|
| 1 | Supply and fixing of 9 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm, thickness with double arm bracket length of 1 mtr. length in 1:2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect. Arm design will be as per direction of Engineer-in-charge |
| 2 | Supply and fixing of LED Street light Fitting with mandatory driver set having die cast aluminium body with toughend glass/ UV stabilized PC Cover and lenses suitable for 110 Watt to 130 Watt and Confirming to IP 66, and IK07 and above protection having Company LOGO Engraved complete in all respect including Labour.CAT-AAA13200-15600 system lumens, High Power LED with lenses, 120Lm/W, PF>0.95, THD <10% at full load, CRI >70, Potted driver Set in Metal housing (Not Circuitory), Phase to phase Protection at 440V & >300V auto cut and re-start feature, 4KV internal Surge protection, with 5 years warrantee. Make:- Philips/Havells |
| 3 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 4 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 5 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 6 | Supply and fixing of 5 Amp. To 32 Amp. Rating 240/415 V 10 kA C-Curve MCB for Controling of Street Light DP MCB. |
| 7 | Supplying and Laying of FRPVC Round Shethed DPMCB copper Conductor flexible cable including making connection street light 21 Mtr. Wire for 2 Nos. Street Light 3 Core 1.5 Sq.mm copper wire. |
| 8 | Nubering of pole & panel by letter writing |
| 9 | Supply and fixing of 16 mtr. High mast shaft of approved make with rising system hot dip glavanized inside & out side dip, heaving pole sheet thickness 4mm. Top dia minimum 150 mm, bottom dia minimum 360mm, base plate 32mm thick, suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5 HP power tool moter, 3 point suspension system with steel wire rope 6mm dia,double drum winch. including making suitable foundation as per manufature drawing/site reuiment along with foundation bolts nuts, washers, anchor plates etc complete in all respect. |
| 10 | Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing with toughend glass/UV stabilized PC Cover and lenses built with mandatory driver set suitable for 170 to 200 Watt. Confirming to IP 66, IK 07 and above protection complete in all respect including Labour.CAT-AAA 20400-24000 system lumens, High power LED with lenses, >120Lm/W, P.F.>0.95, THD <10% at full load, CRI >70, Potted driver Set in Metal housing (Not Circuitory) Phase to phase Protection at 440V & >300V auto cut and re-start feature, 4 KV internal Surge Protection, with 5 years warrantee Make:- Philips/Havells |
| 11 | Supply & Laying of PVC Round Shethed copper Conductor flexible cable including cable connection to 12 Nos. flood light. (for High Mast Light) with 2.5 Sq. mm 3 Core Copper Conductor |
| 12 | Providing, laying and fixing 100 mm. dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. |
| 13 | Cost of road/floor restoration after road cutting including cost of labour T&P material etc. complete |
| 14 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts in Existing DWC HDPE pipe as directed by Engineer Incharge, complete in all respect including excavation and reffilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. |
| 15 | 16 sq. mm 4 core |
| 16 | 35 sq. mm 3.5 core |
| 17 | 70 sq. mm 3.5 core |
| 18 | Supply and Laying of following size DWC HDPE Pipe ISI Mark along with all assoseries like socket bend coupler etc. confirming to IS 14930 Part-II complete with fitting and cutting jointing etc. direct in ground (75 mm below ground level) including exvaution and reffling the trench but excluding sand cusining and protective covering etc. complete. |
| 19 | 63 mm dia (OD 63 mm & ID 51 mm nominal) |
| 20 | 90 mm dia (OD 90 mm & ID 76 mm nominal) |
| 21 | Supply & Making end Termination with Brass Compression gland & Alu. Lugs for following size Alu. Conductor cable of 1.1 KV Grade |
| 22 | 16 sq. mm 4 core |
| 23 | 35 sq. mm 3.5 core |
| 24 | 70 sq. mm 3.5 core |
| 25 | Supply and fixing of 100 Amp./415 V on load main switch complete in all respect Havells or Eq. make . |
| 26 | Supply&Erraction of factory fabricated &wired metal clad dest and vernin proof floor mounting M.S. channel base with bottom and top cable centries electrical control panel withTPN MCCBs(Four pole 36KA with thermal magntic release) Switches Complete and instruement chamber etc. complte inall respect,The instruement chamber shall be scparteand shall comprise of Flash type digital metering system for phase voltage and single phase voltage current and other parameters (KVA ,P,F, KW) in each phase with touch type selector switches for different reading instrument fuses current transformer etc. The panel board shall have suitable capacity electrolytic aluminium busbars as per IS8623 or above insulated with best shrink sleeving and mounted on non hygroscopic supports suchas CMC/BMC support with dettcacbable silde cover and shall be suitable for extension on the slder. The MCCB\"s shall be complete with suitable for extension glands and indicatings lamp on incoming ete. panel will be outdoor type. The job includes the grounting of board as per directions of Engineer -in charge ,All out goings shall have an Ammters of 1.6 mm/2mm Cubicle type switch board shall be of cat A &B only. Incoming 100A 36KA ,FP MCCB-1no. & Outgoing 32 Amp. 25 KA MCCB-3 no. |
| 27 | Supply&Erraction of factory fabricated &wired metal clad dest and vernin proof floor mounting M.S. channel base with bottom and top cable centries electrical control panel withTPN MCCBs(Four pole 36KA with thermal magntic release) Switches Complete and instruement chamber etc. complte inall respect,The instruement chamber shall be scparteand shall comprise of Flash type digital metering system for phase voltage and single phase voltage current and other parameters (KVA ,P,F, KW) in each phase with touch type selector switches for different reading instrument fuses current transformer etc. The panel board shall have suitable capacity electrolytic aluminium busbars as per IS8623 or above insulated with best shrink sleeving and mounted on non hygroscopic supports suchas CMC/BMC support with dettcacbable silde cover and shall be suitable for extension on the slder. The MCCB\"s shall be complete with suitable for extension glands and indicatings lamp on incoming ete. The job includes the groonting of the board as per directions of Engineer in charge .All out going of 100amp and above shall have Ammeter ,The pannei board shall be fabricated with CRCAsheet with a minimium thickness of 1.6 mm/2.0 mm Cubicle type switch board shall be of cat A&B only.panel will be out door type. Incomer: 32A FP ,25ka MCCB with ThermalO/L & S/C Protection release along with Incoming Phase Light &contactor automatic street light control Timer Switch ete-1No with proper arrangements for connection of incoming cables Outgoing - 25 A FP, MCCB- 01 No. & 16A FP MCCB -03 Nos with additional Bus bar scpearately at each outgoing with 4way arrangment for proper connection of outgoing cables as directed by engineer in charge. |
| 28 | Supply & Erraction of factory fabricated& wired metal clud dust and vernin proof floor mounting M.S. Channel base 32A High mast,The panel fabricated out of 2.0 thick CRCA sheet steel painted with powder coated paint of shade as per the direction of Engineer in -charge after proper sheet treatment process of sheet steel. The Feeder Pillar shall be provided with Neopcene gasket to achive Degree of Protection IP:55 as per IS:8623 suitable for Outdoor installation ,All indicating Lights shall be LED type and all wiring shall be done from PVC insulated copper flexible wire . The panel shall be completed in all respect and shall consist of following material, Incomer :32A FP, 25 KA MCCB with Thermal O/L &S/C Protection release-1nos Outgoing :16AFP ,10KA MCCB with Thermal O/L & S/C Protection -2nos Outgoing :25A FP ,10ka MCCB with Thermal O/L &S/C Protection-01 no Note:- Contractor ,Thermal O/L Relay ,Reveres/Forward Push Button etc.-01 |
| 29 | Total Cost Please Enable Macros to View BoQ information |
