|
| 1 | (SH: Construction of DC Bungalow) |
| 2 | Earth Work |
| 3 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.- All kinds of soil. |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre. |
| 5 | Supplying and filling in plinth with sandy soil under floors including watering,ramming, consolidating and dressing complete. |
| 6 | CementConcrete Works |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - 1:4:8 ( 1 Cement: 4coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 8 | FORM WORK |
| 9 | Centering & shuttering including strutting & propping etc.& removal of form for: |
| 10 | a)Foundation, footing, bases of columns etc. and mass concrete |
| 11 | b) Columns, pillars, posts and struts (square rectangular or polygon in plan). |
| 12 | c) Lintels, beams, Plinth beams, girders, bressumers and cantilevers. |
| 13 | d) Suspended floor, roofs, landings, balconies and access platform. |
| 14 | e) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 15 | f)Stairs, (excluding landings) except spiral-staircases. |
| 16 | g)Arches, domes, vaults upto 6m span |
| 17 | RCC WORKS |
| 18 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland Slag cement, admixtures in recommended proportions as per IS:9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength ; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. |
| 19 | i) All works upto Plinth level.a) Concrete of M-25 grade with minimum cement content of 330Kg/cum |
| 20 | ii) All works above Plinth level upto floor V Levela) Concrete of M-25 grade with minimum cement content of 330Kg/cum |
| 21 | Reinforcement for RCC work including straighting,cutting,bending,placing in position and binding all complete. -Thermo-Mechanically Treated bars. |
| 22 | Brick Works |
| 23 | Brick work with first class common burnt clay F.P.S. (non-modular) brick in foundation &plinth in cementmortar 1 : 4 ( 1cement : 4 coarse sand). |
| 24 | Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricksin superstructure above plinth level upto floor V level in - Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 25 | Wood Works |
| 26 | Providing wood work in frames of doors, windows, clerestorywindows andotherframes wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia. And length (hold fast or dash fastener shall be paid for seperately(a) Local best quality Tolhao |
| 27 | (a) Local best quality Tolhao |
| 28 | Providing and fixing panelled or paneled and glazed shutters for doors,windowsand clerestory Windows i/c ISI marked M.S.butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for seperately, all complete as per direction of Engineer-in-charge.(a) Local best qualityTeak wood - 35 mm thick shutters. |
| 29 | Providing and fixing bright finished brass butt hinges withnecessary screws etc. complete :125x85x5.5 mm (heavy type) |
| 30 | Providing and fixing ISI marked oxidised M.S. Tower bolts black finished(barrel type ) with screws etc. complete. |
| 31 | Providing and fixing bright finished steel 100 mm door mortice latch with one dead bolt and a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 32 | Providing and fixing ISI marked oxidised MS handles conforming to IS:4992 with necessary screws etc. complete : a)125mm |
| 33 | Steel Works |
| 34 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. - Fixed to openings /wooden frames with rawl plugs screws etc. |
| 35 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required.10.24.2 In grating, frames, guard bar, railing, brackets, gates and similar works. |
| 36 | Flooring |
| 37 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level : 1:2:4 (1 Cement : 2 Coarse sand : 4 Graded stone aggregate 20mm nominal size) |
| 38 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 39 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement [email protected] kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of sizeSize of Tile 600 x 1200 mm |
| 40 | Marble stone flooring with18mm thick marble stone (sample ofmarble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with : Makrana white second quality |
| 41 | Extra for prefinished nosing to treads of steps of marble stone. |
| 42 | Roofing Works |
| 43 | Providing and laying pressed clay tiles (as per approved pattern 20mm nominal thickness and of approved size) on roofs jointed with cement mortar 1:4 (1Cement : 4 Coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20mm thick cement mortar 1:4 (1 Cement : 4 Coarse Sand) and finish neat complete. |
| 44 | FINISHING WORK |
| 45 | 12 mm cement plaster of mix 1 : 4 (1 cement : 4 coarse sand) |
| 46 | 15 mm cement plaster on rough side of single or half brick wall of mix 1 : 4 (1 cement : 4 coarse sand) |
| 47 | Providing and applying white cement based putty of average thickness 1mm of approved brand manufacture, over the plastered wall surface to prepare the surface even and smooth complete. |
| 48 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer |
| 49 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm. |
| 50 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. i) Two or more coats on new work- |
| 51 | Applying priming coat with ready mixedpink or grey primer of approved brand and manufacture on wood work.(Hard and soft wood). |
| 52 | Providing and applying two coats of fire retardant paint unthinned on cleaned wood/ ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant. |
| 53 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work |
| 54 | Sanitary Installations |
| 55 | Providingand fixing water closet squatting pan (Indian type W.C. pan ) with 100 mmsand cast Iron P or S trap, 10 litre low levelwhiteP.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440 mm with integral type foot rests |
| 56 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 57 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CPBrass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass |
| 58 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 250 mm |
| 59 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 60 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 61 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia |
| 62 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete semi rigid pipe 40 mm |
| 63 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm |
| 64 | Water Supply |
| 65 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. |
| 66 | a) 32 mm dia pipe |
| 67 | b) 50 mm dia pipe |
| 68 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wall etc |
| 69 | a) 25 mm dia pipe |
| 70 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarsesand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 71 | (SH: Construction of Security Barrack) |
| 72 | Earth Work |
| 73 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.- All kinds of soil. |
| 74 | Loose/Soft soil. |
| 75 | Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre. |
| 76 | Supplying and filling in plinth with sandy soil under floors including watering,ramming, consolidating and dressing complete. |
| 77 | Cement concrete works |
| 78 | Providing and laying cement concrete of specified gradeexcluding the cost of centering and footing shuttering- All work upto plinth level: |
| 79 | a) 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size) |
| 80 | Form Works |
| 81 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 82 | a) foundation footings, bases of columns etc. and mass concrete. |
| 83 | b) Columns, pillars, posts and struts (square rectangular or polygon in plan). |
| 84 | c) Lintels, beams, Plinth beams, girders, bressumers and cantilevers. |
| 85 | RCC Works |
| 86 | Providing and laying in position specific grade of reinforced cement concrete,excluding the cost of centerring,shuttering,finishing and reinforcement-All work up to plinth level -1:1.5:3 ( 1 cement :1.5 c/sand: 3 graded stone agro. 20 mm nominal size.) |
| 87 | R.C.C. work in wall(any thickness),including attached pilasters,buttresses,plinth and string courses,fillets,column,pillars,piers,abutments,post and struts etc up to floor five level excluding cost of centering,shuttering,finishing and reinforcementin 1:1.5:3( 1 cement :1.5 course sand: 3graded stone aggrt. 20mm nominal size) |
| 88 | RCC work in beams,suspended floors, roof having slope up to 15 degree landing,balconies, shelves ,chajjas,lintel,bands,plain window sill,staircase and spiral stair cases upto floor five levelexcluding the cost of centering, shuttering and reinforcement.a) 1:1.5:3 (1 cement: 1.5 course sand: 3 graded stone aggt. 20mm nominal size |
| 89 | Reinforcement for RCC work including straighting,cutting,bending,placing in position and binding all complete. -Thermo-Mechanically Treated bars. |
| 90 | Brick Works |
| 91 | Brick work with first class common burnt clay F.P.S. (non-modular) brick in foundation &plinth in cementmortar 1 : 4 ( 1cement : 4 coarse sand). |
| 92 | Half brick with 1st class common burnt clay F.P.S. (non-modular) brick in foundation &plinth in cementmortar 1 : 4 ( 1cement : 4 coarse sand). |
| 93 | Wood Works |
| 94 | Providing wood work in frames of doors, windows, clerestorywindows andotherframes wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia. And length (hold fast or dash fastener shall be paid for seperately(a) Local best quality Teakwood |
| 95 | Providing and fixing panelled or paneled and glazed shutters for doors,windowsand clerestory Windows i/c ISI marked M.S.butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for seperately, all complete as per direction of Engineer-in-charge.(a) Local best qualityTeak wood - 35 mm thick shutters. |
| 96 | Providing and fixing bright finished brass butt hinges withnecessary screws etc. complete :125x85x5.5 mm (heavy type) |
| 97 | Providing and fixing ISI marked oxidised M.S. Tower bolts black finished(barrel type ) with screws etc. complete. |
| 98 | Providing and fixing bright finished steel 100 mm door mortice latch with one dead bolt and a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 99 | Steel Works |
| 100 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 101 | Flooring |
| 102 | Cement concrete flooring 1:2;4 (1 cement : 2 C/Sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete- 40 mm thick with 20mm nominal size stone aggregate. |
| 103 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 104 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement [email protected] kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of sizeSize of Tile 600 x 1200 mm |
| 105 | Roofing Works |
| 106 | Providing and fixing at all height false ceiling including providingand fixing of frame work made of special sections, power pressed from M.S. sheet and galvanised with zinc coating of 120 gms/ sqm (both sided inclusive) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm diax50mm long with 6mm dia bolts,other flange of cleat fixed to the angle hangers of 25x25x0.55mm of required length with nuts and bolts of required size and the other end of the angle hanger fixed with intermediate G.I. channels 45x15x0.9mm running at the spacing of 1200mm centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre, with 25mm long drive-all screws @ 230mminterval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishng toa flush finish of tapered and square edges of the board with recommended jointing compound,jointing tapes, finishing with jointing compund in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board,all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers,cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, and specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I |
| 107 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required withiii) Precoated galvanised iron profile sheets0.50 mm thick |
| 108 | Finishing |
| 109 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand ) finished witha floating coat of neat cement. |
| 110 | Providing and applying white cement based putty of average thickness 1mm of approved brand manufacture, over the plastered wall surface to prepare the surface even and smooth complete. |
| 111 | Applying priming coat with ready mixedpink or grey primer of approved brand and manufacture on wood work.(Hard and soft wood). |
| 112 | Providing and applying two coats of fire retardant paint unthinned on cleaned wood/ ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant. |
| 113 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm. |
| 114 | Sanitary Installations |
| 115 | Providingand fixing water closet squatting pan (Indian type W.C. pan ) with 100 mmsand cast Iron P or S trap, 10 litre low levelwhiteP.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440 mm with integral type foot rests |
| 116 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 117 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CPBrass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass |
| 118 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :510x1040 mm bowl depth 250 mm |
| 119 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 120 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 121 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia |
| 122 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete semi rigid pipe 40 mm |
| 123 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm |
| 124 | Water Supply |
| 125 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. |
| 126 | 32mm dia |
| 127 | 50mm dia |
| 128 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wall etc |
| 129 | 25mm dia |
| 130 | 32mm dia |
| 131 | (SH: Construction of Garage) |
| 132 | Earth Work |
| 133 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.- All kinds of soil. |
| 134 | Loose/Soft soil. |
| 135 | Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre. |
| 136 | Supplying and filling in plinth with sandy soil under floors including watering,ramming, consolidating and dressing complete. |
| 137 | Cement concrete works |
| 138 | Providing and laying cement concrete of specified gradeexcluding the cost of centering and footing shuttering- All work upto plinth level: |
| 139 | 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size) |
| 140 | Form works |
| 141 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 142 | a) foundation footings, bases of columns etc. and mass concrete. |
| 143 | b) Columns, pillars, posts and struts (square rectangular or polygon in plan). |
| 144 | c) Lintels, beams, Plinth beams, girders, bressumers and cantilevers. |
| 145 | RCC Works |
| 146 | Providing and laying in position specific grade of reinforced cement concrete,excluding the cost of centerring,shuttering,finishing and reinforcement-All work up to plinth level -1:1.5:3 ( 1 cement :1.5 c/sand: 3 graded stone agro. 20 mm nominal size.) |
| 147 | R.C.C. work in wall(any thickness),including attached pilasters,buttresses,plinth and string courses,fillets,column,pillars,piers,abutments,post and struts etc up to floor five level excluding cost of centering,shuttering,finishing and reinforcementin 1:1.5:3( 1 cement :1.5 course sand: 3graded stone aggrt. 20mm nominal size) |
| 148 | RCC work in beams,suspended floors, roof having slope up to 15 degree landing,balconies, shelves ,chajjas,lintel,bands,plain window sill,staircase and spiral stair cases upto floor five levelexcluding the cost of centering, shuttering and reinforcement.a) 1:1.5:3 (1 cement: 1.5 course sand: 3 graded stone aggt. 20mm nominal size |
| 149 | Reinforcement for RCC work including straighting,cutting,bending,placing in position and binding all complete. -Thermo-Mechanically Treated bars. |
| 150 | Brick Works |
| 151 | Brick work with first class common burnt clay F.P.S. (non-modular) brick in foundation &plinth in cementmortar 1 : 4 ( 1cement : 4 coarse sand). |
| 152 | Half brick with 1st class common burnt clay F.P.S. (non-modular) brick in foundation &plinth in cementmortar 1 : 4 ( 1cement : 4 coarse sand). |
| 153 | Steel Works |
| 154 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 155 | Flooring |
| 156 | Cement concrete flooring 1:2;4 (1 cement : 2 C/Sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete- 40 mm thick with 20mm nominal size stone aggregate. |
| 157 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement [email protected] kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of sizeSize of Tile 600 x 1200 mm |
| 158 | Roofing Works |
| 159 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required withiii) Precoated galvanised iron profile sheets0.50 mm thick |
| 160 | Finishing |
| 161 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand ) finished witha floating coat of neat cement. |
| 162 | Providing and applying white cement based putty of average thickness 1mm of approved brand manufacture, over the plastered wall surface to prepare the surface even and smooth complete. |
| 163 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm. |
| 164 | (SH: Construction of Security Tower) |
| 165 | Earth Work |
| 166 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.- All kinds of soil. |
| 167 | a) Loose/Soft soil. |
| 168 | Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre. |
| 169 | Cement Concrete Works |
| 170 | Providing and laying cement concrete of specified gradeexcluding the cost of centering and footing shuttering- All work upto plinth level: |
| 171 | a) 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size) |
| 172 | Form works |
| 173 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 174 | a) foundation footings, bases of columns etc. and mass concrete. |
| 175 | b) Columns, pillars, posts and struts (square rectangular or polygon in plan). |
| 176 | c) Lintels, beams, Plinth beams, girders, bressumers and cantilevers. |
| 177 | d) Suspended floor, roofs, landings, balconies and access platform. |
| 178 | RCC Works |
| 179 | Providing and laying in position specific grade of reinforced cement concrete,excluding the cost of centerring,shuttering,finishing and reinforcement-All work up to plinth level -1:1.5:3 ( 1 cement :1.5 c/sand: 3 graded stone agro. 20 mm nominal size.) |
| 180 | R.C.C. work in wall(any thickness),including attached pilasters,buttresses,plinth and string courses,fillets,column,pillars,piers,abutments,post and struts etc up to floor five level excluding cost of centering,shuttering,finishing and reinforcementin 1:1.5:3( 1 cement :1.5 course sand: 3graded stone aggrt. 20mm nominal size) |
| 181 | RCC work in beams,suspended floors, roof having slope up to 15 degree landing,balconies, shelves ,chajjas,lintel,bands,plain window sill,staircase and spiral stair cases upto floor five levelexcluding the cost of centering, shuttering and reinforcement.a) 1:1.5:3 (1 cement: 1.5 course sand: 3 graded stone aggt. 20mm nominal size |
| 182 | Reinforcement for RCC work including straighting,cutting,bending,placing in position and binding all complete. -Thermo-Mechanically Treated bars. |
| 183 | Brick Works |
| 184 | Half brick with 1st class common burnt clay F.P.S. (non-modular) brick in foundation &plinth in cementmortar 1 : 4 ( 1cement : 4 coarse sand). |
| 185 | Steel Works |
| 186 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 187 | Roofing Works |
| 188 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required withiii) Precoated galvanised iron profile sheets0.50 mm thick |
| 189 | Finishing |
| 190 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand ) finished witha floating coat of neat cement. |
| 191 | Providing and applying white cement based putty of average thickness 1mm of approved brand manufacture, over the plastered wall surface to prepare the surface even and smooth complete. |
| 192 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm. |
| 193 | (SH: Construction of Approach and Courtyard for Paver Block) |
| 194 | Hill Cutting |
| 195 | Excavation in Hilly Area Soil with Dozer with lead upto 1000 metres (Excavation for road way in soil by mechanical means including cutting and transporting the earth to site of embanment/dumping area with lead upto 1000 metres including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections) |
| 196 | Road Work |
| 197 | Providing, laying and compacting granular base / sub-base according to lines, grades and cross sections by using naturally occurred sand gravel/conforming to IRC-Grd-II of MOST specification free from organic or other deleterious constituent spread with motor grader and compacted by rolling with power roller of 8-10 capacity in layers not exceeding 150mm (spread thickness) i/c rolling of the road surface to proper level and grades 30 cm width edging on both side etc. complete as directed by Engineer-in-charge. |
| 198 | Cable duct across the road (provding and laying of a rcc pipe duct, 300 mm dia across the road (new constructon), extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm iin case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher tha ground level to prevent entry of water and dirt, all as per IRC: 98- 1997 and approved drawings.) |
| 199 | Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. |
| 200 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and technical Specifications (F) PCC Grade M30 using batching plant & Manual placing |
| 201 | Providing and laying factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. i) 80mm thick |
| 202 | (SH:- Construction of Protection Wall and Line drain) |
| 203 | Protection Wall |
| 204 | Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilizing the remaining earth locally for road work.) (i) Ordinary soil B) Mechanical Means (Depth upto 3 m) |
| 205 | PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 mix with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.) |
| 206 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications (ii) PCC Grade M15 using M15 batching plant & manual placing |
| 207 | Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia , extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specifications |
| 208 | Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification |
| 209 | (a) Granular materials |
| 210 | Line Drain |
| 211 | Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilizing the remaining earth locally for road work.) B) Mechanical Means (Depth upto 3 m) |
| 212 | PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 mix with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.) |
| 213 | Plain/Reinforced cement concrete in Open foundation complete as per drawing and Technical Specifications (i) PCC Grade M15 using batching plant & Concrete pump |
