|
| 1 | Part A: Civil Works (1 to 81)Earth work in excavation of the foundation tranches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing spreading or stacking the spoils within a lead of 75Mtr as directed. The Item including necessary trimming the sides of tranches, levelling, dressing and ramming the bottom, bailing out water etc. as required complete. Depth of excavation not exceeding 1500 mm. |
| 2 | Earth work in filling in foundation trenches or plinth with good earth obtained from excavation of foundation in layers not exceeding 150mm including watering and ramming etc. layer by layer complete. (Payment to be Made on the basis of the Measurement of finished quantity of work). With earth obtained from excavation of foundation. |
| 3 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.In ground floor including roof. |
| 4 | Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. upto 150 mm. thickIn ground floor including roof. |
| 5 | Dismantle R.C. floor, roof beams etc. including cutting rods and removingrubbish as directed within a lead of 75 Mtr including stacking of steel bars in ground floor including roof. |
| 6 | Dismantling artificial stone flooring upto 50 mm. thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m.In ground floor including roof. |
| 7 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 8 | Taking out Mirzapur or glazed porcelain tiles carefully by chiselling from walls or floor including stacking serviceable material as directed. |
| 9 | Taking out M.S. or W.I. Grills from wooden frame including cutting lugs from masonry wall and refitting the same and mending good damages after repairs. (Excluding the cost of necessary repair of damages) or doing any other necessary works. |
| 10 | Taking out old damaged tarfelt from the roof, parapet etc. preparing the roof surfaces by removing all spoils, blisters, moss etc. from the working site and disposal of the same beyond the compound and cleaning the site in all respect as per direction of Engineer-in-Charge. All floor |
| 11 | Spot application for insecticides using Aqua base spray for pest (for bugs, cockroaches, silverfish, spider, termites, mosquitoes) to walls and ceiling etc. with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying the emulsified chemical @ 0.5 litres per sq.m. by a hand operated pressure pump on wall surfaces, ceiling, electrical fixture, electrical lines including drilling holes inplaces where source of termite is detected squirting chemical solution into the holes and sealing the holes with cement grout. (Rate is per sq.m. of the floor area while actual work will be all walls ceiling, rack, partition and furniture). |
| 12 | Repairing crack in wall by cement grouting (1 : 2) including widening the crack on the surface (into V section) cleaning and packing the same with cement mortar (1 : 2) and finishing off to match with adjacent surface. (Cement-69 Kg/100 m) |
| 13 | Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed. |
| 14 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 15 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 16 | Brick work with 1st class bricks in cement mortar (1:6)In foundation and plinth |
| 17 | Brick work with 1st class bricks in cement mortar (1:6)In superstructure, ground floor. |
| 18 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4). In ground floor. |
| 19 | Provide and lay 25 mm. thick artificial stone in floor dado, staircase etc. with cement concrete (4:2:1) with stone chips with 3 mm. thick topping Made with ordinary/ white cement (as necessary) Marble dust in proportion (2:1) including smooth finishing and rounding of corners and including application of cement slurry before flooring works using cement @ 1.75 kg. / sq. Mtr. all complete including all Materials and labour. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement).Using grey cement in ground floor |
| 20 | Ordinary Cement concrete (mix 1:2:4)with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.Pakur Variet |
| 21 | Ordinary Cement concrete (mix 1:1.5:3)with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.Pakur Variety |
| 22 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes. Pakur variety |
| 23 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work. |
| 24 | 25 mm to 30 mm shuttering without staging in foundation |
| 25 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation and upto roof of ground floor/upto 4Mtr. Tor steel/Mild steel. Other Manufacturer not Specified |
| 26 | M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-in-charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1956 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc.Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof.For structural members of spefied sections weighingless than 22.5 kg/m. |
| 27 | M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete.Payment to be made on the basis of calculated weight of structural memebrs of MS Holow Section as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a hight of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof.For roof truss works. Span up to 12 Mtr. |
| 28 | Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame and refixing the same including mending good all damages complete. (Concrete and brick work for mending damage will be paid separately)Upto area 2.5 Sqm. |
| 29 | Taking out door and window shutters and rehanging the same with old fittings. With new iron screws. |
| 30 | Take out shutter of door and window dismantling by parts (for repair or replacement of damaged parts) reassembling and refitting and rehanging same with old fittings but with new screws as necessary. |
| 31 | Easing door and windows. |
| 32 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M. S. clamps. (The quantum should be corrected upto three decimals).Sal: Malayasian. |
| 33 | Panel shutters of doors and windows as per design (each panel consisting ofsingle plank without joint including fitting and fixing the same in position but excluding the cost of hinge etc. and other fittings. In Ground floor35 mm thick shutters with 19 mm thick panel of size 30 to 45 cm. Sishu, Gammar, Champ, Badam, Bhola, Mogra, Hallak(In case of non-supply of single plank, penal rate of reduction of 20% will be made) |
| 34 | Styles and rails of wooden shutters fitted and fixed complete. (Payment to be made on area of new work only). In Ground Floor: For 35mm Thick shutter. Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak. |
| 35 | Panel (made of single plank) of door and window shutters to design as directed. (Payment to be made on area of exposed new work). (In case of non-supply of single plank penal rate of reduction to a maximum of 30% will be made).19mm thick panel of 30cm to 45cm width. Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak. |
| 36 | Shutters of 2/3rd panel and 1/3rd glazed of doors and windows as per design (each panel consisting of a single plank without joint and with ordinary glass of 7.4kg. Per sq.m./3mm thick) fitted with putty bed and teak wood beads and nails including fitting and fixing shutters in position but excluding the cost of glass, putty, teak bead, nails, hinges etc. and other fittings, in ground floor. 35mm thick shutters with 19mm thick panel. Sishu, Gammar, Champ, Badam, Bhola, Mogra, Hallak |
| 37 | Iron butt hinges of approved quality fitted and fixed with steel screws, with I.S.I. Mark. 75 mm. x 60 mm. x 3.15 mm. |
| 38 | 100 mm. x 75 mm. x 3.50 mm. |
| 39 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: 100mm long x 10mm dia. Bolt |
| 40 | 150 mm. long x 10mm. dia. bolt. |
| 41 | Supplying \"Godrej\" mortice lock chromium plated with keys 6 levers including fitting & fixing complete. |
| 42 | Godrej Hydraulic door closer fitted and fixed complete. Medium type. |
| 43 | Door stopper (Anodised aluminium) |
| 44 | Supplying anodised aluminium catch hook with eye fitted and fixed to shutter and chowkat complete of best quality: 225mm long |
| 45 | Anodised aluminiumAldrop/Slidingbolts ofapproved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete. 250mm x 16mm dia bolt. |
| 46 | AnodisedaliminiumD-typehandleofapprovedquality manufacturedfromextrudedsectionconformingtoI.S. specification (I.S. 230/72) fitted and fixed complete:With continuous plate base (Hexagonal/ Round rod). 125 mm grip x 10 mm dia rod. |
| 47 | Iron door ring of approved quality fitted and fixed with nut and washer complete. 50mm dia. |
| 48 | Supplying, fitting and fixing M.S. clamp for door and window frame made of 40 mm. x 6 mm., 125 mm length flat bent bar, end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction (cost of cement concrete will be paid separately). |
| 49 | Priming one coaton steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.(This item is applicable to new work or old work when the original surface has been exposed by removal of old paint.) |
| 50 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.(This item is applicable to new work or old work when the original surface has been exposed by removal of old paint.) |
| 51 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : On steel or other metal surface : With super gloss (hi-gloss) - Two coats (with any shade except white) |
| 52 | On timber or plastered surface : With super gloss (hi - gloss) - Two coats(with any shade except white). |
| 53 | Plaster ( to wall, floor, ceiling etc. ) with sand and cement morterincluding rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary ( Ground floor). [Excluding cost ofchipping over concrete surface.] With 1:6 cement mortar 20 mm thick plaster. |
| 54 | With 1:6 cement mortar 15 mm. thick plaster . |
| 55 | With 1:4 cement mortar 10 mm thick plaster. |
| 56 | Neat cement punning about 1.5 mmthick in wall, dado, window sill, floor, etc.Note: cement 0.152 Per Cum per 100 sq. Mtr. |
| 57 | M.S. or W.I. ornamental grill of approved design, joints continuously welded with M.S. W.I. flats and bars for windows railing etc. fitted and fixed with necessary screws and lugs.. Grill weighing above 10 kg/sq. m. and up to 16 Kg. / Sq. m. The weight of grill per sq. m. will be determined by taking the physical weight of fabricated grill and dividing the same by covered area of the same. No shop priming will be allowed to facilitate inspection of workmanship. Weight of grill is to be taken after final grinding and finishing the weld. In ground floor.(Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25% for each addl. floor above 4th floor) |
| 58 | Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodised conforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window withfixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge.10-12 Micron thickness Annodizing filmNatural white |
| 59 | Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall). 3 mm thick (weighing 7.4 kg/Sq.m) |
| 60 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.5mm thick coloured / tinted / smoke glass. |
| 61 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.. Area of each tile above 0.09 Sq.mColoured decorative In Ground floor |
| 62 | Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. Area of each tile above 0.09 Sq.mColoured decorative In ground floor. |
| 63 | Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brandconforming to IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.) ≤ 0.08 %] in floor, skirting etc. set in 20 mm thick sand cement mortar (1:4) bed prepared after application of slurry using 1.75Kg of cement per Sqm over the base and 2mm thick cement slurry using cement @2.91Kg./sqm at the back side of the tiles and laid over the mortar bed using 0.2 kg/sqm of White cement used for joint filling with approved pigment as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,Iabour and all other incidental charges complete true to the manufacturer\"s specification and direction of Engineer-in-Charge. ln Ground FIoor:(size not Iess than 600mmX 600 mm X 9.5 mm thick) |
| 64 | Supplying & laying 20 mm designer chequered tiles of any shade and of approved quality as per IS: 1237: 1980 laid in patterns as directed in pavement, footpath including necessary underlay 25 mm thick average cement mortar (1:3) complete in all respect with all labour and materials [using cement slurry @ 4.4 kg/Sq.m at back side of tiles. Cement of mortar & slurry will be supplied by the Department. Border concrete if necessary to be paid separately]. |
| 65 | Supplying and Laying in the specified pattern of Interlocking Concrete Block Pavements (ICBP) with concrete blocks (with Concrete grade as specified as per Table 1 of IS 15658: 2006) manufactured in steel mould clamped to a vibrating table by hydraulic pressure (as per cl. no. 6.30 of IRC: SP: 63 (2018), from BIS license manufacturer, with spacer nib (Small protruding profiles on the vertical faceof a paver block used as a device for keeping minimum joint gap in between the paving block, as per Cl. No. 3.26 of IS: 15658) and of specified size and shape withaspect ratio (The ratio of length to thickness of a paver block, as per Cl. No. 3.3 of IS: 15658) as per Table 2 of IS : 15658 with flexural strength/breaking load as per Annexure G of IS:15658, on the prepared base course of specified CBR as per Table 1 of IRC SP 63 (2018) or else as mentioned in design and drawing with a cushion of compacted bedding sand of 23-35mm thick (grading of the bedding sand as per clause 6.5.1 of IRC SP-63) and filling up the gaps in between paver blocks with joint filling sand (the grading of the joint filling sand will be as per clause 6.5.2 of IRC SP 63) and completing the edges with cut blocks as per Cl.No. 8.7 of IRC SP – 63(2018) with proper confinement of bedding and joint filling sand, compaction, levelling and filling up of the edge gap. 80 mm thickGrey. |
| 66 | Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick). |
| 67 | Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge) |
| 68 | Removing old scales, blisters, etc. of interior surface of walls, ceiling by scraping, etc. and preparing smooth and even surface with rendering of cement mortar (1:2) (as necessary), to make the surface suitable receiving distemper as per direction of the Engineer at site. |
| 69 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. In Ground Floor: One Coat |
| 70 | Add extra for liftingFor 1st Floor level |
| 71 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. Two Coats, Premium 100% Acrylic Emulsion |
| 72 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. (In Ground Floor)One Coat. Water based interior grade Acrylic Primer |
| 73 | Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : Two coats, Standard Quality |
| 74 | Acrylic Distemperto interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specification) including cleaning and smoothning of surface.Two Coats |
| 75 | Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). In Roof, with 0.5 mm thick sheet. |
| 76 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamp nails, including Making holes in walls, floor etc. cutting trenches in any soil through Masonry concrete structures etc if necessary and mending good damages including joining with jointing Materials (Spun Yarn, Valamoid/bitumen/M-Seal etc) complete.UPVC Pipes:110 mm. Dia |
| 77 | Bend 87.5 degree 110 mm. Dia. |
| 78 | Shoe. 110 mm. Dia. |
| 79 | Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria. 66mm x 70mm |
| 80 | Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria.In ground floor. 25 mm thick |
| 81 | Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. [excluding the cost of supporting frame work and teak wood batten/Lipping]In Ground Floor. 12 mm |
| 82 | 19 mm |
| 83 | Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-incharge. The rate includes the cost of labour, adhesive and all incidental charges thereof. Glossy/Matt/Suede excluding surface texture or metallic lustre. Thickness of laminate 1 mmIn ground floor |
| 84 | Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within manufacturer\"s specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface). Note: Applicable only when the full diameter of reinforcement steel is exposed. |
| 85 | Provide and apply shrinkage controlled polymer modified fibre reinforced cementitious repair mortar like Renderoc SP40 of Fosroc or equivalent up to 12 mm thickness by hand or spray application as per specification. |
| 86 | Applying two coats of a two component acrylic polymer-modified cementitious high performance coating (SmartCare Damp Block 2K by Asian Paints or similar material ) on wall by brush or roller and necessary tools and tackles over SSD masonry/brick surface.Allow the 1st coat to dry for 4-6 hrs (drying depends on ambient temperature) and then apply 2nd coat.The 1st coat & 2nd coat must be applied in perpendicular direction.Achieve a coverage of 15 sq.ft./kg/coat. all complete as per direction of the Engineer-in-charge. |
| 87 | Supplying & laying 3mm thick pre-fabricated plastomeric water proofing membrane conforming to EN 12311-1 & ASTMD 5147, manufactured with atactic poly propylene(APP) modified premium grade asphalt , specially reinforced with non-woven polyester core with polyester reinforcement @160 gms per sqm & both faces covered with thermo-fusible polyethylene film /MineraL on top face over a coat of primer @ 0.40 lit/sqm of manufacturer\"s specification on smooth, clean dry surface prepared wherever required. Lap joint shall be provided of 75 mm in longitudinal & 100 mm in transverse direction and fused using LPG/ Propane torch employing extra care ensuring full bondage, complete removal of entrapped air and sealing edges into grooves in appropriate manner as per direction of Engineer -in-charge all complete including materials,labour and applicable taxes. (Payment shall be made on the basis of finished surface area.).Membrane Property: Softening Point > 150 deg C, ColdFlexibility < -6 deg C, Tensile Strength, N/cm : 600(longitudinal), 450 (transverse), Tearing Strength, N:300 (longitudinal), 200 (transverse) |
| 88 | Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both faces of M.S./ W.I. gate etc. with point welding at not more than 150mm apart complete in all respect as per design including cost of all labour and materials. |
| 89 | Cutting / cleaning / removing jungles, including uprooting / removing of rank vegetation, cutting gran, bush wood cutting gran, bush wood cutting / removing small tree saplings or branches of trees falling under the cutting area at different area of dock and removing spoil up to a distance of 50 m outside the periphery of the area cleared as per direction including all lead, lifts cutting. Instrument, labour etc. complete in all respect |
| 90 | Uprooting and removing plants from the surface of walls parapet etc and making good damages. (Repairing ofdamages to be paid separately). Small plant of girth of exposed stem upto 75 mm. lift upto 6 mtr. |
| 91 | Medium size plant of girth of exposed stem above 75 mm. but not exceeding 150 mm. lift upto 6 mtr. |
| 92 | Cutting of branches of trees and shrubs from the road way or with in R.O.W including disposal of wood and leaves to suitable location as per technical specification Clause 1914 for Rural Roads of MORD. |
| 93 | Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading intotruck and cleaning the site in all respect as per direction of Engineer in charge |
| 94 | Supply of unskilled labours for non-measurable works at Fraserganj. |
| 95 | Part B Plumbing Works: (Item No. 82 to 119)Labour for dismantling G.I. pipe with fittings. 25 mm |
| 96 | 40 mm |
| 97 | Refixing G.I. pipe with fittings after cleaning where necessary. 25 mm |
| 98 | 40 mm |
| 99 | Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. For Concealed Work. CPVC Pipes 15 mm dia. Class-1,SDR-11. |
| 100 | Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I).P.V.C. Pipes 15mm dia. |
| 101 | 20mm dia. |
| 102 | 25mm dia. |
| 103 | 40 mm dia. |
| 104 | Labour for fitting and fixing high density poly-ethylene pipes or P.V.C. pipes for above ground work including cost of jointing materials paints etc. fitting and fixing all necessary specials, cutting pipes, making threads, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps(any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge. (Payment will be made on centre line measurement of the total pipeline including specials).Above Ground15 mm dia. |
| 105 | 20mm dia. |
| 106 | 25 mm dia. |
| 107 | 40 mm dia. |
| 108 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992.UPVC pipes (B Type)Single Socketed 3 Meter Length 110 mm |
| 109 | Double Socketed 3 Meter Length 110 mm |
| 110 | Single Socketed 1.8 Meter Length 110 mm |
| 111 | Double Socketed 1.8 Meter Length 110 mm |
| 112 | Double Socketed 0.9 Meter Length 110 mm |
| 113 | Double Socketed 0.60 Meter Length 110 mm |
| 114 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992FittingsCoupler 110 mm. |
| 115 | Door Tee 110 mm |
| 116 | Bend 87.5º 110 mm |
| 117 | Door Bend (T.S.) 110 mm |
| 118 | Vent Cowl 110 mm |
| 119 | Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineerin-charge. (Payment will be made on centre line measurement of the total pipeline including specials).110 mm dia |
| 120 | Dismantling H.C.I. pipe with fittings including melting lead caulked joints. 100 mm dia |
| 121 | Dismantling wash basin with brackets with or without waste fittings |
| 122 | Dismantling E.P. or Anglo-Indian W.C. |
| 123 | Supplying, fitting and fixing bib cock or stop cock.Chromium plated angular Stop Cock with wall flange (Equivalentto Code No. 5053 & Model - Florentine of Jaquar or similar brand). |
| 124 | Supplying, fitting and fixing pillar cock of approved make.CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model -Tropical / Sumthing Special of ESSCO or similar brand). |
| 125 | CP Wall Mixture without spout but with provision for connnection to Telephone Shower and exposed pipe for Overhead shower (Equivalent to Code No. 5215 & Model - FLORENTINE of JAQUAR or similar brand). |
| 126 | CP 2-way bib Cock - 15 mm, supplied, fitted and fixed. (Code No.5041 & Model - FLORENTINE of JAQUAR or similar brand). |
| 127 | Supplying, fitting and fixing bib cock or stop cock.Chromium plated Bib Cock long body with wall flange with aerator (Equivalent to Code No. 512 & Model - Tropical / Sumthing Special of ESSCO or similar brand) |
| 128 | Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 129 | Chromium plated Stop Cock (Equivalent to Code No. 513(A) &513(B) & Model - Tropical / Sumthing Special of ESSCO or similar brand. |
| 130 | PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent)15 mm |
| 131 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing). 580mm X 440 mm |
| 132 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. With \"P\" trap |
| 133 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. E.W.C. Plastic (hallow type) white. |
| 134 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 135 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. Polythene Flush Pipe each 155.00 |
| 136 | Supplying, fitting and fixing shower of approved brand and make.Chromium plated shower arm 240 mm long (Equivalent to Code No. 536(A) & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 137 | Chromium plated round shower with revolving joint (Equivalent toCode No. 541(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 138 | Supplying,fitting and fixing over head 450 mm long 20 mm dia and 90 ° bend shower arm with flange of Jaquar make (model - SHA-479L450) or equivalent. |
| 139 | Chromium plated overhead Rain shower (Square), size-180x180mm with revolving joint (Model Code No. F7010501 of CERA or equivalent). |
| 140 | Supplying, fitting and fixing PTMT Smart Shelf of approved make of size 300 mm. |
| 141 | Supplying, fitting and fixing towel rail with two brackets. C.P. over brass. 25 mm dia. and 600 mm long |
| 142 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm |
| 143 | Supplying, fitting and fixing 100 mm C.I. round grating. |
| 144 | Supplying, fitting and fixing Peet\"s valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.).40 mm |
| 145 | 25mm. |
| 146 | 20 mm |
| 147 | Supplying, fitting and fixing 550 mm X 400 mm size white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillarcock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. |
| 148 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. 450 mm Long |
| 149 | 600 mm long |
| 150 | Hand Shower(Health Faucet) with 1mtr Fexible Tube with Wall Hook(Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar). |
| 151 | Removing sludge from septic tank, soak well etc. by methor labour including disposal of the same outside the compound as directed.Upto 50 users:-Within a lead of 150 metre |
| 152 | Cleaning soak pit by removing the top slab and replacing inner filling with jhama bats and repairing the pit as necessary including fitting the slab. |
| 153 | Cleaning silt of inspection pit. |
| 154 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75mm X 75 mm X 75 mm wooden blocks complete.470 mm X 280 mm X 340 mm |
| 155 | Cleaning and disinfecting upto 2000 litre Water Tank including masonry reservoir. |
| 156 | Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets. Sink only 530 mm X 430 mm x 180 mm. |
| 157 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer. 2000 litre capacity |
| 158 | Labour for hoisting plastic water storage tank. Above 1500 litre upto 5000 litre capacity. Upto 1st story from G.L. |
| 159 | Extra for each additional story |
| 160 | Labour for punching hole in plastic water storage tank upto 50 mm dia. |
| 161 | Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. With Pakur variety. (JSW/JSPL/SHYAM/SRMB/BMASL/ELLECTROSSTEEL/SSL) |
