Tender For Improvement To Hanger No. T-91 And Cafetaria At 45 Sqn
Tender Value
Ref. Documents
Estimated cost
Bid Submission
14 Feb 2026
0 days left
EMD
97000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
sulur → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Improvement To Hanger No. T-91 And Cafetaria At 45 Sqn
BOQ
| Sl. No. | Item Description |
| 1 | SCHEDULE A BOQ |
| 2 | Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 3 | M&L 100mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate Finished even & smooth without using extra cement complete all as specified and directed. |
| 4 | M&L Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound complete all as specified and directed. |
| 5 | M&L Excavating over areas, n exc 1.5 m deep and getting out in hard/ dense soil complete all as specified and directed. |
| 6 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed offine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. |
| 7 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 8 | Repairs to existing hanger steel sliding door shutter of leaf of size 4.50 M (clear width) 6.00 M (clear height) of each,straightening of worn-out top & bottom rails,replace unserviceable existing rollers, tightening/replacing the loose nut and bolts,necessary/required welding of rails with hanger structure, replacaement of broken locking arrangement etc,oiling ,greasing ,etc and one coat of aluminium paint to complete door structure etc for smooth functioning of hanger door shutter all as specified. |
| 9 | S&F 4 mm thick, sheet glass, ordinary quality and glazingwithoil putty /beedingin squares n.exceeding 0.5 sqm each pane for fixing to aluminium/wooden joinery work incl hacking out old broken glass complete all as specified. |
| 10 | S&F in repairs stainless steel wire cloth, 0.36mm dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed by Engineer-in-Charge. |
| 11 | Dismantling to Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed |
| 12 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of and colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed by Engineer-in-Charge |
| 13 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws as specified and as directed by Engineer-in-Charge |
| 14 | Dismantling of false ceiling boarding, any description, fixed or laid /inserted incl timber /GI/ aluminium frame work with screws in ceiling flat or slopingcomplete all as directed. |
| 15 | M&L MS framed, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing for false ceiling (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed. |
| 16 | M&L for preperation of new steel surface Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of aluminium paint over a coat of red oxide complete all as specified and directed. |
| 17 | M&L for preperation of old steel surface Surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of aluminium paint complete all as specified. |
| 18 | M&L Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, eachscrewed end to be fitted with washers and one hexagonal or squarenut, n exc 5cm long complete all as specified and directed. |
| 19 | M&L Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified. |
| 20 | S & F False ceiling using6mm thick fibre cement designer false ceiling board all as specified and directed by Engr -in- Charge. |
| 21 | S&F grills for air circulation for turbo ventilator made with powder coated aluminium frame of size 600mmx600mm fixed in false ceiling grid thickness not less than 2mm complete all as specified and directed. |
| 22 | M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 23 | M&L 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice laminationfixed with screws to frame work all as specified and directed. |
| 24 | Surface dressing n exc 15 cm deep in hard/dense soil complete all as specified and directed. |
| 25 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard dense soil complete all as specified and directed. |
| 26 | M&L Cement concrete 1:4:8 type D-2 (40mm grade aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 27 | M&L Brickwork with fly ash bricks, modular size straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed. |
| 28 | M&L Brickwork with flyash bricks, modular size straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed. |
| 29 | Removal of excavated material to a distance exceeding 1.50 Km andnot exceeding 5.00 Km and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. |
| 30 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. |
| 31 | M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 complete all as specified and as directed. |
| 32 | M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 with smooth finish without using extra cement complete all as specified and directed. |
| 33 | M&L Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM 1:3 with smooth finish without using extra cement complete all as specified and directed. |
| 34 | M&L Preparing new surfaces ofplastered or unplasteredwall and applying two coats of cement based paint over one coat of alkali resistant primer complete wash complete ll as specified and directed. |
| 35 | M&L Preparation of new plastered surfaces of wall by applying three coats of white wash complete all as specified and as directed. |
| 36 | M&L Preparation of new plastered surfaces of ceiling by applying three coats of white wash complete all as specified and as directed. |
| 37 | Supply only liquid water proofing compound complete all as specified and directed. |
| 38 | M&L Hardcore of broken stone or boulder gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 39 | M&L 100 mm thick Plain cement concrete1:4:8type D-2(using 40 mm gradedstone aggregate ) as in sub base complete all as specified anddirected |
| 40 | M&L 40mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate Finished even & smooth without using extra cement complete all as specified and directed. |
| 41 | M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in D4 neat cement slurryand pointed in white or coloured cement to match set and jointed in neat cement slurry and pointed in white or coloured cement to match incuding screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) complete all as directed. |
| 42 | M&L Glazed ceramic coloured tiles 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dadoincluding 10mm thick 1:3 backingcoat complete all as specified and as directed. |
| 43 | M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 44 | M&L 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ringjoints fixed to wallincuding taking down existingcomplete all as specified and as directed. |
| 45 | M&L 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ringjoints fixed to wall complete all as specified and as directed. |
| 46 | PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. |
| 47 | S&F PVC (SWR) 75mm borevent cowl complete all as specified and as directed by Engineer-in-Charge. |
| 48 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified. |
| 49 | S&F Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails.MS frame shall be covered with heat moulded plain colour PVC\"C\"channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail.Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitablePVCsheetbeadingand jointed together with solvent cement complete all as specified. |
| 50 | S&F Butt hinges 100 mm long medium weight cold rolled stainless steel complete all as specified and as directed. |
| 51 | S & F Aluminum handles cast type anodised 150 mm long complete all as specified and as directed. |
| 52 | Supply and fixing 150 mm long aluminum anodized barrel tower bolt extruded section complete all as specified and as directed. |
| 53 | S&F 250mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminum alloy and fixed complete all as specified and as directed. |
| 54 | M&L cement concrete 1:2:4, Type B1 (using 20 mm graded stone aggregate) cast in situ in lintels/chajjas up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed completeall as specified and directed. |
| 55 | Supplying and laying of 25 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 56 | Supplying and laying of 20 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 57 | S & F 20mm outer dia of pipes CPVC gate valves as per requirement of sites complete all as specified and directed. |
| 58 | S & F 25mm outer dia of pipes CPVC gate valves as per requirement of sitescomplete all as specified and directed. |
| 59 | M&L Vitreous China wash down water closet pan (pedestal pattern), white (excluding flushing cistern and incl flush pipe) complete all as specified and directed. |
| 60 | M&L Plastic water closet seat closed pattern with flatbottom, and cover and mild steel chromium plated hinging device complete all as specified and directed. |
| 61 | S&F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flushing pipe complete all as specified and directed. |
| 62 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 63 | S&F Vitreous China Urinal, full stall type, white excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed. |
| 64 | S&F CP Urinal spreaderfor fixing with 15 mm dia pipe complete all as specified and as directed. |
| 65 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 66 | M&L PVC (SWR) 110mm bore P Trapincludingcomplete all as specified and as directed. |
| 67 | Supply and fixing factory made UPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension,including Pinhead Glass with thickness of 4mm required for fixed & louvers strips, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance inimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 68 | M&L 75mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded mechanically crushed stone aggregates),as in hard standing/ plinth protection complete all as specified and as directed. |
| 69 | M&L Doom grating 125mm diaof SS (minimum weight 40gms) complete all as specified and as directed by Engneer-in-Charge. |
| 70 | M&L fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed |
| 71 | M&L WHB, vitreous china (flate back or angle back type) ofsize 550x400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe Complete all as specified . |
| 72 | S&F 32 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer- In - charge |
| 73 | M&L 32 mm low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm for WHB complete all as specified and as directed by Engineer-in-Charge |
| 74 | S&F Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. |
| 75 | S&F 15mm fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 76 | S&F 15mm fancy type chromium plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 77 | M&L PVC connection 15 mm size with PTMT nuts of length 450 mmi complete as directedby Engr-in-charge. |
| 78 | S&F Wall mounted Shower Arms 200mm long flat shapefor wall mounted shower with flange complete all as specified and directed . |
| 79 | S&F Over head Shower rose chrome Plated complete all as specified and as directed. |
| 80 | M&L 1000 lit capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed. |
| 81 | S&F 25mm Ball valves high pressure of PTMT withepoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed. |
| 82 | M&L Reinforced cement concrete M-25 nominal mix (using 20 mm graded stone aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 83 | M&L Reinforced cement concrete M-25 nominal mix (using 20 mm graded stone aggregate) in Chajjas complete all as specified and directed. |
| 84 | M&L Reinforced cement concrete M-25 nominal mix (using 20 mm graded stone aggregate) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 85 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 86 | Formwork to chullah hoods, chajjas, troughs and similar items includingedges complete all as specified and directed. |
| 87 | Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etccomplete all as specified and directed. |
| 88 | M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and includingmild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 89 | M&L TMT bars 5mm to 10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and includingmild steel wire (annealed) not less than 0.9mm dia or securing with clipsin stirrups , spacers and binders etccomplete all as specified and directed. |
| 90 | M&L Framed work such as grills, gratings, angles etc. with ends of bars shouldered and/or riveted, or forged into spikes; framedguard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of static water tanksand similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed by Engineer-in-Charge. |
| 91 | M&L Water proofing treatment of existing roofs as per details given below after complete removal of existing water proofing treatment and expose of top surface of RCC slab of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with water and using wire brush including removing debris to outside the MOD land complete all as specified and as directed :- |
| 92 | (a) Surface should be free from any loose paint, dust or grease.Remove all existing bitumen coatings completely by using intense wire brushing, high speed water jet & vacuum cleaner for thorough cleaning of the surface to avoid ‘Peeling off’ problems.(b) All cracks at corner joints, channels and parapets should be properly treated.For filling cracks upto 3mm crack seal material of M/s Asian paints or equivalent inM/s Dr Fixit or M/s Pidilite or M/s Sika chemical to be used. Bigger cracks, damagedportions & hollow areas must be repaired with polymer modified cement mortar.(c) Apply a coat of self priming smart care damp proof ultra (Code 5698) ofM/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical with 33% dilution with water using brush/roller on newly plastered surface after curing as per IS-456 and allow to dry for 4 to 6 hours (dilution & forced coverage requirement strictly as per manufacturer’s instructions).(d) After the primed surface has dried, apply first coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemicalusing brush/roller on the same primed surface & allow to dry for 4 to 6 hours.(e) Prepare for apply 2nd coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemicalusing brush/roller on the same surface.The temp to be maintained 25 to 35° C through out the all above application work.(f) In case of severe dampness an additional coat of damp proof materials to be applied. |
| 93 | Note :(i) The work shall be carried out through authorized and qualified applicators of the following manufacturers only. MOU to be submitted before commencement of work. Make : M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical.(ii) A performance guarantee certificate for 10 years shall be submitted by the contractor to the GE on completion of work as specified. |
| 94 | M&L Plain cement concrete 1:3:6, type C2 (using 20mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and as directed. |
| 95 | M&L Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed. |
| 96 | M&L Precast RCC 1:2:4, Type B–1 using 20mm graded stone aggregate as in landings, cover slabs, chullah hoods, Chajjas, water troughs, mangers, Shelves and similar articles with plain faces including formwork, set in cement mortar 1:4 complete all as specified and as directed. |
| 97 | M & L Providing 75mm thick plain cement concrete 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in sub base etc complete all as specified and as directed. |
| 98 | M&L Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width type C-1 1:3:6 using 20mm graded stone aggregate and setting in mortar 1:6 straight or curved on plan exc 6m mean radius, built incement mortar 1:6 complete all as specified and as directed |
| 99 | Providing and laying Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and colour pigment complete all as specified and as directed |
| 100 | M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed |
| 101 | S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed |
| 102 | S&F Sink Cock with 150mm long swivel spout and wall flange CAT part No F2014261 of CERA or CAT part No T5821A1 of Parryware or equivalent complete all as specified and as directed |
| 103 | S&F Brass chromium plated bottle traps 32mm bore dia for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed. |
| 104 | S&F 75mm dia PVC (SWR)bends any radius complete all as specified and as directed |
| 105 | Taking down carefully copper/Alu point wiring (light, fan. socket or power) complete including fixtures and fitings such as switches, ceiling roses, pendents, regulators, sockets , light fitting etc and removing materialsto store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separetely) and making good distrubed surfaces of walls, floors etc complete all as specified and directed. |
| 106 | M&L Wiring complete with 1.5 sqmm single core PVC insulated, unsheathed FRLS 1100 volts grade,FRLS cable and incl PVC Casing Cappingwith accessories in wall/roof/ceiling/hangar steel frames etc incl Modular terminal boxes fabricated with 1.6mm MS sheet concealed/fixed surface to wallscovered with plastic laminated top cover 2.8mm fixed with cadmium plated iron screws etc and 1.5 sqmm PVC insulated, unsheathed copper conductor multistrandedcable 1100V grade as earth continuity conductor & connecting to common earth dolly all as specified for |
| 107 | One light point/ fan/ bell point controlled by one switch |
| 108 | All as per item No 105 here in before but for one switch socket outlet 3 pin 5 Amps on independent board |
| 109 | All as per item No 104 above but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently |
| 110 | S&F modular switch 1 way 6 Amps, 1 module complete all as specified and directed. |
| 111 | S&F modular switch 1 way 16 Amps, 1 module complete all as specified and directed. |
| 112 | S&Fmodular socket outlet multipurpose 2/3 pin 6 amps, 2 module complete all as specified and directed. |
| 113 | S&Fmodular socket outlet multipurpose 2/3 pin 6/16 amps, 2 modulecomplete all as specified and directed. |
| 114 | S&F white cover plate with frame, 3 Module complete all as specified and directed. |
| 115 | S&F white cover plate with frame, 4 Module complete all as specified and directed. |
| 116 | S&F white cover plate with frame, 6 Module complete all as specified and directed. |
| 117 | S&F white cover plate with frame, 8 Module complete all as specified and directed. |
| 118 | S&F metal flush box 3 module complete all as specified and directed. |
| 119 | S&F metal flush box 4 module complete all as specified and directed. |
| 120 | S&F metal flush box 6 module complete all as specified and directed. |
| 121 | S&F metal flush box 8 module complete all as specified and directed. |
| 122 | S&F electronicmodular fan regulator 230 volts, step type socket type, hum free 120 watt 2 Module complete all as specified and directed. |
| 123 | S&F ceiling rose, surface type Bakelite 65x55mm3 terminal complete all as specified and directed. |
| 124 | S&F 36 Watt LED Luminaire suitable for 600x600mm modular ceiling grid/surface/roof including frame of suitable size of above LED light with high efficiency PMMA diffuser gives soft glare free light with available lumen output from notless than 110 lumens/watt.The 36 W system shall be operating at 220-240v AC supply having internal driver .IP20,surge protection not less than 2KV ,permisible limit of CRI range,with recommended burning hours,4000K/6500Ketcfrequency 50 to 60 Hz ,with 70% lumen maintenance upto 50000 Br Hrs with uniform visually comfortable light output at 150 degree beam spread , . PF should be notless than0.95 , THD < 10% . Indivisual LED\"s should not be visible for glare free output ,colour temperature 6500k all as directed. |
| 125 | Supply and fixing 4 feet, LEDlight fitting 18 watts(T-8) with out put of not less than 110lumens/watts , boxtype made with epoxy white powder coated CRCA sheet steel(decorative) light fitting having G13 bipin holders compitable for mounting on wall/ceiling/surface,ermisible limit of CRI range,with recommended burning hours ,4000K/6500Ketc , 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driverconnector block etc complete with all accessories internally pre wired andnecessary mounting arrangements, including provision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting with integrated driver ofLED tube rod 4\" x 18 watts complete all as specified and as directed. |
| 126 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet 9/10 Watt LED light fitting batten typewith Luminaries & integrated driverbatten with lumen out notlessthan 110 lumens/watts & housing extrudedpolycorbanate housing square shaped diffuse,permisible limit of CRI range,with recommended burning hours,4000K/6500Ketcsuitable for mounting on wall/surface/ceiling including taking down old unserviceable fittings any type complete all as specified and as directed. |
| 127 | Supply and fixing LED Building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including pipe. |
| 128 | S & F new Energy saving new generation 10 watts with lumen effiency not less than 100lumens/watt,LED bulk head fitting IP 65 luminaire with opel diffuser pre wired andnecessary mounting arrangements ,permisible limit of CRI range,with recommended burning hours,4000K/6500Ketcprovision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb and removal old existing unsv tube light fitting complete all as specified and as directed.. |
| 129 | Supply and fixing new energy efficeint Ceiling fan 1200mm sweep(BLDC), energy efficient ISI mark with 5 star rating 230 Volts AC 50 Hz, single phase including provision of fixing arrangement, nut and bolt andflexible 3 core of suitable size long complete including taking down existing one, writing MES No with synthetic enamel paint all as specified and as directed. Note:-(a)The contractor shall given a written guarantee of minimum two years from completion of work.(b)Old Unserviceable ceiling fan shall be deposited to MES store yard. |
| 130 | Supply and fixing down rod15 mmmedium grade GI tube fxingfor ceiling fan with necessary cutting, screwing and fixing on angle iron all as specified and directed |
| 131 | Supply and fix new Exhaust Fans 300 mm sweep, 230 volt square type, heavy duty,1400 RPM, corrosion less mild plastic body of motor, plastic/ fibre blade for noise less operation,self operating louvers gives powerful performance round the clock,including necessary cutting, making holes on stone/brick walls where required, fixing arrangement with MS pipe 350 mm dia of required length for protect deshape of stone masonery, suitable hold fast with necessary nut, bolts / screws including taking down existing one writing MES No with synthetic enamel paint all specified and directed. Note:-Old Unserviceable domestic exhaust fan shall be deposited to MES store yard |
| 132 | Supply & fix lamp holder, insulated body, cord grip pattern SP 230 volt, 50Hz,including takng down old u/s complete all as specified and directed.. |
| 133 | Supply & fixing 9 watt LED lamp inbuit driver complete all as specified and directed. |
| 134 | Supply and fixing replacementfactory madepowder coated distribution board TPN 4 way vertical type, double doorincludingbus bar, Neutral bar, standard DIN rail, earth bar acomplete all as specified and directed |
| 135 | Supply and fixing replacementfactory madepowder coated distribution board SPN 8 way, double doorincludingbus bar, Neutral bar, standard DIN rail, earth bar acomplete all as specified and directed |
| 136 | S&F Triple pole Nuetral MCB 63 Amp , 415 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacitycomplete conforming to IS 8828 of 1996 all as specified |
| 137 | S&F MCB SPN32 Amp , 240 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacitycomplete conforming to IS 8828 of 1996 all as specified |
| 138 | Supply and fixing singlepole MCB 6 to 32 Amps, 240 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacity conforming to IS 8828 of 1996all as specified |
| 139 | Sub main wiring for circuit complete with 2 X 6 sqmm single core PVC insulated, unsheathed FRLS1100 Volt grade multi stranded copper conductor cable drawn through and incl suitable dia metallic Steelconduit and accessories complete fixed surface to wall/roof/ceiling etc and incl 1 X 6 sqmm single core PVC insulated, unsheathed FRLS 1100v grade multi stranded copper conductor cable as earth continuity conductoretc and all as specified: |
| 140 | Sub main wiring for circuit complete with 2 X 4 sqmm single core PVC insulated, unsheathed FRLS1100 Volt grade multi stranded copper conductor cable drawn through and incl suitable dia metallic Steelconduit and accessories complete fixed surface to wall/roof/ceiling etc and incl 1 X 4 sqmm single core PVC insulated, unsheathed FRLS 1100v grade multi stranded copper conductor cable as earth continuity conductoretc and all as specified: |
| 141 | Supply,installation and commissioning advanced day lighting system of 750 mm Light Pipe with Dome + Diffuser + Flashing Plate with thefollowing accessories of 2.4 MtrsLength complete all as specified and directed. Make : Sky Shade or equivalent |
| 142 | M&L Earthing with Galvanised Earth Plate Electrode 600x600x 6mm thick burried directlyin Ground (Earth Pit not less than 2.25 Metre below Ground Level) with Top edge of the Plate not less than 1.50 Metre below Ground Level, connected with Galvanised Earth Strip of size 25x6mm (upto 7.5m length) by means of Bolts, Nuts, Check Nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar including GI 40mm bore (dia) light grade Protection Pipe, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt, Magneisum Sulphate (1 : 1 : 0.5) in alternate layers of not exc 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50 mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, Funnel with GI Watering Pipe 20mm bore (dia) medium grade including necessary Excavation in any type of soil, Returning, Filling in and Removal of surplus Spoil disposal to out side MD land and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including taking down old unserviceable one, complete all as per specified and as directed. |
| 143 | Supply and fix not less than IP 65 Pole Mounted street lighting Junction Boxfor controling building security lights 160x240x120 mm made of Polycarbonate, supplied with 1 No. 6A Amp 10KA SP MCB, 1 No. 63A 4P FR Polyamide color coded RYBN Terminals Block, 1 No. each of Earth & Neutral Terminal mounted on 35mm DIN channel and fitted inside Enclosure alongwith Pole Mounting bracket, pole clamp & hardware made of Stainless Steel 304. The Junction Box enclosure Cover should have 2 nos Polycarbonate Hinges with SS 304 Hinge pin, for Cover not to detach from Base on opening and should be properly tightened to base with Polycarbonate screws having sealing gaskets of extruded silicon rubber complete all as specified and directed. |
| 144 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 corecomplete all as specified and directed. |
| 145 | Removing excavated materials not exceeding 50m distance and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified and directed. |
| 146 | Riddling Sand obtained from excavation for cable protection 8cm under the cable and 15cm above the cable in trench and get the thick layer of 18cm after ramming complete all as specified and directed. Note :- In case sufficient sand not obtained from excavation, the quoted rate is deemed to be inclusive for the required additional qty obtain from out side MD land as directed by the Engineer-in-Charge. |
| 147 | M&L Fly ash bricks using modular bricks as in cable protection cover including taking down existing bricks of any size complete all as specified and directed. |
| 148 | M&L for point wiring complete with 1.5 sqmm single core PVC insulated, unsheathed FRLS 1100 volts grade,FRLS cable and incl non metalic PVC Conduitwith accessories in drawing through wall/roof conceled etc incl modular terminal boxes fabricated with 1.6mm MS/GI sheet concealed to wallsetc and 1.5 sqmm PVC insulated, unsheathed copper conductor multistrandedcable 1100V grade as earth continuity conductor & connecting to common earth dolly all as specified for |
| 149 | One light/fan point controlled by one switch |
| 150 | All as per item No. 147 here in before but for One 3 pin socket out 5 ampon the indpboard |
| 151 | All as per Sl No 146 above but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently |
| 152 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed. |
| 153 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five starrated with brushless direct current motor (BLDC) |
| 154 | M&L for sub main wiring with PVC insulated unsheathed FRLS 1100 volts grade multi stranded copper conductor cable2 runs of 4 sqmm drawn through in and incl suitable size PVC conduit and all accessories fixed to wall/floors along with 4 sqmm PVC insulated unsheathed copper conductor multi stranded cable 1100V grade as earth continuity conductor and connected to common earth dolly complete all as specified and as directed. |
| 155 | Supply and fixing ceiling fans clamps to roof for fixing of ceiling fans complete all as specified and directed by Engr-in-Charge. |
AI Tender Summary
Tender Timeline
Jan 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender