|
| 1 | Material and labour to lifting andloweringtonon-clog sewage submersible pump set of capacity 20 to 27 HP from sewage well / collection chamber including disconnecting electric connection carefully from panel board, bolts nuts washers, rubber gasket etc with supply and fixing new nutt, bolts, washer, rubber gasket all other necessary site required work for making functional to submersible pump motor set of following capacity.Note:- Quoted rate shall deemed to be included cost of(i)Required size and quantity of nut, bolts, washers and gasket.(ii) Required tools and plants shall be arrange by contractor. (iii) Repair of motor/pump/submersible cable shall be measured and paid under relevant item of schedule. |
| 2 | Labour forde-coupling, dismantling of non-clog sewage submersible motor body carefully set of capacity 20 to 27 HP and transportation to workshop for repair, dismantling the pump set by hydraulic jack, complete segregation of the pump and motor, checking the pump and motor thoroughly,removing the defective parts,re-assembling the pump set in the respective sewage well / collection chamber.(Note: Necessary spare part shall be measured & paid saperately under relevant item.) |
| 3 | M&L for cutting and removing the burnt windings of non-clog sewage submersible pump set of capacity 20 to 27 HP and rewinding the same above items using existing size /gauge/ qty of insulated supperior quality water proof copper winding wire of suitable size/gauge and nos of turns using insulating materials and non-clog submersible copper cable in suitable size required Lenght outside minimum 1.5 Mtrs, re-assembling ,full load testing, heating, drying , varnishing, overhauling,re-installation, commissioning, testing and connecting up complete all as existed following capacityall as directed.Note:- (i) Necessary testing shall be done by contractor after lowering in borewell at site. (ii) Quoted rate are included cost of cutting, removing, welding of motor body for making functional of pump set. |
| 4 | Taking out of centrifugal pump set of capacity 1 to 10 HP from foundation after disconnecting from suction and delivery pipe and including transportation to workshop for repair of unserviceable parts complete all specified and directed.(Note: Necessary spare part shall be measured & paid saperately under relevant item.) |
| 5 | M&L for re-winding to burnt out centrifugal motor body primary winding as same in existing size/guage/no of turns/qty or insulation etc using superior quality water proof copper winding wire and including re assembling, full load testing, heating, drying varnishing, overhulling, re installation, commisioning, testing and connecting up complete all as existed of motor 10 HP,3 Ph, 415 Volt.Note:- (i) Necessary testing shall be done by contractor after connection at site. (ii) Quoted rate are included cost of cutting, removing, welding of motor body for making functional of pump. |
| 6 | All as per item No 5 here-in-before but capacity of motor 7.5 HP , 3 Ph, 415 Volt . |
| 7 | All as per item No 5 here-in-before but capacity of motor 5 HP, 3 Ph, 415 Volt . |
| 8 | All as per item No 5 here-in-before but capacity of motor 1 to 3 HP, 3 Ph, 415 Volt . |
| 9 | Supply only of Pump shaft stainless steel sleev suitable size for 20 to 27 HP submersibale pump complete all as specified and directed. |
| 10 | Supply only of Impeller gunmetal/Brass of suitable for 20 HP to 27HP submersible pumps complete all as specified and directed. |
| 11 | Supply only Shaft key of sizes suitable for upto 27 Hpmotor complete all as specified and directed. |
| 12 | Supply only of Neck ring gun metal of suitable size for 20 to 27HP complete all as specified and directed. |
| 13 | Supply only of Neck ring gun metal of suitable size for 7.5 to 10HP complete all as specified and directed. |
| 14 | Supply only of Gun metal bowl bushes suitable for submersible pump of 20 to 27 HP complete all as specified and directed. |
| 15 | Supply only of Gun metal bowl bushes suitable for submersible pump of 2 HP to 7.5 HPcomplete all as specified and directed. |
| 16 | Supply only of Cast iron suction /discharge case bowl of suitable size Upto 27 HP complete all as specified and directed. |
| 17 | Supply only of Cast iron suction /discharge case bowl of suitable size from 7.5HP to 12.5HP complete all as specified and directed. |
| 18 | Supply only of iron Water seal for motor of capacity upto 10 HP motor completeall as specified and directed |
| 19 | Supply only Ball bearing No-6305 completeall as specified and directed. |
| 20 | Supply only Ball bearing No-6306 completeall as specified and directed. |
| 21 | Supply only Ball bearing No-6307 completeall as specified and directed. |
| 22 | Supply only Ball bearing No-6308 completeall as specified and directed. |
| 23 | Supply only Motor terminal box for 3 Hp to 12.5 Hp motor completeall as specified and directed. |
| 24 | Supply only Fan blade made with Alluminium alloy suitable for Centrifugal motor complete all as specified and directed. |
| 25 | Supply only of coupling bolt made of stainless steel with nut and washersuitable for Pump and motor 3 hp -12.5 Hp complete all as specified and directed. |
| 26 | Taking down air blower of capacity 20 HP, RPM 1460, from the existing position after disconnecting all electrical connection and transportation to workshop for repair of unserviceable parts complete, valve plate sheet cutting and surfacing, shaft cutting, grinding and surfacing, supply of nuts, bolts an drill beats, removing the defective parts, repair, rewinding the air blower thoroughly including machine work and re-assembling the air blower, commissioning and testing complete to the entire satisfaction of the Engineer-in-Charge.(Note: Necessary spare part shall be measured & paid saperately under relevant item.) |
| 27 | Supply only of new Bearings for air blower complete all as specified and as directed. (MAKE: SKF Bearing No. 3309A or equivalent as approved by GE) |
| 28 | Supply only of mechanical seal for air blower complete all as specified and as directed. |
| 29 | Supply only of neoprene \"O\" ring for air blower complete all as specified and as directed. |
| 30 | Supply only of V-Belt of size C/62/1630 LP for air blower complete all as specified and as directed. |
| 31 | S & F in replacement Submersible Pump Starters In Sheet Enclosure Type MU-G2OH Fully Automatic Star - Delta Starter suitable for 7.5 to 10 HP Motor, 415V, 50 Hz, 3 phase Conforms to IS/IEC 60947-4-1 & IEC 60947-4-1,Protections Offered - Overload, Single Phasing,Phase reversal, Phase imbalance, Auto Restart Feature, Vibration proof enclosure with IP54 protection class, Indications Offered - ON/OFF, Voltage and Ampere completeall as specified and directed.Make L&T Catpart No SS96257 or equivalent as per List of Make in Particular Specification. |
| 32 | Labour for draining out water from Swimming pool of 50000 Glns capacity after opening sluice valves, plugs etc and cleaning the walls / bottom surface with the help of wire brushes and other cleaning device to remove sludge and cleaning with water for making ready to paint the surface masonry/mettalic complete all as specified and directed. Note- cleaning oftank will be carryout three times in entire period of contract. |
| 33 | Labour for draining out water from Semi- underground/balancing static water reservoir capacity 20000 gallons throughafter opening sluice valves, plugs etc and cleaning the walls / bottom surface with the help of wire brushes and other cleaning device to remove sludge and cleaning with water for making ready to paint the surface masonry/mettalic complete all as specified and directed. Note- cleaning oftank will be carryout three times in entire period of contract..Location: Swimming pool |
| 34 | Taking down motor 75 HP 415 volts, 1460 RPM after disconnecting all electrical connection nut, bolts from base plate and transportation to repair workshop and dismantling the motor stator, removing worn out copper winding, cleaning the stator and rewinding the same with super enamelled copper wire of existing size and specification and vernish the same with antimoisture heat resistance including varnishing and drying up slowly and including replacement of all types insulating tape, terminal plate, cable socket etc and reassembling the same, transporting to site for refixing in existing position for smooth runningcomplete all as specified and directed. |
| 35 | Taking out ofjockey pump set from pump foundation after disconnection from motor /suction and delivery pipe and transportation to workshop dismantling the same andsegregating of serviceable and unserviceable parts repairing and overhauling the pump set after replacement of defective parts and machine work and re-setting to the existing position connecting motor /all pipe line and commissioning and testing on full load to the entire satisfaction of Engr-in-Charge including two coats of synthetic enamel paint over a coat of primer including preparation of old painted surface complete all as speicified and directed. |
| 36 | Taking out of old 12.5 HP jockey induction motor of 3 phase 415 volts 50 Hz from the existing position after disconnecting all electrical cable earthing and pipe line/pump connection and transportation to workshop,dismantling the motor and rewinding the same with existing guage super enamelled copper wire of approved make varnishing the same and heating properly in heat chamber, re-assembling the motor after replacement of DE/NDE bearing terminal box all rusted nut and bolts and install the same to the existing position and apply 2 coats of synthetic enamel paints after successfully repairs and testingcomplete all as specified and directed. |
| 37 | Taking up water pipeline of any size any type including all fittings from trenches mild steelpipe (IS: 1239 Part-I) with flanged/socket and spigot ends includingall fittings viz, forged steel screwed fittings,flanges, bends, tees, reducers, elbow, clamps, hangers etc and kept in safe custody for reuse/disposal /taking credit the same for the following borecomplete all as specified and directed. |
| 38 | Supply and lay in trenches / fix to wall MS ERW pipe of 150 mm dia of heavy duty grade with reducer, bends, elbows, union etc complete and connecting to the existing pipe line complete all as specified and directed. |
| 39 | All as in Item No-38 above but for 100 mm bore |
| 40 | S&F bends (any type, radius and angle) tapers any type (strainght, bend, increasing, decreasing or double socket etc) tee pieces single brancehs \"Y\" junction double branch, cross (all socket or socket and spigot) collars, caps and plugs for pipe of Bore upto 150mm complete all as specified and directed. |
| 41 | S & F in repair Detectors Complying with and type certified to Addressable type multisensor heat & smoke detector with base with self built intelligence as per IS: 11360 complete all as specified and directed. |
| 42 | S & F in repair Fire alarm control panel complying with BS EN 54 Single loop panel of capacity from 99 detectors & 99 modules upto 200 detector and modules complete all as specified and directed. |
| 43 | S & F in repair Pressure gauge 4\"dial 0-14 kgs rating complete all as specified and directed. |
| 44 | S & F in repair Pressure switch Universal type complete all as specified and directed. |
| 45 | S & F in repair RRL hose type - A 15 m complete all as specified and directed. |
| 46 | S & F in repair Sluice Valve of dia 150mm Class PN 1.6 complete all as specified and directed. |
| 47 | S & F in repair non return Sluice Valve of dia 150mm Class PN 1.6 complete all as specified and directed. |
| 48 | S & F steam globe stop valve 25mm dia with hand wheel including necessary fitting suitable for steam line after taking out old onecomplete all as specified and directed. |
| 49 | All as in Item No- 48 above but for 20 mm dia |
| 50 | M&L for PCC (1:4:8) type D-2 with using 40 mm grade crushed stone aggregate as with necessary form work as required complete all as specified and directed. |
| 51 | M&L for opening of Multi grade filter , Activated cabon filter, Iron removal plant and Oxidation chamber of 10000 to 20000 GPH capacity, taking out and removing old filter media such as ferro, minex, PVC type strainer nozzles, carbo-felt, filter sand, gravel, grit etc. From filtration plant and depositing to distance exceeding 25m but not exceeding 50m complete all as specified and as directed.Note:- Stainer, Gravels shall be measured and paid seperatley under relevent items. |
| 52 | M&L for preparation of internal steel surfaces of iron removal filtration plant, Multi grade filter, Activated carbon filter and Oxidation chamber of 10000 to 20000 GPH capacity by scraping with wire brush and removing all dust, scales and other foreign particles and thoroughly washing with clean water and after drying apply two coats of anti-corrosive black bituminous paint suitable for drinking purpose on entire internal surfaces (except glavanised surfaces) of filtration plants and Navy blue paint on outer surfaces marking the date of cleaning on the body complete all as specified and as directed |
| 53 | Supply only PVC push type/ threaded type stainer suitable for filtration plant complete all as specified and as directed. |
| 54 | Supplying and charging in layers special fine sand suitable for use in filtration plant of size 2 X 6 mm mesh complete all as specified and as directed. |
| 55 | Supplying and charging in layers special coarse sand suitable for use in filtration plant of size 16 X 32 mm mesh complete all as specified and as directed. |
| 56 | Supplying and charging in layers new washed, cleaned, dust free, well graded gravels filter media suitable for use in filtration plant of the size 10mm complete all as specified and as directed. |
| 57 | Supplying and charging in layers new washed, cleaned, dust free, well graded gravels filter media suitable for use in filtration plant of the size 15mm complete all as specified and as directed. |
| 58 | Supplying and charging in layers new washed, cleaned, dust free, well graded gravels filter media suitable for use in filtration plant of the size 20mm complete all as specified and as directed. |
| 59 | Supplying and charging in layers new washed, cleaned, dust free, well graded gravels filter media suitable for use in filtration plant of the size 25mm complete all as specified and as directed. |
| 60 | Supplying and charging in layers new washed, cleaned, dust free, well graded gravels filter media suitable for use in filtration plant of the size 40mm complete all as specified and as directed. |
| 61 | Supply and charging in layers manganese dioxide (MnO2) and treated Carbofil in lumps of size 20mm to 15mm containing at least 75% of mangenese dioxide and 25% kg carbofil suitable for use in filtration plant complete all as specified and as directed. |
| 62 | Supply and charging in layers granule Authracite in lumps suitable for use in filtration plant complete all as specified and as directed. |
| 63 | Supply and charging in Activated carbon suitable for use in filtration plant complete all as specified and as directed. |
| 64 | Supply and charging in Live Catlytic media (Green sand) suitable for use in filtration plant complete all as specified and as directed. |
| 65 | Supply and fixing in repair Butter fly valve PN-1.6 150mm dia use in filtration plant complete all as specified and as directed |
| 66 | Supply and fixing in repair Butter fly valve PN-1.6 100mm dia use in filtration plant complete all as specified and as directed |
| 67 | Supply and fixing in repair Butter fly valve PN-1.6 80mm dia use in filtration plant complete all as specified and as directed |
| 68 | Maint and servicing of DG set 320-400 KVA conopy typewith AMF Panel (if installed ), through authorise service agencyofOEM , including replacment of defective/wornout parts with new spares such as filters, gaskets, V belts, Engine Oil, coolant for radiator rubber hoses with clamps, nuts bolts and cleaning of alternator with vaccum cleaner , including greasing of bearings of engine and alternator, tappet setting, checking of batteries, adding distilled water and cleaning of POL tankand radiator etcall as specified and directed. Make - Kirloskar/cummins/greaves/Ashok Leyland / As per OEMNote:-1. spares required for above maint will be measured and paid separately under relevent items of Schedule.2. All breakdown calls should be attended. |
| 69 | All as per Item No-68 Above but for DG set of capacity 180-250 KVA |
| 70 | All as per Item No-68 Above but for DG set of capacity 125-160 KVA |
| 71 | Supply only Fuel filter for 300-400 KVA DG set, Make : As per OEM |
| 72 | Supply only Fuel filter for 125-250 KVA DG set,Make : As Per OEM |
| 73 | Supply only Lub oil filter for 300-400 KVA DG set,Make : As Per OEM. |
| 74 | Supply only Lub oil filter for 125-250 KVA DG set,Make : As Per OEM |
| 75 | Supply onlyAir cleaner filter ( inner and outer ) for 300-400 KVA DG set, Make : As Per OEM. |
| 76 | Supply only Air cleaner filter (inner and outer ) for 125-250 KVA DG set, Make : As Per OEM |
| 77 | Supply only Bypass filter for 300-400 KVA DG set, Make : As Per OEM. |
| 78 | Supply only Bypass filter for 125-250 KVA DG set, Make :As Per OEM |
| 79 | Supply only V belt for 300-400 KVA DG set,Make : As Per OEM |
| 80 | Supply only V belt for 125-250 KVA DG set, Make : As Per OEM |
| 81 | Supply only Coolantfor radiators complete all as specified and directed. Make- As Per OEM |
| 82 | Supply only engine oil multi grade 15W40 complete all as specified and directed. Make- As Per OEM |
| 83 | S & F in repair Display control panel (Base card) for 125 to 250 kva DG set complete all as specified and directed,Make : As Per OEM. |
| 84 | S & F in repair Display control panel (Base card) for 300 to 400 kva DG set complete all as specified and directed, Make : As Per OEM. |
| 85 | S & F in repair Stop solenoid switch 12 Volts complete all as specified and directed . Make As Per OEM |
| 86 | S & F in repair Stop solenoid switch 24 Volts complete all as specified and directed. Make- As Per OEM |
| 87 | S & F in repair Automatic Voltage Regulator fit for 125-250 capacity DG set complete all as specified and directed. Make- As Per OEM |
| 88 | S & F in repair Automatic Voltage Regulator fit for 300-400 capacity DG set complete all as specified and directed. Make- As Per OEM |
| 89 | Calibration of FIP and fuel injector from the authorised dealer including petty repairs to make the FIP and injectors functional for the following capacities ofDG set 300-400KVA (Certificate to this effect that calibration and repair is carried out by authorised delear will be submitted by the contractor) complete all as specified and directed. |
| 90 | Disconnecting the electric connection ofAlternator of capacity 300-400 KVA DG set,taking the accumalator and cleaning the core assemblythrough air blower,heat varnishing with insulating material complete all as specified and directed. |
| 91 | S & F in repair Lub Oil cooler plate complete all as specified and directed,Make- As Per OEM |
| 92 | S & F in repair Lub Oil pressure gauge pipe of required standard size complete all as specified and directed, Make- As Per OEM |
| 93 | S & F in repair Oil spray nozzle assembly complete all as specified and directed, Make- As Per OEM |
| 94 | S & F in repair Piston assembly of 125 - 400 KVA DG Set complete all as specified and directed,Make- As Per OEM |
| 95 | S & F in repair Main Bearing of various sizes for DG set of different capacity complete all as specified and directed, Make- As Per OEM |
| 96 | S & F in repair Water temp switchcomplete all as specified and directed, Make- As Per OEM |
| 97 | S & F in repair of fan key for 125-400 KVA DG set complete all as specified and directed,Make- As Per OEM |
| 98 | S & F in repair of fan assembly for 125-400 KVA DG set complete all as specified and directed,Make- As Per OEM |
| 99 | S & F in repair of Exicitation (CX) unit for 300-400 kva DG set complete all as specified and directed,Make- As Per OEM. |
| 100 | S&F battery terminal cable , copper conductor multi strand, unsheathed, single core25sqmm, 1.5 mtr long each for negative and positive terminal fixed/solder with battery terminal clamp and copper lugs each side of cable sitable for 180 AH Battery (Set of 2 nos.) complete all as specified and directed. |
| 101 | Taking down unserviceable battery and supply and fixing 12 volt, 180 AH battery complete all as specified and directed. |
| 102 | Taking down unserviceable battery and supply and fixing 12 volt, 100 AH battery complete all as specified and directed. |
| 103 | Taking down the unserviceable radiator for 125-160 KVA from engine, transportation to the workshop dismantling the radiator, repair the tank /storage portion incl necessary welding & making leak proof of the tank, cleaning the complete radiator with chemical agent and pumping set incl replacement of defective copper core and assembling the radiator including replacement of all old rusted MS nuts, bolts washers & gasket sets including refixing in to the existing position & onthe engine and testing complete all as specified and directed. |
| 104 | Taking down the unserviceable radiator for 200-400 KVA from engine, transportation to the workshop dismantling the radiator, repair the tank /storage portion incl necessary welding & making leak proof of the tank, cleaning the complete radiator with chemical agent and pumping set incl replacement of defective copper core and assembling the radiator including replacement of all old rusted MS nuts, bolts washers & gasket sets including refixing in to the existing position & onthe engine and testing complete all as specified and directed. |
| 105 | Repair, transporting, taking down and servicing of self starter 12/24 volt dc at authorised service centre including refixing the same and testing complete all as specified and directed. |
| 106 | S & F in repair of indicator lamp (R,Y & B) suitable for AMF panel complete all as specified and directed. |
| 107 | S&F Digital SMPS battery charger 24 volts 20 Amp capacity including Amp meter, Volt Meter, Selector switch, Indicator lamp, fuse unit, rectifier, cord etcand testing complete all specified and directed. |
| 108 | Supply and fixing all in one LED Solar power street light fitting panel plate box of capacity 24 Watt is made with High Efficiency Mono Crystalline Solar PV Module, Lithium Ferro Phosphate battery with in-built BMS technology, High Efficacy LED, MPPT Solar Charge Controller and Aluminium Extruded body, automatically control the dimming and brightness of light, installation includes removal of old unserviceable solar street lights plate boxcomplete all as specified and directed. |
| 109 | Supply and fixing in repair Octagonal Pole 7 metre long, 3 mm thick, 70 mm in top and 130 mm at bottom, conforming to relevant IS/IEC standards. Thickness and other specification of pole shall be as per manufacturer and complete all as specified and directed.Note-. The earth work, foundation, PCC, bolts, nuts etc of pole shall be as per manufacturer guidelines and quoted rate is deemed to be included all as directed. |
| 110 | Materials and Labour for earthingwith galvanised earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (earth pit not less rhan 2.25 m deep below normal ground level) with top edge of plate not less than 1.5 meter below normal ground level, the earth plate surrounded by alternative layer of charcoal dust and salt with thickness of 150 mm to a packed thickness of 150 mm on all sides with and including necessary excavation earth work returing filling in and removal of surplus soil upto 50 mtr including galvanised iron Strip 25x4 mm bolted and reverted to earth plate at one end and connected to continuous GI strip encased in and including 40 mm dia GI medium grade protection pipe, 20 mm dia medium grade watering pipe with all fittings from top edge of earth plate upto 2400 mm above ground level fixed and including 25x 3 mm GI clamp bolts nuts and washer, funnel, wiremesh, PCC (1:3:6)type C1 earthing pit, 75 mm thickRCC cover slab reinforced with 8 mm dia TMT bar 100 c/c both ways complete all as specified and as directed including taking out old unserviceable earthing complete.Note :-(i) If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department. (ii) Testing to be carried out by the contractor, entered in the eath testing register, prepared and to be maintained by the contractor & submited to department. (iii) T&P and testing instrument(Earth tester) to be provided by the contractor at own cost.(iv)Quoted rate shall be deemed to include the cost of GI Strip upto a distance of 7.5 metres from the earth plate. Strip required beyond the length shall be measured and paid separately |
| 111 | S&F GI Strip 32x6mm fixed on wall or buried in ground or any other indicated situation complete all as specified and as directed |
| 112 | NOTES:1.The amount of schedule of credit shall be deducted from the total of this BOQ for arriving at contract sum.2.The rates for RCC/PCC shall deemed to include the cost of formwork, shuttering etc., required for complete and proper execution of the item. Refer Schedule \"A\" notes for details. |
