|
| 1 | Taking down chowkats or frames with shutters (without taking off shutters frome the frames) n exc 1.5 but each complete all as specified & directed. |
| 2 | Taking down chowkhat with shutter without taking off shutte from the frame exc 1.5 Sqmand not exc 4 Sqm each complete all as specified & directed. |
| 3 | Taking down shutter of any n exc 01 sqm but n exc 2 sqm each and removing from site complete all as specified and directed. |
| 4 | M&L for mild steel framed work as in door frames andgauge shutters made of angle or hallow/square/rectangular/circular section and other covering door to be prepared for handing or sliding with including either hooks , praporsonaly made sliding door bolt , hingesor handlesfittings (inclusive of steel or othr covering, running rails and guides) and hanging also fastening and fixing , necessary arrangements i.e. flat , self tapping screws for fixing of wiremesh, necessary bolting including welding comlete conforming to FE-290 Gde E-165.Wire gauge will be measured and paid separately complete all as specified & directed. |
| 5 | S&F 35 mm thickFactory made plain framed panel shutter of 2nd class hard wood with two panel with commercial ply woodfaceveeners, seasoned nd chemically treated complete all as specifed and directed. |
| 6 | M&L for factory made 2nd class hard wood glazed and skelton door shutter made out of stiles & rails of 30mm thick 2nd class hard wood, klin seasoned and chemically pressure treated & open reabted and prepared to receive glass/gauge etc (without sash bars), edges of framing plain,chamfered of rounded, fitted with and mitred beads for securing glass etc compelte, the SIze of members of shutter shall be as per IS-1003.The shutter shall be fitted to the chowkhats complete all as specified & directed. |
| 7 | Providing and fixing factory made uPVC wooden finish colour (approved by Enger in Charge) casement (openable)Doormade of extrudedprofiles with wall thickness of 2.3mm (+/0.2mm). door profile with hollow section with multi chamber, frame (60mmx58mm),sash (60mmx78mm),T profile (One vertical length in between two shutters) (60mmx74mm) Glazing bead(35mmx20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drianage of water etc. making arrangement for fixing of hardware EPDM gasket 1.2 + -0.2 mm thick galvanised steel frame (28mmx21.5mm) sash (31mmx27.5mm)\"T\" profile (27mmx17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fastners.Hardware : [ casementhandle made of zinc alloyed (while powder coated) Butt hinges of zinc alloyed (color powder coated approved by Enger in charge) transmission gear made of mild steel with multi point locking system)and 5mm thick glazing with selected quality glass. (Note : The unit rate quoated by contractor including cost of 5.5mm glassdirection including cuttings, grooves, film/frusted if required etc. (d) membrane bonded completely to the substrate & the over laps are them sealed/fused. |
| 8 | S&F factory made Box type steel window 1.25mm thick box type ERW hollow P section of size 60mm x25mm single rebated comprise of gauged skelton shutter ERW size 50mmx20mm and 1.25 mm thick with two openable leafconsisting two Nos sash bars of T- section20mmx3mm welded to frame with one vertical mullion of ERW box type T- section of size 60mmx25mm and 1.25 mm thickincluding cutting holes and making good dismantled portion with PCC (1:2:4) type B-1 (four Nos for each window)including following fittings weled to frmae shutter:-(a) Hold fast 150mm long of 12mm x3mm made to shape -04 Nos per window.(b) Handle of z section 20mmx25mm, 100mm long - 01 Nos per leaf.(c) MS Tower bolt 150mm long -02Nos per leaf.(d) Z-section 20mmx25mm 100mm long01 Nos per leaf.(e) MS pintol hinges of size 75mmx12mm-02 Nos per leaf.Note :(i) Fabrication & fixing shall be as per TD Drawing (ii) Wire mess and painting shall be measured and paid separatly under respective items. |
| 9 | All as per srl item No 8.00 but window with glazed shutter complete all as specified & directed. |
| 10 | S&F in repair factory made steel ventilator (Box type) with side hung shutter including hinges, stel peg stay , handle and peg stay complete with glazing bars dovetailed or welded incl fixing of lugs in PCC 1:2:4 type B1 using 20mm graded sone aggregate and making good walls and ceiling to match the existing and incl hinges and handles complete all as specified and directed |
| 11 | S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified & directed. |
| 12 | S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane complete all as specified and directed. |
| 13 | Hacking out old broken glass of any thickness/size & any description from wooden or steel frame fixed with clips/putty/wooden beading and S&F with 3mm thick ordinary sheet glass fixed with clips and oil putty/wooden beadingcompleted in squares not exc 0.50 Sqm each pane all as specified and as directed. |
| 14 | S&F frame work such as grills,gratring etc,with ends of bars shouldered &/or riveted or forged into spikes,framed guard bars, barred iron door, ladder,frame balusters,walk ways, railing,frame work or water tanks, cooler stand & SImilar work conforming to Fe-290 Gde E-165 complete all as specified & directed. |
| 15 | S & F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified & directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ®Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 16 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved designpasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges paid separately) |
| 17 | S&F Stainless Steel alloy with galavanisied mild steel hing pin Butt hinges100mm long complete all as specified & directed. |
| 18 | S&F in repairs retractable door hinge including all the necessary screws and welding for fixing and including all the activities to make the door workable complete all as specified & directed. |
| 19 | S&F in repairs mild steel butt hinges medium weight colod rolled of size 100mm, ISI marked complete all as specified and directed. |
| 20 | S&F SS sliding door bolt with hasp,staple (bolt type) 300mm longnot less than 12mm dia with and incl minimum of06 bolt and nuts four on bolt plate and two on staple plate complete all as specified and directed. |
| 21 | S&F in repairs SS sliding door bolt with hasp,staple (bolt type) 300mm longnot less than 12mm dia with and incl minimum of06 bolt and nuts four on bolt plate and two on staple plate complete all as specified and directed |
| 22 | S&F 150mm floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and directed |
| 23 | S&F in repairs 150mm floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and directed |
| 24 | S&FAluminium barel tower bolt 300mm long complete all as specified & directed. |
| 25 | S&F in repairs Aluminium barel tower bolt 300mm long complete all as specified & directed. |
| 26 | S&F Aluminiumhandle of 150mm sizecomplete all as specified & directed. |
| 27 | S&F in repairs Aluminiumhandle of 150mm sizecomplete all as specified & directed. |
| 28 | S & F in repairs 125 mm long mild steel, steel window handle incl nuts & bolts ( all as per sample kept in GE office) (including welding if required )complete all as specified and directed by Engineer-in-Charge. |
| 29 | S&F aluminium frame powder coated any colour(minimum thickness of powder coating 50 micron) for doors, windows, partician, ventilators with one or more rebates including joining cleat for fixing etc. including taking down each chowkhats or frames with shutters (without taking off shutters from the frames) complete all as specified & directed. |
| 30 | S&F powder coated aluinium dooranodised of approved colour( size of frame :63.5mx38.10mmx2mm thick & size of shutter :door vertical (style ) with gasket of size 46.3mmx45.00mmx 1.50mm thick, top rail of size 47.00mmx45.00mmx1.30mmlock rail/middle rail 83.00mmx44.50mmx1.65mm thickbottom rail 114.3mmx45.00mmx1.50mm thick including S&F of5 mm thicksheet glass withglazing clip, pvc track gasket ,EPDM rubber gasket on glass of weather tightening alongwith recessed type handle,hingees, mortic lock, door stopper, door closer and including all fittings and fixtures complete all as specified as per TD -2004/61R sheet No 1/1 |
| 31 | S&F powder coated aluinium window having three track section 92mmx31.75m shutter section 40mmx18mm mounted on bearing to slide on track plain anodised of approved colour including S&F of5 mm thick frosted/plain glass and wire mesh with glazing clip, pvc track gasket ,EPDM rubber gasket on glass of weather tightening alongwith recessed type handle and lock including sealing gap with marble /granite surfacewith silicon sealent aking it water proof in all manner complete all as specified and directed by Engineer in Charge . |
| 32 | S&F Aluminium windowsmade of 1.59 thick powder coated (thickness of powder coating not less than 50 micron) as per aluminium section of size given below .Aluminium window will be of double shutter ofglass/ wire gauge shutters including allnecessary accessoriesjointing cleats , glazing clips, rubber neoprene packing, for fixing glass/ wire gauge,aluminium handles and tower bolt 2 Nos 100 mm ‘D’ Type in each door, 2 Nos 100 mm aluminium hinges including necessary steel screws complete all as specified and directed.The size of different aluminium section to be used is as under (a) Outer Frame 125X25X1.50 mm thick (b) shutter frame section size 45X44X1.8 mm thick for glass and 44x25x159mm for wire gaugeNote: Rates quoted are inclusive all fittings and fixtures. |
| 33 | Supply and fix in repairs sheet glass 5.5 mm thick of selected quality (tinted glass) exc. 0.5 sqm each fixed to aluminium frame work with necessary rubberbeading including making good complete all as specified and directed by Engineer in Charge. |
| 34 | Taking down existing aluminium doors and refixing the same opening after easing, adjusting and resecuring rubber beads, gasket beadingincluding repair to door closer, floor spring and other fittings etc complete all as directed by Engineer-in Charge |
| 35 | S&F in repair stainless steel drapery rod of 20mm inner dia (in length as directed) of approved colour with & including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with PVC rawal plug & steel screwes on walls/beams complete all as specified & directed. |
| 36 | Supply and fixing rubber door seal 32mm wide wide with aluminium strip of size 19mm wide fixed with machine steel screw with washer fixed in repair complete all as specified & directed. |
| 37 | S&F in repair plain filletsof 2nd class hardwood clean sawn square/rectangular or triangularor bullnosed or rounded on one edge area n exc 3 sqcm complete all as specified & directed. |
| 38 | S&F in repairgalvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with and includingwooden beading complete all as specified & directed. |
| 39 | S&F in repair Mortice lock of brasss bodyvertical type, size 100 mm complete all as specified and directed |
| 40 | Supply and fixing in repairsmild steel cupboard shutter with frame,Made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock, vertical type, size 65mm, 4 Levers with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12mm dia bolt 150 mm long grouted in brick wall/concrete including making good the disturbed surfaces as original, including taking down complete all as specified and as directed.Note :- The measurement shall be taken of front elevation and not girthwise. |
| 41 | S&F in repair Alumninium (extruded ) body Door closer hydraulically regulated, designation No. 2,universal type, suitable for door shutters of 701 o 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed |
| 42 | S & F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed |
| 43 | S&F in repair for factory made 18mm(+0.7mm) thik celuka PVC Ply of density 600kg/cbm manufactured by an ISO-900-2008 certified company.One side prelam and other side plain 18mm thick Celuka PVC ply for kitchen cabinet shutter and also manufacturer\"s test report and test certificate is mandatory with each and every supply of the materail Taking down of old /unserviceable kitchen cabinet / Cupboard incl all fixture and fittings. For measurement front area in elevation will be measured only complete as per directions of Engineer-in-charge,manufecturer\"s specifications and drawingcomplete all as specified and directed by Engr-in- Charge. Note : Items like cupboard knobs/handle, magnet, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing. |
| 44 | S&F in repair for factory made 18mm(+0.7mm) thik celuka PVC Ply of density 600kg/cbm manufactured by an ISO-900-2008 certified company.Plain 18mm thick CelukaPVC Ply for Shelf/Partitions/Drawer and also manufacturer\"s test report and test certificate is mandatory with each and every supply of the materail complete as per directions of Engineer-in-charge,manufecturer\"s specifications and drawing. |
| 45 | S&F in repair for factory made 5mm thik PVC sheet of density 600kg/cbm manufactured by an ISO-900-2008 certified company.Plain 5mm thick PVC sheet paneling for back side(wall side) and also manufacturer\"s test report and test certificate is mandatory with each and every supply of the materail complete as per directions of Engineer-in-charge,manufecturer\"s specifications and drawing. |
| 46 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc any height including necessary MS scaffolding complete all as specified and as directed by the Engineer-in-Charge. |
| 47 | M & L for brick work with fly ash bricks of class designation 7.5 and non-modular size as per IS 12894: 2002, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed. |
| 48 | M&L brick work with fly ash bricks, straight or curved on plan to any radius inhalf brick thick walls built in CM 1:4 complete all as specified and directed by Engr In Charge. |
| 49 | Taking down cement of cement lime plaster of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc upto any height (approx 25 Meter) including necessary MS scaffolding complete,including necessary MS scaffolding complete all as specified and as directed by the Engineer-in-Charge |
| 50 | M&L for rendering 15mm thick on fair faces of brick work or stone surfaces (Cement plaster 1:4) finished even and smooth without using extra cement at upto any height (approx 20 Meter) including necessary MS scaffolding complete all as specified and as directed by the Engineer-in-Charge |
| 51 | M&L for rendering 15mm thick on fair faces of brick work or concrete or stonesurfaces (Cement plaster 1:6) finished even and smooth without using extra cement at any height including necessary MS scaffolding complete all as specified and as directed by the Engineer-in-Charge |
| 52 | M&L for rendering 5mm thick cement mortar (1:3) as in ceiling, soffit of staircase, chhajjas facia etc including cement slurry etc at any height including necessary MS scaffolding complete all as specified and as directed by the Engineer-in-Charge. |
| 53 | M&L for preparation of new plastered surfaces of walls,and applying two coats of distemper oil emulsion over a coat of primer incl 3mm thick elastomeric wall care putty on walls complete and specified and as directed by engr-in -charge. |
| 54 | M&L for prepration ofold plastered or unplastered surfaces of walls and applying two coat of approved shade of oil emulsion distemper with 3mm thick elastomeric wall care putty on walls, including repairing of pot holes and cracks with putty, take it plaster where it required complete all as specified and directed by Engr-in-Charge. |
| 55 | M & L for preparing new plaster surfaces of walls including chajjas, facias etc. and applying premium acrylic smooth exterior paint (100% acrylic) with silicone additives in two or more coats, that offers an anti-algal, excellent resistance to ultraviolet radiation, dirt pick up resistance (DPUR) property, rich sheen, low VOC, of approved shade over a coat of primer as per the manufacturer’s instructions, applying using brush, keeping the gap/ the interval in subsequent coats, including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed. Note: - The paint shall be as per Apex Ultima of Asian Paints or equivalent of Make mentioned under Appendix \"B\". |
| 56 | Material & Labour for prepration ofold plastered or unplastered surfaces of walls andand applying two coat of exterior emulsion paintover a coat of primer any tint (colour as approved by GE) over 2 mm putty including preparation of surface of wall, band/chajja/balcony complete all as specified and dircted by Engineer in charge. Note: - The paint shall be as per Apex Ultima of Asian Paints or equivalent of Make mentioned under Appendix \"B\". |
| 57 | M&L for prepration ofold plastered or unplastered surfaces of walls and applying two coat of cement base paint , complete all as specified and directed by Engr-in-Charge. |
| 58 | M&L preparation of new plastered or unplastered surface and applyingthree coats ofwhite wash on ceiling complete and all as specified and directed by engr-in -charge. |
| 59 | M & L preparation of oldplastered surface and applying two coats of white wash on ceiling complete and all as specified and directed by engr-in -charge. |
| 60 | M&L Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide/ zinc chromate complete all as specified and directed by Engr In Charge. |
| 61 | Preparation of oldpainted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge. |
| 62 | M&L Preparation of new wooden surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primercomplete all as specified and directed by Engr In Charge. |
| 63 | M&L two coats of synthetic enamel paint including prepration of old wooden surfaces complete all as specified and directed by Engr In Charge. |
| 64 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality 5mm glass,mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engr In Charge. |
| 65 | S&F in repairs PVC cabinet mirror of size 470 mm x 570 mm x 120mm complete all specified and directed by Engr-in-Charge. |
| 66 | S&F in repairs stainless plate rack of size 900mmx750mmx250mm depth size made out of 0.75mm thick sheet complete all as specified and directed by Engr In Charge. |
| 67 | S&F in repairs CP tubular Towel rail , 20 mm dia, D Type600mm long between flanges brass chromium plated withscrews andcleats, (Minimum weight 190 gms) complete all as specified and directed by Engr In Charge. |
| 68 | S&F in repair stainless steel sink with drainage board made out of 1mm thick sheet for kitchen or laboratory with plug, washer, waste pipe etc including cast iron brackets, connecting union over all size 915mm X 460mm with bowl size 410mm X 330mm X 160mm including ss coupling, pvc waste pipe and dismentling complete all as specified and directed by Engr In Charge. |
| 69 | S&F in repairS&F sinks made of stainless steel 1 mmthickkitchenor laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm includingss coupling, pvc waste pipe and dismentling complete all as specified and directed by Engr In Charge. |
| 70 | S&F in repairs steel Grating doom 125 mm dia with waste hole or without hole complete all as specified and directed by EIC |
| 71 | S&F in repair 100mm bore PTMT sink/WHB waste coupling fixed to waste pipe and wash hand basincomplete all as specified and as directed by Engineer-in-Charge. |
| 72 | M&L in repairs ofPVC waste pipe 75mm long, 32/40 mm bore complete all as specified & directed. |
| 73 | S & F in repairs fancy type 15mm diaBrass CP wall mixer/basin hole mixer/sink mixer for mixing hot & cold water screwed down for iron pipe complete all asspecified and directed |
| 74 | S&F in repairs soap dish, Stainless steel approximate size 160x160x90mmfixed to plugs with chromium plated brass screws etc complete all as specified and directed by Engr In Charge. |
| 75 | S&F in repairs glass shelf consisting of 5.5 mm thick sheets glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr In Charge. |
| 76 | Demolition of existing roof treatment of any description including cement plaster, roof padding, APP Membrane and cement tiles any thickness from the roof surfaces of buildings including cleaning of top surfaces in all respect and preparing for further treatment and taking out and removing the rubbish, debris outside MoD land complete all as specified and as directed. |
| 77 | S & F chicken wire mesh in hexagonal shape, mesh size 25 mm, wire dia 0.71 mm complete all as specified and as directed. |
| 78 | Material & labour for rendering 20 mm thick in cement mortar 1:4 over RCC Roof mixed with water proofing compound @ 3% by weight of cement or manufacturer instruction finished even and fair complete all as specified and as directed. |
| 79 | M & L for preparing RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particle and applying three course water proofing treatment with APP modified bituminous water proofing membrane with polyester reinforcement and plain finish of 3 mm thick (total weight of the finished membrane not less than 3.8 kg/ sqm ± 5 % per sqm) confirming to IS 16532: 2017 consisting of first course of bitumen primer conforming to IS 3384: 1986 @0.40 litre per sqm, second courses of bonding material of industrial bitumen of grade 85/25 conforming to IS 702: 2022 @ 1.20 kg per sqm and third course of APP membrane and including sealing all joints, overlapping etc. using Butane Torch as per Annex D of IS 16540: 2017 complete all as specified and as directed. |
| 80 | M & L for cutting grooves or chase in brick wall, 75 mm wide and 65 mm deep and including filling with cement mortar 1:4 mixed with water proofing compound as mentioned in Annex D of IS 16532: 2017, IS 16540: 2017 complete all as specified and as directed. |
| 81 | M & L for applying two cots of heat reflective high SRI (solar reflecting index) paint having minimum SRI of 108 as per ASTM E 1980, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strictly as per manufacturer\"s specifications and as approved by the Engineer-in-Charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc., washing with water all complete. The contractor shall give guarantee for the performance of SRI and also the durability of coating, complete all as specified and as directed. Note: (a) The product shall have been included in the GRIHA Product catalogue. |
| 82 | M & L for bitumastic gola, with 85/25 industrial grade bitumen and coarse sand mixture. 1:3 by weight, 8 cm X 8 cm at the junction of roofing to vertical surfaces complete all as specified and as directed. |
| 83 | Demolition of cement concrete in sunken portion in any position not otherwise specifically provided for complete all as specified and as directed by Engineer-in-Charge. |
| 84 | Providing and making fillet of cement concrete in 1:2:4 in sunken portion, complete all as specified and directed by Engr In Charge. |
| 85 | Refilling Lime concrete with brick aggregate (Course) in lime mortar1:3, 300mm thick in the sunken with the help of proper tools & equipments & plants complete all as specified and as directed by Engineer-in-Charge. |
| 86 | Providing and making cement concrete in 40mm thickness in 1:2:4 type B0 (12.5mm graded aggregate) mixing Dr Fixit Pidiproof LW+. Complete in sunken upto the below level of tiling including necessary spout pipe complete all as specified and as directed by Engineer-in-Charge. |
| 87 | Disconnecting existing Rotational moulded polythylene water tanks (cylindrical vertical with closed top) of capacity Exc 250 litres & n exc 500 litres setting aside ( or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position complete all as specified & directed. |
| 88 | Dismantling exc 250 but n.exc 500 litre capacity water tank and remove from site complete all as specified and directed by Engineer-in-Charge. |
| 89 | All as per srl item No 88.00 but exc 500 ltrs and n. exc 1000 ltrs. |
| 90 | S&F in repairs 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical verticle with closed top) hoisted and fixed in position including float valve and all necessary tank fitting complete all as specified in SSR Part-I |
| 91 | S&F in repairs 1000 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical verticle with closed top) hoisted and fixed in positionincluding float valve and all necessary tank fitting complete all as specified in SSR Part-I |
| 92 | S&F in repairball brass valve high pressure with polythene float and nut confirming to IS screwed for iron pipe or brass ferrule 20mm bore complete fixed in repairs complete all as specified & directed. |
| 93 | S&F in repair 25mm bore Gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified & directed. |
| 94 | Taking up or down 15 mm bore steel tubingand connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge :- |
| 95 | All as per srl item No 94.00 but 20mm bore. |
| 96 | S&F in re tubing medium grade with all fitting and fixing complete to wall/floor and ceiling etc for |
| 97 | All as per srl item No 96.00 but 20 MM bore |
| 98 | Taking down/dismantling loose/damage concrete including plaster of any description and in any position from RCC structures like chajja, fins, roof ceiling, louvers, parapet, column, beam, and of lintel by hammering with wooden mallets carefully chipping off the old concrete surface with necessary scaffolding including cutting of rusted reinforcement if so required and removal of debris to a distance not exceeding 500m complete all as specified and as directed. |
| 99 | Cleaning the existing surface of concrete and reinforcements as obtained after execution of item No.97 here in before by wire brush including scrapping & cleaning with emery paper and washing down with water as required and M&L for applying “Solvent free epoxy concrete bonding agent” as per manufacturer’s instructions on old concrete surfaces for bonding with new concrete complete all as specified and as directed.Make : Nitobond EP of FOSROC/Carbodur of SIKA/ or equivalent in PIDILITE |
| 100 | M&L for Applying two coats of “Epoxy zinc rich primer” as protective coat to expose surface of old and new reinforcement over 10 mm dia as per manufacturer\"s instructions complete all as specified and as directed. Make : Nitozinc primer of FOSROC/Friazinc R of SIKA/ or equivalent in PIDILITE |
| 101 | M&L for rendering 15mm thick on any faces of brick work or concrete surfaces in cement mortar 1:6 mixed with Dr fixit pidicrete URP @ 15% by weight of cement finished evenand smooth without using extra cement after applying one coat of cement mixed with Dr fixet pidicrete in 1:1 ratio as a bonding coat between plaster and old brick surface or concrete surfaces complete all as specified and directed. |
| 102 | Dismentling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed. |
| 103 | S&F solid PVC wall lining consisting of 5mm thick wood grainprinted PVC sheet inclusive of solvent cement and fixing at site on PVC frame, complete all as specified and directed. |
| 104 | S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed. |
| 105 | M&L for false ceiling with Armgyp-FB ceiling tiles of size 595 x 595mm, 9mm thick (as approved by GE) fixed with and including galvanized iron powder coated inverted \"Tee\" or \"L\" section (concealed GI frame work) suspended from ceiling with provision of galvanized wire 4 mm dia and wall taping screw including butterfly clips, hold down clips for fixing the board to frame complete all as per manufacturer’s instructions, complete, all as directed and specified.(a)Size of grid - 610 x 610 mm.(b)Size of main Tee – 39 x 24.70 x 0.80 mm.(c)Size of cross Tee – 39 x 24.70 x 0.80 mm.(d)Size of wall angle – 22.20 x 22.20 x 0.65 mm. |
| 106 | M & L for75 mmthickPCC 1:3:6 type C1 as in Plinth Protection/path/hard stanging using20 mmstoneaggregateincludingmakingjoints & fillingwithsandbitumen mastic as per complete including dismentling all as specified and directed by Engr In Charge. |
| 107 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge |
| 108 | M&L for Non-SkidColoured Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified anddirected by the Engineer-in-Charge . |
| 109 | M&L for Screed bed or bedding layer 15 mm thick in CM (1:6) for laying floor finishes/ paths etc., complete all as specified and directed by Engr-In-Charge. |
| 110 | M&L forvitrified ceramic tiles 9 to 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match etccomplete all as specified and directed by Engr-In-Charge. |
| 111 | M&L forVitrified Ceramic tiles light shade/ /double charge/ ultracharged 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etccomplete all as specified and directed by Engr-In-Charge. |
| 112 | All as per srl item No 111.00 but in dado/Skirting over 10mm thick rendering in CM 1:4 |
| 113 | M&L Glazed ceramic coloured tiles in vertical surface 300X 450X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchinclback plaster 10 mm thick in cm 1:4 complete all as specified and directed by Engr In Charge. |
| 114 | M&L for Rendering or bedding layer for tiles as in vertical surfaces 10 mm thick in CM (1:4) for back coat. Complete all as specified and directed by Engr-In-Charge. |
| 115 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid,bedded and pointed in any mortar complete all as specified and directed by Engr-In-Charge. |
| 116 | M&L for Screed bed or bedding layer 20 mm thick in CM (1:6) for laying floor finishes/ paths etc., complete all as specified and directed by Engr-In-Charge. |
| 117 | M&L for 16-18mm thick Graniteincluding cutting polishing rounding on edge etcmachine cut, bedded andjointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including grinding and polishing (Color aproved by Engr-in-charge) complete all as specified and directed by Engr-In-Charge. |
| 118 | M&L Machine pre polished cut kota stone slab 18 mm(+-2mm) thick and jointed with grey slurry mixed with pigment to match the slab including rubbing and polishing as per complete all as specified and directed by Engr In Charge. |
| 119 | M&L Machine pre polished cut marble stone 18 mm(+-2mm) thick and jointed with grey slurry mixed with pigment to match the slab including rubbing and polishing as per complete (Color aproved by Engr-in-charge) all as specified and directed by Engr In Charge. |
| 120 | S&Fpre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as specification including dismentling complete all as specified and directed by Engr In Charge. |
| 121 | S&Fpre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as specification including dismentling complete all as specified and directed by Engr In Charge. |
| 122 | M&L for Chequered cement concrete tiles with grey cement and pigments 20cm x20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with 15mm thick bedding layer of cement sand mortar (1:6) including 100mm thik cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base for floors finishes including dismentling complete all as specified and directed by Engr In Charge. |
| 123 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement allincluding dismentling complete all specified and directed by Engineer-in-Charge. |
| 124 | S&F precast machine pressed PCC interlocking paver block of 80 mm thickness, M-40 grade of any shape and size confirming to IS -15658-2006 with grey cement and pigment as approved and 100mm thick plain cement concrete, type D-2, 1:4:8,(using 40mm graded stone aggregate) as in sub base flooring, surface finished even and rough to receive floor topping including sand cusion and dismentling complete all as specified and directed by Engineer-in-Charge. |
