|
| 1 | M&L for systematically cleaning of blockage of WC Indian / Orrisa / European type/ pattern and bathroom / kitchen including cleaning of Nahani traps/ gully traps/ floor traps by removing of all the mud/ sludge and getting out including cleaning of SGSW or CI pipe upto 1st manhole and depositng the sludge in a pit of suitable size at a distance not exceeding 50 metres from the gully trap and covering the same with the soil obtained from excavation of pit, complete all as specified and directed by Engineer-in-Charge.Notes :- (i) Rates for excavation and earth work shall be deemed to include in the quoted rates. (ii) The contractor or his authorised representative shall collect the complaints of all blockage from complaint cell/ Engr-in-charge daily and all complaints will be rectified by the contractor within same day and returne the complaint slip after completion of complaint and get receipt from concerned JE/Engr-in-charge. If he fails to complete the work within same day then a recovery will be made @ Rs. 50.00 per complaint per day. (iii) The work shall be done in foul conditions and necessary precautionary measures/ equipments to be adopted by the contractor and rates for the same shall be deemed to include in the quoted rates. (iv) Any damage caused during cleaning shall be made good by the contractor to the entire satisfaction of Engr-in-Charge without any extra cost to Govt. |
| 2 | M&L for systematically cleaning of the sewage lines including gully traps by passing ropes, knots, bamboo/ wire/ kandi rotary cleaner etc. for any type and dia of sewage pipe, complete all as specified and as directed by Engr-in-Charge. |
| 3 | Cleaning and desludging of manholes of any size, shape and any depthincluding pumping out liquid waste if any and removing all solid waste materials such as stones, bricks, pipes, plastic muds etc, pluggings/ diverting of flow if required and removing the debries outside MD land etc. including all precautionary and safty measures, complete all as specified and directed by Engineer-in-Charge. |
| 4 | M&L for cleaning, desludging & de-watering of existing septic tanks for 100 users and opening covers and including inlet and outlet chambers and soakage well, taking out sludge & sewage water in any form alongwith all other foreign materials by mechanical equipment or by way of other suitable means and removing waste material/ sludge etc. to outside MD Land including digging, burrying in ground (Qty of desludging/ dewatering taken out not exc 12.0 Cum from each eeptic tank), complete all as specified and directed by Engineer-in-Charge.Notes :- (i) Work shall be done in foul conditions, necessary precautionary measures/ equipments to be adopted by the contractor.(ii) The solid or semi solid sludge shall be burried in pits and fully covered with a layer of lime powder and earth. (iii) Rates quoted by the contractor shall be deemed to have considered all such contingencies including removal and refixing manhole covers. (iv) Any damage caused during cleaning shall be made good by the contractor to the entire satisfaction of Engr-in-Charge without any extra cost to Govt. |
| 5 | All as per serial item No. 4.00 here-in-above but 50 users capacity (desludging not exc 6.0 Cum and dewatering not exc 6.0 Cum from each septic tank). |
| 6 | All as per serial item No. 4.00 here-in-above but 25 users capacity (desludging not exc 4.0 Cum and dewatering not exc 4.0 Cum from each septic tank). |
| 7 | Excavation in trenches, not exc 1.5 mtr wide and not exc 1.5 mtr in depth for foundation, shafts, wells, cesspits, manholes, pier holes etc. and getting out in any type of soil, complete all as specified and directed. |
| 8 | M&L for HDPE DWC (double wall corrugated) pipes, confirming to IS:16098 of 180mm internal dia, presure rating SN-8 fixed with rubber seal and copler required with and including suitable bends 90/60/45 degree etc. single \"Y\" junction, complete as required fixed as per manufacturer\"s instructions, laid in trenches for sewage lines, complete all as specified and directed.Note :- Rates included for taking out old sewage pipe of any type and dia, bends any size and type, Y Jn coupler /adaptor etc. required and net total length of pipe with fittings shall be measured for payment purpose. |
| 9 | M&L for HDPE DWC (double wall corrugated) pipes, confirming to IS:16098 of 150mm internal dia, presure rating SN-8 fixed with rubber seal and copler required with and including suitable bends 90/60/45 degree etc. single \"Y\" junction, complete as required fixed as per manufacturer\"s instructions, laid in trenches for sewage lines, complete all as specified and directed.Note :- Rates included for taking out old sewage pipe of any type and dia, bends any size and type, Y Jn coupler /adaptor etc. required and net total length of pipe with fittings shall be measured for payment purpose. |
| 10 | M&L for 150mm bore reinforced concrete pipes, Class NP2, laid and jointed complete with collars, complete all as specified and directed. |
| 11 | M&L for 200mm bore reinforced concrete pipes, Class NP2, laid and jointed complete with collars, complete all as specified and directed. |
| 12 | M&L for 450mm bore reinforced concrete pipes, Class NP2, laid and jointed complete with collars, complete all as specified and directed. |
| 13 | M&L for cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundation, bed for laying of sewage lines or mass concrete, complete all as specified and directed. |
| 14 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm thick, complete all as specified and directed. |
| 15 | Removing excavated material (soils) to a distance not exce 50 mtr and depositing where directed at level not exc. 1.5 mtr above the starting point, complete all as specified and directed. |
| 16 | Demolition and breaking up drain pipes (salt glazed stoneware, AC or reinforced concrete) of any dia, set in cement mortar, complete all as specified and directed. |
| 17 | Dismantling / taking out of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches/ wall upto & incl of internal dia of pipe 100/75mm, complete all as specified and directed. |
| 18 | M&L for 100mm bore sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, laid in trenches or in floors, complete all as specified and directed. |
| 19 | M&L for 100mm bore sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, fixed to walls with and including MS clamps of suitable size, complete all as specified and directed. |
| 20 | All as per serial item No. 19.00 here-in-above but refixing only (except pipe) with stack clamps etc, complete all as specified and directed. |
| 21 | M&L for 75mm bore sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, fixed to walls with and including MS clamps of suitable size, complete all as specified and directed. |
| 22 | All as per serial item No. 21.00 here-in-above but refixing only (except pipe) with stack clamps etc, complete all as specified and directed. |
| 23 | S&F in replacement of 100mm bore sand cast iron bends/ reducer/ Tee (any radius)with access door, diminishing pieces or tapers (larger bore measured), complete all as specified and directed. |
| 24 | S&F in replacement of 75mm bore sand cast iron bends/ reducer/ Tee (any radius)with access door, diminishing pieces or tapers (larger bore measured), complete all as specified and directed. |
| 25 | S&F in replacement of 100mm bore sand cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and directed. |
| 26 | S&F in replacement of 75mm bore sand cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and directed. |
| 27 | S&F 100mm bore cast iron vent cowl including taking down old vent cowl of any type, complete all as specified and directed. |
| 28 | S&F 75mm bore cast iron vent cowl including taking down old vent cowl of any type, complete all as specified and directed. |
| 29 | Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends swan necks etc. including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories), complete all as specified and directed. |
| 30 | S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed. |
| 31 | S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls with and including stack clamps, nuts and bolts, complete all as specified and directed. |
| 32 | S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed. |
| 33 | S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls with and including stack clamps, nuts and bolts, complete all as specified and directed. |
| 34 | S&F PVC (SWR) bends with access door of any radius of bore 110mm, complete all as specified and directed. |
| 35 | S&F PVC (SWR) bends with access door of any radius of bore 75mm, complete all as specified and directed. |
| 36 | S&F PVC (SWR) branch piece, single (single Y/T) equal or unequal of bore 110mm, complete all as specified and directed. |
| 37 | S&F PVC (SWR) branch piece, single (single Y/T) equal or unequal of bore 75mm, complete all as specified and directed. |
| 38 | Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water including remaval of derbis from site, complete all as specified and directed. |
| 39 | M&L for 15mm thick rendering in CM 1:4 on fair face of brick work or concrete surfaces and finished the surface even and smooth without using extra cement, complete all as specified and directed. |
| 40 | Demolition of brick work or stone masonry, built in cement mortar including all quoines, arches, pillars etc. but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed. |
| 41 | M&L for brick work with sub class ‘B’, old size bricks, straight or curved on plan exc 6 mtr mean radius, built in CM 1:6, complete all as specified and directed. |
| 42 | All as per serial item No. 41.00 here-in-above but except bricks. |
| 43 | M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4, complete all as specified and directed. |
| 44 | All as per serial item No. 43.00 here-in-above but except stones. |
| 45 | M&L for 50mm thick PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in plinth protection, finished the surface even & smooth without using extra cement including making joints 10mm wide and 30mm deep at spacing not more than 2.5m and at corners as mandatory and filled with sealing compound grade A, complete all as specified and directed. |
| 46 | M&L for plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in coping, kerbing etc. including weathering, slightly rounded or chamfered, treading and necessary formwork if required at site, complete all as specified and directed. |
| 47 | M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in surface channel or drain including necessary formwork etc, complete all as specified and directed. |
| 48 | M&L for precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregates) cover slabs for manholes with plain faces, finished fair and smooth and set in CM 1:6, complete all as specified and directed. |
| 49 | Dismantling of wrought iron/ mild steel/ steel works of any description and in any position, complete all as specified and directed. |
| 50 | M&L for mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work, conforming to Fe-290 Gde-E-165, complete all as specified and directed. |
| 51 | Demolition of cement concrete (unreinforced) as in ground floors and pavings, not exe 15cm thickness (below or above ground level), complete all as specified and directed. |
| 52 | Demolition of cement concrete (reinforced) of any description and in any position, not otherwise specifically provided for, complete all as specified and directed. |
| 53 | S&F in replacement of wash down water closet (pedestal pattern) complete with Pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. including PVC seat and cover for pedestal pan, complete all as specified and directed. |
| 54 | S&F in replacement of 10 Ltr PVC valveless syphonic action type flushing cistern low level white with inlet including bracket and 32mm flush pipe of polythylene ball valve,float and handleof low or high density and 15mm PVC connection 450mm long, complete all as specified and directed. |
| 55 | S&F in replacement of wash basin, vitreous china (flat back or angle back type), size 550mm x 400mm with pedestal height 800mm including cutting for and pinning in ends of brackets or erecting stand including CP waste coupling of 32mm dia and PVC waste pipe of 32mm bore, complete all as specified and directed. |
| 56 | S&F in replacement of vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe) but including waste coupling, urinal spreader with PVC connections and waste pipe of suitable size, complete all as specified and directed. |
| 57 | S&F factory made heavy duty full body digital matt finish paving coloured tiles of size 300mm x 300mm x 10mm thick each as in floor for external use, laid over and including 15mm thick screed bed or bedding layer in CM 1:4 including jointed with neat cement slurry and pointed in coloured tile epoxy grout to match the shade of tiles, complete all as specified and directed. |
| 58 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed. |
| 59 | M&L for refixing of interlocking tiles of any thickness, laid dry in position over sand cushioning including dismantling of existing tiles, complete all as specified and directed. |
| 60 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand) including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required, complete all as specified and directed. |
| 61 | M&L for 75mm thick PCC 1:4:8 type D-1 (using 20mm graded crushed stone aggregates) as in sub base, floor etc, complete all as specified and directed. |
| 62 | M&L for treatment of sunken floor surfaces with 0.488 Kg/Sqm first layer of slurry of cement mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer shall be allowed to be cured for 4 hours and then applying in second layer slurry of cement @ 0.242 Kg/Sqm mixed with acrylic based polymer based modified cementitious composite compound @ 0.126 Kg/Sqm. This layer shall be allowed to be cured for 4 hours including taking down old/existing treatment with wire brusing and clearing the dust and foreign material before new treatment and incuding one GI light grade 450mm long 32 mm dia Spout to each sunken floor, complete all as specified and directed. |
| 63 | M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:3, finishing the surface even and smooth w/o using extra cement, complete all as specified and directed. |
| 64 | M&L for lean concrete 1:5:10 type E-2 (using 40mm graded crushed stone aggregates) as in sunken portion treatment, complete all as specified and directed. |
| 65 | S&F in replacement of vitreous china squalting pan, Orissa pattern of size 580mm x 440mm white with integral foot rests, \"P\" or \"S\" trap long body with integral foot rest and fixed with cement concrete bedding, complete all as specified and directed. |
| 66 | M&L for non skid coloured ceramic tiles area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, 7mm to 8mm thick as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 15mm thick screed bed/ plaster in CM 1:4, complete all as specified and directed. |
| 67 | M&L for 10mm thick vitrified ceramic tiles, any colour (square or rectangular), polished, area of each tile not exe 0.36 Sqm as in floors, skirtings etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, fixed over and including 15mm thick screed bed/ plaster in CM 1:4, complete all as specified and directed. |
| 68 | M&L for glazed ceramic coloured digital tiles as on vertical surfaces of wall, skirtings, dados, size of each tile 450mm x 300mm x 7mm thick as approved pattern by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick rendering in CM 1:4, complete all as specified and directed. |
| 69 | M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in floor base of tiles, complete all as specified and directed. |
| 70 | Dismantling floor, hearth or wall tiling including cement mortar bedding complete, removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 71 | M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer, complete all as specified and directed. |
| 72 | S&F in replacement of PVC flexible urinal pipe of 50mm dia 900 long, complete all as specified and directed. |
| 73 | S&F in replacement of PVC flexible waste pipe for wash basin / sink, complete all as specified and directed. |
| 74 | S&F in repairs/ replacement of galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc. complete all as specified and directed.Note :- Each line wire to be measured and paid. |
| 75 | Restraining, resecuring including making good to galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including, securing or tying at crossings with and including provision of galvanised mild steel wire, staples or steel pins etc. complete all as specified and directed.Note :- Each line wire to be measured and paid. |
| 76 | S&F concentina coil punched type (including spike and handle) with 50/51 turns and dia 450/600mm having a 2.6mm dia core wire of high carbon spring steel of high tensile strength. The punched tape and core wore are electrogalvanized to provide protection againist out door exposure. The puched tape is mechanically crimped ove the cover wire and then formed into a coil at various parts of the periphery of the coil steel clips connect the individual turns of the coil to each other so that it open up like an accordion. The weigth of each coil will be 9 Kg (+/-5%) without packing material and coil length wound with bituminious hession cloth of providing protctive coatings, complete all as specified and directed. |
| 77 | Dismantling of fencing wire, chain link, mesh fencing of any type and in any position, complete all as specified and directed. |
| 78 | Fixing only chain link fencing including line wires wearing alternate mesh, any mesh and size and any type to any type of standards, rails, straining bolts etc. including provission of binding wire, complete all as specified and directed. |
| 79 | Supply only chain link MS galvanised fencing of any size and type, complete all as specified and directed. |
| 80 | M&L for mild steel hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars for door, balusters, noising to steps including embedding in concrete and screweing wind ties etc. including securing bolts, post and struts in fencing, drilling holes, notching for wire etc, flat iron fillets including necessary drilling, bolting and reveting etc. or similar works, complete all as specified and directed. |
| 81 | S&F in repair rigid non - metalic PVC casing caping of 25/12mm inclusive of all elbow, tees,etc complete all as per the direction of Engr-in-Charge. |
