Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Demolition of brick work or stone / boulder masonry built in CM including all quoins, arches, pillars, etc but excludingashlar, facing, dressedstone work and pre-cast concrete articles complete all as specified and as directed by Engineer-in-Charge |
| 2 | M&L for Dismantling Framed Truss Complete all as specified and as directed. (n. exc 10 m) |
| 3 | Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 4 | Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and as directed |
| 5 | Returning, filling in, incl spreading, leveling, watering and well ramming in layers n exc 25 cm as in soft/loose soil complete all as specified and as directed. |
| 6 | Removal of surplus soil to a distance not exceeding 50 mtr away & depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-charge. |
| 7 | M&L for plain cement concrete 1:4:8 (Nominal mix) using 40 mm graded stone aggregate as in foundation and mass concreteetc complete all as specified and directed. |
| 8 | M&L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface |
| 9 | M&L for brickwork with subclass \"B\" Bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed by Engr-in-charge. |
| 10 | Demolition of cement concrete ,un-reinforced in ground floors and paving any thickness, below or above ground level complete all as specified and as directed. |
| 11 | M&L for 100 mm thick cement concrete type C- 2,1:3:6 (40mm graded aggregate)as in sub-base complete all as specified and as directed. |
| 12 | M&L 15 mm thick rendering in cement mortar (1:6) on brick or concrete surfaces finished even and smooth without using extra cementcomplete all as specified anddirected. |
| 13 | M&L rendering 15 mm thick cement plaster on fair face of brick work or concrete surface in CM (1:4) & water proofing compound mixed @ 3% or as per manufacturer instruction complete all as specified and as directed.( Note -W.P.C. shall be measured and paid separately . ) |
| 14 | Supply only integral water proofing compound all as specified and as directed. |
| 15 | M & Lfor Glazed ceramic Coloured tiles in vertical surface 300x 450x 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 15mm thick cement mortar 1:4 rendering as specified and as directed. Make:- Kazaria/Somany or equivalent. |
| 16 | S&F Non skid Ceramic tiles 7 to 8 mm thick(square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick cement mortar 1:4 bedding, all as specified and as direccted,Make:- Kazaria/Somany or equivalent. |
| 17 | M&L for non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6), complete all as specified & directed. |
| 18 | M&L for plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete etc complete all as specified and directed. |
| 19 | S&F rolled mild steel Fe-410-W (Gde-E-250) quality-B as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and as directed by Engineer-in-Charge. |
| 20 | Dismantling timber scantlings 40 Sqcm and over in section, in any position unframed work complete all as specified anddirected . |
| 21 | M&L for 2nd class hardwood clean sawn as in door frame, scantling fixed to timber frame etc complete, all as specified anddirected . |
| 22 | M&L for Mild steel work in tubular/rectangular/square trusses including special shaped washers, base plate etc complete using ERW or induction butt welded tubesconforming to IS-1161-1979 grade St-240, fastening in wall with nut & bolt complete all as specified anddirected by Engineer-in-Charge. Note :- The cost of nuts, bolts & washers for jointing to the members of trusses shall be deemed to beincluded in the quoted unit rate by tenderer . Nothing extra shall be admissible on this account. |
| 23 | S&F rolled mild steel Fe-410-W (Gde-E-250) quality-B as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed by Engineer-in-Charge. |
| 24 | Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in Soft/ loose soil and removing surplus soil to a distance n.exc 50m & making good surface complete all as specified and as directed by Engineer-in-Charge. |
| 25 | Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc complete all as specified |
| 26 | S&F for Galvalume zinc coated GI based corrugated sheet shall be 0.50mm thick (total coated thickness), 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers.all as specified and directed by Engineer-in-Charge |
| 27 | S&F for Galvalume zinc coated GI based plain sheet shall be 0.50mm thick (total coated thickness), 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. all as specified and directed.by Engineer-in-Charge |
| 28 | S&F in repairs 0.71 mm thick plain aluminium sheeting alloy 31000 H4 in stepped flashing (measured as the minimum rectangle from which the pieces can be cut) fitted in wall cladding, as valley gutter , steel gates etc. cut to size, holes punched including fixing to MS clamps with necessary bolts and nuts as directed. |
| 29 | M&L for applying3mm thick wall careputty onwall and ceiling to provide smooth even surface complete all as specified and directed by Engr-in-charge. |
| 30 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets/ACP board, any thickness, any description including cover fillets |
| 31 | M& L Nonasbestos fibre cement building boards size605 x 605mmfixed or laid/ inserted to timber/GI/Aluminium snap gridframework for false ceilingwith screws complete all as specified and as directed by Engineer-in-Charge |
| 32 | S&F 18-20 mm thick granite slab cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pavement to match the shade of granite stone incl grinding and polishing overand including 20mm screed bed in CM(1:6) completed all as directed. |
| 33 | M&L for Weather boarding of 2nd class softwood 30 cm wide, clean sawn, plain, 20mm thick or feather edged15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed. |
| 34 | S&F Exterior ACP (Alumiumn composite panel) sheet thickness 3-5 mm of any desired colour with PVDF (Polyvinylidene fluoride) coated included all necessary fitting complete as and directed by Engrin-charge |
| 35 | S&F 30mm width of flap continuous (piano) hinges, mild steel, bright finish complete |
| 36 | S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, brass polished complete all as specified anddirected. |
| 37 | S&F in repair 75mmHasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified anddirected. |
| 38 | S&F for 18/19 mm thick Particle board with one side veneer finished for cub boards, insulation purposes , fixed with screws to wooden/aluminium framework complete all as specified and directed. |
| 39 | Taking down chowkhats or frame (without taking off shutter from the frame)not exceeding 1.5 Square Metre each, removing from the site including cutting holes required fortaking out existing hold fast etc. complete all as specified and as directed. |
| 40 | Taking down chowkhats or frame (without taking off shutter from the frame) exceeding 1.5 Square Metre and not exceeding 4 Square Metre each completeall as specified and directed. |
| 41 | S&F aluminium anodised powder coated frame of standard section for doors, windows, ventilators of any colour as approved with one or more rebates including joining cleat,etc for fixing etc. complete all as specified & as directed. |
| 42 | S&F aluminium anodised powder coated door shutters, with top rail of size 47.62mm x 44.45mm, intermediate rail 100mm x 44.5mm, bottom rail 88mm x 44.5mm, style size 44.45mm x 47.52mm, including necessary joining cleats, glazing clips, rubber neoprene packing/ rubber gasket, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc.complete all as specified & directed. . |
| 43 | S&F aluminium anodised powder coated window and ventilator shutters, sliding type with size of sliding shutter style39mm x 20mm, top rail size 39mm x 20mm and bottom rail size 41mm x 20mm,joining cleats, glazing clips, rubber packing/rubber gaskets, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) ,complete, all as specified & directed. |
| 44 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. |
| 45 | S&F 5.5mm thick sheet glass, ordinary quality, glazing with oil putty or with wooden beads or aluminium , area exceeding 0.50 Sqm but not exceeding 1.0 Sqm each pane with and includingsolar control film 25 micron reflective type(greatersun control or equivalent) complete all as specified and directed. |
| 46 | S&F for 12mm thick Particle board for insulation purposes , fixed with screws to aluminium framework complete all as specified and directed. |
| 47 | S&F 4 mm thick obscured or frosted sheet glass of ordinary quality and glazing with oil putty or wooden beading to wooden frame or steel frame in square n. exc 0.5 Sqmin each pane complete all asspecified and as directed by Engineer-in-Charge. |
| 48 | S&F 4 mm thick sheet glass of ordinary quality and glazing with oil putty or wooden beading to wooden frame or steel frame or aluminium in square not exc 0.5 Sqmin each pane solar control film 25 micron reflective type(greatersun control or equivalent) complete all as specified and directed. |
| 49 | S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or screws to aluminium skeleton door panel completeall as specified and directed. |
| 50 | S&Ffor 30 mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both face is covered with decorative face veneer with lipping/frame to match sides and fitted to chowkhats complete all as specified anddirected. |
| 51 | S&F Door closer Aluminium (Die cast) body hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg complete all as specified and as directed. |
| 52 | S & F for Aluminium Mortice lock vertical type size 75 mm 04 levers complete all as specified and as directed. |
| 53 | S&F solid PVC door frame of size50mm x 47mm made out of 5 mm wood grain printedPVC sheetreinforced with MS square tube and edges will be painted to match will printed sheet fixed in opening as per specification & drawings complete all as specified and as directed complete all as specified and as directed. |
| 54 | S& F of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed. |
| 55 | S&F in repairs sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polyethylene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM (1:3) or PCC (1:2:4) type B0, complete, including taking down old unserviceable sink complete all as specified and directed. |
| 56 | Taking up or down steel tubing 15 mm bore and connections including cleaning for refixing or removing from site. |
| 57 | Taking up or down steel tubing 20 mm bore and connections including cleaning for refixing or removing from site. |
| 58 | Supplying and laying of 16 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 with all fittings and fixed complete on walls and ceilings or laid in floors all as specified and directed. |
| 59 | Supplying and laying of 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 with all fittings and fixed complete on walls and ceilings or laid in floors all as specified and directed. |
| 60 | S &F of Brass Elbow 16/20 mm bore complete all as specified |
| 61 | S &F of Brass Elbow (3/4 X ½) 20 mm bore complete all as specified |
| 62 | S &F of Brass Tee 16/20 mm bore complete all as specified |
| 63 | S &F of 20 mm bore BALL VALVE / gate valve complete all as specified |
| 64 | S&Fin repairs Angular cock ( 15 mm dia of bore), cast copper alloy, fancy type Chromium plated screwed down, one way/two wayhigh pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed as Engr-in-charge. |
| 65 | S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed as Engr-in-charge. |
| 66 | S&F in repairs Bib taps (15mm dia of bore), cast copper alloy with capstan heads, fancy type chromium plated ,screwed down, screwed for iron pipe or for brass ferrule and fixed including necessary fittings complete all as specified and directed by Engr-in-charge. |
| 67 | S & F in repairs hand shower (health faucet) ABS body mile steel chromium plated for 15mm dia, 1.25meter long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 68 | S & F Decorative designer looking mirror of selected quality 5 mm thick mounted on 2mm thick laminated PVC sheet with necessary fixing arrangement complete as directed. |
| 69 | Dismantling CI/AC/PVC (SWR) pipes & fittings of any description fixed to wall/laid in trenches including making good disturbed portion of wall floor etc. |
| 70 | S & F 110 mm dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints , laid in trenches or in floorcomplete all as specified and directed by Engineer-in Charge. |
| 71 | S & F in repairs 110 mm dia PVC (SWR) bends any radius, with access door complete all as specified and directed by Engineer-in Charge. |
| 72 | S & F in repairs 110 mm dia PVC (SWR) bends any radius, without access door complete all as specified and directed by Engineer-in Charge. |
| 73 | S & F in repairs PVC (SWR) junction single (single T) equal or unequal 110mm bore, withoutaccess doorcomplete all as specified and directed by Engr-in-charge. |
| 74 | S & F in repairs PVC (SWR) junction single (single T) equal or unequal 110mm bore, withaccess doorcomplete all as specified and directed by Engr-in-charge. |
| 75 | Taking down floor trap/nahani trap of any description any size and making good to disturbed portion with cement concrete type B-1 1:2:4 with water proofing compound complete all as specified and directed. |
| 76 | M & L 75mm outlet dia PVC(SWR)floor trap, plainwith grating including jointing with solvent cementall as specified and directed. |
| 77 | S & F 75 mm dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints , laid in trenches or in floorcomplete all as specified and directed by Engineer-in Charge. |
| 78 | S & F in repairs 75 mm dia PVC (SWR) bends any radius, with access door complete all as specified and directed by Engineer-in Charge. |
| 79 | S & F in repairs 75 mm dia PVC (SWR) bends any radius, without access door complete all as specified and directed by Engineer-in Charge. |
| 80 | M&L for concrete bed to drain pipes for 110mm bore SGSW/PVC SWR drain pipe in cm 1:4:8 type D-2, using 40 mm graded stone aggregate including packing under and haunching against the sides of pipesin foul smell condition complete all as specified and as directed. |
| 81 | M&L for 18-20mm thick Granite (of any type) machine cut, in window cills, bathroom platforms, shelf platforms etc. bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 12 mm thick screed bed in CM 1:6 and polishing complete all as specified and directed by Engr-in-charge. |
| 82 | M&L for 18 - 20mm thick Granite (of any type) machine cut, in vertical surfaces bedded and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 12 mm thick screed bed in CM 1:6 and polishing complete all as specified and directed by Engr-in-charge. |
| 83 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situationscomplete all as directed by Engr-in-Charge. |
| 84 | S&F 12 mm thick Toughned glass as in hinged doors, partitions ,automatic doors and similar work including cutting to shape, drilling holes, etching includingglass is ground or obscured or frosted, on one side required complete all as specified. |
| 85 | Supply & fixing and providing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of floor or the side of waist slab with suitable arrangement. Complete all as specified and directed. |
| 86 | Grinding, polishing and rounding off edges of glass, any type exc 4 but not exc 8mm thickand securing glass in metal frame complete all as specified and directed. |
| 87 | M& L for 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) with integral WPC as per manufacturer instruction complete all as specified and directed by Engr-in-charge. |
| 88 | M&L for applying two coat of cement based paint to newly plastered surface of wall over a coat of primer including preparation complete all as specified and as directed. |
| 89 | M&L for complete removal of existing treatment using mechanical means and preparing old plastered surface of wall complete all as specified and directed. |
| 90 | M&L for applying two coats of Oil Bound Distemper to old plastered surface of wall over a coat of chalk whiting primer over 3 mm wall care putty complete all as specified and directed. |
| 91 | M&L for applying two coat of cement based paint to old plastered surface of wall over a coat of primer complete all as specified and as directed. |
| 92 | M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surface complete. |
| 93 | M&L for preparation of newly plastered wall surfaces and applying two coats of Oil Bound Distemper over a coat of alkali resistant primer applied over 1 to 2 mm thick wall putty complete all as specified and directed by Engineer -in-Charge. |
| 94 | M&Lforcomplete removal of existing surface and applying three coat of white wash to old decorated (white washed) surfaces of wallcomplete all as specified and directed by Engineer -in-Charge. |
| 95 | S&F in repairs brass centre hole basin mixer with quatre turn fittings for mixing hot and cold water (15mm dia of bore), cast copper alloy, with capstan heads, fancy type chromium piated (robotic electroplating for everlasting lustrous shine), screwed down high pressure, with 2 water volume adjustment knobs one both side to control the flow of temperature, screwed for iron pipe and fixed brass chromium Concealed angle stop cock with wall flange of 15mm dia capstan head including necessary fittings complete ali specified and directed by Engr-in-charge Make Prayag Cat No. 6550 / P6650 / P6850 /Hindware model no. F920034CP / Cera model no. F2002461 or equivalent |
| 96 | S & F oval type counter basinsize 430x295x130 - 595x420x200 including waste coupling etc complete as specified and directed by Engr-in-Charge. Make asian paints wm-41-x / prayag 4706 or eq model of make specified |
| 97 | S&F in repair vitreous china floor mounted coupled closet (Pedestal pattern) white including low level vitreous china valveless syphonic action type flushing cistern with inlet ball valve float,push button, flush pipe incl bracket, P/S trap, PVC coloured seat cover and connecting fittingsincluding taking down existing water closet complete all as specified and directed.(Make :CERA, Model : CALIBRE / ASIAN PAINTS , Model: PRIMUS / JAQUAR, Model: CONTINENTAL / HINDWARE, Model: ALPHA S 220 / PARRYWARE, Model: INDUS) |
| 98 | S&F in repairs toilet paper holder, surface type with flap incl taking down existing holder complete all as specified and directed. (Make : JAQUAR, Cat No : CAN-1153N / CERA, Cat No: F5007110 / PRAYAG, Cat No: CPA-45 BA-38 / ESS ESS, Cat No: AC-506 / HINDWARE, Cat No: F880003) |
| 99 | S&F in repairs vitreous china urinal, full stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polyethylene of low or high density or PVC 32mm dia, complete all as specified & directed. make jaguar cat no. URS-WHT- 13253N , PRS-073 (with all necessary fittings required like flush valve connection pipe spreaders |
| 100 | S&F in repair 15mm bore chromium plated two way bib cock with flange, fancy type complete all as specified and as directed.(Make : Ess Ess, Cat No: C-203 / JAQUAR, Cat No: CON-041KN/ PARRYWARE, Cat No: G1434A1/ CERA, Model : OCEAN / PRAYAG, Cat No: 9212/HINDWARE, CAT No: F330004CP) |
| 101 | M&L for Providing, cement concrete 1:2:4 Type B-1 (using 20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed. |
| 102 | S&F inLiquid soap container of PTMT / cp fixed with and including Chromium plated brass screws and wooden/plastic cleats Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified & directed |
| 103 | M&L for 10 mm dia and over cut to length bent to shape required incl cranking, bending, binding with and incl mild steel wire (annealed) not less than 0.9 mm and necessary welding to reinforcement complete all as specified and as directed. |
| 104 | All as per item Sl No. 103 above, but 5 mm dia & over up to & Incl 10 mm dia in Stirrup, spacer & binder etc. complete all as specified and directed. |
| 105 | M&L forFormwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, coping beam etc. also splays between floors and beams, etc. for rough finished surface. |
| 106 | M&L for cement concrete type B1 1:2:4 20 mm aggregate in lintels upto & over1.5m clear span,cills,steps; seismic and other similar bands, plinth courses, string courses lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stonesbed plates, kerbs not provided for in Item 04028, water troughs and the like includingweathering,slightly rounded or chamfered angles and throating, as directed complete as specified and directed by Engr-in-Charge |
| 107 | S&F in repairs in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 600mm long completeall as specified and directed. Note: make parryware/prayag or equivalent. |
| 108 | S&F of Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of26 mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. |
| 109 | Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) |
| 110 | M&L for Vitrified Ceramic tiles, Dark shade/Double Charged/Ultra Charged,7 to 10 mm thick(square orrectangular ) polished area of each tiles exc 0.36 sqm but n exc 0.42 sqm laid as in floors, setting and jointed with cement slurry over & including 15mm thick bedding of layer of cement sand mortar (1:6) and pointed with coloured cement to match with surfaces of tiles complete all as specified and as directed. |
| 111 | M&Lfor preparation of new or untreated painted wood andwooden based surfaces of any description not other wise described over 10 centimetre width or girth and applying two coats of synthetic enamel paintover a coat ofpink primer, complete all as specified anddirected. |
| 112 | M&Lfor preparation of new or previously untreated steel and iron surfaces of any description not other wise described over 10 centimetre width or girth over a coat of red oxide primer, complete all as specified anddirected . |
| 113 | M&L for preparation of old painted wood andwooden based surfaces of any description not other wise described over 10 centimetre width or girth and applying one coat of synthetic enamel paint complete all as specified anddirected. |
| 114 | M&L for preparation of old painted steel and steel based surfaces of any description not other wise described over 10 centimetre width or girth and applying one coat of synthetic enamel paint complete all as specified anddirected. |
| 115 | M&L for Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated withCreosote oil complete all as specified anddirected. |
| 116 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using platevibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; |
| 117 | M&L 75 mm thick P.C.Ctype C-2, 1:3:6 using 40mm graded aggregate as in Sub-floor, sub base etc , finishing the surfaces of concrete ( without using extra cement) even and rough to receive the topping layer complete all as directed. |
| 118 | S&F of 125mm Long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed complete all as specified anddirected |
| 119 | S&F of Extruded brass handles,fabricated type polished handle, , 150 mm size complete all as specified and as directed. |
| 120 | S&F of 200 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed. |
| 121 | S&F of250 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixedcomplete all as specified and as directed. |
| 122 | S&F Mild Steel Butt hinges, heavy weight, cold rolled, of size 100 mm complete all as specified anddirected. |
| 123 | S&F 150 mm long mild steel barreltower bolt, stove enamelled black with bright bolt complete all as specified anddirected. |
| 124 | S&F in repairs Aluminium handle, cast type anodized size of handle 150 mm complete all as specified and as directed. |
| 125 | Dismantling ofStone slabs and tiles of any description or thickness Laidbeddedand pointed in any mortar infloors, aprons etc. complete all as specified and as directed. |
| 126 | Demolition R CC of any description and any position not otherwise specifically provided |
| 127 | Dismantling wrought iron or mild steel work of any description. |
| 128 | Dismantlingsteel barbed wire ofany description fixed to any type of fencing posts |
| 129 | Dismantling concertina wire fencing of any description fixed to any type of fencing posts complete all as specified and directed. |
| 130 | Removing building materials etc. to a distance of 500m or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination |
| 131 | M&L Reinforced cement concrete (design mix) foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc basement slabs, under reamed piles and mass concrete in concrete grade M-25 complete all as specified and as directed. |
| 132 | M&L Reinforced cement concrete (design mix) in columns, pillars, piers, posts and struts in concrete grade M-25 complete all as specified and as directed. |
| 133 | M & L for RCC M-25 design mix using 20 mm graded aggregate for Beams, cantilevers, bressummers, Rcc band lintels over 1.5m span complete all as specified and directed |
| 134 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter with rough finished surfaces. complete all as specified and directed |
| 135 | Formwork to sides of pillars, posts, struts, piers, column and stanchion complete all as specified and directed |
| 136 | M&L for rendering 15mm thick in cement mortar 1:4 on other than fair surfaces of brickwork or concrete surface finishingeven & smooth without using extra cement complete all as specified and as directed. |
| 137 | S&F hand rails, half round or other stock section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290,complete all as specified and directed |
| 138 | S&F Galvanised 2 strand steel barbs wire 2.24mm dia steel barbed wire with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolt etc as directed (Each line of wire is to be measured separately) |
| 139 | M&L for preparation for new plaster surface andapplying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 140 | S&F in repairs super Razor punched barp tap(SRPBT) aluminium based helix coil with sand including necessary GI fixing clips for securing complete all as specified and directed with following specification :-(i) Dia of coil (when unstretched) - 610mm (ii) Nos of circles-51 turns per coil (iii) weight of each coil with hessian pack- 8.50Kg (iv) coverage per coil- 8RM (v) central core wire- made from 2.50mm dia GI-H.T.S.S wire asper IS-4454 galvanised as per IS 2629 (vi) Razor punched strip - Razor punched tape i steel comprising of aluminium base with Zinc alloy coating @ 150gm/sqm conforming to ASTM A792/A-792/A-792Mwith additional primer treatment of Epoxy/polyurethane & Finsal paint Top coat of caulfield green shade (BSL 139)by Hot dipping process. |
| 141 | S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework or water tanks and similar work con- formingcomplete, all as directed by Engr-in-charge. |
| 142 | Supply and spreading dry sand of approved quality for cushioning of UG cable laid in trenches 8 cm deep before laying the cable and 15 cm thick after laying & stretching the cable complete all as specified and directed.(NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only shall be Measured and Paid for). |
| 143 | M & L brick protection with old size sub class ‘B’brick for PVC underground cable protection in trench with width equal to length of brick laid dry and flat joining each other with gap between adjacent brick not exceeding 10mm gap over LT under ground cable all as specified and directed. |
| 144 | M&L for tubes 40 mm bore light grade galvanized with all fittings laid in trenches/ wall/ pole through MS flat (25X3 mm), nut, bolt & washers [ where ever reqd ] of proper sizes for protection cables complete all as specified and directed. Make- Nezone/ Bansal/ Jindal |
| 145 | S&L in repair of UG cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor,1100 Volts grade, cross section area incl taking down of size16 sq mm 4 core complete all as directed. |
| 146 | M&L steel tubular sewaged pole 9 mtr long complete with MS bas plate,finial taper plug nut bolts, screws as specified type 410SP-31 as per relevant IS specification including two coat of aluminium paint over a coat of red oxide primer including taking down old unserviceable and removing from site complete all as directed by Engr-in-charge(earth work/excavation PCC shall be measured and paid seprately under relevant item of schedule). |
| 147 | M&L for fixing the FRP cable junction boxes of size 155 x 210 x 92 mm,with five way connector (Heavy duty) terminals for 10 - 16 sq mm, 1100Vcable, IP 66, weather proof, outdoor installation type with threaded cable glands & pole mounting brackets with one SP MCB 6 Amps etc complete all as specified & directed. Make- Hensel / OBO |
| 148 | M &L 2.5 Sqmm, 3 Core Black PVC Insulated Single solid Aluminium conductor round service cable 1100Vfor connection from loop /junction box to street light / security light complete all as specified and directed. |
| 149 | M&L for tubes 15 mm bore light grade galvanized with all fittings laid in trenches/ wall/ pole through MS flat (25X3 mm), nut, bolt & washers [ where ever reqd ] of proper sizes for protection cables complete all as specified and directed. Make- Nezone/ Bansal/ Jindal |
| 150 | M&L for hot dip galvanised (as perBS EN ISO 1461 1991) brackets of 40 mm dia (medium grade), 1.5 m long for fixing LED type street light luminaires, fixing it to pole through MS Clamp, nut, bolt & washers incl taking down old one complete all as specified and directed. Note:-i) Any welding works related to bracket should be carried out at the factory premises of the manufacturers Make- NTL/ Nezone/ Jindal/ Tata |
| 151 | Supply and fixing LED street light fitting 90 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. |
| 152 | Supply and fix timer switch astro type suitable for outdoor application (Having longitude and latitude of Indian cities in memory) 250 V single phase of Max load capacity 12 KW rating with contactor rating 65/TP and MCB rating 63/TPNfitted inside steel enclosure confirms to IS/IEC 60947-4-1 with IP54 protection and H class insulation. Make- Havells, HSN Code-8537,SAP Code-IHXTS0912A or eq model of make specified |
| 153 | M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanizediron or steel all as shown in electrical plate No.5 of SSR Part-I (2009) including filling of charcoal dust , common salt all around Earth plate upto 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40mm thickRCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced withsuitable handle and angle iron frameand necessary excavation and earth work in any type of soil etc. complete all asspecifiedand as directed includingtesting on completion. (Note: The rate quoted shall inclusive of GI wire 4 mm dia with GI pipe protection 15 mm, light grade up to 7.5 m) |
| 154 | M&L forPCC as in foundation or any other works type C1 (1:3:6) (20mm graded aggregate) all as specified and directed. Note:- Any form work required for PCC works are deemed to be included in this rate. |
| 155 | Material and labour for Point wiring with 1.5 Sqmm FR PVC insulated and sheathed multi stranded (FRLSH) copper conductor cable inand incl rigid PVC conduit concealed with sunk cast iron/pressed steel terminal boxes ofadequate size with suitable thickness hylum laminated sheet , coverofadequate size for one light or one fancontrolledby one switch incl 1.5 Sqmm (FRLSH) PVC insulated andunsheathed multi stranded copper conductor cable as earth wire (green colour) to common earth dolly complete all as specified and directed by Engr-in-charge. Note:- (a) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc(b) On RCC roof ceiling PVC conduit shall be provided on surfaces for fan etc with proper fixing clips all as directed |
| 156 | All as per serial item No 155 here in before but for one 3 pin 5 Amp socket outlet on independent board. |
| 157 | All as per serial item No 155 here in before but for one 3 pin 5 Amp socket outlet on same board. |
| 158 | Material and labour for Point wiring with 4.0 sqmm FR PVC insulated and sheathed multi stranded (FRLSH) copper conductor cable drawn in and including rigid PVC concealed conduit medium grade of suitable size with and including Metal flush Box of adequate size with suitable thickness plastic laminated sheet, cover for one 3 pin socket outlet 15 Amp on independent board including continuous 4.0 sqmm copper conductor cable (FRLSH) (multistranded) PVC insulated and unsheathed Cable as earth wire to common earth dolly, complete all as specified and directed by Engr-in-charge |
| 159 | Material and labour for ceiling rose surface bakelitetwo to three terminal isolated body fixed on PVC round block, 6A, Pilot 2 Plate, complete all as specified and directed by Engr-in-charge |
| 160 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. |
| 161 | Supply and fix of MCCB TPN DB 4 waydouble door,IP 43 protection,Glazed door, isolated neutral bar,insulated bus bar assembly,mechanical strength of IK09, complete all as specified and directed. |
| 162 | Supply and fix of MCCB 63 Amps ,4Pole,16 Ka,415 volts completeall as specified and directed. |
| 163 | S&F On-Load Manual Change Over Switch (in sheet steel enclosure) 63 Amps 415 Volts,4 pole after disconnecting all electrical connection incl. taking down old unsv one complete all as specified and directed. Make - L&T/ Siemens/ABB |
| 164 | Supply and fix in repairs of DB 8 way MCB SPN double door, glazed type, IP 43 protection,Glazed door, isolated neutral bar,insulated bus bar assembly,mechanical strength of IK09, complete all as specified and directed. Make- Legrand / Indo asian / Havells or its equivalent in specified makes in CA. |
| 165 | Supply & fix in repair of MCBs single pole (SPN) 6 to 32 Amps with 10 KA breaking capacity of \"C\" series in distribution boards confirming to IS/IEC 60898-1 (ISI marked) complete all as specified and directed. |
| 166 | Supply & fix in repair of MCBs single pole (SP) 6 to 32 Amps with 10 KA breaking capacity of \"C\" series in distribution boards confirming to IS/IEC 60898-1 (ISI marked) complete all as specified and directed. |
| 167 | S&F Modular Plate 2 module White cover plate with frame, complete all as specified and directed by Engr-in-charge |
| 168 | S&F Modular Plate 3 module White cover plate with frame, complete all as specified and directed by Engr-in-charge |
| 169 | S&F Modular Plate 6 module White cover plate with frame, complete all as specified and directed by Engr-in-charge |
| 170 | S&F Modular Plate 12 module White cover plate with frame, complete all as specified and directed by Engr-in-charge |
| 171 | M&L for Modular type 5 step Fan Regulator - 2 M oro white, complete all as specified and directed by Engr-in-charge |
| 172 | M&L for Modular switch 6 A One way switch white, complete all as specified and directed by Engr-in-charge |
| 173 | M&L for Modular 6 A, 5 pin socket, complete all as specified and directed by Engr-in-charge |
| 174 | M&L for Modular 6 A/16 A socket, complete all as specified and directed by Engr-in-charge |
| 175 | M&L for Modular 16 Amp One way switch white, complete all as specified and directed by Engr-in-charge |
| 176 | M&L for Dummy Plate - 1 Module Oro (White), complete all as specified and directed by Engr-in-charge |
| 177 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m. |
| 178 | S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. |
| 179 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 4 core |
| 180 | S&F Sheet metal enclosure having single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp. |
| 181 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make:-Philips/Havells/Wipro |
| 182 | Supply and fixing Recessed Mounted POP-UP LED Downlight with 355° rotation and 90° tilt for Directional adjustment,High efficiency COB used with better product efficacy 95 LPW. THD<10% with fixture size Fixture size: Ø 75 mm, length 100mm, width 100mm & height 112 mm and Cut-out: 63x63mm for 1x10W light. Make- Havells, item description: UNECOPOPUPR10WLED830S24WHT one eq model of make specified |
| 183 | S&F in Replacement of existing sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area4.0 Sqmm drawing into and including PVC casing and caping of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 4.0 Sqmm as a earth continuity conductor(green colour) in and including in non metallic rigid PVC conduit, including cutting chases in brick wall, replastering and making good to match the existing specifications complete all as specified and directed by Engineer-in-Charge. Make: KEI/Havells/Anchor/polycab Note :- (i)Rates are deemed to be included chases of sinking for boxes cutting and making holes in wall/floor for passing in or through conduit (ii)Two run of4.00 sqmm single core (FRLS) PVC insulated copper conductor cable one run of 4.0 sqmm copper conductor cable (FRLS)as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
