30mm thick factory made pre-laminated PVC door shutter of approved make and design consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make. M.S. frame covered with 5 mm thick heat molded PVC \"C\" channel of size 30 mm thickness, 95 mm width out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 115 mm wide PVC sheet out of which 95 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 140 mm wide PVC sheet out of which 100 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the \"C\" Channel using PVC solvent adhesive etc. including all SS fitting and fixtures suchas 1 nos Tadi latch 200mm longx12mm rod size, 2 nos. tower bolt 250mm x 12mm, 2 nos. plat type handles - 100mm size (size shall be confirming to IS:208) of approved brand complete as per drawing, specification & direction of Engineer-in-charge. |
| 43 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564)wegiht upto 35 kg and necessary accessories and screws etc. complete as directed by Engineer-Incharge |
| 44 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the walls etc. |
| 45 | 15 mm nominal outer dia Pipes |
| 46 | 20 mm nominal outer dia Pipes |
| 47 | 25 mm nominal outer dia Pipes |
| 48 | 32 mm nominal outer dia Pipes |
| 49 | Providing and fixing on wall face / embedded in ground un plasticized Rigid PVC Rain water pipes of Jain Irrigation / Finolex / Supreme as approved conforming to IS:13592 type A (4 Kg/Cm2) including shoes, bends, clamps etc.jointing with seal ring leaving 10 mm for thermal expansion (I) single socketed pipes all complete at all levels as per direction of Engineer-in-Charge : 110 mm dia. |
| 50 | Providing & Fixing of UPVC Pipes (IS : 15328) for Drainage / Severage System of Supreme/ Finlox / Jain Irrigation as approved make including jointing tees, bends, clamps , pipe with solvent cement rubber sing and Lubricant etc.all complete at all levels as per direction of Engineer-in-Charge.(i) 110 mm SN - 8 |
| 51 | GI PIPE: Providing, laying, jointing, fixing and testing MS Galvanised Pipes class \"C\" heavy quality as per IS: 1239 & Fittings confirming to IS: 1879 like tees, elbows, collars, unions, nipples, enlargers, reducers, bends, coupling & all other fittings required to complete the work, including laying under the floors, in walls where required cutting chase through brick or concrete work and making good after erction of the pipe lines, roof slabs, including cost of all jointing materials like Teflon tape, clamps, wooden gutties, screws, cement, sand etc. complete testing the pipes with clean water as per the code of practice water supply in building of IS: 2065, etc., all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 52 | 15mm dia |
| 53 | 20mm dia |
| 54 | 25mm dia |
| 55 | 32mm dia |
| 56 | 50mm dia |
| 57 | WASH BASIN: Providing and fixing best quality wash basin rectangle type of nominal size 550 x 400 mm comprising of:-Best Indian make wash basin in white glazed vitreous china ware conforming to IS: 2556 part-IV supported on suitable CI wall brackets and of size mentioned above HIS or parry ware or CERA make-I grade, approved by Engineer-in-charge.-One number heavy quality 15 mm NB CP brass pillar cock ESSCO or SIEKO or SSF make with jam nut conforming to IS: 1779.-One number 15 mm NB heavy quality PVC inlet connection with brass union, washers at ends.-One number 15 mm NB heavy quality CP brass screw down stop cock conforming to IS: 781 weighing not less than 400 gms.-One number 32 mm NB heavy quality CP brass waste coupling with rubber plug & chain.-One number 32 mm NB CP brass bottle trape with extension piece and wall flange, etc., all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 58 | LIPPED URINAL: Providing & fixing best quality hindware/ parryware/ cera make White vitreous chinaware flat back lipped front urinal of basin of 465 x 355 x 265 mm or equivalent with 5-10 litres capacity automatic flushing PVC cistern with all fittings, fitted on GI brackets, standard size galvanised iron flush pipe, waste pipe and CP brass spreaders with brass union, push cocks, specials, connecters & stopcock, CP brass fittings, etc., and GI clamps, painting of fittings and brackets, cutting chase and making good the walls, etc., all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 59 | EUROPEAN WATER CLOSET: Providing and fixing EUROPEAN WATER CLOSET suit (Hindustan sanitary ware, PPM, CERA OR NYCER brand) comprising of:-Wash down platform European water closet best Indian make in white glazed vitreous with integral \"P\" or \"S\" trap.-15 mm NB heavy quality PVC inlet connection with brass unions connected ends.-15 mm NB screw down heavy quality CP brass stop cock conforming to IS: 781.-Solid plastic heavy quality seat with lid of approved make and colour with CP brass pillar hinges, conforming to IS: 2548 (Part-II).-10 liters capacity plastic low level flushing cistern of gleaming white shade best quality champian or approved equivalent, conforming to IS: 7231 complete with all internal fittings, matching heavy quality PVC flush bend mounted on a pair of white enamel painted brackets, etc., all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 60 | Providing and fixing Orissa pattern Water Closet (OP 23 (Open rim) of H & R Johnson / Orissa C0117 of Parryware/ Orissa COVYS 3010104 of CERA as approved with low level placed PVC flushing cistern (Dual Flush Tank {white} of H & R Jhonson / CERA/ Parry ) connected with 32 mm dia PVC flush pipe with all fittings and brackets with C.P. brass angle cock with CP flange (Clarion cat No. CQT 23059 make of JAQUARor similer approved quality in KOHLER / GROHE and 15 mm dia high quality PVC inlet connection of required length with all accessories, fittings & fixtures of best quality and brand. Item includes essentially following.(a). Orissa pattern white glazed viterous china W.C. pan of size 580mm x 440mm of approved brand and 100mm dia sand cast iron \"P\" trap.(b). Low level placed PVC flushing cisternDual Flush Tank (white) of H & R Johnson ( P2829PW) / Parry (Slim-line E8110 Deluxe) / Cera (Corona B1020102) as approved with all accessories complete.(c). 15mm dia PVC inlet connection of required length of approved brand with heavy duty C.P. brass unions and rubber washer etc.(d). 15mm dia C.P. brass angle valve with C.P. flange of superior quality (Jaquar Clarion cat. No.CQT 23059 or similer approved quality of KOHLER / GROHEas approved). |
| 61 | Providing and fixing C.P. brass wall mixer with 3 in 1 system with provision for both hand shower and over head shower complete with 115mm long bend pipe on upper side, connecting legs and flanges (without hand & over head shower) CQT - 23281UPR of Jaquar Clarion series or similar approved quality of GROHE/KOHLER as approved. |
| 62 | Providing and fixing cut edge mirror 6mm thick of overall size600X450mm especially fabricated with superior glass (of approved quality) with designer acrylic PVC frame of approved colour and make mounted around with 6mm thick non-water absorbent Acrylic/PVC material backing fixed with cleats, all complete as per the specifications and directions of Engineer. |
| 63 | Providing and fixing in position heavy duty gun metal wheel valve screw down type confirming to IS: 778 latest revision of approved make including the cost of all jointing materials, fittings and testing etc. complete as per specifications of the following nominal bore. - |
| 64 | 50 mm nominal bore |
| 65 | 20 mm nominal bore |
| 66 | 25 mm nominal bore |
| 67 | 32 mm nominal bore |
| 68 | Providing and fixing gun metal non- return valve of approved quality (screwed end). : 50 mm nominal bore |
| 69 | BIB COCK: Providing fixing of CP brass long body bib cock of approved make 15 mm dia ,good quality with weight not less than 690 g, etc., all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 70 | STOP COCK: Providing and fixing of approved quality CP brass stop cock 15 mm dia (concealed)of weighing not less than 400 g, etc., all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 71 | GULLY TRAP: Providing & fixing in position best quality salt glazed Stone Ware Gully Trap with 150 mm x 150 mm square inlet & 100 mm N.B. outlet conforming to IS: 651 including embedding the trap in 1:4:8 cement concrete, 150 mm x 150 mm size grating at top, construction of brick masonry chamber 300 mm x 300 mm (internal dimension) in 230 mm thick brick masonry, embedding the trap, plastering with cement mortar 1:4, 20 mm thick inside, outside & all exposed faces, finished with a floating coat of neat cement, providing & fixing CI frame and cover weighing not less than 7 kg, painting the grating, frame & cover with two coats of approved bitumastic paint, etc., all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 72 | CI NAHANI TRAP: Providing & fixing cast iron Nahani trap of self cleaning design conforming to IS: 3989 with 75 mm outlet having a minimum water seal of 50 mm with stainless grating on top including necessary 1:2:4 cemnet concrete for embedding the trap top the waste pipe forming circular hole upto floor level and rendering smooth, etc., all complete as per drawings, specifications and as directed by Engineer-in-charge. |
| 73 | Providing & Fixing of Silicon sealant filling as Directed by the Engineer-in-Charge. |
| 74 | Providing and laying non-pressure NP2 class (light duty) R.C. hume pipesjointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete: 200mm dia. R.C.C. pipe. |
| 75 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. |
| 76 | GI Chainlink fencing : Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm made with 4mm dia GI Wire including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm. |
| 77 | GI Wire :Supplying, fixing and tying in rows of 4mm dia GI wire inposition running through the hooks provided in the G.I. chain link fence in proper line & level& two coats of aluminium paint as per drawing, specifications & direction of engineer. Note : Length of chain link fence shall only be measured. |
| 78 | Supplying & fixing in positing galvanized steel barbed wire(IS:278-1978 type A-5) weighing not less than 9.38 Kg. Per 100 metres, strainingand fixing to any type of standard, rails, straining bolts including securing with and provision of Galvanized mild steel wire, staples or steel pins, two coats of aluminium paintetc. as directed by Engineer. (Posts & struts of concrete, steel, etc. shall be measured and paid in relevant schedule item). |
| 79 | Supply and application of polyurethane based bitumen free single pack elastomeric liquid applied water proofing membrane for a thickness of 1200 microns. The surfaces to be applied should be dry, cleaned and free from oil and grease.Loose particles should be removed and damaged spotsrepairedfirst. Cracksshouldbe filledupcementmortar forming groove as per manufacturer\"s recommendations, Thewholeterrace before and after sofinished shallbe floodedwith waterforminimumperiodof two week for curingand forfinaltest. Allaboveoperations to bedone in order as per the specifications and directions of Engineer-in-charge. |
| 80 | WATER STOPS: Supply and install of 225 mm wide PVC water stops, for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete, inclusive of making all types of joints in water stops by fusing, etc., and testing of joints to establish continuity between segments of the water stop and between water stop and embedded parts by splicing, all complete as per drawings, specifications & as directed by Engineer-in-charge. |
| 81 | Providing and laying 125 micron thick c.c. road grade colorless polyethylene sheet over a prepared road surface for concrete pavement with provision of 150mm wide over lapping on either side of sheet at joints, nailing etc. complete as per specification & direction of engineer incharge. |
| 82 | Providing and fixing in position bitumen hot sealing compound Using grade \"A\" sealing compoundincluding cutting of contraction /Expansion/Construction joints in concrete using mechanical concretecutter including cost of diamond bit cutting wheel etc. For expansion joints of size 25mm X 25mm |
| 83 | Providing and laying Mild steel reinforcement bars (32 mm dia bar rounded type) for expansion joint and Tor steel reinforcemnt bars in longitudnel joints in concrete road work including straightening, cutting, bending, placing the bars in position etc. all complete- as per drawings , specifications & direction of engineer in charge. |
| 84 | Providing and fixing 40mm dia 350mm long best quality PVC Sheathing around the exposed portion of the 32mm dia mild-steel bars at construction joints, wrapping cotton waste with grease etc. all around the bars including pluging the end with PVC cap all complete as per drawing, specification and direction of engineer in charge. |
| 85 | Providing andfixing in position premolded expansion joint filler board of 25mm thickness of universal asphalt or Shalitex STP as approved confirming to IS 1838 (part-I) as per specifications. |
| 86 | Providing and fixing of 25 mm dia GI conduit pipe in RCC STRUCTURAL part. As per requirement in beam slabs and walls for cables crossing and where ever required or as per direction of engineer in charge. |
