|
| 1 | M&L for cutting down removing vegitation plant digging out penetrated roots withtronices looping branches not exc. 10cm girth PROTRUDING over wall roofs by necessary cutting hole in brick / concrete wall/ surfaces and injecting chemical GLYPHOSPHATW 41% SL 20 ml or till refusal by makimg cut/ injection in the stem of plant 30mm C/C spraying with solution (25ml Glyphospoto 41% diluted with one litre water) and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 and to match the existing work and finishes and removing of debris out side premises/ defence land including necessary scaffolding etc wk will be carried out upto 6 th storey height bldgs complete all as specified & directed.Note: \"The use / work of GLYPHOSATE FORMULATION TO BE CARRIED OUT / ALLOWED THROUGH PEST CONTROL AUTHORISED OPERATORS\" as approved by GE. |
| 2 | M&L for Cutting chases, pinningin making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills sunshades, shelves lintels etc and cutting chases for concealed water pipe etc and making good cutting not exc 10cm. complete all as specified and directed. |
| 3 | Supply only Liquid water proofing compound ISI Marked (used 200 ml per bag of cement) complete all as specified and directed. |
| 4 | Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 sqm and n. exc. 4.00 sqm each including removing from site complete all as specified and directed. |
| 5 | Taking down chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each including removing from site complete all as specified and directed. |
| 6 | Taking down shutterexc. 1 Sqm and n.exc 2 Sqm each and refixing the same opening after resecuring or easing and adjusting shutters of any description.complete all as specified and directed. |
| 7 | Taking down Shutters of any description n. exc 2 sq. m each of any description complete all as specified and directed. |
| 8 | S&F first class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. |
| 9 | M&L for 40 mm thick flush shutters, solid core construction, exterior grade with block board core and plywood face, pannels, commercial type on both sides and one face is covered withdecorative face veneer with lipping / frame to match, including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed. |
| 10 | S&F factory made glazed and Skelton 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded,mitred and rebated sash bars, any numbers , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc; sizes of members of shutters as specified in SSR Part-I section 8, clause 8-24 (a)complete all as specified and directed. |
| 11 | S&F solid PVC door frame of size 50mmx 47mm made out of 5 mm plain/ colour PVC sheet reinforced with MS square tube as per specification & drawingsspecified in SSR Part-II 2010 complete all as specified and directed. |
| 12 | Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on eitherside and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing in SSR Part II 2010 etc complete all as specified and directed. |
| 13 | M&L PVC SHEET of wall paneling of thickness 5mm solid consisting of panels of desired size stuck on inner frame work of 50mm wide strips of 5mm thick prelam PVC sheet. The panel & strips shall be of 600 kg / cbm density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. A groove of 2mm may be left at the joint of two panels for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a U Channel at top, bottom and side edges andstrips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement with and complete all as specified and directed. (Note- Including all nesscesary fittings and scafolding for heighted site) |
| 14 | S & F in repair 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frames complete all as specified and directed |
| 15 | S& F Factory Made Solid PVC coulour Moulded Door Shutter with wood free EPS, 28 to 30 mm thick (stiles),with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm Plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawingNote: Colour approved by GE / Engr-in-Charge |
| 16 | S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed complete all as specified and directed. |
| 17 | S&F 100 mm sizemild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed. |
| 18 | S&Faluminiumhandles, cast type, anodised 150 mm size completeall as specified and directed. |
| 19 | S&F floor door stopper double leg of aluminium alloy bodyof 140 mm length with aluminium base plate of size 50 mm x 40 mm complete all as specified & directed. |
| 20 | S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed. |
| 21 | S&F 150 mm, mild steel ordinary helical door spring including roller and roller plate including necessary welding if requriedcomplete all as specified & directed. |
| 22 | S&F in repair aluminium (die cast) bodydoor closer hydraulically regulated, designation No.3 universal type, suitable for doors shutters up to 1000 mm in width and of weightbetween 61 to 80 Kg and fixed complete all as specified and directed. |
| 23 | S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including lettingfor cabinets fixed with screws complete all as specified and directed. |
| 24 | S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm completeall as specified and directed. |
| 25 | S&F in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed with tinned tacks or galvanised wire staples, complete all as specified and directed. |
| 26 | S&F in repairdrapery rod 25 mm dia, high Strength PVC Coated MS rod of thickness 40/60 microne of wood finish with minimum 8 ringsin each metrelength of rod of ABS Plastic in matching colour & installations brackets of galvanised steel with all accessories complete all as specified and directed. |
| 27 | S&F in repair venetian blind coloured powder coated 35mm wide and 1 mm thick Aluminium alloy blades with opening and closing arrangment including aluminium hanging channel at top with sliding wheel/ring including pulling rope in both side and necessary accessories complete all as specified and directed. |
| 28 | S&Fbrasshandles, cast type, polished bright 100 mm size completeall as specified and directed. |
| 29 | S&F mild steel for framed work such as grills, gratings, etc With ends of bars shouldered and riveted, or forged into spikes, framed guard bars, barred iron doors ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con-forming to Fe. 290. Gde-E-165 complete all as specified & directed. |
| 30 | S&F powder coated aluminium frame for doors, windows or partition including aluminium beading, hinges of required size,jointing cleats, screws, dash,fastners,plug for fixing with wall, columns etc complete all as specified & directed. |
| 31 | S&F powder coated of any colour aluminium door shutters, aluminium section like lock rail, bottom rail 115mmX38mmX1.00mmthick and top rail and vertical rail 100mmX38mmX1.00mm thick mm including necessary jointing cleats/glazing clipx, rubber neorene paking, handles 02 Nos in each door, locking arrangment, aluminium snap beading screw etc, complete all as specified and directed. (panels likes prelaminated particle board / sheet glass shall be measured and paid seprately) |
| 32 | S&F Powder Coated aluminiumwindow and ventilator shutters side hung type without sash bars, , aluminiumsection weighing not less than 0.55kg/m includingnecessary jointing cleats/ glazing clips,rubber neoprene packing, anodised aluminium snap beading , screws, anodised aluminium fittings such as peg stay 150mm long (1 No) hinges typeB-21 100mm long ((2 Nos) suitable handle (1 No)with and including taking down existing shutter complete all as specified and directed. |
| 33 | S&F powder coated 3 track aluminium sliding window three track with two glass shutters using 4 mm thick glass tinted modi guard and one shutter with stainless steel wire gauge wire cloth 0.31 mm stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperature 1.61 mm using aluminium powder coated section aluminium cleat, PVC track, beading handle, lock, rubber beading etc complete fittings as per manufacture instructions. Note:- Size of aluminium section are as under:-(i) Three track top and vertical - Jindal main 2010 section No 20621 or equivalent as approved by GE(ii)Three track bottom- Jindal main - 2010 section No 20620 or equivalent as approved by GE(iii)Shtter vertical section- Jindalmain 2010- section No 20606 or equivalent as approved by GE(iv)Shutter top and bottom- Jindal Main- 2010 Section 20604 or equivalent as approved by GE(v) shutter verticle middle ( Interlock) - Jindal main - Sectionor equivalent approved by GE. |
| 34 | S&F 5 mm thick aluminum composit pannel fixed or laid on door or partition by using rubber based adhesive complete all as specified & directed. |
| 35 | Preparing surfaces, holding the members in true position and welding in reparis exc 2.5 cm n. exc 5cm in length, thickness of metal to be welded exc 6 mm but n. exc9mmcomplete all as specified and directed. |
| 36 | S&F19 mm thick Solid PVC board fixed with steel screw and synthetic adhesive both one side balancing color texture used for shutter of the cabinet / cupboard and completeall as specified and directed. |
| 37 | S&F19 mm thick Solid PVC board fixed with steel screw and synthetic adhesive both side balancing white texture used for shutter of the cabinet / cupboard and completeall as specified and directed. |
| 38 | Providing & fixing false ceiling at all heights with perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter- locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L- shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. |
| 39 | M&L forcleaning of roof slab,parapets and beamsincluding picking, sweeping clean and washing down with water to remove dust & providing water proofing treatment with polymeric standard water proofing membrane, complete all as specified and described as under :-(a)Preparation of surface and applyingonepriming coat of cold bituminous primer@ 0.30 kg / sqm.(b) Supply & providing APP modified polymeric water proofing. membrane 3 mm thick of weight not less than 3.60 kg / sqm reinforced with polyester non-woven fabric (weight not less than 150 gms/Sqm) centre core including coating the surface with the compatible primer and torch application of membrane with minimum 10 cm overlaps in sides and 15 cmoverlaps in endas required thereof, complete all as specified and directed. (c) Applying one more coat of polymeric modified bitumen 85/25 @ 1.2 Kg/Sqm over which one coat of aluminium bituminous paint @ 0.10 Kg/Sqm shall be applied. NOTE:- The work of water proofing treatment shall be got executed throughh expert team of manufacturers or authorised applicator of manufacturer as approved by GE. |
| 40 | M&L granite stone18 to 20 mm thick glazed (table rubbed and polished) fixed as in plateform and the like set in cement mortar 1:4and pointed with white cement(1:2) usingmarble dust with admixtureof pigment to match the shade of slab and exposed edges rounded with & includingscreed bed or beeding layer of mortar 1:4 for layingfloor finishes complete all as specified and directed. |
| 41 | M&L for 75 mm thick for cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in subbase for laying floor finishes complete all as specified and directed. |
| 42 | M&L for 75 mm thick PCC 1;3:6 type C-2 using 40mm graded stone aggregate as in plinth protection or similar places and finishing the surface even & smooth with out using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meter and every change of direction and filling the same with mixture of bitumen & sand in ratio (1:1) by weight including necessary form work complete all as specified and directed. |
| 43 | M&L for non skid Ceramic tiles,first quality( of approved class , colourand design/ shade )6 to 7 mm thick( square/ rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floorsurfaceetc set and jointed in neatcement slurry and pointed in coloured cement to match with coloured tiles overand including 15 mm Screed bed in CM 1: 6 withcomplete all as specified and directed. |
| 44 | M&L for non-skid colouredceramic tiles first quality (of approved class, colour and design/shade) 7 to 8 mm thick (square/rectangular)asin skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including 10 mm thick rendering in cement mortar (1:4),with complete all as specified and directed. |
| 45 | M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of size 300x200x7mm/ 350x250x7mm/ 450x350x7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed. |
| 46 | M&L vitrifiedcoloured tiles 10 mm thick light shade(square/rectangular) asin floors etc set and jointed in neat cement slurry area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm and pointed in white or coloured cement to match including 15 mm thick cement screed bed in cement mortar 1:6 for laying floor finishes with complete all as specified and directed. |
| 47 | M&Lvitrifiedcoloured tiles 10 mm thick dark shade(square/rectangular)as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including 10 mm thick rendering in cement mortar (1:4), rough finish to receive the tilescomplete all as specified and directed. |
| 48 | M & L for taking down old cement plaster/Grit wash on stone wall or bricksurfaces of walls including raking out joints, hacking for key and scrubbing down with water with and including, removing debris out sideMOD Land at contractor is own arrangement) complete all as specified & directed. complete all as specified and directed. |
| 49 | M&L for taking down/dismantling of existing roof treatment / cement plaster/ tiles of any description such as PCC Padding/ Coba treatment/ mud phuska/Lime conc terracing including screed bed etc. Hessian base felt/tar feltetc. (any type and thickness) with and including, removing debris out sideMOD Land at contractor is own arrangement) complete all as specified & directed. |
| 50 | M&Lfor Rendering 15 mm thick on fair faces of concrete /brick surface in cement mortar 1:6finished fair andeven as in wall etc complete all as specified and directed. |
| 51 | M&L for Rendering 15 mm thick on fair faces of concrete/brick surfaces in cement mortar 1:4mixed withwater proofing compound as per manufacturer\"s instruction, finished fair and even without using extracement etc complete all as specified and directed. Note :- WPC shall be measured and paid forseprately as supply only under respective item of sch A. |
| 52 | M&Lfor Rendering 10 mm thick on fair faces of concrete /brick surface in cement mortar 1:3finished even and smooth without using extra cementas inceiling and similar other work complete all as specified and directed. |
| 53 | M & L for repair to chajjas including necessary cement concrete type B-0 (1:2:4)12.5 mm graded stone aggregate and15mmthick plastering in CM 1:4 to disturbed portion and finishing the surface with two coats of cement base paintincl preparation of surface complete all as specified and as directed. |
| 54 | M&L for preparing old surfaces of walls plastered by brooming down with steelor wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , washing rubbing down and stopping of distempered and painted surface & removing all vegetation growth, nails and making good holes,cracks etc complete by necessary puttyand make the surface smooth by rubbing with sand papers etc andapplying one coat of distemper oil emulsion on old prepared surfaces of walls completeall as specified and directed. |
| 55 | All as per item no 54 above but on Ceiling Surface, Complete all as specified and directed. |
| 56 | M&L for preparing old surfaces of walls plastered plastered by complete removal of existing treatment by electric grinder brooming down with steelor wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , washing rubbing down and stopping of distempered and painted surface & removing all vegetation growth, nails and making good holes,cracks etc complete by necessary putty as per manufacturer\"s instruction on existingprepared surfaceand make the surface smooth by rubbing with sand papers etc andr applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and including 3 mm thick water proof wall care puty in twocoat or layers complete all as specified and directed. |
| 57 | M&L for prepration of new plaster surfaces of wall and applying two coat of oil bound distemper over and including a coat of alkali primer & 3 mm thick wall care puttty complete all as specified and directed. |
| 58 | M&L for complete removal of existing treatement by scraping, washing, rubbing down or stopping distempered or painted surfaces etcof walls plastered or un-plastered & removing all vegetation growth, cleaning & applying of Birla/JK white wall putty approx 1 mm thickas per manufacturer\"s instruction on existingprepared surface and make the surface smooth by rubbing with sand papers etcand applying two coats of oil emulsion distemper over a coat of water proof primercomplete all as specified and directed. |
| 59 | M & L for preparation of newly plastered surfaceof wall and applying two coat of cement base paint complete all as specified and directed |
| 60 | M&L for Complete removal of existing treatment of old surface and washing rubbing down and stoping of distempered and painted surfaceof wall and applying two coats of cement based paint complete all as specified and directed. |
| 61 | M&L for coloured 3D/2D PVC Vinyl wall cladding/convering/wall paperminium 3 mm/ 5 mm thick on fixing on vertical/horzental surface on wall /celing with necessary dheshive/fitting,fixture or as per manufacturers instruction complete all as specified and directed |
| 62 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames glazed with putty or fixed with beadsincluding punching or drilling out old glazing pins/spring clips etc complete all as specified and directed. |
| 63 | S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5Sqm in each pane complete all as specified and directed. |
| 64 | S&F Sheet glass 5mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5Sqm in each pane complete all as specified and directed. |
| 65 | M&L for 4 mm thick figured glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each panecomplete all as specified and directed. |
| 66 | M&L for 10 mm thick toughendglass in partition or fixed to aluminium/steel/wooden frame of any size asdesired including polishing round edges frosted type fixed with SS frame/clips/ wall by embedding inside etc complete all as speified and as directed. |
| 67 | M&L for preparing of old painted wooden surfaces over 10cm width or girth and making good including knotting and stopping,cleaningetc complete by necessary puttyand make the surface smooth by rubbing with sand papers etc andapplying one coat of synthetic enamel paint on old prepared surfaces of wooden completeall as specified and directed. |
| 68 | M&L for preparing of old painted steel surfaces over 10cm width or girth and making good with & including by necessary red lead puttyand make the surface smooth by rubbing with sand papers etc andapplying one coat of synthetic enamel paint on old prepared surfaces ofsteel completeall as specified and directed. |
| 69 | M&L for preparation of new or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed |
| 70 | M&L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed |
| 71 | S&F in repair vitreous china wash hand basin (flat back) of size 550x400mmincluding one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector,MS brackets 2 numbers including cutting for and pinning in ends of brackets and including removing WHB outside MOD Land complete all as specified and directed. |
| 72 | S&F in repair for 600x450mm beveled edge looking mirror of selected quality glass 4 mm thick mounted on 6mm thick AC building board or commercial ply woodand fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified & directed. |
| 73 | S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic actiontype with inlet ball valve and float, handle with & including bracket andPVC flush pipe 32 mm borecomplete all as specified and directed. |
| 74 | S&F PVC conections 15mm size with PTMT nuts of 450 mm long fixed in repair complete all as specified & directed. |
| 75 | Taking up or down existing GI tubing and connections, including cleaning for refixing and making good the disturbed surface for 20 mm dia pipes complete all as specified and directed. |
| 76 | Taking up or down existing GI tubing and connections, including cleaning for refixing and making good the disturbed surface for 15 mm dia pipes complete all as specified and directed. |
| 77 | S&F for laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing \"medium grade\" with and including all GI fittings such asunions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floorscomplete all as specified and directed. |
| 78 | S&F for laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing \"medium grade\" with and including all GI fittings such asunions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floorscomplete all as specified and directed. |
| 79 | S&F in repair Pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore, complete all as specified and directed. |
| 80 | S&F in repair bib taps long body cast copper alloy chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and as directed. |
| 81 | S&F in repair for Chromium plated brass angle valve for 15mm bore pipe,complete all as specified and as directed. |
| 82 | S&F in repair for Chromium plated brass angle valve two way for 15mm bore pipe,complete all as specified and as directed. |
| 83 | S&F in repair 15mm bore, CP two way Bib taps fancy type long body , half / full turn , screwed down for iron pipes. complete all as specified and as directed. |
| 84 | S&F in repair Stop valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipes or for unions, 15mm dia of pipe, complete all as specified and as directed. |
| 85 | S&F in repair Stop valves, cast copper alloy, screwed down, high pressure, with capstan head, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 20mm bore, fixed in repairs complete. |
| 86 | S&F in repair Chromium plated brass shower rose125 mm dia with swivel joints, fixed in repairs complete all as specified and directed. |
| 87 | S&F in repair Chromium plated brass shower rose75 mm dia with swivel joints, fixed in repairs complete all as specified and directed. |
| 88 | S&F in repair Center hole basin mixer 15mm dia chromium plated brass with costed swinging spout including plugging and securing to walls, complete all as specified and as directed. |
| 89 | Supply & Fixing of 15mm bore CP wall mixter with telephonic shower with tube and hook of complete all as specified and as directed. |
| 90 | Repairs to leaking water in pillar tap, stop cock, angle valve, bib taps of any description by replacing the washer complete all as specified and as directed. |
| 91 | S&F in repair Spindles for 15mm brass or CP brass stop cocks, bib taps etc, complete all as specified and as directed. |
| 92 | S&F in repair Galvanised iron medium grade fittings as under for 15mm bore pipe :- |
| 93 | Union |
| 94 | Tee |
| 95 | Long screw |
| 96 | Socket |
| 97 | elbow |
| 98 | Nipple |
| 99 | S&F in repair PVC flush pipe 32 mm dia for low level flushing cistern, complete all as specified and as directed. |
| 100 | S&F in repairs vitreous china urinals, flat back of size 465mmx355mmx265 mm, white minimum incl grating and union for discharge pipe complete incl providing & fixingplugs, bedding urinal against wall in cement mortar 1:2, securing urinals plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and as directed. |
| 101 | S&F in repairs vitrious china squatting pan Orissa pattern size 630 x 450 mm white , with integaral foot restincluding P trap complete all as specified and directed. |
| 102 | S&F in repair Europeanwall mounted white vitreous China wash down water closetincluiding hydroulicSeat cover made using high quality made using high quality material fine finishing for elegant asthetic look P/S trap and fulsing arrangement,fixing bolts, flushing cistern ,connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. with complete with fixing arrangement fancy look complete all as specified and directed. |
| 103 | S&F in repair table topvitreous china wash hand basin (flat back) of size 550x400mmincluding one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector,MS brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed. |
| 104 | S&Fin repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long, complete all as specified and as directed. |
| 105 | Disconnecting & taking down existing water tank of capacity exc 250 litres and not exc. 500 litres and removing from site complete S&F rotational moulded polyethylene water storage tanks 500 litres capacity (cylindrical verticalwith closed top) hoistedwith and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part Icomplete all as specified and directed. |
| 106 | S&F in repair PVC (SWR) pipes, double socketed, in any length with rubber ring joints, fixed to walls 110mm bore complete all as specified and directed. |
| 107 | S&FPVC (SWR) bends any radius, 110mm bore complete all as specified and directed. |
| 108 | S&F in repair Stainless steel sink 1.00 mm thick with drainage board for kitchen ,with plug waste pipe, washers including cantilever cast iron bracket ,connecting union over all size 915mmx460mm with bowl size 410mmx330mmx160mm complete all as specified and directed. |
| 109 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed. |
| 110 | Demolition of cement concrete (unreinforced) of any description as in ground floors and pavings not exceeding 15cm thickness (above or below ground floors) with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed. |
| 111 | Dismantling of wall and ceiling boards any thickness including cover filletes with and including with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed. |
| 112 | Notes for item No. 1 to 111 (i) The work will be carried out upto 6th storey bldgs. Hence necessary complete scaffolding and other safety arrangements will be managed and made by tenderer/ Contractor accordingly at own expense. (ii) Tenderer kind attention is also invited to srl clause 1.16 of Sec-I on srl page No 1 to 150 (General rules for Safety in Construction) as specified in SSR Pt-I (2009) for safety measures/ precautions.(iii) Steel scaffolfing is to be used in the work. (iv) Necessary arrangement for temporary plug the / door / window / ventilator opening at time of taking down plaster/ new plaster till completion of work. Made by Tender / Contractor at own expense. |
