|
| 1 | Demolition ofreinforced cement concrete such as roofs, floors, slab cover, beams, landing,lintel bendsand similar suspended work including breacking/demolishing by mechanical means such as electric Breaker/Pneumatic Breaker/Hydraulic Breaker as per the site condition/requirementsand removing the debriesOut side the MD Land complete all as specified and as directed. |
| 2 | M&L for RCC 1:2:4 Nominal Mix Type B-1 using 20mm graded stone aggregate as in PillarsColumns, pillars, piers, posts and Gate Pillars comlee all as specified and directed |
| 3 | Providing steel formwork to sides of pillars, posts, struts, piers, columns etc to rough finish surfaces of concrete complete all as specified and directed |
| 4 | M&L for RCC 1:2:4 Nominal Mix Type B-1 using 20mm graded stone aggregate as inBeams, cantilevers, bressummers,lintels over 1.5m span complete all specified and directed |
| 5 | Providing formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, to rough finish surfaces of concrete complete all as specified and directed |
| 6 | M&L for mild steel TMT bars8mm dia and over, cut to length, bent to shape required, including cranking bending spirally for lintels and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, all as specified. |
| 7 | Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed. |
| 8 | M&L precast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slab/drain cover etc or any other similar work set in CM 1:6 including necessary form work complete all as specified and directed. |
| 9 | Dismantling of wrought iron or mild steel work of any description not otherwise provided forcomplete all as specified and directed. |
| 10 | Dismantling of wooden members such as railing/posts/purline/ rafter/oar any other similar wooden components including stacking of serviceable materialscomplete alll as specfied and directed. |
| 11 | Material & Labourfor providing and fixing stainless steel (Grade 304) railing/grills/gates made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement including making hole or cutting through stone/ brick masonry and making good/packing with cement mortar in CM 1:3 complete specified and directed |
| 12 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. |
| 13 | M&L for 18-20 mm thick granite(Black Jet ) work (table rubbed and polished) in steps jambs, pillars, window -cills cooking platforms and like in cement mortal (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, cutting and moulding edges over and including 10 mm thick plaster inCM 1:6 complete all as specified and directed. |
| 14 | S & F in repairs1.25 Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap jointswith riveted or welded seams, including bending or turning up, mitred angles, etc. as requiredComplete all as specified and directed. |
| 15 | Material & Labour for applying two or more (on stishfaction of Engr-in- Charge) coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including complete removal of existing treatment complete all as specified and directed.Note :Bidder shall be considered height of bldgsupto 6 the storey while quotingrates by them andwherever scaffolding is necessary. |
| 16 | Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooksand hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete as specfied and directed. |
| 17 | S&F structural steel Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 -W(Gde- E- 250) quality- A, complete all as specified and directed. |
| 18 | Dismantling of asbestos cement (corrugated or semi corrugated etc) sheet in roof covering complete all as specified and directed |
| 19 | Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 20 | M&L for making holes/perforation of dia exc 50mm but not exc 100mm in existing old or new fixed Galvalume sheet of thikness 0.50mm, including making drilling/cutting using metal cutter/hole saw, deburring sharp edges, fixing rubber grommets(as required) and ensuring propper air-pasages for ventilations/view cutter installation complete all as specified and directed |
| 21 | ditto as per item no 19 but plain sheet as in ridge complete all as specified and directed |
| 22 | M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of newly steel surfaces of any description exc. 10cm width or girth complete all as specified and as directed. |
| 23 | S&F in repair 1.75 to 2.00mm printed/greenPVC sheet fixed or laid on gate/windowby using steel winding wire or any other means complete all as specified and directed by Engr-in-charge. |
| 24 | Demolition of Plain Cement concrete of any description at any positionof anythickness including breacking/demolishing by mechanical means such as electric Breaker/Pneumatic Breaker/Hydraulic Breaker as per the site condition/requirementsand removing the debriesOut side the MD Land complete all as specified and as directed. |
| 25 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed. |
| 26 | M&L for PCC1:2:4 type B-1 using 20mm graded stone aggregate as in post holes complete all as specified anddirected. |
| 27 | M&L for PCC1:4:8 type D-2 (using 40mm graded stone aggregate ) for in base filling or mass concretecomplete as specified and directed. |
| 28 | M & L for 75 mm thick cement concrete type D-2 1:4:8 using 40mm graded aggregate as in sub base to floor finished rough to receive top finishes. complete all as specified and as directed by the Engineer-in-Charge |
| 29 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed . |
| 30 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including allquoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles by mechanical/through labourers complete all as directed . |
| 31 | M & L for brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and as directed. |
| 32 | ditto as per item Sl No 30 but except bricks in CM 1:4 complete all as specfied and directed. |
| 33 | Taking down cement plaster on Brick or Stone,concretewalls ,ceiling etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 34 | M & L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement plaster 1:6, finished even and smooth without using extra cement complete all as specified and directed. |
| 35 | Providing and fixing in repairrectangular/circular/square medium duty(weight capacity 2.5 to 5 ton) composite FRP cover anti corrosivewith frame forstormdrain /inspection chamber/traps/manhole etc having thickness not less than 75mm complete all as specified and directed.Note : Sizeof the slabs shall be as per site requirement. |
| 36 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.e all as specified directed. Note- Size and shape shall be decided by GE. |
| 37 | Cutting holes in brick wallsexc half brickbut n.exc onethick in Cement mortar for inserting Posts/struts/angle Iron/and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required comlete all s specified and directed . |
| 38 | M&L for Providing, cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate), in lintels upto1.5m clear span,cills,steps; seismic and other similar bands, plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering,slightly rounded or chamfered angles and throating,including necessary form work complete all as specified and directed |
| 39 | Supply andfixing Designer OutdoorCeremic wall Tiles of size 300X600mm or 300x450mm and thickness 6-8mm ofapproved shadeand pattern including providing and applying C-2 Grade adhesive having coverage area 3.00-4.00Kg per Sqm,filling the joints of tiles with eppoxy /polymer-modified grout 3-5mm thick including taking down the existing cement plaster/loose materials and applying bonding coats, if required on the direction of Engr-in-Charge/JE-in-Charge conforming IS-15622, Complete all as specified and directed |
| 40 | S&F in repairs Cast iron soil, waste and vent pipes of 75mm in any lengthwith or without ears, with cement joints , fixed to walls all as specified and directed. |
| 41 | S&F in repairs Cast iron soil, waste and vent pipes of 100mm in any lengthwith or without ears, with cement joints , fixed to walls all as specified and directed. |
| 42 | S&F in repairsCast iron Bends of 75mm ( any radius ), diminishing pieces or tapers (larger bore measuared) all as specified and directed. |
| 43 | S&F Cast iron Bends of 100mm ( any radius ), diminishing pieces or tapers (larger bore measuared) all as specified and directed. |
| 44 | Providing and Laying 12-15 mm thick heavy duty Parking Tiles ant-skid,Interlocking/Chekered designe approved colour & Makefor foothpath/parking/lawn tiles of size 300x300 of choice colour fixing over and 20mm thick screed bed in CM 1:6 complete all as specified and directed |
