Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed. |
| 2 | Excavating in trenches in hard/dense soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and directed |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed |
| 4 | Removing excavated soil exc. 1.5km but n exc. 5 km and depositing where directed at a level n.exc 1.5m above the starting point, complete all as specified and directed. |
| 5 | M& L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed. |
| 6 | M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured),complete all as specified and directed. |
| 7 | M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface with ATT,complete all as specified and directed. |
| 8 | M&L cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base / sub-floor below footing or foundation, plinth beam complete all as specified and directed. |
| 9 | Demolition of RCC of any descriptionand in any position not other wisespecially provided for (reinforcement cut as required to facilitate demolition ) complete all as specified & directed. |
| 10 | M&L for providing Reinforced Cement Concrete (1:1.5:3) type B1 using 20 mm graded stone aggregates as infoundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 11 | M&L for providing Reinforced Cement Concrete (1:1.5:3) type B1 using 20 mm graded aggregate as inColumns, pillars, piers, posts and struts etc and like complete all as specified and directed. |
| 12 | M&L for providing Reinforced Cement Concrete (1:1.5:3) type B1 using 20 mm graded stone aggregates as in roof beams, lintel beam, slabs supported on walls, roofs, landings balconies canopies, deck slabs and in shelves balconies canopies etc and like complete all as specified and directed. |
| 13 | M&L for providing Reinforced Cement Concrete (1:1.5:3) type B1 using 20 mm graded stone aggregates as in chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings complete all as specified and directed. |
| 14 | Formwork to sides of concrete foundations, footings, columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter complete all as specified and directed. |
| 15 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed. |
| 16 | Formwork to soffits of suspended slab such as roof slabs, floor slabs, landings, beams and similar work not exc 200 mm thick horizontal or sloping, rough finished flat surfaces complete all as specified and directed. |
| 17 | Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. |
| 18 | Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. |
| 19 | S&F mild steel TMT bars 10mm dia and over, cut to length & bent to shape required including cranking, bending spirally for hoping for column, stirrups of beams and columns hooking ends & binding with and including mild steel wire not less than on 0.9mm dia or securing with clips complete all as specified and directed. |
| 20 | S&F mild steel TMT bars 6 to 8 mm dia as in stirrups, spacers and binders cut to length & bent to shape required including cranking, bending spirally for hoping for column, stirrups of beams and columns hooking ends & binding with and including mild steel wire not less than on 0.9mm dia or securing with clips complete all as specified and directed. |
| 21 | M&L for PCC(1:3:6) type C2 using 20mm graded stone aggregates as in plinth protectionof avg 75mm thick and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 22 | Demolition of brick or stone masonry built in cement mortar incl all quoins, arches, pillar etc. complete all as specified and directed as inopening complete all as specified and directed. |
| 23 | M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 24 | Description all as per srl item no 23 here in before but except bricks complete all as specified and directed. |
| 25 | M&L for 25 mm thick Cement concrete (1:2:4) type B0 using 12.50mm graded stone aggregate over sub base concrete floors, surface fair finished and even and rough to receive floor finishes,complete all as specified and directed.. |
| 26 | Dismantling boarding, any description any size , fixed in any position with screws complete all as specified . |
| 27 | M & L for 18 mm thick Celuka Ply of density 600kg/cum of plain colour Sheet for kitchen cabinets sides, top, bottoms and shelves inside the cabinet, with all fittings/ fixtures hinges,screws, nut, bolts, adhesives, etc complete all as specified and directed. |
| 28 | M & L for 18 mm thick Celuka Ply of density 600kg/cum one side prelam/Rigidlam (Colour/Shade as approved by GE) and other side plain white colour to make kitchen cabinet shutters / drawer,with all fittings/ fixtures hinges,screws, nut, bolts, adhesives, etc complete all as specified and directed. |
| 29 | M & L for ball bearing drawer channel telescopic type (500mm) Full Extention Load of load bearing capacity 45 Kg, with all fittings/ fixtures hinges,screws, nut, bolts, adhesives, etc including taking down oldcomplete all as specified and directed.Make: Hettich / Godrej/ EbcoNote : Each pair means 2 nos of telescopic channel, one piece fixed on left side and another piece fixed on right side. |
| 30 | M & L for CP Stainless Steel (SS 304) Wire basket two shelf pull out (bottle rack) of size 150 x 485 x 430 mm ,with all fittings/ fixtures hinges,screws, nut, bolts, adhesives,etc including taking down old basket,complete all as specified and directed. Make: Hettich / Godrej/ Ebco. |
| 31 | M & L for CP Stainless Steel (SS 304) Wire basket (Cuttlery Box ) size 420x 485x 100mm, with all fittings/ fixtures hinges,screws, nut, bolts, adhesives, etc including taking down old basketcomplete all as specified and directed.Make: Hettich / Godrej/ Ebco |
| 32 | M & L for CP Stainless Steel (SS 304) Wire basket (Grain Trolly ) size 425 x 495x 350 mm, with all fittings/ fixtures hinges,screws, nut, bolts, adhesives,etc including taking down oldcomplete all as specified and directed.Make: Hettich / Godrej/ Ebco |
| 33 | M & L for CP Stainless Steel (SS 304) Wire basket (Plate rack) size 420x 485x 150mm , with all fittings/ fixtures hinges,screws, nut, bolts, adhesives,etc including taking down old,complete all as specified and directed.Make: Hettich / Godrej/ Ebco |
| 34 | M & L for CP Stainless Steel (SS 304) Wire basket (Cup and Soucer rack ) size 420x 485x 100mm, with all fittings/ fixtures hinges,screws, nut, bolts, adhesives, etc including taking down oldcomplete all as specified and directed.Make: Hettich / Godrej/ Ebco |
| 35 | M & L for CP stainless Steel (SS304) plain Wire basket of size 420x485x100 mm , with all fittings/ fixtures hinges,screws, nut, bolts, adhesives, etc including taking down oldcomplete all as specified and directed.Make: Hettich / Godrej/ Ebco |
| 36 | M & L for stainless Steel (SS304) plain Wire basket of size 420x485x150 mm , with all fittings/ fixtures hinges,screws, nut, bolts, adhesives, etc including taking down oldcomplete all as specified and directed.Make: Hettich / Godrej/ Ebco |
| 37 | M & L for CP stainless Steel (SS304) plain Wire basket of size 420x485x200 mm , with all fittings/ fixtures hinges,screws, nut, bolts, adhesives etc including taking down oldcomplete all as specified and directed.Make: Hettich / Godrej/ Ebco |
| 38 | Supply and fixingAuto closes clip on cabinet hinges (regular) for kitchen cabinet shutters Note : Each pair means one piece fixed on openable shutter and other piece fixed on fixed portion. |
| 39 | Supply and fixing Stainless Steel (SS 304) handles 100 mm size for Kitchen Cabinet Shutterscomplete all as specified and directed. |
| 40 | Taking down chowkhat or frame with shutter (without taking off shutters from the frames) not exc 1.5 Sqm each complete all as specified and directed. |
| 41 | Taking down chowkhat or frame with shutter (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4.0 sqm each complete all as specified and directed. |
| 42 | Taking down door shutter of any description exc 1.00 sqm but n. exc. 2.00 sqm each complete all as specified and directed. |
| 43 | Taking down wooden shutters of any description exc 1 sqm but n.exc 2 sqm each from chowkhat and re-fixing in same opening after re-securing or easing and adjusting including repair of hinge as required complete all as specified and directed. |
| 44 | S&F solid PVC door frame of size 50mm x 47mm made out 5mm both side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet re-inforced with MS square tube complete all as specified and directed. |
| 45 | M&L for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes 40mm x 20 mm for top and bottom rails MS frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottom rail both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges panelling of prelam solid PVC sheets 10mm thick to be filted in MSframe 40 x 20 mm welded, sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with the solvent cement complete all as specified and directed. |
| 46 | S&F 1.25 mm (thickness MS Sheet) Pressed steel frames of size 125mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified and directed. |
| 47 | S&F 1.25 mm(thickness MS Sheet) Pressed steel frames of size 105mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified and directed. |
| 48 | S&F 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (any number of panels) with panel of timber flat on both sides (feather edged) or of 12mm thick BWP Commercial plywood with commercial face veneers, supplied and fitted complete all as specified and directed. |
| 49 | Supply and fixing glazed and gauged skeleton factory made shutters35mm thick, 2nd class hard wood \"Hollock\"open rebated and prepared to receive glass, gauge etc (with sash bars) edges of framing plain chamfered or rounded fitted with cutand mitred beads for securing glass etcincl priming coat. The size of member of shutters as spfd in SSR Part-1 Section 8 clause 8.20 (b) incl kiln seasoned and chemically pressure treated, complete all as specified & directed. |
| 50 | S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, 100mm size, ISI marked, complete all as specified & directed. |
| 51 | Supply and fixing200mm size aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed. |
| 52 | Supply and fixing 150mm sizeExtruded aluminium alloy handles, fabricated type, anodised aluminium handles, complete all as specified and directed. |
| 53 | Supply and fixing 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed. |
| 54 | Supply& fixingas in repairfloor door stopper of aluminium alloy body and tongue, overall length of cover plate 140 mm anodised with hard drawn steel spring, fixed to door shutters,complete all as specified and directed. |
| 55 | Supply and fixing galvanised stainless steel wire cloth 0.36mm nominal dia of wire and width of aperture 1.40mm and fixed with tinned tacks or galvanised wire stapples/ screws in metal surrounds as required fixedcomplete all as specified and directed. |
| 56 | Supply and fixing in repairsgalvanised stainless steel wire cloth 0.36mm nominal dia of wire and width of aperture 1.40mm and fixed with tinned tacks or galvanised wire stapples/ screws in metal surrounds as required fixedcomplete all as specified and directed. |
| 57 | S&F factory made box type steel window 1.25mm thickERW hollow P section of each frame size 60mmx25mm including grill using 10 sqmm bar double rebated both guage andglass shutter comprised gaused glazed &Skelton shutterERW section 50mmx20mm & 1mm thick with two openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thickwith following fittings welded to the frame shutter :-i)Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window. ii)Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf.iii) MS tower bolt 150mm long 2 No per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 Nos per leaf vi) MS pintal hinges 12 x 75 mm- 2 Nos each leaf vii) 10 mm square guard bar @ 10 cm c/c viii) 25 x 3 mm flat iron for joint of both frame wiremesh & Glazed welded inner side and outer side of frame ix) 0.36 mm nominal dia of stainless steel wire mesh and average width of aperture 1.40 mm fixed in glazed/gazed skelton shutterof window(x)3mm thick sheet glass ordinary quality and with oil putty in square n exc 0.50 sqm in each pane fixed in glazed /guage skelton shutter of windowxi) Fabrication and fixing arrangements as per specificationincluding taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed.xii) Two coat of synthetic enamel paint over one shop coat of red oxide primer.Note: (i)The mode of measurement shall be only one for the set of two i.e wire mesh window and glass window at one location and nothing extra shall be measured on this account. |
| 58 | S & F mild steel box type ventilator fixed type with glazing bar with mesh & glassall as per item ser No 57 here in above complete all as specified and as directed. |
| 59 | S&F as in repair mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed. |
| 60 | M&L for machine cut Kota Stone slab as in flooring / landing/treadsof stairs , 20-25 mm thicklaid overand including 15mm thick cement screed bed in CM 1:4 , laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab and including rubbing and polishing and making grooves in treads ( as required ) complete all as specified and directed. |
| 61 | M&L for machine cut Kota Stone slab as in skirting/ risers of stairs , 20-25 mm thick overand including 10 mm thick rendering in CM 1:4 , laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab and including rubbing and polishing complete all as specified. |
| 62 | Dismantling of wall tilling, floor tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off premises complete all as specified . |
| 63 | M&L for glazed ceramic coloured wall tiles 450x300x7mm thick on vertical surfaces such as dados set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles over and including 10 mm thick backing coatin CM 1:4 complete all as directed by Engineer-in-Charge. |
| 64 | M&L non skid ceramiccoloured joint free tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.16 Sqm but not exceeding 0.38 Sqm in floors etc with design pattern set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles laid over and including 15mm thick screed bed in CM 1:6 & complete all as specified and directed. |
| 65 | M&L for vitrified light shade double charged ceramictiles9 mm thick polished,area of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchlaid over 15 mm thick screed bed in CM 1:6 complete all as directed by Engineer-in-Charge. |
| 66 | Description all as pe ser item No. 65 here in above but in skirtingover & including 10mm cement backing in CM 1:4 complete all as directed by Engr-in-Charge. |
| 67 | Dismantlingof brick tiles or terracing tiles or Pre-cast Cement concrete tiles single layer on roof, jointed and grouted/pointed in cement mortar, disposal of unserviceable tiles and debris/rubbles from site complete all as specified and directed. |
| 68 | Demolition of cement Concrete of any description and in any position including any type of roof treatment, sunken portion, PCC padding, lime concrete, mud etc on roof, complete all as spd and directed. Note: All demolished material / debris will be disposed off out side the Airforce station Nal with out any extra cost to the govt. Contractor should arrange dumping site to dispose off material. |
| 69 | M&L for Cement concrete 1:2:4 type B0,(using 12.5 mm graded stone aggregate) as in roof paddding,mass concrete finishing as required gradient cement concrete surface even and smooth without using extra cement including water proofing compoundcomplete all as spd and directed. |
| 70 | M&L for 15mm thick screed beddingincement mortar 1:4 mixed with water proofing compound pidi proof LW @ 200ml per 50Kg cement as per manufacturers instructions on concrete surface of roof and finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge (WPC shall be measured and paid separately) |
| 71 | M&L for APP based polymeric membrane minimum weight 3 Kg/Sqm and minimum 3 mm thick, reinforced with polyster non wove fabric (wt. not less than 150gms/Sqm ) laid by torch forced application over and including a priming coatusing bituminious primer @ 0.40litre/ sqm as per manufacturer\"s instruction on concrete surface complete all as specified and directed by Engineer in charge. |
| 72 | M&L for 20mm thick Pre-cast Cement concrete tiles 1:2:4 type B0,(using 10 mm to 12.5 mm graded stone aggregate), with grey cement & no pigment machine pressed; set jointed and pointed in cement mortar1:3, laid over and including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 73 | Supply only Liquid water proofing compound ISI marked etc. |
| 74 | M&L Cement concrete in foundations, filling and mass concrete Type E2 (1:5:10) using 40mm graded stone aggregate as in sunken treatment,complete all as specified and directed |
| 75 | S&F in repair 40mm bore 600mm long GI spout pipe to drain out the surplus water from the sunken portion including cutting hole and making good the disturbed surface in PCC 1:2:4 type B1, complete as specified and directed |
| 76 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including20 mm thick screed bed in CM 1:6 complete all as specified . |
| 77 | M&L for Rounding to edges of stone slabs one edge such as in steps & platform etc complete all as specified and directed. |
| 78 | Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frames of doors, windows,ventilators and partitions (Fixedportions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required die and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as perthe direction of Engineer-in-Charge. |
| 79 | Supply and fixingPowder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws,rollers & dust proof brush for sliding door / windowcomplete all as per the direction of Engineer-in-Charge. |
| 80 | S & F 4.80 mm thick sheet glass of size n exc 0.5 sqm in each pane ordinary quality plain /tintedand including glazing with suitable rubber beads etccomplete all as specified and directed. |
| 81 | Anodised aluminum grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anode coating of grade AC15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with CP. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. |
| 82 | Taking down cement plaster on brick/stone/concrete walls /ceiling incl racking out joints etc,hacking for key, scrubbing down with water etc & dispose off debris upto a distance n exc.500 mtrs where directed complete all as specified and directed.Note:-( Rate applicable upto four storey height incling all scaffolding work) |
| 83 | M&L for 15 mm thick rendering in two layers i.e. 10 mm thick in cement mortar 1:4 in first layer and 5 mm thick in cement mortar 1:4 mixed with approved water proofing compound on top layer,on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement all as specified and directed. (Note:- Water proofing compound shall be measured & paid separately.) |
| 84 | M&L for preparation of newly plastered surface and apply two coats of Acrylic Smooth exterior paint of required shade applied over one coat of alkali resistant primer in camouflage pattern complete all as specified and directed. |
| 85 | M&L for rendering 15mm thick on fair faces of brick or concrete surfacesin CM 1:6 finished even and smooth without using extra cement |
| 86 | M&L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over a coat of chalk whitening over newly plastered surfaces of walls, pillars cornices etc complete all as specified and directed. |
| 87 | M&L for rendering 5 mm thick on ceiling in CM 1:3finished even and smooth without using extra cement, complete all as specified and directed. |
| 88 | M&L preparation of newly plastered surfaces ofceiling and applying three coats of white wash complete all as specified and directed. |
| 89 | M&L for preparation of old plastered/painted surfaces of walls and applyingone coat of Acrylic Smooth exterior paint of required shade in camouflage pattern complete all as specified and directed. |
| 90 | M&L for preparation of old plastered/painted surfaces of ceiling and applying one coat of white wash on ceiling complete all as specified and directed. |
| 91 | M&L for preparation of old plastered/painted surfaces of walls and applyingone coat of oil bound distemper on wall including cornices etc complete all as specified and directed. |
| 92 | S&F as in repair sinks with drainage board made of stainless steel sink of 1mm thick sheet, kitchen or laboratory with plug washer and waste pipe incl bedding in cement mortar 1:6 on to draft wall of including fixing cantilever brackets and connecting unions overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 93 | S & F in repair vitreous chinawhitewash down water closet pan (pedestal pattern) including white plastic seat cover with CP hinging device and PVC P type trap, including connection to trap, drain pipe, flushing cistern & anti syphonage pipe complete all as specified.Note : The cost of traps and plastic seat cover are included in this item. |
| 94 | S&F in repair 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve float handle including bracket and flush pipe of polythylene of low or high density or PVC,32mm dia complete all as specified and directed. Note:- Flush tank can be concealed in wall if reqd i.e in the case of wall hung type water closet pan |
| 95 | Supply& fixingas in repairs wash hand basin, vitreous china, white, decorative type, flat or angleback, size 580mm x 450mm inclusive ofwaste pipe and brass coupling and including cutting for and pinning in ends of brackets or erecting stand and inclusive of cost of brackets complete all as specified and directed. |
| 96 | Supply& fixingas in repair PVC bath cabinet, size 622mm x 422mm, comprising of lookingglass, space for bath soaps, shampoo, tooth brush and paste, hand towel rail, complete all as specified and directed. |
| 97 | Supply and fixing in repair brass chromium plated tubular towel rail 20mm dia \"D\" type 60 cm long between flanges complete all as specified and directed. |
| 98 | Supply and fixing as in repair soap dish chromium plated of size 100 x 100 mm any type, fixed with chromium plated brass screwscomplete all as specified and directed. |
| 99 | S & F as in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, complete all as specified and directed. |
| 100 | Supply and fixing as in repairs faucet health (hand jet) 15mm bore cast copper alloy, chromium plated with flexible chromium plated connection pipe 1.5 mtr length, with fittings, complete all as specified and directed. |
| 101 | S & F as in repairs Two way angle cock Quarter turn cast copper alloy 15 mm bore chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union fixed complete all as specified and directed. |
| 102 | S & F as in repairs angle cock Quarter turn cast copper alloy 15 mm bore chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union fixed complete all as specified and directed. |
| 103 | Supply and fixing as in repair central hole Basin Mixer long swang nack, without poup waste system with 450mm long copper pipes and brass nuts, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. |
| 104 | Supply and fixing as in repair central hole Sink Mixer long body swang nech for mixing Hot & Cold water, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. |
| 105 | S&F as in repair Brass CP wall mixer 2-in-1 system with provision for over head shower complete with 115mm long bend pipe on upper side, connecting legs and wall flange for mixing hot and cold water screwed down for iron pipe 15 mm complete all as specified and directed. |
| 106 | Supply & fixingas in repair chromium platedshower rose with or without swivel joints 125mm dia including fixing to steel pipe,complete all as specified and directed. |
| 107 | Supply& fixing as in repair toiletpaper holder of brass chromium plated, complete all as specified and directed. |
| 108 | Supply& fixing as in repairs PVC waste down pipeof 32/40 mm bore for basin, complete all as specified and as directed. |
| 109 | Supply and fixing as in repairs 15mm dia PVC connection of length 450 mm, with PTMT nut, complete all as specified and directed. |
| 110 | Taking up or down 15mm dia steel tubing and connections with all fittings all as specified and directed. |
| 111 | S&F 15mm dia GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floors all as specified and directed. |
| 112 | Refixing 15mm bore GI tubing in new or old positionincl cleaning or rerunning threads and including new fittings, complete all as specified and directed. Note :- Serviceable pipe obtained from item no110 shall be used after necessary cleaning |
| 113 | Taking up or down 20mm dia steel tubing and connections with all fittings, complete all as specified and directed. |
| 114 | S&F GI pipe medium grade 20 mm dia with all fittings laid in floor or fixed in walls,complete all as specified and directed. |
| 115 | Refixing 20mm bore GI tubing in new or old positionincl cleaning or rerunning threads and including new fittings complete all as specified and directed. Note :- Serviceable pipe obtained from item no113 shall be used after necessary cleaning |
| 116 | S&Fin repair15 mm dia Bib taps, long shank quarter turn , cast copper alloy with crutch or butterfly handle, screwed down, crewed with flange cap for iron pipe or for brass ferrule and fixed, complete all as specified and directed. |
| 117 | Demolition and breaking up drain pipes 110/75 mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, complete all as specified and directed. |
| 118 | S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, incl PVC straps/clamps fixed to walls bore of the pipe 110 mm,complete all as specified and directed. |
| 119 | S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches of bore of the pipe 75 mm, complete all as specified and directed. |
| 120 | S&F PVC(SWR) bends 110 mm dia, complete all as specified and directed. |
| 121 | S&F PVC(SWR) bends 75 mm dia complete all as specified . |
| 122 | S&F PVC(SWR) bends 110 mm dia. With access door |
| 123 | S&F PVC (SWR) junction single, (Single T) equal or unequal with access door110 mm bore complete all as specified |
| 124 | M & L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement of any descriptioncomplete all as specified . |
| 125 | S&F in repair 75mm dia PVC (SWR) floor trap plain with CP grating including jointing with solvent cement incl necessary PCC & form work as required complete all as specified and directed. |
| 126 | Cleaning and removing all scale and dirt from RCC / PVC tank capacity of tanks exc. 250 ltrs and up to 500 ltrs by emptying, drying, cleaning with chlorine/washing powder by scrubbing the dust with wire brush from tank by removing inlet and outlet pipe and refixing inlet and outlet pipe with new tank connection fitting in the same position after cleaningand marking the date of cleaning on the tank with paint complete all as specified and directed. Note:- \"Writing\"CLEANED ON DD/MM/YY\" on service water tank with letters or figures (Block. Roman) of size 5 cm high and min 5cm wide each, complete all as specified and directed. |
| 127 | S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm borecomplete all as specified and directed. |
| 128 | Dismantling water tanks any type of capacityExc 250 but n.exc 500 litrescomplete all as specified and directed. |
| 129 | S&F 500 litre capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) tripple layered white, hoisted and fixed in position, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed. |
| 130 | S&F 20mm PTMT nipple suitable for HDPE water tank (minimum weight 45gms) complete all as specified . |
| 131 | S&F Stainless steel ( SS 202 grade ) curtain rod25 mm dia 0.80 mm wall thickness, mild steel, chromium platedincluding supporitng brackets and all fittings as per sample complete all specified and directed. |
| 132 | M&L forproviding, cement concrete type B-1, 1:2:4 (20mm graded stone aggregate)as in haunching, coping , benching etc complete all as specified as directed. |
| 133 | M&L for hard core ofbroken bricks of guage n.exc 63mm deposited spread and levelled in layer n.exc 15cm thick watered and well rammed to true surfaces as complete all as specified as directed. |
| 134 | M & L for providing 75 mm thick PCC (1:4:8) type D-2 (using 40 mm graded stone agg.) in sub base of flooring and all as specified and directed. |
| 135 | M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 -2006 of 60mm thickness M-35 grade, with grey cement, pigment with 25mm thick sand filling all as specified and directed. |
| 136 | Excavation in post holes (or similar holes) in hard/dense soil, each in not exc. 0.50 cum getting out returning,filling in an ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm watering and removing surplus soil out of defence land and making good surface all as specified & directed. |
| 137 | M&L for cement concrete type C2 1:3:6(40mm graded stone aggregate) as in posts( including caps and bases),complete all as specified as directed. |
| 138 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 139 | M&L for steelwork in tubular trusses, post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979, IS-4923-1997 grade st-240 & above, including embedding in concrete complete and all as specified and directed. |
| 140 | S&F MS plain plates, square cut, with riveted, bolted or welded attachment FE-410-W (Gde-E-250) quality A, complete and all as specified and directed. |
| 141 | S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n.exc 5cm long, diameter of neck in 5 to 10mm, complete all as specified and directed. |
| 142 | Dismantling Asbestos cement or CGI Sheet (corrugated or semi corrugated) or galvalume aluminium zinc coating GI based corrugated steel sheeting in roof covering complete all as specified and directed. |
| 143 | M/L for Pre- painted galvalume aluminium zinc coatingGI based corrugatedor semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.. |
| 144 | Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed. |
| 145 | Material and labour forpreparationof new wooden surfaces of any description not other describe ver 10cm width or girth and applying twocoats of synthetic enamel paintover one coat of pink primer, complete all as specified and directed. |
| 146 | M&L for preparation of old painted surfaces of Steel and Iron work of any description exc 10 cm width or girth applying one coat of synthetic enamel paint on steel surface all as specified, complete all as specified and directed. |
| 147 | M&L for preparation of old painted surface of wood and wood based materials of any description not otherwise described over 10 cm. width or girthshallapplying one coat of synthetic enamel painting overthe wooden surfaces all as specified & directed. |
| 148 | Material and labour for repairing of soffits of slabs/Chajja, Facia and similar works by dismantling of loose/ disintegrated portion of RCC at any height and in any situation, including provn of support,formwork and welding of reinforcement and fixing in position and with provision of weld mesh, applying dubbing 1st coat of 20 to 25mm thick in CM 1:3 finished rough and finishing coat of 10mm thick in CM 1:3 finished even and smooth without using extra cementover and including cement slurry @ 3 kg/sqm, finished even and smooth to desired shapeand applyingtwo coats of weather proof exterior emulsion paint over a coat of acrylic resistant primer to match with existing surfaces complete all as specified and directed.(weld mesh measured and paid separately)Note:- (i) Unit rate of this item includes the cost of scaffolding, formwork etc. and nothing extra shall be paid on account of variation in height.(ii) For payment purpose, the area of finished plaster in 2nd coat shall be considered. |
| 149 | S&F in repair MS framed work such as grills, gratings,guardbar with ends of bars shouldered and or riveted or forged into spikes, framed guard bars and similar work confirming to Fe 410 or Fe 310-0 including dismantling old complete all as specified. |
| 150 | Taking down Rolling shutter with frame ofsizeupto 20sqmof any description complete all as specified and directed. |
| 151 | Takingdown carefully copper /aluminium point wiring light/fan, socket or power point /AC point complete including fittings such as switches, sockets, ceiling rose, bell push, bell buzzer, lamp holder bracket, fan regulator, tube light fitting removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditioning separately ) and making good disturbed surfaces of walls,floor ,etc. complete all as specified and as directed. |
| 152 | M & L for point wiring using 1.1 kV grade single core FR-LSH flexible cable, conforming to IS 694: 2010, having multi-drawn thin strands of electrolytic copper conductors and insulation for phase, neutral, and earth continuity conductor connecting to earth dolly, colour-coded as per IS 11353: 1985, drawn in medium grade UPVC surface / recessed conduits, conforming to IS 9537 (Part- 3): 1983, of size not less than 20 mm NB, including cutting chases,conforming to IS 14772: 2000, having top, bottom, side and back-wall knockouts for conduit entry from any direction, suitable modular cover-plates and making good of disturbed surfaces of wall / ceiling / floor, etc. complete all as specified in IS 732: 2019 and directed by the engineer-in-charge. Notes- [i] Wiring from the DB (distribution box) to terminal boxes for power plugs, fan regulators, switches, socket outlets, etc. shall be deemed inclusive in the quoted rates.(ii)The wiring shall be provided in standard colour code(iii) The quoted rate is deemed to include for cutting/chasing for concealing the conduit and making good the surface to match the existing surfaces.(iv) In case of ceiling portion where concealed conduiting is not possible, the surface conduit shall be provided ad directed.(v) The earth wire shall be connected to common earth and each terminal boxes and fitting all as directed. |
| 153 | One fan/light/bell point controlled by one switch, with cables 1.5 mm² size |
| 154 | One 3 pin socket outlet, 5/6 amps, on independent board, with cables 1.5 sq.mm size |
| 155 | One 3 pin socket outlet, 5/6 amps, onsame board, with cables 1.5 sq.mm size |
| 156 | One 3 pin socket outlet, 15/16 amps, independent board, with cables 2.5 sq.mm size |
| 157 | S & F Socket 6A/16A - 2/3 pin combined 2 module combinedswitch socket, conforming to IS 1293: 2005 complete all as specified in IS 732: 2019 and directed by the engineer-in-charge. |
| 158 | S & F modular type 2/3 pin shuttered type 5/6 A socket, conforming to IS 1293: 2005 complete all as specified in IS 732: 2019 and directed by the engineer-in-charge. |
| 159 | S & F modular type 15/16 A 1-way SP switch conforming to IS 3854: 2012 with finger-proof terminal complete all as specified in IS 732: 2019 and directed by the engineer-in-charge. |
| 160 | S & F modular type 5/6 A 1-way SP switch conforming to IS 3854: 2012 with finger-proof terminal complete all as specified in IS 732: 2019 and directed by the engineer-in-charge. |
| 161 | S & F Modular Bell push 6A 1 module conforming to IS 3854: 2012 with finger-proof terminal complete all as specified in IS 732: 2019 and directed by the engineer-in-charge. |
| 162 | M & L for ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all as specified and as directed. |
| 163 | S & F Modular cover plate with frame of following module complete all as specied and directed. Note- Modular switches, sockets and cover plate with frame shall be of same make and model. |
| 164 | 8 Module |
| 165 | 6 Module |
| 166 | 3 Module |
| 167 | 2 Module |
| 168 | S & F rectangular modular metal flush mounted sunken block of following modules suitable for mounting modular switches & sockets complete all as specified and directed |
| 169 | 8 Module |
| 170 | 6 Module |
| 171 | 3 Module |
| 172 | 2 Module |
| 173 | Supply and fixing modularstepped type electronic fan regulator , SP 230 Volt100/120 watt complete all as specified and directed. |
| 174 | Supply and fixingelectronic Bell,AC. 230 volts, single pole complete all as specified and directed by Engr-In-Charge. |
| 175 | S&F energy saving decorating box type batten light fitting 230 volts surface mounted complete with high efficiency glare free light LED lamp 20 watt(4 Feet)blue coloured end caps with all accessories, pre- wired,aluminium housing,polycorbonate diffuser integrated heavy duty electronic driver having THD < 10% including providing flexible copper wire twin core cable complete all as specified and directed by Engineer in charge. |
| 176 | Supply and fixing integratedLED bulk head luminaire 1 x 10 watt comprising of pressure die cast housing, acrylic diffuser & frameIP65 protection & available in 5700k (CDL) & 3000K (WW) colour temperatures pre-wired incl connection with flexible twin core wire complete all as specified and directed. CAT REF- LBHN-10-CDL, MAKE-crompton greaves or equivalent of philips//Havells. |
| 177 | S&F energy saving decorating box type batten light fitting 230 volts surface mounted complete with high efficiency glare free light LED lamp 10 watt(2 feet) blue coloured end caps with all accessories, pre- wired,aluminium housing,polycorbonate diffuser integrated heavy duty electronic driver having THD < 10% including providing flexible copper wire twin core cable complete all as specified and directed by Engineer- in- charge. |
| 178 | Supply and fixing decorative type Wall light LED1 x 10 watt comprising of pressure die cast housing, acrylic diffuser & frameIP65 protection & available in 5700k (CDL) & 3000K (WW) colour temperatures pre-wired incl connection with flexible twin core wire complete all as specified and directed. |
| 179 | M&L Dismantling blades, down rod, canopy and taking out burnt stator assy of ceiling fan 48\"/56\"sweep and taking down old burnt copper stator winding, cleaning stator slots, rewinding of stator assy with appropriate gauge of super enamelled copper winding wire, insulating material complete and assembling ceiling fan and testing for proper function including provision of split pin of suitable sizes and writing MES No ( Letter size shall be minimum 5 mm width x 15 mm height)complete all as specified and directed.Note:(i) Cost of taking down of fan and re-fixing shall be included in the unit quoted rate(ii) The quoted rate for rewinding shall also include the rates of ball bearing/Bush bearing, capacitorof suitable size.(iii) painting and writing MES no also to be included in the quoted rate |
| 180 | M&L for Taking down existingceiling fan of size 48\" or 56 \"from fan hook servicing ofceiling fan,cleaningthoroughly,greasingball bearings, oiling bushbearing, replacing splitpin and rubberreal and including complete enamelled painting workand fixingbackin position complete all as specified and directed. |
| 181 | Taking down of unserviceable geyser of 50 ltr capacity of any make from the wall after disconnecting and opening of nuts and bolts carefully for repair andrefixing the same, after repair,in original location and connecting to water mains and electric supply after carrying out the repair work complete all as specified and directed. Note:- (i) Cost of taking down of Geyser and re-fixing shall be included in the unit quoted rate(ii) The quoted rate for replacement of heating element, thermostat, syphon, inlet/outlet PVC Pipe connection shall also include .(iii) painting and writing MES no also to be included in the quoted rate. |
| 182 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm with complete all as specified and directed. Note:- Old unsv exhaust fan shall be deposited to MES Store. |
| 183 | Supply and fix exhaust fan, steel body AC single Phase. 230V, 50Hz of size 300m sweep with, blades, and frame and louverswith complete all as specified and directed. Note:- Old unsv exhaust fan shall be deposited to MES Store. |
| 184 | S&F sheet metal enclosure single pole and neutral enclosure with two pin and earth plug and socket complete with one MCB SP 20 Amps complete all as specified and directed. |
| 185 | M&L for taking down carefully existing sub main wiring on wall (different sizes) and making concealed by refixing/ drawnthrough including cutting chases in any type of masonry including suitable size of non-metallic PVC conduit fittings accessories and making good the disturbed surface match with the existing all as specified and directed. |
| 186 | Supply and laying sub main wiring complete with 03 runs ( phase, Neutral & Earthing colour code) of single core 10 sqmm fire retardant low smoke (FRLS)PVC insulated copper conductor cable multistranded and sheathedLT 1100 V grade drawn through andincluding concealed non metallic PVC conduit minimum dia 20mm dia ISI marked andaccessories surface fixedon wall /flooretc all as specified. Note:- 03 runs of cable and 01 run of PVC conduit shall be considered as one unit for measurement purposes. |
| 187 | Supply and laying sub main wiring complete with 03 runs (Phase, Neutral & Earthing colour code) of single core 6 sqmm fire retardant low smoke and halogen (FRLSH)PVC insulated copper conductor cable multistranded and sheathedLT 1100 V grade drawn through and including concealed non metallic PVC conduit minimum dia 20mm dia ISI marked andaccessories surface fixedon wall /flooretc all as specified. Note:- 03 runs of cable and one run of PVC conduit shall be considered as one unit for measurement purposes. |
| 188 | Supply and laying sub main wiring complete with 03 runs (Phase, Neutral & Earthing colour code) of single core 4 sqmm fire retardant low smoke and halogen (FRLSH)PVC insulated copper conductor cable multistranded and sheathedLT 1100 V grade drawn through and including concealed non metallic PVC conduit minimum dia 20mm dia ISI marked andaccessories surface fixedon wall /flooretc all as specified. Note:- 03 runs of cable and one run of PVC conduit shall be considered as one unit for measurement purposes. |
| 189 | Taking down carefully Distribution board SPN /TPN of any sizes & any capacity by unscrewing including MCB SP/SPN from existing location all as directed. |
| 190 | Supply and fixing MCB DB single pole and neutral 240 volt SPN 8 way with 200 Amps rated bus bardouble door type complete all as specified and directed. Note : Rate quoted shall deemed to be including for cutting existing wall for fixing DB in concealed making connections of sub main wiring (incoming and outgoing) with suitable size of cable lugs etc. and making good the existing surface. |
| 191 | Supply and fixing MCB SPN 32 Amps 240Volts, Breaking capacity 10 KA \"C\" curve complete all as specified and directed. |
| 192 | Supply and fixingMCB SP 5-32 Amps 240Volts, Breaking capacity 10 KA \"C\" curve complete all as specified and directed. |
| 193 | Supply and fixing vertical TPN DB double door, IP 45 protection with powder coated enclosure 4 way insulated busbar assembly including MCCB 4 pole, 415 V, 100/125A, 16 kA - 01 No complete all as specified and directed. |
| 194 | M&L for earthing complete with GI earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.50Mtr below ground level.The earth plate to be connected with earth lead of 4 mm dia galvanised iron or steel wire all as shown inelectrical plate no 3, connected to earthing test pointall as specified and directd.The GI earthing stripto be protected by galvanised iron pipe 40 mm bore (medium grade) up to ground level and there after with40mm dia HDPE pipe up to test point. Earthing shall be include withproviding funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) up to 90 cm all around earth platefurther filled with60 cm thick Tibba sandand 2nd layer with30 cm of Magnesium sulphate powder (compact thickness ) , 3rd layerwithtibba sand up to the ground level. Earthing shall also be include for providingconcrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded stone aggregate), 50mm thick precast RCC (1:2:4) using graded stone aggregate cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work including taking out old unsv earthing from existing location with complete all as specified and directed. |
| 195 | Supply and fix as in repairs LED street light 45 watt 230 volts pressure die cast aluminium housing, heat resistant toughened glass with frame, IP protection IP.66 batter optics for uniform including GI bracketwith fixing on wall and taking outexisting old unsv light complete all as specified and directed. |
| 196 | M&L for disconnecting from the existing location cutting off worn out aluminium cable end and Supply, laying and testing in replacement cable XLPEInsulated ,screened, PVC bedded,galvanized steel strip or wire armoured,electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core including taking out existing cable of any size. |
| 197 | Material and labour for tiba sand for filling in trenches below and around underground cables for cushioning of cables etc, complete all as specified.Note:- Punned thickness shall be measured for payment purpose. |
| 198 | S&F sub class B bricks having minimum compressive strength 75 Kg/ Sqcm laid in trenches for cable protection etc complete all as directed by Engineer-in-Charge. |
| 199 | Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding techniqueand necessary machine or manually without damage nearby electric cable, water pipe line etc including HDPE pipe of 40 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed. |
| 200 | Supply,laying and testing in replacement GI water tubing 50 mm bore, medium grade with all fittings with screwed and socketed joints and fixed in trenches and making good the disturbed surface complete all as specified and directed. |
| 201 | Supply,laying and testing in replacement GI water tubing 25 mm bore, medium grade with all fittings with screwed and socketed joints and fixed in trenches and making good the disturbed surface complete all as specified and directed. |
| 202 | S & F in replacementGun metal Ball valve suitable for 50 mm bore pipe complete all as specified and directed. |
| 203 | S & F in replacementGun metal Ball valve suitable for 25 mm bore pipe complete all as specified and directed. |
| 204 | M&L for disconnecting from the existing location cutting off worn out aluminium cable end and Supply, laying and testing in replacement cable XLPEInsulated ,screened, PVC bedded,galvanized steel strip or wire armoured,electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core including taking out existing cable of any size. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
