|
| 1 | Dismantling doors,windows and clerestory windows (steel or wood) shutter including chowkhats,architrave,holdfasts etc. complete and stacking within 50 metres lead as per direction of Engineer-in-charge. : Of area 3 sq.metres and below. |
| 2 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead: For thickness of tiles 10 mm to 25 mm. |
| 3 | Demolishing cement concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineer-in-Charge Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 4 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead as per direction of Engineer-in-charge. |
| 5 | Demolishing brick work manually/ by mechanical means including stacking of serviceble material and disposal of unserviceble material within 50 metres lead as per direction of Engineer-in-charge. : In cement mortar. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work upto plinth level: 1:2:4 (1 Cement: 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size. |
| 7 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand) |
| 8 | Centring and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access plateform. |
| 9 | Removing dry or oil bound distemper by scarapping,sand papering and preparing the surface smooth including necessary repairs to scratches etc.complete. |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 11 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. |
| 12 | 6 mm cement plaster to ceiling of mix :1:3 (1 cement :3 fine sand) |
| 13 | 12 mm cement plaster of mix :1:4 (1 cement :4 coarse sand) |
| 14 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer in all colours and shade in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm |
| 15 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 16 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS :15622 of approved make in all colours such as White, Ivory, Grey, Fume Red Brown laid on 20 mm thick cement mortar 1:4 (1 cement :4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete. |
| 17 | Providing and fixing 18 mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen plateforms, vanity counter facias and similar locations of required size of approved shade colour and texture laid over 20 mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) with joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels: Granite of any colour and shade; Area of slab over 0.50 sqm. |
| 18 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 19 | Distempering with 1st quality acrylic distemper (ready mixed) havingVOCcontentlessthan50gms/litre,ofapproved manufacturer,ofrequiredshadeandcolourcomplete,asper manufacturer’s specification. Two or more coats on new work |
| 20 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge; Concealed work including cutting chases and making good the walls etc.; 20 mm nominal outer dia Pipes. |
| 21 | Providing and fixing G.I.pipes complete with G.I.fittings and clamps,including cutting and making good the walls etc.; Internal work -Exposed on wall; 15 mm dia.nominal bore |
| 22 | Providing and fixing G.I.pipes complete with G.I.fittings and clamps,including cutting and making good the walls etc.; Internal work -Exposed on wall; 20 mm dia nominal bore |
| 23 | Providing and fixing G.I.pipes complete with G.I.fittings and clamps,including cutting and making good the walls etc.; Internal work -Exposed on wall; 25 mm dia nominal bore |
| 24 | Providing and fixing G.I.Union in G.I.pipe including cutting and threading the pipe and making long screws etc.complete (new work): 15 mm nominal bore |
| 25 | Providing and fixing G.I.Union in G.I.pipe including cutting and threading the pipe and making long screws etc.complete (new work): 20 mm nominal bore |
| 26 | Providing and fixing G.I.Union in G.I.pipe including cutting and threading the pipe and making long screws etc.complete (new work): 25 mm nominal bore |
| 27 | Providing and placing on terrace (at all floor levels) Polythylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 28 | Providing and fixing ball valve (brass) of approved quality complete: High or low pressure with plastic floats; 15 mm nominal bore |
| 29 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour: 15 mm nominal size weighing not less than 32 gms. |
| 30 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour: 20 mm nominal size with dimensions 69 x 43 x 43 mm weighing not less than 45 gms |
| 31 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball: 20 mm nominal bore,120 mm long weighing not less than 198 gms. |
| 32 | Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100 mm sand cast Iron P or S trap,10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C.pan of size 580 x 440 mm with integral type foot rests |
| 33 | Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS :7231, with all fittings and fixture complete including cutting and making good the walls and floors wherever required : W.C.pan with ISI marked white solid plastic seat and lid |
| 34 | Providing and fixing wash basin with C.I. brackets,15 mm C.P. brass pillar taps, 32mm C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White vitreous China; Wash basin size 630 x 450 mm with a single 15 mm C.P.brass pillar taps |
| 35 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS :13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board; 610 x 460 mm bowl depth 200 mm |
| 36 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & makeas approved by Engineer in charge. (a) 15 mm nominal dia |
| 37 | Providing and fixing C.P.brass angle valve for basin mixer and gyser points of approved quality conforming to IS :8931:15 mm nominal bore |
| 38 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge |
| 39 | Providing and fixing P.V.C.waste pipe for sink or wash basin including P.V.C.waste fittings complete: Flexible pipe; 40 mm dia |
| 40 | Providing and fixing uplasticised PVC connection pipe with brass unions: 45 cm length; 15 mm nominal bore |
| 41 | Providing and fixing 100 mm sand cast Iron grating for gully trap |
| 42 | Providing and fixing C.P.brass long nose bib cock of approved quality conforming to IS standard and weighing not less than 810 gms: 15 mm nominal bore |
| 43 | Providing and fixing C.P.brass stop cock (concealed) of standard design and of approved make conforming to IS :8931: 15 mm nominal bore |
| 44 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 45 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 46 | Applying priming coat :With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 47 | Painting with synthetic enamle paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 48 | Providing and fixing anodised aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sectios/ appropriate Z secions and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips,or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required EPDM rubber/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/penelling, C.P.brass/stainless steel screws, all complete as per architectual drawings and the directions of Engineer-in-charge.(Glazing and panelling to be paid for separately):For fixed portion; Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 49 | Providing and fixing anodised aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sectios/ appropriate Z secions and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips,or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required EPDM rubber/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever requiredincluding cleat angle, Aluminium snap beading for glazing/penelling, C.P.brass/stainless steel screws, all complete as per architectual drawings and the directions of Engineer-in-charge.(Glazing and panelling to be paid for separately):For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately); Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 50 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade) particle board Grade I,Type II conforming to IS :12823 in panelling fixed in alluminium doors,windows shutters and partition frames with C.P.brass/stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge:Pre-laminated particle board with decorative lamination on one side and balancing laminatioin on other side. |
| 51 | Providing and fixing glazing in aluminium door,windows,ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc.complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness. |
| 52 | Providing and fixing IS :3563 marked Aluminium die cast body tubular type universal hydraulic door closer necessary accessories and screws etc.complete. |
| 53 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS :6315 marked, for doors including cost of cutting floors as required,embedding in floors and cover plates with brass pivot and single piece M.S.sheet outer box with slide plate etc.complete as per the direction of Engineer-in-charge:With stainless steel cover plate |
| 54 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with necessary screws etc.complete : 100 mm |
| 55 | Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc. complete as per dirction of Engineer-in-charge; Powder coatd minimum thickness 50 micron aluminium tubular handle bar. |
| 56 | Providing and fixing ISI marked aluminium sliding door boltsISI marked anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with nuts andscrews etc. complete : 300x 16 mm |
| 57 | Providing and fixing ISI marked aluminium sliding door boltsISI marked anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with nuts andscrews etc. complete : 250x 16 mm |
| 58 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 per IS :1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 300 x 10 mm |
| 59 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 per IS :1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 250 x 10 mm |
| 60 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 per IS :1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 200 x 10 mm |
| 61 | Repair to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.metres and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement :4 coarse sand) |
| 62 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required . In gratings, frames, guard bar, ladders, railings, brackets, gates and similar works. |
| 63 | Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of \"L\" shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge |
| 64 | Mirror polishing on marble work /Granite/ stone work wherever required to give high gloss finish complete. |
| 65 | Cutting holes upto 30 x 30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular) bricks. |
| 66 | Cutting holes upto 15 x 15 cm in R.C.C.floors and roofs for passing drain pipe etc.and repairing the hole after insertion of drain pipe etc.with cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof. |
| 67 | Providing and fixing on wall face unplasticised -Rigid PVC rain water pipes conforming to IS :13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion: (i) Single socketed pipes; 110 mm diameter |
| 68 | Providing and fixing on wall face unplasticised -PVC moulded fittings/accessories for unplasticised -Rigid PVC rain water pipes conforming to IS :13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion:Coupler;110 mm |
| 69 | Providing and fixing on wall face unplasticised -PVC moulded fittings/accessories for unplasticised -Rigid PVC rain water pipes conforming to IS :13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion: Single tee without door;110x110x110 mm |
| 70 | Providing and fixing on wall face unplasticised -PVC moulded fittings/accessories for unplasticised -Rigid PVC rain water pipes conforming to IS :13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion:Bend 87.5o;110 mm bend |
| 71 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard woodplugs,screwed with M.S.screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement :4 coarse sand) and making good the wall etc. complete:110 mm |
| 72 | Providing and fixing on wall face unplasticised -PVC moulded fittings/accessories for unplasticised -Rigid PVC rain water pipes conforming to IS :13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion: Single tee with door;110x110x110 mm |
| 73 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm |
| 74 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with gery cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with Base of cement mortar 1:4 (1 cement :4 coarse sand) :25 mm thick |
| 75 | Kota stone slabs 20 mm thick in risers of steps,skirting,dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs,including rubbing and polishing complete. |
| 76 | Stone tile (Polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and cement slurry @ 3.3 Kg. / Sqm. including pointing in white cement complete. 8 mm thick; Granite of any colour and shade |
| 77 | Carriage of material by mechanical transport including loading, unloading and stacking complete; Lime, moorum, building rubbish, earth, manure or sludge and excaveted rock :Lime, moorum, building rubbish ;17 km lead |
