|
| 1 | Dismantling brick work tile, masonry or tile lining [CSR Item no.8.5(b)] |
| 2 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. includingmembering and stacking within 50 metres lead.[CSR Item no.8.46] |
| 3 | Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead.[CSR Item no.8.45] |
| 4 | Dismantling concrete cement concrete plain 1:2:4 mix.[CSR Item no.8.6(d)] at lawn tennis court |
| 5 | Dismantling concrete lime concrete,cement concrete of 1:6:12 or leaner mix.[CSR Item no.8.6(a)] at lawn tennis court |
| 6 | Earth work in excavation in foundations trenches etc. in all kinds of soil where Pick-Jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm, layers with compaction including disposal of all surplus soil as directed within lead of 30 metres.(CSR item No.6.6) |
| 7 | Carriage of Earth,Surkhi, Sand, Earth, Fly Ash, Bajri, Ballast, Stone boulders, Kankar and building rubbish, Earth.0.5 to 1.0km including loading and unloading.[CSR item No.5.2(i) & 4.1(A)] |
| 8 | Cement concrete 1:6:12 with stone ballast 40mm gaugemixing by mechanical means using concrete mixer volumetric type[CSR Item No.10.8(a)ii] |
| 9 | Earth filling under floors with surplus soil containing more than 40% gravel or kankar excavated from foundation & taken only from outside the building plinth in 15 cm layers including ramming watering and consolidation lead upto 30 metres[CSR Item No.6.8(ii)] |
| 10 | Cement concrete 1:5:10 with stone ballast 40mm gauge using concrete mixer volumetric type[CSR Item no.10.9(b)ii] |
| 11 | Cement concrete 1:4:8 with stone ballast 40mmgauge using concrete mixer volumetric type[CSR Item No. 10.11](ii) |
| 12 | Cement concrete 1:2:4 with stone ballast or shingle mixing by mechanical means using concrete mixer volumetric type [CSR Item no.10.13a(ii)] A&C-1 |
| 13 | Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but including steel reinforcement centring and shuttering in foundation and plinth.[CSR Item 10.15] A&C-1 |
| 14 | Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.[CSR Item No.10.20] A&C-1 |
| 15 | First class burnt brick laid in cement sand mortar 1:4 in first storey upto 4 meter[CSR Item No.11.8] |
| 16 | Damp proof course 2.5cm thick of cement concrete 1:2:4 with 2 coats of bitumen 20/30 penetration at 1.65 Kg per sqm laid hot and sanded [CSR item No.10.28] |
| 17 | 12.5 mm thick cement plaster 1:5[CSR item no.15.10] |
| 18 | Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)[CSR item no.9.1] |
| 19 | Centering and shuttering for faces of walls, partitions,retaining walls and the like (vertical or battering including attached pilasters buttresses etc.[CSR Item no.9.2] |
| 20 | Centering and shuttering for columns (Square or rectangular or polygonal in plain) [CSR item No.9.4] |
| 21 | Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels[CSR Item no.9.6] |
| 22 | Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg. /Sqm top of R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean afterwire brushing[CSR Item no.13.13(i)] A&C-9 |
| 23 | Plastering on underside of ceiling 10mm thick cement plaster 1:4 [CSR Item No.15.44} |
| 24 | Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-35 grade machine made rubber moulded smooth finish with strong vibratory process or with vibro hydraulic compaction machine and of approved size and design / shape laid in Ordinary Grey and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge for Non traffic Areas and streets having width less than 3.05 mt.( Also not to used over footoaths) [CSR item no.14.137] |
| 25 | Providing and laying vitrified floor tiles in different sizes in light colour shades made using Full Body Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Full body vitrified tiles have pigment in entire body / thickness of tile which makes chips and scratches less noticeable and make na ideal choice for high traffic zones.) 600X600mm [CSR Item no.14.115(a)] |
| 26 | Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading.[CSR Item no.14.72] |
| 27 | Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS :15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x 300 mm as approved by Engineer-in Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement:4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete[CSR Itemno.14.128] |
| 28 | Kapoor Sail wood chowkats including iron hold fasts iron hinges corner straps clears, stops wooden knobs fixed in position.[CSR Item No.17.15(xiv)] Single rebate |
| 29 | Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position (Code IS 2202-1(1999) Decorative with teak facing on both sides edges lipped with teak with laminated core(IV)35mm thick [CSR Item no.17.27c(iv)] A&C-2 |
| 30 | Providing and fixing bright finished brass 100 mm mortise latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality).[CSR Item no. 17.22(iv)] |
| 31 | Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt) [CSR Item no.17.23(i)] |
| 32 | Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish[CSR Item no. 16.65] |
| 33 | Wall painting with plastic emulsion paint of approved brand and manufacture to give even shade(two or more coats)[CSR item no.16.63] |
| 34 | Painting two or more coats with synthetic enamel paints in all shades on old wood work or metallic or plastered or concrete surface to give an even shade including rubbing down old paint.[CSR Item no.16.18] |
| 35 | Finishing walls with Premium Acrylic smooth exterior paint with silicon additives of required shade with two or more coats applied @1.43litre/10sqm over and including base coat of water proofing cement paint applied @2.20kg/10sqm.[CSR Item no.16.61] |
| 36 | Providing and fixing aluminum grill 6.3 mm including cost of necessary fittings i.e. screws With Clip Ruber etc. Complete. [CSR Item no.17.95] |
| 37 | Structural steel work in girders or Stanchions built up of one joist/ or channel section. Riveted including cutting and fixing old gusset plates bolts,Nuts,Rivets etc. complete with flange plates,head, sole plates, angle connections etc. with hoisting & erecting in position.[CSR Item no. 18.6] |
| 38 | Steel work in hip & jack rafters common rafters purlins etc. with angle cleats and other connecting plates.[CSR Item No.18.2] |
| 39 | Providing and fixing PUF panel (PPGL) Core thickness of PUF panel 40mm thick,40 density polyurethane form and two layers of metal sheets precoated painted galvalume sheet roofing/walls (size,shape and pitch of corrugation as approved by Engineer in charge). The sheet shall be fixed using self driling/self tapping screws with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 40 | Applying priming coat with metal primer on new steel or iron work including preparation of surface.[CSR Item no.16.20] |
| 41 | Painting one coat with readymixed paint of metallic surfaces in all shades on old steel or iron works.[CSR Item No.16.22] |
| 42 | Ridges and valleys 45 cm overall, in plain G.I. Sheet 0.80mm fixed with galvanzed iron J. and L. hooks 10mm diameter, G.I. Limpet and bitumen washers complete.[CSR Item no.13.21] |
| 43 | Providing and fixing 110 mm dia . U.P.V.C Rain water pipe of 2.5 kgf./sqm as per IS:4985 including jointing during masonary complete as per specifications and to the entire satisfaction ofEngineer-in- charge.[CSR Item no.13.74] |
| 44 | Providing 3-Seater stainless steel benches with back seat surface having bench size 1300x450mm & back rest size 1300x300mm for badminton court.The bench/chair weighs 25kg.(Quotation attached) |
| 45 | Badminton Net as per specifications. |
| 46 | Badminton Pole setas per specifications. |
| 47 | Wooden Flooring(Maple wood) for badminton court |
| 48 | Lawn Tennis pole set as per specifications. |
| 49 | Lawn Tennis Net as per specifications. |
| 50 | Chain link fencing wire having perimeter of size 120m,Height=3.65m with 50mm mesh size for lawn tennis court. |
| 51 | Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position. [ CSR-item No.18.4] |
| 52 | Providing and Fixing Baskit Ball Polls 6\"\" Dia GI Pipe with projiction 220cm fitted,fiber glass board 180cm x 105cm 20mm thick, both side frame 40mmx40mmx3mm support 1\" pipe & Ring 20mm complete set as per standard specification Baskit ball pole. |
| 53 | Providing and laying cement colour of sorts for demarcation of all lines of basketball ground |
| 54 | Providing and fixing 5 star Split air conditioner 1.5 ton (Make Hitahi,Carrier & O general) (Qo(Quotation Attached) |
| 55 | Providing and fixing Voltage Digital display stablize for Ac Up to 1.5 ton working Range Voltage 130V -300VW(Make Microtek,V-guard,Everest.(Quotaion Attached) |
| 56 | Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition.Size 75x75mm[CSR Item no.30.85](a) |
| 57 | Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) BClass including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete.[CSR Item no.28.35(a) 15mm i/d |
| 58 | Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) BClass including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete.[CSR Item no.28.35(b)20mm i/d |
| 59 | Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) BClass including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete.[CSR Item no.28.35(c)25mm i/d |
| 60 | Providing, fixing and jointing ISI Marked GunMetal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on G.I. Pipe lines laid in the ground or inside buildings including all carriages complete.[CSR Item no.28.43(a)] 15mm i/d Gun Metal peet valve heavy pattern |
| 61 | Providing, fixing and jointing ISI Marked GunMetal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on G.I. Pipe lines laid in the ground or inside buildings including all carriages complete.[CSR Item no.28.43(b)]20mm i/d Gun Metal peet valve heavy pattern |
| 62 | Providing, fixing and jointing G.I Union Couplings(of approved make with the approval EIC) as per IS 1879 in G.I. Pipe lines complete in all respect.15mm i/d G.I. Union [CSR Item no.28.40(a)] |
| 63 | Providing, fixing and jointing G.I Union Couplings(of approved make with the approval EIC) as per IS 1879 in G.I. Pipe lines complete in all respect.20mm i/d G.I. Union [CSR Item no.28.40(b)] |
| 64 | Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing.160mm o/d SWR UPVC pipe lines laid complete [CSR Item no.30.74 B(a) |
| 65 | Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing.110mm o/d SWR UPVC pipe lines laid complete [CSR Item no.30.74 B(b) |
| 66 | Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.P Trap/Floor Trap 110mm x 110mm[CSR Item no.30.81iii B (ix)] |
| 67 | Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.Elbow 90 Degree (All side socketed) [CSR Item no. 30.81 iii B(v) |
| 68 | Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its originalcondition but excluding cost of lead joining.Vent Cowls[CSR Item no. 30.81 iii B (vi)] |
| 69 | Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm. 100mm internal Diametre S.W.gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm[CSR Item no. 30.99(a)] |
| 70 | Providing and fixing in position Chinaware Indian Orisa water closet size 580x440 mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern ISI makred including cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer-in-charge.[CSR Item no.30.2] |
| 71 | Providing and fixing jet spray with 2\"-6\" long PVC pipe.With PTMT nut [CSR Item no.30.8(b)] |
| 72 | Providing and fixing plastic hygenic seat cover with lid complete.Plastic Seat Cover Premium starwhite/pastel/special colour[CSR Item no.30.9(a)] |
| 73 | Providing and fixing C.P. brass Urinal Spreader Ocular-Regular complete with fittings for urinals complete.[CSR Item no.30.23] |
| 74 | Providing & fixing in position vitreous Chinware white Indian make flat back or angular lipped front small urinals size 265x315x440mm approved make (to the approval of the Engineer-in-charge) with C.P. brass tube connection 300 mm long complete in all respect [CSR Item no.30.15 |
| 75 | Providing and fixing partition for different type of urinals.19 to 20 mm thick Granite stone partitionsize 375mm x 750mm[CSR Item no.30.21(A)ii] |
| 76 | Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in allrespect.Size 550 mm x 400 mm x 815 mm[CSR Item no. 30.32 ii] |
| 77 | Providing and fixing vitreous chinaware pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect.Vitreous chinaware standard white pedestal for wash hand basin.[CSR Item no.30.43 (i)] |
| 78 | Providing and fixing P.V.C Waste Pipe Collapsiable 32mm complete in all respect.[CSR Item no.30.20] |
| 79 | Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect.C.P.brass 15mm Angle valve without flange [CSR Item no.30.66(c) |
| 80 | Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge)Size 600mmx450mm[CSR Item no. 30.61(a)] |
| 81 | Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respectPVC tube connection of size 15 mm x300 mm with PTMT nut[CSR Item no. 30.72©] |
| 82 | Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects[CSR Item no.30.80] |
| 83 | Providing & Fixing in postion 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge )complete in all respect. C.P. brass Bib cock foam flow without flange [CSR Item no.30.65A(ii)] |
| 84 | Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screwscomplete in all respect.C.P. brass towel Rails size 15mm dia 610mm long[CSR Item no.30.58(a)] |
| 85 | Providing & fixing in position Water Dispenser Top Loading (with refrigration capacity 15 ltr) of approved make (to the approval of Engineerin- charge ) dispensing hot/cold/ambient water including cost of two no. 20 ltrs packaged drinking water bottles and carriage complete in all respect. [CSR Item no.30.26)] |
| 86 | Providing & fixing in position Commercial RO without reservoir with four no cartridge/membrane having flow rate 50 ltr/hr with 6 stage purification process of approved make (to the approval of Engineer-in-charge ) including carriage and fixing in position complete in all respect.[CSR Item no.30.27] |
| 87 | RECESSED PVC CONDUIT PIPE WIRING SYSTEMWITHMODULARSWITCHES:Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. Combined / universal Socket (shuttered) 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½\" deep for walls and CI 3\" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- (i) (b) ] Wiring fan point (With fan box)[ csr item 34.02 (i) (b)] |
| 88 | Wiring light point.[CSR Item no.34.02 (ii)] |
| 89 | Wiring 6 Amp. wall socket point.[CSR Item no.34.02(iv)] |
| 90 | Wiring 16/20 Amp. power plug control point.[CSR Item no.34.02 (vi)] |
| 91 | PVC INSULATED FR COPPER CONDUCTOR CABLES:Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable up to 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-Overall size 2.5 sq.mm (Un-sheathed).[CSR Item no. 34.09 iii] |
| 92 | Overall size 4 sq.mm (Un-sheathed).[CSR Item no. 34.09 iv] |
| 93 | MINIATURE CIRCUIT BREAKERS/RCBO\"s/ RCCB\"s:Supply and erection of Miniature Circuit Breaker MCB\"s for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:-MCB Single Pole 6-32amp. (10kA, Curve-C).[CSR Item no.34.16 A(ii)] |
| 94 | MCB Four Pole 50, 63amp. (10kA, Curve-C). [CSR Item no.34.16 A (xvi)] |
| 95 | SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB\"s / RCBO\"s / RCCB\"s:Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper bus bars, shrouded neutral bars, earth bars, cement spill protector, colour coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO\"s/ RCCB\"s in the distribution board (For SP&N distribution board with provision DP MCB\"s/ RCCB\"s/ RCBO\"s as incomer and SP MCB\"s as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB\"s/ RCCB\"s/ RCBO\"s as incomer and SP MCB\"s as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:-TP&N Vertical Double Door Distribution Board 4 way each. [CSR Item no.34.17(ix)] |
| 96 | PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:-Heavy Gauge PVC Conduit Pipe 25 mm dia.(Flushed). CSR Item no.34.12(x) |
| 97 | Heavy Gauge PVC Conduit Pipe 50mm dia. (Flushed).CSR Item no.34.12(xiii) |
| 98 | SHEET METAL IRON CLAD SWITCHES: Supply and erection of sheet metal Iron Clad Switches on existing surface with G.I. bolts & nuts/ rag bolts and nuts etc., according to the size of holes in the body of the enclosure including connections with suitable size of thimbles and bonding to the existing earth as Per PWD General Specifications:-ICTPN Switch 100 amp., 415 volts. CSR Item no.34.18(vii) |
| 99 | SUPPLY AND ERECTION OF WIRING ACCESSORIES: Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing Bakelite / modular cover frame including fixing & connections and petty material etc :-Bakelite Batten Holder (Large size).[CSR Item no.34.15 (xxvii)] |
| 100 | Ceiling Rose (Flush Piano type).CSR Item no.34.15 (xxvi) |
| 101 | XLPE INSULATED LT CABLES:XLPE INSULATED ARMOURED CABLES (UNDER GROUND):Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed armoured and served cable 100volts grade as per IS:7098 (Part-1) 1988 to be laid 1 metre below ground level including excavation, sand cushioning, covering with sand & First Class bricks and back filling the trench etc., of the required size as per PWD General Specifications:-Overall size 35 sq.mm (4Core) Armoured (Underground).[CSR Item no.34.10A(xxxix)] |
| 102 | Overall size 16sq.mm (4Core) Armoured (Underground).[CSR Item no.34.10 A(xxxvii)] |
| 103 | 3-STEPPED STEEL TUBULAR POLE:Supply and erection of 3-Stepped steel tubular swaged and welded pole (410-SP-Mpa) of suitable length confirming to IS: 2713-(PART-II)-1980 (Steel tubes confirming to IS:1161-1979, UTS 42kg f/Sq.mm) to fix up to a required planting depth below ground level in a hole of excavation about 45cm dia. and suitable depth to fill up to 15cm below G/L with 1:2:4 cement concrete mixture including painting of pole with two coats of approved aluminium paint as required:-Overall length 9.5metre, with planting depth 1.8 metre, length of sections 5metre, 2.25 metre and 2.25 metre (Bottom, Middle and Top respectively), Outer dia andthickness of sections 165.1mm x 4.85mm,139.7mm x 4.5mm and 114.3mm x 3.65mm (Bottom, Middle and Top respectively) with approximate weight 160kg. (410SP-38) base Plate weight 7.5kg.of size 12mm thick about 30 cm dia. [CSR Item no.34.31 (viii)] |
| 104 | M.S. JUNCTION BOX FOR STREET LIGHT:Supply and erection of M.S. Junction box of suitable size made from M.S. Sheet 16SWG (1.60mmthick). Junction box should have one locking arrangement and 2 nos. Hinges onfront side . It should have 1No. Brass terminal connecting strip, 1No. Kit kat 16Amp /240Volts along with M.S. Flat 20mmx2mm clamp with nuts and bolts for fixing on the pole. The junction box should be painted with one coat of good quality primer and two coats of post officered enamel paint inside and outside complete in all respect:-M.S.JunctionBox205mmx155mmx95mm .[CSR Item no.34.38(ii) (a)] |
| 105 | M.S. JUNCTION BOX FOR STREET LIGHT:Supply and erection of M.S. Junction box of suitable size made from M.S. Sheet 16SWG (1.60mmthick). Junction box should have one locking arrangement and 2 nos. Hinges onfront side . It should have 1No. Brass terminal connecting strip, 1No. Kit kat 16Amp /240Volts along with M.S. Flat 20mmx2mm clamp with nuts and bolts for fixing on the pole. The junction box should be painted with one coat of good quality primer and two coats of post officered enamel paint inside and outside complete in all respect:-M.S.JunctionBox205mmx155+B109mmx95mm .[CSR Item no.34.38(ii) (a)] |
| 106 | OVER HEAD DISTRIBUTION ALUMINIUM CABLES, ACSR CONDUCTORS, CLAMPS, JUMPERS& J OINTKITS:Wiring over- head line in PVC insulated & PVC sheathed two single core aluminium conductor cable overall 1100 volts grade complete in all respect as approved and desired by the Engineer In- Charge at site.PVCinsulated& PVC sheathed aluminium conductor cable Overall Size 4mm² (1/1.40mm)Twin Core. [CSR Item no.34.34(ii)(a)] |
| 107 | Providing and Fixing ceiling LED Flood Light 150 watt (Great White) |
| 108 | Providing and Fixing LED Bulb 15 watt(Havel’s) |
| 109 | Providing and Fixing LED Tube 20 watt(Havel’s) |
| 110 | Providing and Fixing Exhaust Fan(Havel’s) |
| 111 | Providing and Fixing Ceiling Fan 48\"\"(Crompton) |
| 112 | Providing and FixingCeiling Fan pipe (Rod) 1½´ (18\"\") with D clump |
| 113 | Providing and Fixing Garden Light 20 Watt, |
