|
| 1 | Construction of sub grade and earthern shoulders with approved material obtained from borrow pits with all lifts and leads transporting to sites, spreading, grading to required slope and compacted to meet requirement of table 300.2 including all material, labour, T&P etc complete but excluding GST. |
| 2 | Construction of sub grade and earthern shoulders with approved material obtained from borrow pits with all lifts and leads transporting to sites, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1 including all material, labour, T&P etc complete but excluding GST. |
| 3 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method, with rotavator at O.M.C. and compacting with smooth wheeld roller to achieve the desired density, complete as per Technical Specification clause 401. including all material, labour, T&P etc complete but excluding GST. |
| 4 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness hand packing rolling with smooth wheel roller 80-100 Kn in stages to proper grade and camber applying and brooming stone screening / binding material to fill up the interstics of coarse aggregate, watering and compacting to the required dencity . Grading 2 as per technical specification clause 405 including all material, labour, T&P etc complete but excluding GST. |
| 5 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness hand packing rolling with smooth wheel roller 80-100 Kn in stages to proper grade and camber applying and brooming stone screening / binding material to fill up the interstics of coarse aggregate, watering and compacting to the required dencity Grading 3 as per technical specification clause 405 including all material, labour, T&P etc complete but excluding GST. |
| 6 | Providing and applying Tack coat with bitumen VG-10 using Bitumen pressure distributer @ 0.30 kg. per sqm on the prepared dry and hungry bitumenious surface cleaned with Hydraulic broom as per Technical specification Clause 503. including all material, labour, T&P etc complete but excluding GST. |
| 7 | Providing, laying and rolling of open graded P.C. of 20mm thickness composed of 13.2mm to 5.6mm aggregates eigher using penetration grade bitumen or emulsion to required line grade and level to serve as wearing course on a previously prepared base i/c mixing in a suitable plant, laying and rolling with a three wheeld 80-100 kN static roller capacity, finished to required level and gredes to be followed by seal coat of eigher Type C as per Technical Specification Clause 508 including all material, labour, T&P etc complete but excluding GST. |
| 8 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Technical Specification Clause 510 including all material, labour, T&P etc complete but excluding GST. |
| 9 | Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 including all material, labour, T&P etc complete but excluding GST. |
| 10 | Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections. including all material, labour, T&P etc complete but excluding GST. |
| 11 | Providing concrete for plain/reinforced concrete (M-10) in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 including all material, labour, T&P etc complete but excluding GST. |
| 12 | Brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications Clauses 600, 900 and 1208.4 including all material, labour, T&P etc complete but excluding GST. |
| 13 | Pointing with cement mortar (1:3) on brickwork as per drawing and technical specification Clauses 613.3 and 1204 including all material, labour, T&P etc complete but excluding GST. |
| 14 | Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. including all material, labour, T&P etc complete but excluding GST. |
| 15 | Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 including all material, labour, T&P etc complete but excluding GST. |
| 16 | Providing and laying reinforced cement concrete (M-20) in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 including all material, labour, T&P etc complete but excluding GST. |
| 17 | Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202 including all material, labour, T&P etc complete but excluding GST. Please Enable Macros to View BoQ information |
