Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | REPAIRS TO HANGAR DOORS |
| 2 | M&L for carefully taking down and refixing existing sliding hangar door shutters, each leaf of size exceeding 2.50 m in width (but not exceeding 7.50 m) and height from 7.50 m to 12.0 m (clear opening), including:(i) Straightening of bent/misaligned top and bottom rails(ii) Replacement of unserviceable rollers(iii) Tightening or replacement of loose nuts and bolts(iv) Necessary welding, drilling, and replacement of broken locking arrangements(v) Oiling, greasing, and adjustment for smooth functioning(vi) Positioning of the door shutter in the same opening(vii) Resetting of derailed steel gates on existing railsNOTES:(1) Replacement of broken or worn-out parts such as nuts, bolts, rods, flat iron, angle iron, channels, guide rails, ball bearings, or major structural components shall be measured and paid separately.(2) All tools, plants, machinery, scaffolding, ladders, lifting equipment, and labour required for execution shall be deemed included in the quoted rate. |
| 3 | M&L for cleaning, greasing, oiling, and adjustment of top hangar door rail track, including:(i) Removal of deposits, dirt, or rust from the track(ii) Inspection and rectification of top guide channels, connecting members, and pulleys(iii) Tightening of loose nuts, bolts, and screws(iv) Minor welding if required(v) Ensuring proper alignment and smooth functioning of the hangar doorNOTES:(1) Unit covers the full top rail track of one hangar door opening, including all sliding shutters, with cleaning, greasing, adjustment, and minor welding as required for smooth operation.(2) Minor consumables and routine adjustments are included in the quoted rate.(3) Major replacements (rollers, ball bearings, shafts) shall be measured and paid separately.(4) All tools, plants, machinery, scaffolding, ladders, and labour required shall be deemed included in the quoted rate. |
| 4 | M&L for cleaning, greasing, oiling, and adjustment of bottom hangar door rail track, including:(i) Complete cleaning of the rail track to remove deposits, dirt, rust, or other obstructions (mechanical or chemical methods if required)(ii) Inspection and rectification of bottom guide channels, connecting members, and door rollers(iii) Tightening of loose nuts, bolts, and screws(iv) Minor welding if required(v) Ensuring proper alignment and smooth functioning of the hangar doorNOTES:(1) Unit covers the full bottom rail track of one hangar door opening, including all sliding shutters, with cleaning, greasing, adjustment, and minor welding as required for smooth operation.(2) Minor consumables and routine adjustments are included in the quoted rate.(3) Major replacements (rollers, ball bearings, shafts) shall be measured and paid separately.(4) All tools, plants, machinery, scaffolding, ladders, and labour required shall be deemed included in the quoted rate. |
| 5 | M&L for oiling, greasing, and cleaning of pulleys for each steel sliding hangar door, including:(i) Cleaning using approved industrial cleaning agents/thinner, if required(ii) Oiling and greasing to reduce friction(iii) Adjustment for smooth functioning of doorNOTES:(1) Minor consumables and routine adjustments included.(2) T&P, scaffolding, ladders, and labour included. |
| 6 | M&L for easing, adjusting, greasing, and alignment of hangar door base rollers, top guide rollers, wheel shafts, including:(i) Taking down existing parts if required by gas welding(ii) Necessary arrangements for lifting door (jack/lifting tools)(iii) Removal, overhauling, and refixing of wheels(iv) Ensuring smooth functioning and alignment of doorNOTES:(1) Minor consumables included.(2) Major components (rollers, shafts) measured separately.(3) T&P, scaffolding, ladders, and labour included. |
| 7 | S&F in repair or replacement of hangar door wheel made of mild steel (IS 2062 Fe-410) with diameter not exceeding 350 mm and thickness not more than 100 mm, including:(i) Cutting of grooves for bearing and circlip(ii) Fitting high-precision wheel with locking pin(iii) Fixing of shaft for bottom support after lifting existing door(iv) Greasing and welding work as requiredNOTES:-(1) Wheel must match or exceed the specification of the original wheel (diameter & shaft diameter same or higher).(2) Rate includes T&P, scaffolding, labour; shaft/axle included.(3) Ball bearings measured separately. |
| 8 | S&F in repair or replacement of top guide roller assembly (MS) with diameter not exceeding 300 mm and thickness 30–100 mm, including:(i) Fixing of ball bearing and central pin(ii) Lifting existing door for installation(iii) Welding, greasing, and alignment of top guide for smooth shutter movementNOTES:(1) Roller must match or exceed specification of original.(2) Rate includes T&P, scaffolding, labour; shaft/axle included.(3) Ball bearings measured separately. |
| 9 | S&F in replacement of stainless steel ball bearing of any diameter for hangar door rollers, as per existing design/specification.NOTES:(1) Specifications must match or exceed original.(2) T&P, scaffolding, ladders, and labour included. |
| 10 | M&L for routine preventive maintenance of sliding hangar door shutters complete all as specified and directed including:(i) Inspection of top and bottom rail tracks, pulleys, rollers, guide channels, and connecting members.(ii) Cleaning of rails and tracks by mechanical or chemical methods, if required.(iii) Lubrication, greasing, and oiling of rollers, bearings, pulleys, and locking arrangements.(iv) Adjustment and tightening of loose nuts, bolts, screws, and minor fittings.(v) Minor welding or rectification works necessary to ensure smooth operation.(vi) Checking and ensuring proper alignment of top/bottom guide channels, rollers, and door leaves.NOTES:(1) Payment shall be made per visit actually executed, after completion of primary repair works under Items 1–8.(2) The quoted rate shall be deemed to include all tools, plants, machinery, scaffolding, ladders, safety arrangements, and labour required for execution.(3) Minor consumables and fasteners such as nuts, bolts, washers, lubricants, etc. shall be deemed included in the quoted rate.(4) Replacement of major components such as rollers, wheels, shafts, bearings, etc. shall be measured and paid separately under Items 6–8.(5) Visits shall be carried out when called upon by the user or Engineer-in-Charge for preventive maintenance or rectification.(6) Preventive maintenance under this item shall be applicable only after completion of repair works (Items 1–8, as applicable) and successful testing and handing over of the respective door. Maintenance for each door shall commence from the date of certification of functional completion by the Engineer-in-Charge. |
| 11 | GENERAL NOTES COMMONLY APPLICABLE TO ITEM NO 1.01 TO 1.08(1) Scope LimitationThese items cover mechanical repair, overhauling, replacement, alignment, and refixing of sliding hangar door shutters and associated mechanical components only. Electrical/motorized systems, if any, are excluded.(2) Experienced ManpowerAll works shall be executed only through skilled and experienced workmen having proven experience in handling and repairing large sliding steel hangar doors or similar heavy industrial doors.contd.... |
| 12 | GENERAL NOTES COMMONLY APPLICABLE TO ITEM NO 1.01 TO 1.08 (CONTD....)(3) Careful Execution & ProtectionAll dismantling, handling, repair, welding, alignment, and re-erection works shall be carried out carefully and systematically so as not to cause any damage to existing doors, rails, structures, finishes, or embedded parts.(4) Safety RequirementsThe contractor shall strictly follow all safety precautions, including use of PPE, proper scaffolding, barricading, warning signage, and safe lifting/jacking arrangements.(5) Tools, Plants & MachineryAll T&P, scaffolding, lifting arrangements, jacks, welding equipment, and machinery required shall be arranged by the contractor and deemed to be included in the quoted rates.(6) Rectification of DamageAny damage caused to hangar doors, rails, structures, or surrounding installations due to the contractor’s operations shall be made good or replaced at the contractor’s own cost.(7) Inspection, Trial & AcceptanceAfter completion of repair of each door, the same shall be cleaned, lubricated, adjusted, and operated repeatedly to demonstrate smooth and safe functioning before acceptance.(8) Quality & Workmanship ResponsibilityThe contractor shall remain fully responsible for the quality of workmanship and proper functioning of doors repaired under Items 1–8 during the execution period. |
| 13 | SPECIAL RESPONSE & PENALTY NOTE (APPLICABLE TO ITEM NO 1.09)(1) Attendance & InspectionThe contractor shall attend the site within 24 hours of intimation, inspect the complaint, assess the defect, and take necessary immediate action to ensure safety and functionality.(2) Rectification PeriodWhere replacement of parts or major rectification is involved, the contractor shall complete the work within the time period approved by the Engineer-in-Charge.(3) Penalty ClauseIn case the contractor fails to attend the site within 24 hours of intimation, recovery at the rate of ₹500 per day per door shall be effected till the date of attendance, without prejudice to the department’s right to get the work executed through other agencies at the risk and cost of the contractor. |
| 14 | REPAIRS TO ROLLING SHUTTERS |
| 15 | S&F in repairs (replacement) steel rolling shutter, manual / push-pull operated type, without ball bearings, area not exceeding 12.0 sqm, fabricated with 1.00 mm thick interlocking steel laths, complete with steel suspension shaft, spring assembly, MS guide channels, hood/top cover, bottom lock plate/rail, anchoring rods, hasp and staple, fixed in position as indicated, conforming to IS 6248 and relevant General Specifications, complete all as specified and as directed by the Engineer-in-Charge.NOTES:(1) Painting on the rolling shutter shall be measured and paid for separately under the relevant painting item.(2) All components of the rolling shutter such as laths, suspension shaft, springs, guide channels, hood/top cover, locking arrangement, and other accessories shall conform to SSR Part-I, 1991, Para 10.23 and subsequent relevant paragraphs, IS 6248, and applicable General Specifications. The sizes, thicknesses, and constructional details not expressly stated in this item description shall be deemed to be as per the said SSR provisions.(3) Quoted rate shall be deemed to include dismantling of existing unserviceable shutter, supply, fixing, alignment, adjustment, testing, and all materials, labour, tools, scaffolding, and incidental works required for satisfactory replacement. |
| 16 | S&F in repairs (replacement) steel rolling shutter, gear-operated type, with ball bearings, area not exceeding 35.0 sqm, fabricated with 1.25 mm thick interlocking steel laths, complete with steel suspension shaft, spring assembly, MS guide channels, hood/top cover, bottom lock plate/rail, anchoring rods, hasp and staple, bevel gear / chain mechanism, fixed in position as indicated, conforming to IS 6248 and relevant General Specifications, complete all as specified and as directed by the Engineer-in-Charge.NOTES: (1) Painting on the rolling shutter shall be measured and paid for separately under the relevant painting item.(2) All components of the rolling shutter such as laths, suspension shaft, springs, guide channels, hood/top cover, locking arrangement, and other accessories shall conform to SSR Part-I, 1991, Para 10.23 and subsequent relevant paragraphs, IS 6248, and applicable General Specifications. The sizes, thicknesses, and constructional details not expressly stated in this item description shall be deemed to be as per the said SSR provisions.(3) Quoted rate shall be deemed to include dismantling of existing unserviceable shutter, supply, fixing, alignment, adjustment, testing, and all materials, labour, tools, scaffolding, and incidental works required for satisfactory replacement. |
| 17 | M&L for routine repair and maintenance of existing rolling shutters without taking down, including:(i) Inspection of shutter, guide channels, rollers, spring assembly, hood/top cover, and all moving parts.(ii) Cleaning of shutter, rails, guide channels, rollers, and moving parts.(iii) Lubrication, greasing, and oiling of rollers, shafts, bearings, springs, and locking arrangements.(iv) Adjustment or tightening of loose nuts, bolts, screws, and minor fittings.(v) Minor welding, straightening, or rectification to ensure smooth, noiseless, and jerk-free operation.(vi) Alignment of shutter leaves, guide channels, and bottom lock plate for proper functioning.NOTES: (1) The rate includes all labour, tools, plants, scaffolding, ladders, lifting arrangements, minor consumables, and safety equipment required for execution.(2) Replacement of major components such as laths, springs, rollers, shafts, or gear assemblies shall be measured and paid separately under relevant “Supply Only” items.(3) Any damage caused to the shutter or surrounding structure during execution shall be rectified by the contractor at his own cost.(4) Doors shall be handed over in smooth, safe, and fully functional condition to the satisfaction of Deptt. |
| 18 | M&L for taking down, repairing, overhauling, and refixing self-coiling / push-pull type steel rolling shutters (area exceeding 9.0 sqm but not exceeding 12.0 sqm), including:(i) Careful dismantling with proper support of shutter, frames, and brackets.(ii) Straightening of top and bottom rails, frames, guide channels, and brackets.(iii) Overhauling rollers, shafts, pulleys, and locking arrangements for smooth functioning.(iv) Minor welding, drilling, or rectification as required.(v) Refitting the shutter with proper alignment; lubrication, greasing, and oiling of all moving parts.(vi) Adjustment or tightening of loose nuts, bolts, screws, or minor fittings.(vii) Testing and commissioning to ensure smooth, noiseless, jerk-free, and safe operation.NOTES: (1) All tools, plants, scaffolding, ladders, lifting arrangements, and labour required for dismantling, holding, and refixing are deemed included in the quoted rate.(2) Replacement of major components (laths, springs, shafts, rollers, gear assemblies) shall be measured and paid separately under relevant “Supply-Only” items.(3) Minor consumables (nuts, bolts, washers, clips) are included in the rate.(4) Contractor shall avoid any damage to shutter, rails, frames, brackets, or surrounding structure; any damage caused shall be rectified at contractor’s own cost.(5) Doors shall be handed over fully functional, smooth, and safe to the satisfaction of the Engineer-in-Charge. |
| 19 | M&L for taking down, repairing, overhauling, and refixing gear-operated steel rolling shutters (area exceeding 12.0 sqm but not exceeding 35.0 sqm), including:(i) Careful dismantling with proper support of shutter, frames, and brackets.(ii) Straightening of top and bottom rails, frames, guide channels, and brackets.(iii) Overhauling rollers, shafts, pulleys, gear assemblies, and locking arrangements for smooth functioning.(iv) Minor welding, drilling, or rectification as required.(v) Refitting the shutter with proper alignment; lubrication, greasing, and oiling of all moving parts.(vi) Adjustment or tightening of loose nuts, bolts, screws, or minor fittings.(vii) Testing and commissioning to ensure smooth, noiseless, jerk-free, and safe operation.NOTES:(1) All tools, plants, scaffolding, ladders, lifting arrangements, and labour required for dismantling, holding, and refixing are deemed included in the quoted rate.(2) Replacement of major components (laths, springs, shafts, rollers, gear assemblies) shall be measured and paid separately under relevant “Supply-Only” items.(3) Minor consumables (nuts, bolts, washers, clips) are included in the rate.(4) Contractor shall avoid any damage to shutter, rails, frames, brackets, or surrounding structure; any damage caused shall be rectified at contractor’s own cost.(5) Doors shall be handed over fully functional, smooth, noiseless, jerk-free, and safe to the satisfaction of the Engineer-in-Charge. |
| 20 | Supply only 1.0 mm thick interlocking steel lath strips for manual / push-pull rolling shutters up to 12.0 sqm, including mild steel clips at both ends, complete all as specified and directed. |
| 21 | Supply only 1.25 mm thick interlocking steel lath strips for gear-operated rolling shutters up to 35.0 sqm, including mild steel clips at both ends, complete all as specified and directed. |
| 22 | Supply only mild steel spring, 75 mm to 150 mm dia, made of high tensile steel wire conforming to IS: 4454, having 60 to 80 helical turns for smooth working condition of rolling shutters, complete all as specified and directed. |
| 23 | Supply only mild steel anchoring rod, 50 mm dia, for rolling shutters, complete all as specified and directed. |
| 24 | Supply only bevel or chain gear assembly suitable for gear-operated rolling shutters, including crank handle, chain, bearings, and fixings, complete all as specified and directed. |
| 25 | Supply only mild steel rollers with suitable diameter, section, bearings, and locking pins for rolling shutters, complete all as specified and directed. |
| 26 | Supply only fabricated mild steel sheet hood/top cover for rolling shutters, 1.0 mm thick, cut and shaped to size with proper stiffening using angle/flat stiffeners at top and bottom edges, edges beaded or formed as required, suitable for fixing to bracket plates, complete as specified and directed by the Engineer-in-Charge. |
| 27 | Supply only fabricated mild steel lock plate (bottom lock plate / bottom rail) for steel rolling shutters, fabricated to suit the width of the existing shutter opening, of riveted construction, made out of mild steel sheet not less than 3.15 mm thick, reinforced at bottom with mild steel angle section not less than 35 × 35 × 5 mm, designed to be interlocked with the bottom-most lath of the curtain, complete with sliding bolts with arrangement for pad locking and mild steel pulling handles (one handle for widths up to 2.5 m and two handles for widths above 2.5 m, fixed on both interior and exterior faces), strictly conforming to SSR Part-I, 1991, Para 10.23.3, IS 6248 and relevant General Specifications, complete all as specified and directed. |
| 28 | M&L preparing new or previously untreated Steel and Iron Surfaces of rolling shutters or any individual parts, of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and directed. |
| 29 | M&L preparing old Treated/Painted Steel and Iron Surfaces of rolling shutters, of any description, over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and directed. |
| 30 | REPAIRS TO MILD STEEL WORKS, TRUSS AND ROOFINGS |
| 31 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings and removal from sitecomplete all as specified and as directed. |
| 32 | Dismantling wrought iron or mild steel work of any description and removing the same from site, complete all as specified and as directed. |
| 33 | Dismantling structural steel work including doors, gates but excluding framed truss etc.and removal from site complete all as specified and directed. |
| 34 | M&L for rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates, including cutting, hoisting, fixing in position, drilling holes, welding, or bolting, Grade Fe-410-W (Gde-E 250) quality-A, complete all as specified and directed |
| 35 | M&L for structural steel work Fe-410-W (Gde E-250) Quality-A in roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., complete all as specified and as directed by the Engineer-in-Charge |
| 36 | M&L for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 or RHS/SHS Sections conforming to IS 4923:1997 grade YST 210 complete all as specified and directed. |
| 37 | M&L for Rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment Gde Fe 410W complete all as specified and directed. |
| 38 | M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end & screwed the other or screwed both ends each screwed end to be fitted with washers & one hexagonal or square nut, exc 22.5cm but n exc 30 cm long, diameter 16 to 20 mm complete all as specified and directed. |
| 39 | M&L for Rolled mild steel framed work, Fe-410W(Gde-E-250) quality-B as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering), running rails and guides) and hanging; also fastening and fixing completeall as specified and directed. |
| 40 | M&L for Mild steel plain black sheet, 1.00 mm thick, as in wall cladding, steel gates and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fised to steel framing with 40mm lap joints with riveted or welded seams including bending or turning up, mitred angles, etc as required complete all as specified and directed. |
| 41 | S&F pre-painted olive green colour galvalume aluminium-zinc coating, GI-based corrugated steel sheets, 0.50 mm thick, having minimum tensile strength 550 MPa, as in hangar roof covering / wall cladding, fixed with self-tapping screws or L/J-type hooks, including necessary laps, cuttings and waste, provided at any height up to 25 m, complete all as specified and as directed by the Engineer-in-Charge |
| 42 | S&F pre-painted olive green colour galvalume aluminium-zinc coating, GI-based plain steel sheets, 0.50 mm thick, having minimum tensile strength 550 MPa, as in roof covering / wall cladding / steel gates / ridge portion, including necessary bending, moulding and forming to required shapes, fixed with self-tapping screws, provided at any height up to 25 m, complete all as specified and as directed by the Engineer-in-Charge |
| 43 | M&L preparing new or previously untreated steel and iron surfaces of parking sheds, gates, grills, small roof members and similar works, of any description, over 10 cm width or girth, and applying two coats of first quality synthetic enamel paint over a red oxide zinc chrome primer, including cleaning, surface preparation, tools, plants and all incidental works, complete all as specified and as directed by the Engineer-in-Charge |
| 44 | M&L for preparation of existing treated or painted steel and iron surfaces, of any description, over 10 cm width or girth, including surface cleaning and application of one coat of first-quality synthetic enamel paint, at a height up to 12 m, complete all as specified and directed by the Engineer-in-Charge. |
| 45 | M&L for preparation of existing treated or painted steel and iron surfaces, of any description, over 10 cm width or girth, including surface cleaning and application of one coat of first-quality synthetic enamel paint, at a height above 12 m and up to 25 m, complete all as specified and directed by the Engineer-in-Charge. |
| 46 | M&L preparing new or previously untreated steel and iron surfaces of roof trusses and associated structural members, of any description, over 10 cm width or girth, and applying two coats of first quality synthetic enamel paint over a red oxide zinc chrome primer, including scaffolding/staging, working platforms, safety arrangements, surface preparation, tools, plants and all incidental works, at any height up to 25 metres, complete all as specified and as directed by the Engineer-in-Charge. |
| 47 | M&L for preparation of new corrugated, semi-corrugated, or plain steel surfaces of any description on sloped roofs or wall/cladding surfaces, over 10 cm width or girth, including surface cleaning, priming, and application of two coats of synthetic enamel paint (IN CAMOUFLAGE PATTERN), at a height up to 12 m, as per sample approved by the Engineer-in-Charge, complete all as specified and directed. |
| 48 | M&L for preparation of new corrugated, semi-corrugated, or plain steel surfaces of any description on sloped roofs or wall/cladding surfaces, over 10 cm width or girth, including surface cleaning, priming, and application of two coats of synthetic enamel paint (IN CAMOUFLAGE PATTERN), at a height above 12 m and up to 25 m, as per sample approved by the Engineer-in-Charge, complete all as specified and directed. |
| 49 | M&L for preparation of existing corrugated, semi-corrugated, or plain steel surfaces of any description on sloped roofs or wall/cladding surfaces, over 10 cm width or girth, including surface cleaning, priming if required, and application of one coat of synthetic enamel paint (IN CAMOUFLAGE PATTERN), at a height up to 12 m, as per sample approved by the Engineer-in-Charge, complete all as specified and directed. |
| 50 | M&L for preparation of existing corrugated, semi-corrugated, or plain steel surfaces of any description on sloped roofs or wall/cladding surfaces, over 10 cm width or girth, including surface cleaning, priming if required, and application of one coat of synthetic enamel paint (IN CAMOUFLAGE PATTERN), at a height above 12 m and up to 25 m, as per sample approved by the Engineer-in-Charge, complete all as specified and directed. |
| 51 | COMMON NOTES TO ITEM NO 03 AND SUB ITEMS THEREOF:- (1) The quoted rates shall be deemed to include the cost of all tools and plants (T&P) such as scaffolding, ladders, ropes, welding and cutting equipment, drilling machines, safety harnesses, lifelines, helmets and all other necessary safety gear and protective measures required for execution of the work at all heights, including working at heights up to 25 metres above ground level or as actually required at site.(2) The quoted rates shall also be deemed to include all fixing accessories, consumables and incidental items such as self-drilling screws with EPDM washers, G.I. anchor bolts, nuts, bolts, cleats, screws, rawl plugs, sealants, welding electrodes, fasteners and all other materials required for proper completion of the work in all respects, including incidental cutting, drilling, welding, removal of minor welded or bolted connections, safe lowering, stacking and removal of dismantled materials from site.(3) The contractor shall ensure adequate safety arrangements for all personnel engaged in the work and shall be solely responsible and liable for the safety of his workmen during execution, dismantling or installation operations. The Department shall bear no responsibility for any accident, injury or loss of life, and the contractor shall indemnify the Department against all such claims or damages.(4) In case the planned MS structure, truss, grill, purlin, bracing, roofing arrangement or similar work differs from the existing structure, proper measurement of the existing structure to be dismantled shall be recorded in the Measurement Book (MB) duly signed by the Engineer-in-Charge. (5) Painting has been bifurcated due to difference in height, access conditions, safety provisions and execution methodology. Item No. 1 covers normal height works as per SSR, whereas Item No. 2 covers high-level truss painting up to 21 m requiring special staging and safety arrangement.(6) Camouflage Painting, wherever mentioned, shall be carried out in a camouflage pattern as per the new Sigma pattern generated by the Station Authority, with RGB values varying from 110 to 171, using 4 to 5 colour shades in any proportion required to achieve the desired pattern and shades. The contractor’s quoted rate shall be deemed to include all work, materials, labour, scaffolding, and any other related activities necessary to complete the item as specified, and no additional claim shall be entertained during the currency of the work. |
| 52 | REPAIRS TO BRICKWORK, PLASTERING AND FINISHES |
| 53 | Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and directed. |
| 54 | Demolition of Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc. Incl removal of debris from site complete all as specified and directed. |
| 55 | M&L for Brick Work with Fly-AshBricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and directed. |
| 56 | M&L Brick work using Serviceable Bricks obtained from Item No. 4.02 here-in-before including removing old Mortar, Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in cement mortar 1:6 complete all as specified and directed. |
| 57 | M& L for brickwork with sub class \"B\" fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed. |
| 58 | M&L for Rendering (Internal) 12mm thick in cement mortar 1:6 on Brick Walls or on Concrete Surfaces, Plastered Surfaces finished Even and Smooth without using Extra Cement complete all as specified & directed. |
| 59 | M&L for preparing New/Undecorated Plastered Surfaces of Walls, applying a coat of suitable cement primer followed by a Coat of 2.0 mm thick Wall Putty (in two layers of 1mm thick) including rubbing down with Sand Paper to obtain a smooth finish surface and finishing with Two Coats of Acrylic Distemper (as approved) as per desired shade/tint complete all as specified and as directed. |
| 60 | M&L for 15 mm thick plastering in cement mortar 1:4, on external surfaces ofbrick/stone walls or concrete surfaces finished even and fair upto 4 storey height including necessary scaffloding complete all as specified and directed. |
| 61 | M& L preparing for old concrete/ plstered surfaces of any description over 10cm girth or width, not otherwise described applying two coats of Synthetic Enamel Paint over a coat of suitable Primer complete all as specified and directed by Engr-in-charge. |
| 62 | M&L for preparation of newly plastered surfaces, finished with two coats of exterior acrylic emulsion paint with anti-dust and anti-algae properties, applied over a suitable exterior primer to new wall surfaces of any description, over 10 cm width or girth, as per manufacturer’s instructions, up to 4 storeys in height, including necessary scaffolding and safety gear, complete all as specified and directed.NOTE:- Painting shall be carried out in a camouflage pattern as per the new Sigma pattern generated by the Station Authority, with RGB values varying from 110 to 171, using 4 to 5 colour shades in any proportion required to achieve the desired pattern and shades. The contractor’s quoted rate shall be deemed to include all work, materials, labour, scaffolding, and any other related activities necessary to complete the item as specified, and no additional claim shall be entertained during the currency of the work. |
| 63 | REPAIRS TO FLOORINGS, RCC SLABS ETC |
| 64 | Dismantling Floor, Paver Tiles, Hearth or Wall Tiling,etc. including Cement Mortar Bedding (but not backing) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed. |
| 65 | M&L Vitrified ceramic tiles, 9–10 mm thick (square/rectangular), double charged, light-coloured shade, with area of each tile not exceeding 0.36 m², in floors, etc., set in neat cement slurry, laid over and including 15 mm thick screed bed in cement mortar 1:4, tiles fixed with spacers to provide a uniform spacing of 3 mm between tiles, and after setting of screed bed and tiles, removing the spacers and filling the joints with suitable cementitious grout (as per manufacturer’s recommendations) complete all as specified and directed.NOTE : Cost of cement screed bed, spacers, and cementitious grout shall be deemed to be included in the quoted rate. |
| 66 | M&L Vitrified ceramic tiles, 9–10 mm thick (square/rectangular), double charged, light-coloured shade, with area of each tile not exceeding 0.36 m², in vertical surfaces, e.g., skirting, etc., set and jointed in neat cement slurry and laid over and including 10 mm thick screed bed in cement mortar 1:4. Tiles to be fixed with spacers to provide a uniform spacing of 3 mm between tiles, and after setting of screed bed and tiles, removing the spacers and filling the joints with suitable cementitious grout and pointing as per manufacturer’s recommendations, complete all as specified and directed.NOTE: Cost of cement screed bed, tile spacers, and cementitious grout shall be deemed to be included in the quoted rate. |
| 67 | M&L for providing non-skid/matt finish Ceramic tiles, coloured, 7-8 mm thick (Square / rectangular), area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqmin Flooring, set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the tiles laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate. |
| 68 | M&L for Coloured Glazed Ceramic Tiles in vertical surface 450mm X 350mm X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the Tiles, laid over and including 10mm thick rendering as Screed or backing coat of wall tilein Cement Mortar 1:3, complete all as specified and directed.NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate. |
| 69 | M&L for Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar, removal of debris outside AF land, cleaning of area to remove dust, loose particles, washing with water complete all as specified and directed. |
| 70 | M&L for providingGranite (of any type) Slab, 16-18mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement and admixture of pigment to match the shade of granite stone including edge moulding, grinding and polishing, laid over and including 20 mm thick screed bed in cement mortar (1:4), laid in any position / location complete all as specified and directed.NOTE : Cost of Cement Screed Bed shall deemed to be included in the quoted rate. |
| 71 | -ditto- but for Granite (of any type) Tiles, 16-18mm thick machine cut, in skirting/dado, fixed over and including 10mm thick cement screed (1:4) and jointed with grey cement slurry, and pointed with white cement and admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.NOTE : Cost of Cement Screed Bed shall deemed to be included in the quoted rate. |
| 72 | Demolition Cement Concrete (Reinforced) of kitchen slab, and similar work (reinforcement cut as required to facilitate demolition) and removing debris, etc. to Outside MOD Land, complete all as specified and directed. |
| 73 | M&L Reinforced Cement Concrete 1:2:4 type B0 (12.5mm graded stone aggregate) as in Shelves, Chajja, Facia, Sunshade and Similar Items and smooth finishing at Top side using extra Cement, complete all as specified and directed.(NOTE: MS reinforcement & Formwork shall be measured and paid seperately) |
| 74 | M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed. |
| 75 | M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm widefor rough finished surfaces complete all as specified and directed |
| 76 | M&L TMT Bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hoping for Columns, hooking Ends and binding with and incl Mild Steel Wire (annealed) not less than 0.9mm dia or securing with Clips, complete all as specified and directed. |
| 77 | Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed. |
| 78 | M&L for Cement Concrete 1:2:4 type B0 (12.5mm graded stone aggregate) as in Coping, Bed Plates, Holdfast, Bed Block, Kerb Stonesincluding necessary Formwork and weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. |
| 79 | REPAIRS TO JOINERY, CABINETS, GLAZING, BIRDPROOFING ETC |
| 80 | Taking down damaged / unserviceable Steel / Wooden Chowkat or Frame exc. 1.50 Sqm but not exc. 4.00 Sqm Each with shutter(without taking off shutter from the frame) and removal from site incl cutting holes in brickwork for removal of holdfasts complete all as specified and directed. |
| 81 | Taking down Shutters of any description exc 1.0 sqm and not exc 2.0 Sqm each, keeping aside for re-use or removal from site complete all as specified and directed. |
| 82 | S&FPressed Steel Frame of size 105x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates including providing necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and directed.NOTE: The pressed steel door frame under this item shall be provided to receive a steel shutter/steel door in place of a conventional wooden shutter, which shall be measured and paid for separately. The quoted rate shall be deemed to include all necessary cutting, drilling, welding, and incidental works required to make the frame suitable for fixing and smooth operation of the steel shutter/steel door, complete all as specified and as directed by the Engineer-in-Charge. No extra claim shall be entertained. |
| 83 | S&F Pressed Steel Frame of size 125x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates including providing necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and directed.NOTE: The pressed steel door frame under this item shall be provided to receive a steel shutter/steel door in place of a conventional wooden shutter, which shall be measured and paid for separately. The quoted rate shall be deemed to include all necessary cutting, drilling, welding, and incidental works required to make the frame suitable for fixing and smooth operation of the steel shutter/steel door, complete all as specified and as directed by the Engineer-in-Charge. No extra claim shall be entertained. |
| 84 | M&L Cement Concrete 1:3:6 type C0 (12.5mm graded stone aggregate) as in Filling Back side of Chowkats and for filling holdfast holes in brickwork finished even and smooth complete all as specified and directed. |
| 85 | S&F sheet glass 4.8 mm thick, ordinary quality, and glazing with oil putty in square, exceeding 0.50 sqm in each pane, in windows / fixed ventilators / fixed steel sections over doors, complete all as specified and as directed by the Engineer-in-Charge. |
| 86 | S&F in repair scratch- and strain-free 18–19 mm thick PVC board (weight not less than 9 kg/m²) for kitchen cabinets (shelves, doors, etc.), laminated on one side, joints made using PVC solvent adhesive, and fixed with self-tapping aluminium screws. Includes providing and fixing stainless steel L-shaped hinges suitable for PVC board (minimum 2 per door leaf) to hold cabinet doors, and stainless steel silver-chrome door handles, 100 mm long (1 per door leaf), complete all as specified and directed.NOTE: Quoted unit rates are inclusive of PVC board, handles, hinges, screws, and all accessories. |
| 87 | M&L for removal of damaged horizontal mortice lock from normal steel door and supply, installation, alignment, testing and commissioning of new stainless steel horizontal mortice lock, including all fasteners and fittings, complete all as specified and directed. |
| 88 | M&L for removal of damaged bottom panel of normal steel door and supply, installation and fixing of moisture-proof, termite-resistant composite/PVC/phenolic resin board, minimum 10 mm thick, thickness as approved by Engineer-in-Charge, including sealant, finishing and commissioning, complete all as specified and directed |
| 89 | S&F in repair anti-bird nylon net, machine-made, square mesh, black/blue colour, manufactured from high-density polyethylene (HDPE), UV stabilised, wire thickness not less than 1.00 mm, twine breaking strength not less than 22 kg, knot breaking strength not less than 28 kg and mesh breaking strength not less than 18 kg, 380 denier / 15 ply, including 4.0 mm dia HDPE UV-stabilised monofilament border rope, fixed to RCC/brick masonry/steel sheet or steel framework by drilling holes and fixing with suitable screws, bolts, hooks or clamps, at a height of 16.0 m and above, including all necessary scaffolding, ladders, safety arrangements, tools and accessories, complete all as specified and as directed by the Engineer-in-Charge.MAKE: GARFIL / TUF ROPES / SS ROPES / BIRDNET.NOTE:The work shall be executed at a height of approximately 18 metres. The quoted rate shall be deemed to include the cost of all machinery/equipment (including hydra, boom lift or equivalent access systems), scaffolding, safety gear, and arrangements required for safe execution of the work at such height. No extra claim on this account shall be admissible at any stage. |
| 90 | REPAIR TO PLUMBING AND SANITARY WORKS |
| 91 | Taking up or down water supply tubing, any type, 15/20mm bore (dia) with accessories, segregating Serviceable Pipes and Fittings/ Connections and keep in Safe Custody for re-use, complete all as specified and directed. |
| 92 | S&F Chlorinated Polyethylene Chloride (CPVC) pipes 20 mm outside dia, SDR-11, having thermal stability for hot and cold water supply incl all SDR-11 CPVC plain and brass threaded fittings (such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connectoretc) fixed/laying walls, ceilings or in floors etc.with suitable size MS clamp of spacing 1.00 mtr etc pipe line complete all as specified & directed. |
| 93 | -ditto- but with 25 mm outer dia size CPVC pipes |
| 94 | S&F in repair PVC (SWR) 75 mmfloor trap plain with grating including jointing to waste pipe, fixed in cement concrete 1:2:4 (20 mm graded stone aggregates) complete all as specified and directed. |
| 95 | S&F in repairs PVC (SWR) 75mm OD Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, laid onfloor, trench etc or fixed to Walls with PVC clips complete |
| 96 | S&F in repairs PVC (SWR) 110mm OD Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, laid onfloor, trench etc or fixed to Walls with PVC clips complete. |
| 97 | S&F in repair PVC (SWR) 75mm OD, Bend any type, provided with Access Door, etc. and jointing with Solvent Cement, complete all as specified and directed. |
| 98 | S&F in repair PVC (SWR) 110mm OD, Bend any type, provided with Access Door, etc. and jointing with Solvent Cement, complete all as specified and directed. |
| 99 | S&F in repair stainless steel Grating Round 100mm dia with waste hole jointing with Solvent Cement complete all as specified and as directed. |
| 100 | S&F in repair Vitreous China, white, half stall urinal flat back with grating and union for discharge pipe (excluding flush pipe and flushing cistern and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed.(NOTE: Quoted rate shall be deemed to include for the cost of waste coupling and waste pipe) |
| 101 | S&F in repair brass chromium-plated urinal spreader, including connection to the existing push/angle cock using the existing connecting pipe, complete all as specified and directed. |
| 102 | S&F in repair Vitreous China wash basin, white, flat back, size 550x400mmprovided with 32mm dia Brass Chromium Plated Waste Fitting, PVC waste pipe, brackets incl making good disturbed Surfaces in Cement Mortar 1:3 and filling joints with whte cement complete all as specified and directed.(NOTE: Cost of CP waste coupling and PVC waste pipe is deemed to be included in the quoted rates) |
| 103 | S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, with \"P\" or \"S\" trap front or back inlet, fixing bolts (except flushing cistern and flush pipe) incl plastic water closet seat cover (white) and mild steel chromium plated or aluminium hinging device complete all as specified and directed. |
| 104 | S&F in repair chromium plated Hand shower (health faucet), ABS body with 1.2 metre long flexible tube in chrome finish with wall hook complete all as specified and directed. |
| 105 | S&F in repair Jet Spray with Connection Pipe 15mm bore (dia), Brass Chromium Plated and suitable for Wash Down Water Closet Pan (Pedestal Pattern) , complete all as specified and directed. |
| 106 | S&F in repair angle valve, 15 mm bore, cast copper alloy, chromium plated fancy type, concealed type with wall flange fixed to iron pipe complete all as specified and directed. |
| 107 | S&F in repair Chromium plated brasstwo way Angle valve, fancy type,concealed type with wall flange fixed to 15 mm bore of Iron pipe, complete all as specified and directed. |
| 108 | S&F in repairs, chromium plated brass Tubular towel rail, 20mm dia,600 mm long between flanges including brass chromium plated brackets complete all as specified and directed. |
| 109 | S&F in repairs toilet paper holder, chromium plated, surface type with flapcomplete all as specified and directed. |
| 110 | S&F in repair Chromium plated brass Bib cock with wall flange, long body, fixed to 15 mm bore of Iron pipe complete all as specified and directed. |
| 111 | S&F in repair Chromium plated brass Pillar tap, with aerator, fixed to wash hand basin, complete all as specified and directed. |
| 112 | S&F in repair 15mm bore chromium plated single lever central hole basin mixer without popup waste system with 450mm long copper pipe and brass nut, complete all as specified and directed. |
| 113 | S&F in repair Stop Cock 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type with long Shank and Cup (Concealed type), screwed down, high pressure, with Crutch or Butter-fly Handle, screwed Both Ends for Iron Pipe or for Unions complete all as specified and directed. |
| 114 | S&F in repair PVC Connection Pipe 15mm size and 60 Cm in length with Adapter Nuts of PVC, complete all as specified and directed. |
| 115 | S&F inrepairs for waste coupling chromium plated for sink / wash basin, suitable for 32mmdia waste pipe complete all as specified and directed.(NOTE: This item shall only be measured for replacement in existing sinks, basins etc) |
| 116 | S&F in repair PVC Waste Pipe 32mm bore (dia), 60-75 cm length (as required at Site), complete all as specified & directed. (NOTE: This item shall only be measured for replacement in existing sinks & basins) |
| 117 | M&L removal of accumulated silt/soil, along with grass, bushes, or vegetation, if any, from the beds of saucer drains, surface channels, and side open drains of BPs (up to 20 cm depth). Includes excavation and removal of material from the sides of the drain to a distance of 100 m from the site, complete as specified and directed.NOTE:-(1) Length of drain in running meters (RM) shall be measured for payment.(2) Rates for removal of grass, shrubs, or vegetation from inside the drain are included; no extra depth shall be measured for the height of vegetation removed. |
| 118 | M&L removal of accumulated silt/soil, along with grass, bushes, or vegetation, if any, from the entry and sides of BPs (depth of deposit up to 30 cm). Includes excavation and removal of material from the sides of the drain to a distance of 100 m from the site, complete as specified and directed.NOTE:-(1) Volume of soil (in cubic meters) shall be measured for payment.(2) Rates for removal of grass, shrubs, or vegetation are included; no extra depth shall be measured for the height of vegetation removed. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
