|
| 1 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm DSR. 15.23.1, |
| 2 | Providing and laying Vitrified tiles in floor in different size (thi ckness to be specifies by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of size Size of Tile 800x800 mm. DSR No-11.41A.2.3, |
| 3 | Providing Corrugated G.S. Sheet roofing including Vertical /Curved Surface Fixed with polymer Coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers filled with white Lead, including a Coat of approved Steel Primer and Two coats of approved Paint on Overlapping of Sheets Complete (UP to any Pitch in horizontal /Vertical or Curved Surface), excluding the Cost of Purlins, rafters and and trusses and including cutting to size and shape wherever required. (1.00 mm thick with Zinc Coating not less than 275 gm/m²) DSR N0-12.1.1, |
| 4 | Structual Steel work riveted bolted or welded in built up section, trusses, Builds up gates, framed work lncluding cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR N0-10.2, |
| 5 | Providing and laying Rectifited Glazed Ceramic floor tiles of Size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with Grey cement Slurry @3.3kg/Sqm including Grouting the Joints with and matching pigment etc., complete. (DSR-11.40), |
| 6 | Providing and fixing Ist quality Ceramic Glazed Wall tiles Conforming to IS :15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Size-300x450 mm, (DSR-8.31), |
| 7 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes. DSR No. 18.8.2, |
| 8 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931, 15 mm nominal bore DSR No. 18.53.1 |
| 9 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore DSR No. 18.51.1 |
| 10 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore DSR No.18.49.1 |
| 11 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. DSR 17.16A, |
| 12 | Providing and fixing C.P. Brass Stop cock (Concealed) Standerd desingn and approved make conforming to IS:8931. 15 mm nominal bore ( 18.52.1) |
| 13 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter. DSR 18.22.2, |
| 14 | Providing and fixing wash besin with C.I. brackets, 15 mm C.P. pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash Besin Size 630x450 mm with a pair of 15 mm C.P. brass pillar tap. DSR No. 17.7.1, |
| 15 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. DSR No. 17.8, |
| 16 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass of approved quality complete with 6 mm thick hard board groung fixed to wooden cleats with C.P. brass screws and washers complete.17.31, |
| 17 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. DSR 17.33, |
| 18 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms. DSR 18.65, |
| 19 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. DSR.No. 17.1.1, |
| 20 | Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend. DSR No. 17.68.1 |
| 21 | Providing and placing on terrace ( at all floor levels ) Polyethylene Water Storage Tank. IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for intel, outlet and overflow pipes but without fittings and the base support for tank. DSR- 18.48), |
| 22 | Providing and fixing gun metal gate valve with C.I heel of approved quality (screwed end) 20 mm dia nominal bore, DSR No. 18.17.1A, |
| 23 | Providing and fixing Ball valve brass of approved quality high or low pressure with plastic floats complet 20 mm nominal bore DSR- 18.18.2, |
| 24 | Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer-in-charge. (DSR No-16.64) |
| 25 | Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. DSR No. 16.68, |
| 26 | 12mm. Thick plaster with cement mortar in proportion of 1:4 cement & coarse sand DSR No. 13.4.1 |
| 27 | Removing white or colour wash by scrapping andsand papering and preparing the surface smooth including necessary repairs to scratches etc. complete DSR N0 13.88, |
| 28 | Providing and Applying white Cement based Putty of average thickness 1 mm. of approved brand and manufacture. Over the Plastered wall Surface to Prepare the Surface even and Smooth Complete. DSR N0-13.80 |
| 29 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade Old work (Two or more coats applied @1.43 ltr/10sqm) over existing cement paint surface (apex Ultima, weather coat All guard). (DSR N0. 13.112.1), |
| 30 | Painting with synthetic enamal paint of approved brand and manufactorar of required colour to give an evan shade Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture DSR No. 13.62.1 Please Enable Macros to View BoQ information |
