|
| 1 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etccomplete all as specified and as directed by the Engineer-in-Charge. |
| 2 | Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly(boxesshall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally) including provision of new covered plate over sunken box for housing themodular switches , modular socket outlets,modularfan regulators etc.for one light/fan/exhaust fan/bell point controlledby one way switch,complete all as specified and as directedby Engineer-in-Charge. Note :-a) All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid forseparately . |
| 3 | Description all as per serial item No.02 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on independent board, complete all as specified and as directedby Engineer-in-Charge. |
| 4 | Description all as per serial item No.02 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board,complete all as specified and as directedby Engineer-in-Charge. |
| 5 | Description all as per serial item No.02 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathedcable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copperwire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge.Note : (i) Point wiring shall be done in a manner that not more than 02 socket point executed in one circuit.(ii) Each socket point will be measured and paid as per point. |
| 6 | Description all as per srl item No 02 here-in-before but for one socket outlet 16 Amp with 4.00 sq mm PVC insulated, unsheathedcable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copperwire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge.Note : (i) Point wiring shall be done in a manner that not more than 01 socket point executed in one circuit.(ii) Each socket point will be measured and paid as per point. |
| 7 | Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts, complete all as specified and as directedby Engineer-in-Charge. |
| 8 | Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts, complete all as specified and as directedby Engineer-in-Charge. |
| 9 | Supply and fixing of modular socket outletmultipin combined,6 Amp, one way, two module, 230 volts, complete all as specified and as directedby Engineer-in-Charge. |
| 10 | Supply and fixing ofmodular socket outletmultipin combined, (6pin), 6/16 Amp, one way, two module, 230 volts, complete all as specified and as directedby Engineer-in-Charge. |
| 11 | Supplyand fixing of modular bell push 6 Amp, 1 way, 1 module, 230 volts, complete all as specified and as directed by the Engineer-in-Charge. |
| 12 | Supply and fixing in repair calling bell, ding dong, 230 volt, complete all as specified and as directed by the Engineer-in-Charge. |
| 13 | Supply and fixing ceiling rose surface type 2/3 terminalpolycarbonate, isolated body, complete all as specified and as directed by the Engineer-in-Charge. |
| 14 | Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directedby Engineer-in-Charge. |
| 15 | Supplyand fixingas in repairelectronic Fan regulator, modular 100 watts, 1 module, 230 volts, 50 Hz, AC supply suitable for ceiling fan any type/make/sweep, complete, all as specified and as directed by the Engineer-in-Charge. |
| 16 | Supply and fixing in repairLED batten fitting 20 watt, 4 feet, polycarbonate housing with electronic drivercool/warm type, connecting with copper conductor flexible cablefrom ceiling rose to connector of the light, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LBLN-20-C-SQ of make Orient or equivalent make given in Appx \"B\". |
| 17 | Supply and fixing LED 22 watt integrated batten fitting with inbuilt lithium ion battery with minimum 4 hour back upincluding removing of unservicable light fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat part No.LED INVERTER BATTENHLB-08-22-CW-INV of make Halonix or equivalent in make given in Appx \"B\". |
| 18 | Supply and fixing in repairLED batten fitting 10 watt, 2 feet, polycarbonate housing with electronic drivercool/warm type, connecting with copper conductor flexible cablefrom ceiling rose to connector of the light, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LBLN-10-C-SQ of make Orient or equivalent make given in Appx \"B\". |
| 19 | Supply and fixing in replacement LED lamp 12 wattthreaded/pin end, warm/cool lamp type as per site requirement suitable for fixing on existing batten/angular holders, completeall as specified and as directed by the Engineer-in-Charge.Cat part No. BL0212WB22 of Make Benlo or equivalent make given in Appx \"B\". |
| 20 | Supplyand fixingin replacement LED lamp 9 wattthreaded/pin end, warm/cool lamp type as per site requirement suitable for fixing on existing batten/angular holders, completeall as specified and as directed by the Engineer-in-Charge. Cat part No. BL029WB22 of Make Benlo or equivalent make given in Appx \"B\". |
| 21 | Supplyand fixingLED lamp Invertor technology 9 watt with 4 hour power back up with efficiency more than 100 lumen per watt,Lithium ion battery, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.LED INVERTER LIGHT 10 W B22 CW IP of make Halonix or equivalent in make given in Appx \"B\". |
| 22 | Supply and fixing in repair, LED surface mounted bulk head luminaries 8-10 watt with min 800 lumen, IP 65, aluminium housing, surge protection including driver and LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LIBH-10-C-P of make Orient or equivalent make given in Appx \"B\". |
| 23 | Supply and fixing in repair,LED Bldg Security Light Fittings of capacity 40-45 watt made up of die castaluminiumhousing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.LSFS-45-CF-PC of make Orient orHLSLD-14-40-CWDL-R01 of make Halonix or equivalent make given in Appx \"B\". |
| 24 | Supply and fixinginverter LED security light luminaire 30 watt , pressure die cast aluminum housing, toughened heat resistant glass, IP66 protection, better optics for uniform distribution with multiplte LEDshaving optical grade polycarbonate lens with 3 to 4 hours battery back up, auto on offall accessories internally pre wired and including connecting up with Two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down oldunserviceable security light fitting of any description and in any position, complete all as specified and directed. Cat part NoLED SL 30W HLSLD-ML04-30-CWL-INV-RTC-R of make Halonix or equivalentin make given in Appx \"B\". |
| 25 | Material and labour for taking down existing light fitting of any type alongwith GI pipe/ pole of any dia / any size and supply and fixing of MS pipe (Hot dipped Galvanized) decorative pole in two sections i.e Top pipe not less than 70 mm outside dia x 1500 mm long and Bottom pipe not less than 110mm outside dia x 500 mm long, thickness of pipe not less than 3 mm with base plate 250 x 250 x 12mm thick having 14mm dia hole for fixing of foundation \"J\" bolts of size 12mm dia x 450 mm \"J\" including 115 x 200 mm long utility window in pole, including material & labour for fixing of suitable size nuts/bolts and washers including Tripple layer metallic PU paint (Etching, Epoxy & PU) having Embalishment aluminium castiing suitable for and alongwith 30/35 Watt Warm white LED post top lantern IP 65 environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs clear cover offers bright illumination including all fixing accessoreis including necessary excavation, removal and PCC 1:3:6 work as directed etc, complete all as specified and directed by Engineer-in-Charge. Cat Part No. HLPTP-95-2M-114/76-ACE-HDG of make Halonix or equivalent make given in Appx \"B\"Note :(i) Quoted rates shall be inclusive of excavation, taking down existing pole, all fixing acessories & PCC 1:3:6 for fixing of pole & post top lantern.(ii) Drawing of pole must get approved before installation..(iii) MS pipe of pole (Top & Bottom) should be ISI marked as per latest standard. |
| 26 | Supply and fixing in repair,9/12 watt thermoplastic wall mountingfixture (sketch type) with B-22 LED lamp and includingconnecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete and removing unserviceable light fittings, complete all as specified and as directed by the Engineer-in-Charge. Cat part No.DECO WALL LIGHT FROSTED of make Orient or LHFOGBE1TZ1W035of make Havells or equivalent make given in Appx \"B\". |
| 27 | Supply & fixingLED Flood lights, 100 watt, IP-66, aluminum die cast housing with unique lens system and toughened glasswith gasket240 volt, 50Hz, AC supplycompletewithall accessories internally pre wiredincluding connecting with flexible copper conductorto connector of the light with necessary fixing arrangements, including disconnecting and taking down existing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LFSM-100-C-V3 of make Orient or equivalentin make given in Appx \"B\". |
| 28 | Supply and fixingLED Bollard 8-10 watt, IP-65 , 6500 K luminaire made ofpressure die castaluminium housing and clear glass , 240 volt, 50HZ, AC supply , completewithall accessories including electronic driver,internally pre wiredincluding connecting withthree core flexible copper conductor cable from Electric Supply Source to connector of the light as in repair, complete all as specified and as directed by the Engineer-in-ChargeCat No. HLOB-02-10-CW of make .Halonix or equivalentin make given in Appx \"B\". |
| 29 | Supply and fixingLED post top luminaire 20W- 25W, 5700K, IP-65 made of pressure die-cast aluminium housing & clear glass 240 volt, 50HZ, AC supply completewithall accessories, including electronic driver, internally pre wiredincluding provision of 3 core PVC flexible copper conductor from electric supply source to connector of the light, including disconnecting and taking down existing light fitting and removing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat Part No.HLPT-S04-20-CW of Make Halonix or equivalentin make given in Appx \"B\". |
| 30 | Supply and fixing in repair, service bracket of mild steel pipe 25 mm bore medium grade of length 0.70 mtr fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts and washer and suitable reducer for connecting fitting to GI pipe as required at site includingtwo coats ofsynthetic enamel paintoverone coat of red oxide primer on mild steel work, complete all as specified and as directed by the Engineer-in-Charge. |
| 31 | Supply and fixing MCB SP, 6-32 Amps, 240 volt,10 KA ,\"B\" curve as per site requirement including removing old unserviceable MCB , complete all as specified and as directed by the Engineer-in-Charge. Cat Part No 811008 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 32 | Supply and fixing MCB SPN 32 Amps, 240 volt,10 KA ,\"B\" curve as per site requirement including removing old unserviceable MCB , complete all as specified and as directed by the Engineer-in-Charge. Cat Part No 811034 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 33 | Supply and fixing in repairMCB three pole and neutral 415 Volts, 63-100 Amps, 16 KA, 50 Hz thermal adjustable type , complete all as specified and directed by the Eng-in-charge. Cat Part No 811220 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 34 | Supply and fixing sheet metal enclosureVertical triple pole & neutral(VTPN) IP-43 including MCCB 100-125 Amp, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and includinglugs/thimbles duly crimped for connectionincluding making smooth the disturbed surface including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811888 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 35 | Supply and fixing sheet metal enclosuretriple pole & neutral(TPN) 4 way IP-43 with MCB TPN 63 Amp, 16 KA, 415 volts, flush /surface mounting double door duly grouted in solid block wall or on wooden board in and includinglugs/thimbles duly crimped for connectionincluding making smooth the disturbed surface including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811840 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 36 | Supply and fixing sheet metal MCB DB SPN8 way with 200 Amps rated bus bar single pole and neutral with double door IP-43 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811807 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 37 | Supply and fixing sheet metal MCB DB SPN 12 way with 200 Amps rated bus bar single pole and neutral withdouble door IP-43 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811808 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 38 | Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA \"B\" curve including removing old unserviceable enclosure, complete all as specified and as directed by the Engineer-in-Charge.Cat part No. 811955 of make Indo Asian or equivalent in make given in Appx \"B\". |
| 39 | Supply and laying as in repair sub main wiring with two run of 2.5 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 2.5 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 40 | Supply and laying as in repair sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 41 | Supply and laying as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and includingPVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 42 | Supply and laying as in repair sub main wiring with four run of 10 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 10 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and includingPVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i)Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii)Five runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 43 | Material & labourfor earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earthwire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test pointas directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/cboth ways with one handle for liftingmade out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testingas in repair, complete all as directed by Engineer-in-Charge and earth testing on completion . |
| 44 | Supply and fixing in repair, electronic meters temperproof LCD display with polycarbonate cover 230 V, 10-60 Amps, accuracy class-I 50 Hz, conforming to IS 13779, IP-54 with parameters to show data, time, current reading, load, PF, voltage and kWH, complete all as specified and as directed by Engineer-in-charge. |
| 45 | Supply and fixing in repair, electronic meters temperproof LCD display with polycarbonate cover 415 V, 10-60 Amps, accuracy class-I 50 Hz, conforming to IS 13779, IP-54 with parameters to show data, time, current reading, load, PF, voltage and kWH, complete all as specified and as directed by Engineer-in-charge. |
| 46 | Material and labour for Rigid non- metallic PVC Conduit 20mm exclusive of boxes (junction terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing on pole including all accessories such as clamp, couplers, lock nuts, saddles, pipe hooks etc complete all specified and directed. |
| 47 | Supply and fixing in replacement flexible cable PVC insulated and sheathed,3 core, circular multi stranded copper conductor of 4 Sqmmincluding removing unserviceable cable, complete all as specified and as directed by the Engineer-in-charge. |
| 48 | Supply and fixing in replacement flexible cable PVC insulated and sheathed,3 core, circular multi stranded copper conductor of 2.5 Sqmmincluding removing unserviceable cable, complete all as specified and as directed by the Engineer-in-charge. |
| 49 | Supply and fixing sheet metal MCB DB SPN4 way with 200 Amps rated bus bar single pole and neutral with double door IP-43 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811807 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 50 | Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty 2 core, 6 sq mm nominal cross section cable with PVC insulated aluminium conductormultistranded served with an inner sheathing of PVC tape and overall PVC sheathed in service connection, including disconnecting and taking down old U/S existingcable, complete all as specified and as directed by the Engineer-in-Charge. |
| 51 | Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty 2 core, 10 sq mm nominal cross section cable with PVC insulated aluminium conductormultistranded served with an inner sheathing of PVC tape and overall PVC sheathed in service connection, including disconnecting and taking down old U/S existingcable, complete all as specified and as directed by the Engineer-in-Charge. |
| 52 | Supply, fixing and testing automatic pressure pump of 0.5 HP capacity to maintain the desired pressure at end level from running water supply including placing on suitable plinth with fastner, nuts, bolts and washer and connection in existing GI pipe as in repair, complete all as specified and directed by Engineer-in-charge. Model Name- MINI FORCE II of Crompton Greaves Consumer Electricals limited or equivalentin make given in Appx \"B\". |
| 53 | Taking down unserviceable geyser and deposit to MES store yard and supply and fixing water heater, storage type (Geyser) vertical type with inner container of capacity 25 Ltrs of Mild steel with glass lined coating, Outer body made up of ABS corrosion/rust proof and shock resistant, electrically operated, AC 230 Volts, BEE 5 star rated (as per latest star label period), ISI marked, including fastener nuts required of suitable size fixed in brick/concrete wall, including writing the MES number with synthetic enamel paint complete all as specified and directed. The geyser should be tough enough to withstand pressure upto 8 bars. The inner tank should have a minimum 10 years warranty submitted by the tenderer from OEM. Model No Fabia 25 L of Make Havells and Crest 25 L of Make Bajaj or equivalent make given in Appx \"B\".Note :- Warranty certificate to be produced by the contractor from OEM for the following components before processing the RAR/Final Bill.(a) for Product - 04 Years(b) for Heating element - 06 Years(c) for Inner tank - 10 years |
| 54 | Material and labour for opening the stator & rotor of the 1200mm sweep ceiling fan, cutting the existing worn winding and rewinding the fan withsuperior quality copper wire and filling the varnish as insulation between each winds & covering each loops of winding by sleeves and paper & reassembling of , complete fan by fixing serviceable old and new parts of fans i.e. rubber bush, condenser and shackle housing , gun metal bushes, ball bearings, twin twisted copper cable, down rod assembly & canopy ,split pins , complete all as per manufacturers design air delivery including greasing, oiling & testing of fans all as per manufacturers design & speed , complete all as directed & approved for 1200mm sweep.Notes for item NO (i) to (vii) :- (i). The quoted unit rate shall be deemed to be inclusive of taking out defective parts and fixing of new parts. All new parts shall be measured and paid wide relevant items of the schedule. (ii). The rates for refixing and taking out serviceable parts shall be deemed to be included of quoted unit rates.(iii). New parts shall be of respective makes of fans.(iv). The quoted unit rates shall also include writing of MES No on fans(v). Unserviceable /defective retrieved parts shall be credited under sch of credit.(vi). After assembling all fans shall be tested for the speed as directed.(vii). All the fans shall be repaired/rewind at AGE E/M store yard only. |
| 55 | Description allas per serial item No 54 here-in-before but for Exhaust fans of 250/300mm sweep, complete all as specified and as directed by the Engineer-in-Charge. |
| 56 | Supply and fixing as in repair PCB unit suitable for BLDC ceiling fan of 1200mm sweep single phase, 240 volts of make crompton, Halonix, Havells etc., complete all as specified and as directed by the Engineer-in-Charge. |
| 57 | Supply and fixing as in repair, PVC White Freshner Exhaust Fan 250mm sweep, 1400 RPM, Aerodynamically designed blanced blades, Rust proof body, Low power consumption, 5 blades complete with Louvers easy to mount, complete all as specified and as directed by Engineer-in-charge. SKU Code 70049 of make Bajaj or equivalent in make given in Appx \"B\". |
| 58 | Supply and fixing as in repair, PVC White Freshner Exhaust Fan 300mm sweep, 1400 RPM, Aerodynamically designed blanced blades, Rust proof body, Low power consumption, 5 blades complete with Louvers easy to mount, complete all as specified and as directed by Engineer-in-charge. SKU Code 70062 of make Bajaj or equivalent in make given in Appx \"B\". |
| 59 | Supply and fixing of heavy duty exhaust fan 300mm sweep with corrosion resistant metal body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, PVC base framewith rubbermountings for silent operation, maximum watt input not more than 50 watt, 1400 RPM,minimum air delivery 750 cum/hr,metal bladestesting as in repair , complete all as specified and as directedby Engineer-in-Charge. SKU code - 70003of make Bajaj or equivalentin make given in Appx \"B\". |
| 60 | Supply and fixingas in repairheavy duty wall mounting fan400 mm sweep with corrosion resistant PVC body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotormounted on two ball bearings, aerodynamically contoured blades, rigid frame, PVC blades andtesting , complete all as specified and as directedby Engineer-in-Charge. SKU Code 250552 of make Bajaj or equivalentin make given in Appx \"B\". |
| 61 | Supply and fixing ball bearing No 6201 for 1200/1400mm sweep ceiling fans , complete all as specified and as directed by the Engineer-in-charge. |
| 62 | Supply and fixing ball bearingfor 250 to 450 mm sweep Exhaust fans, complete all as specified and as directed by the Engineer-in-charge. |
| 63 | Supply and fixing rubber clamp of suitable size for hanging of 1200-1400 mm ceiling fans in 40/50 mm GI pipe,as in repair , complete all as specified and as directed by the Engineer-in-charge. |
| 64 | Supply and fixing gun metal bush suitable for 1200/1400mm sweep ceiling fan, complete all as specified and as directed by the Engineer-in-charge. |
| 65 | Supply and fixing in repair fan capacitor 2.5 MFD suitable for 1200/1400 mm ceiling fan, complete all as specified and as directed by the Engineer-in-charge. |
| 66 | Supply and fixing in repair, Switch Paino flush type single pole 6 Amps, complete all as specified and directed by Engineer-in-charge. |
| 67 | Supply and fixing in repair, Switch Paino flush type single pole 16 Amps complete all as specified and directed by Engineer-in-charge. |
| 68 | Supply and fixing in repair, Socket outlet 2 in 1, 3 pin 6 Amps, complete all as specified and directed by Engineer-in-charge. |
| 69 | Supply and fixing in repair, Socket outlet 6/16Amps 6 Pin, complete all as specified and directed by Engineer-in-charge. |
| 70 | Supply and fixing in repair, stepped type electronic fan regulator flush type on the existing laminated sheet etc., complete all as specified and directed by Engineer-in-charge. |
| 71 | Supply and fixingas in repair modular PVC sheet/cover plate 3 way suitable for fixing switch/socket/fan regulators etc on existing MS boxes of any make as per site requirement including removing unserviceable items, complete all as specified and as directed by the Engineer-in-charge. Cat part No.800063 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 72 | Supplying and fixing in repair Thermoplastics IP 65 MCB distribution board 2 way in accordance with IEC 60670-24 which should be shock proof and double insulated. IP65 in accordance with IEC 60529 (EN 60529), weather proof, Corrosion free, Acid & Chemical Resistant, temperature resistance, Made of material Polycarbonate for Lid part andPS (polystyrene) for Base with transparent lid, sealable. halogen & Silicone free recyclable material, .The gasket material shall be Polyurethane, while the gasket shall be internally embedded.The enclosure is Consisting PE and N FIXCONNECT® terminal with provision for cable entry through top, bottom and sides. The impact strength of enclosure i.e. the Degree of Protection against Mechanical load shall be in accordance with IEC 62262 forIK 08 (5 Joule).And Enclosure should withstand Glow wire test at 750°C in accordance with IEC 60695-2-11 flame retardant, Self Extinguishing, UL subject 94,V-2. Color: Grey, RAL 7035.Suitable for indoor installation and outdoor installation, protected against weather influences , complete all as specified and directed by Engineer-in-Charge. Cat part No.KV7103of make Hensel or equivalentin make given in Appx \"B\". |
| 73 | Supply and fixing as in repair,MCCB, 4 pole, 100 Amp, 415 Volts, 16 KA , fixedtype including fixing arrangement, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.830022 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 74 | Supply and fixing as in repair,MCCB, 4 pole, 125 Amp, 415 Volts, 16 KA , fixedtype including fixing arrangement, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.830023 of make Indo Asian or equivalent in make given in Appx \"B\". |
| 75 | Supply and fixing in replacement flexible cable PVC insulated and sheathed,3 core, circular multi stranded copper conductor of 1.50 Sqmmincluding removing unserviceable cable, complete all as specified and as directed by the Engineer-in-charge. |
| 76 | Supply only flexible cable PVC flat insulated and sheathed,2 core, multi stranded copper conductor of 1.5 Sqmmincluding removing unserviceable cable, complete all as specified and as directed by the Engineer-in-charge. |
| 77 | Supply and fixing brass connection pipe 600 mm longhaving wire mesh coating over it with brass nuts and washers suitable for connecting geysers inlet and outlet with GI tubings including taking out old unserviceableconnections of any description all as specified and as directed by Engineer-in-charge. |
| 78 | Note:-Amount of credit ofRs.1,46,221.00for retrieved materials is mentioned in Schedule of Credit Page No…………………. of tender documents in pdf form which will be deducted offline while acceptance of tender. |
