Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | SCHEDULE \"A\" PART I (B/R WORKS)Demolition of cement concrete unreinforced of any type any level and at any position and removal of the demolished material outside MD land complete all as specified. |
| 2 | Taking down cement plaster of any description in any positionincluding racking out joints making key scrubbing down with water etc. and removal of debris out side MD land. |
| 3 | M&L 15mm thick plastering in CM 1:6, on fair faces of brick work or concrete surfaces and provn of 3mm thick wall care putty on plastered surfaces of wall; surfaces finished even and smooth with out using extra cement complete all as specified and directed. |
| 4 | M & L for dubbing out with CM 1:4 average 15mm thick on irregular face of walls complete all as specified and directed |
| 5 | M & L forcement plaster 20 mm thick in CM 1:4, two coats using factory manufactured pre mix/ready mix of \"Roofit Mix\"of M/s Premier Floor to Roof Materials pvt.ltd/ \"Easy plast\" of M/s Walplast Products pvt.ltd/ \"Readiplast\" of M/s Ultratech Cement Ltd/\"Soundplast PMC-1\" of M/s Sound buildcare pvt.Ltd/, Randeroc ready plaster of makefosroc with integral water proofing compound \"Conplast WL Xtra of makeFosroc\" or other approved equivalent make, having minimum composition of C:S :: 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechnIcal mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 15 mm thick and finishing coat of 5 mm thick final rendering,including using richer mix for making corners if necessary, including water proffing powder at 3 % of cement at all floors and level, including making grooves of existing size wherever required, including providing chicken wiremesh 100mm x 100mm size at RCC & brick in joints , including cleaning the surfaces, curing etc. complete all as per specifications & as directed by the EIC note: water proofing powder will be measured and paid seperately |
| 6 | M&L for rendering 5 mm thick on ceiling using factory manufactured pre mix/ready mixplaster of \"Roofit Mix\" of M/s Premier Floor to Roof Materials Pvt Ltd/\"Easy plast\" of M/s Walplast Products Pvt Ltd/\"Readiplast\" of M/s Ultratech Cement Ltd\" / Soundp last PMC-1 of M/s Sound build care Pvt Ltd, Randroc ready plaster of make Fosroc with integral water proofing compound \"Conplast WL Xtra of make Fosroc\" or other approved equivalent make, having minimum composition of C:S : 1:3 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering in ceiling, having low rebound properties, low water demand for curing properties mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over concrete surfaces, curing etc. complete all as specified & directed by Engineer-in-Charge . |
| 7 | Demolition of brick work built in CM incl. taking out roots vegetation if any at any position and removal to out side MD land |
| 8 | M&L for brick work with sub class \"B\" bricks straight or curved on plan exc. 6m mean radius built in CM(1:6) complete all as specified. |
| 9 | S&F for Pre- Painted galvalume aluminiumzinc coating AZ-150 GI basedcorrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping ,drilling ofscrews/suitable lengthGI \"J\" or \"L\" hooks in roofcomplete all as specified and directed. |
| 10 | S&F for roof trusses (framed) trussed, Purlins, crane gantries, rails and fastenings and heavy brackets framing(Beam, Angle, Channel or flat section,plain plates) including distance pieces, cleats ,welding and braceing etc,Fe-410W(Gde-E-250)quality -B,including necessary scaffolding etc complete all as specified and directed. |
| 11 | M&L painting with synthetic enamel paint of two coats over a coat of red oxide primer on new steel surfaces of any description exc. 10 Cm width or girth including prepation of surfaces. |
| 12 | Taking down chowkats without taking off shutters from the frame area n. exc 1.50 Sqm each complete all as specified and directed. |
| 13 | Taking down chowkats without taking off shutters from the frame exc.1.50 Sqm and not exc. 4.00 Sqm |
| 14 | S&F stainless steel butt hinges medium weight 100mm long. |
| 15 | S&F aluminium anodised barrel tower bolts of extruded section 150mm long. |
| 16 | S&F alluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast alluminium alloy and fixed of length of bolt 300 mm |
| 17 | M&L extruded aluminium alloy handles, fabricated type, anodised 150mm size. |
| 18 | M&L udaipur green marble slab 18-20 mm thick in treads and window cill/jamb/soffits (provided in two layers with overlap) & length will be as per the length of windows)and similar work machine cut, bedded and jointed with grey cement slurry over and including 10 mm thick screed bed in cement mortar 1:4 and pointed with white cement using marble dust with admixture of pigment to match the shade of marble slab including grinding and polishing complete (Note : The rates include the cost of cement screed bed 10 mm thick) |
| 19 | S&F forpowder coated aluminium section in frame or shutters of window , doors and partitionwith aluminium section ( medium weight) of suitable size as directed by Engineer-in-Charge, cut to size, jointed together with cadmium plasted steel screws and all necessary fitting, screw, plug for fixing screws locking arrangement etc complete all as specified and directed.Note:- The rate ofglass pane, wire mesh will be measured and paid separately. |
| 20 | S&F 4.8mm thickglass ordinary quality and glazing with oil putty in in square n exc 0.5 sq. m in each pane complete all as specified. |
| 21 | S&Fanodised aluminium grill DG- 102 of Deco grill or equivalent fixed with \"F\" section size not less than 1mm thick of approved make all as specified and directed by Engr-in-CHarge. |
| 22 | S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed. |
| 23 | S&F solid PVC door frame(chowkhat) of size 50mmx47mm made out of 5mm plain dark colour PVC sheet reinforced with MS square tube etccomplete all as spd and directed. |
| 24 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top& bottom rails.MS frame shall be covered with heat moulded plain dark colour PVC \"C \"Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain dark colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail& bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with suitable PVC sheet beading and joined together with solvent cement, etc fixed to frame complete all as spd and directed. |
| 25 | S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor of 140mm size |
| 26 | M&L prelaminated particle board, exterior grade, 18 mm thick, prelaminated one sides with decorative choice lamination & other side balancing white lamination, fixed with aluminium cleats to aluminium frame work |
| 27 | M & L 5.5 mm thk Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane |
| 28 | M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed |
| 29 | M&L WC connector 110 mm PVC SWR for WC complete all as specified and directed. |
| 30 | Supply only PVC connector 15mm size with PTMT nuts of length 450mm |
| 31 | M&L PVC valveless, syphonic action type, 10 ltrs cap flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe 32mm dia and fixed in repairs complete all as specified and directed. |
| 32 | M&L PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 33 | S & F Mirror 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plughs with chromium plated brass screws and cup washers in repairs complete all as specified and directed. |
| 34 | M&L Wash basin, Vitreous China white (Flat back) 630 x 450mm including brackets,, pinning in ends of brackets or erecting stand including fixing of waste pipe and pillar type etc ( Suppy of pillar tap and waste pipe shall be measured separately) complete all as specified and directed. |
| 35 | Supply only pillar tap 15 mm bore cast copper alloy chromium plated fancy type complete all as specified and directed. . |
| 36 | M&L waste fitting of 32 mm bore, brass, chromium plated for glazed ware wash basin etc with long screwed shanks and fly-nuts flange end bedded in red lead cement and other end fixed |
| 37 | M&L stop valves 15mm bore dia, cast copper alloy fancy type, chromium plated with long shank and cup concealed type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions in repairs complete all as specified and directed. |
| 38 | M&L bib tap brass 15mm bore dia chromium plated long shank fancy type with curtch or butterfly handle , screwed down, screwed for iron pipes completein repairs complete all as specified and directed. |
| 39 | S&F in repairs brass chromium tubular towel rail 20mm dia, \"D\" type, 60cm long between flanges. |
| 40 | S&F stainless steel soap dishes of required size all as complete and specified as directed by Engineer-in-Charge. |
| 41 | M&L Glass Assembly sheet glass consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracked guard and railing 60cm long in repairs complete all as specified and directed. |
| 42 | Taking down steel tubing 20mm bore of pipe and connectionsincluding cleaning for refixing etc as required complete all as specified and directed. |
| 43 | S&F 20mm bore U- PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings completed all as specifiec and directed. |
| 44 | M&L Rotational moulded polyethylene water storage tanks (Cylindrical verticval with closed top) hoisted & fixed in position in repairs all as specified of 2000 ltrs capacity complete all as specified and directed.. |
| 45 | M&L in repairs Ball valve high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete.25mm dia complete (minimum weight 25mm-455gms) all as specified and directed. |
| 46 | M&L Nipple suitable for HDPE water tank (minimum weight 25mm - 65 gms) 25mm bore dia complete all as specified and directed |
| 47 | S&F in repairs 25 mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed |
| 48 | Dismantling floor, hearth or wall tiling including cementmortar bedding (but not backing), removing serviceable tiles and rubbish off the premises etc complete all as specified and directed. |
| 49 | M&L Vitrified Ceramic tiles (light shade) of size 600mmx600mmx8-9mm thick (square/ rectangular) polished, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and including 15 mm thick cement screed base (1:6) (Note : The rate includes the cost of cement 15 mm thick screed bed) |
| 50 | M&L Vitrified Ceramic tiles (light shade) of size 600mmx600mmx8-9mm thick (square/ rectangular) polished, in vertical surfaces (dado/skirting) etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and including 10 mm thick cement plaster (1:4) (Note : The rate includes the cost of cement 10 mm thick cement plaster) |
| 51 | M&L glazed ceramic jointless coloured tiles in vertical surface 450 x 300 x 7mm thick set and jointed in neat cement slurry over and including provision of bedding layer 10mm thick in CM 1:3 complete all as specified and directed.(Note : Cost of 10 mm thick bedding is included in the rate). |
| 52 | M&L Non - skid coloured ceramic tiles of size 300mm x 300mm x 6 to 7 mm thick in floors over and including 15 mm thick screed bed in cement mortar 1:4 etc. set and jointed in neat cement slurry complete all as specified and directed by Engr-in-Charge. |
| 53 | S&F fancy type aluminium alloy curtain rail fixing with pair of brackets, stops, rollers etc complete all as specified and directed. |
| 54 | M&L for applying one coat of primer Dr Fixit Prime seal after an interval of 4 hrs then applying 2 coats of Dr Fixit Raincoat star throughly cleaning, washing and saturation of surface with water and filling of external hairline cracks upto 5mm with Dr Fixit Crack-X Paste including necessary erecting & dismentaling of scaffolding complete all as specified and as directed. |
| 55 | M & L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with roller over one coat of alkali resistant primer .etc complete all as specified and directed . |
| 56 | M&L for preparation of new plastered surfaces of ceiling and applying two coat of oil bound distempercomplete all as specified and directed |
| 57 | M & L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete. complete all as specified and directed by Engr-in-Charge. |
| 58 | M & L for post construction anti termite treatment by treating the soil along with external perimeter of building at the rate of 2.25 Litre of emulsionn per meter of the perimeter wall complete. |
| 59 | M & L for post construction anti termite treatment of soil under existing floors using chemical emulsion at the rate of one litre per hole, 300mm apart including drilling andplugging 12mm dia holes with cementmortar 1:2 to match the existing floors |
| 60 | M & L at points of contact of wood work by chemical emulsion (in oil or kerosine based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degrees at 150mm centre to centre and sealing the same complete. |
| 61 | M&L for application of wall treatmentincl surface preparation opening of cracks andapplication of cementbased coat as per manufactoring instructions having min service life of 5 years warranty and completeall as specified and directed by Engr-in Charge . Make : Thermacool or Dr Fixit or AsiaPaints or Techno Commercial Equivalant |
| 62 | M&L for application of roof treatmentincl surface preparation opening of cracks and application of cement based coat as per manufactoring instructions having min service life of 10 years warranty and completeall as specified and directed by Engr-in Charge . Make : Thermacool or Dr Fixit or AsiaPaints or Techno Commercial Equivalant |
| 63 | Hermetically sealing automatic sliding doors with Door Blade of Thickness minimum 40 - 48 mm size 1800 x 2100mm.The door surface should be made up of HPL of thickness at least 3mm thickness on both the sides with fire retardant PUF core sandwiched between EN 438 Grade Antimicrobial HPL, with viewing window of size 300 x 400 mm. Air permeability test results according to NF EN 1026 standard specifications. The door should be mounted on the rail of high-grade AS1 aluminium extrusion profile to carry any door weight (till size 1800mm X 2100mm) with minimum 6mm deep indentations to ensure perfect hermetic sealing. Automation must be Microprocessor based, 230 V, 50-60 Hz, 40 W (Max. 500W). 40 Vcc, mounted on guide rail, connection to control box via plug-in cable. Infrared Radar Sensor for safe operation and obstruction sensing.The doors should be operable by switch (on either side of OT). The opening and closing speed should be customizable from 0.1 to 0.5 m/sec.• Having a special inside & outside Stainless-Steel D Type handle that lifts out the door blade from its hermetic closing position, thus allowing even very heavy doors to be opened effortlessly, manually. • The door frame should be made of high-quality anodized aluminium extrusion & with concealed fixings that are adjustable during installation to ensure that 100% hermetic seal is achieved. The door panel should be encased within an extruded powder coated 2.5 mm thick aluminium profile frame all around the door blade with solid high-pressure laminate on both sides that can withstand high abrasion. To ensure efficient sealing of the door’s frames should be provided.• Should have special nylon top rollers with double roller bearings, to enable the door to slide smoothly & silently and should be fixed to the door in such a way they do not obstruct trolley movement through the door.• Vision panels - double glazed, laminated safety glass, flush finished on both sides with door blade should be provided in the doors. 300 x 400mm • The automation controller for the door should be microprocessor based with regulated electromechanical sliding door drive. • The automation should be able to operate a door with maximum door weight of 220Kg. • The automation / door can be controlled/operated using either Hand Sensor (touch less – infrared switch) OR Touch less foot Switch. All doors should be able to be operated easily manually in the event of failure of the power supply or the automation unit controller.The Equipment should be CE-certified as per Medical Device Directive (93 /42/ EEC) and should have a Quality Management System as per ISO13485Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 64 | Hermetically sealing automatic sliding doors with Door Blade of Thickness minimum 40 - 48 mm size 900 x 2100mm.The door surface should be made up of HPL of thickness at least 3mm thickness on both the sides with fire retardant PUF core sandwiched between EN 438 Grade Antimicrobial HPL, with viewing window of size 300 x 400 mm. Air permeability test results according to NF EN 1026 standard specifications. The door should be mounted on the rail of high-grade AS1 aluminium extrusion profile to carry any door weight (till size 1800mm X 2100mm) with minimum 6mm deep indentations to ensure perfect hermetic sealing. Automation must be Microprocessor based, 230 V, 50-60 Hz, 40 W (Max. 500W). 40 Vcc, mounted on guide rail, connection to control box via plug-in cable. Infrared Radar Sensor for safe operation and obstruction sensing.The doors should be operable by switch (on either side of OT). The opening and closing speed should be customizable from 0.1 to 0.5 m/sec. • Having a special inside & outside Stainless-Steel D Type handle that lifts out the door blade from its hermetic closing position, thus allowing even very heavy doors to be opened effortlessly, manually. • The door frame should be made of high-quality anodized aluminium extrusion & with concealed fixings that are adjustable during installation to ensure that 100% hermetic seal is achieved. The door panel should be encased within an extruded powder coated 2.5 mm thick aluminium profile frame all around the door blade with solid high-pressure laminate on both sides that can withstand high abrasion. To ensure efficient sealing of the door’s frames should be provided.• Should have special nylon top rollers with double roller bearings, to enable the door to slide smoothly & silently and should be fixed to the door in such a way they do not obstruct trolley movement through the door.• Vision panels - double glazed, laminated safety glass, flush finished on both sides with door blade should be provided in the doors. 300 x 400mm • The automation controller for the door should be microprocessor based with regulated electromechanical sliding door drive. • The automation should be able to operate a door with maximum door weight of 220Kg. • The automation / door can be controlled/operated using either Hand Sensor (touch less – infrared switch) OR Touch less foot Switch. All doors should be able to be operated easily manually in the event of failure of the power supply or the automation unit controller.The Equipment should be CE-certified as per Medical Device Directive (93 /42/ EEC) and should have a Quality Management System as per ISO13485Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 65 | Hermetically sealing type of manual swing/ sliding door having thickness of 40-48mmof size 900 x 2100mm single leaf with PUF core sandwiched between AntimicrobialHigh Pressure Laminates (HPL), with viewing window of size 300 x 300mm. The door leafs hung on exturded heavy duty aluminium alloy extursion door framefor single side swing doors. |
| 66 | Hermetically sealing type of manual swing/ sliding door having thickness of 40-48mmof size 1500 x 2100mm single leaf with PUF core sandwiched between AntimicrobialHigh Pressure Laminates (HPL), with viewing window of size 300 x 300mm. The door leafs hung on exturded heavy duty aluminium alloy extursion door frame for single side swing doors. |
| 67 | Hermetically sealing type of manual swing/ sliding door having thickness of 40-48mmof size 1200 x 2100mm single leaf with PUF core sandwiched between AntimicrobialHigh Pressure Laminates (HPL), with viewing window of size 300 x 300mm. The door leafs hung on exturded heavy duty aluminium alloy extursion door frame for single side swing doors. |
| 68 | Integrated Window - The integrated winodw should bemade oftwo toughenedglasses fof 6mmthicknesshavingan air gapof 29mm in between the twoglasses withinside framenmmade ofstainless steel/ Aluminum(Silver Anodised). THe DGU window shall beflush mountedwith wall panels. It shouldbe aligned with existingwindow and made of suitablesize (1200 x 1000mm)for each theatreafter consultation with concerned department. Integratedvenetianmotorised blinds shouldbe provided for openingor closing. It shallbe motorised window and shall comewith remote control.Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 69 | Scrub Sink,2-Bayscrub sink should bedesigned for use in operation theatre complex providing surgeonswitha convenientsink for pre-OT scrb. It should bemade upofstandardsize of 1.5mm thick stainless 304 grade. The scrub sink shall have touchless operation through infrared photo sensor. Itshall have adjustabledigital timer with setting of 1,3,5,10 minutes. It shouldthe thermostaticcontrolvalve and solenoid valve. THe scrub sink should beprovidedwith frontaccess panel forease of maintenance and repairs and have anti splash design.Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 70 | S & F Lockers (male/ female)complete all as specified and directed by Engineer-in-Charge. As per sample andspecifications to beapproved by user before execution.Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 71 | Storage Cabinet System• Approximate dimensions shall be 1800 H x 1000 W x 300 D mm. Storage Unit shall be flush mounted and made up of at least 1mm thick AISI Stainless steel (304 grade). • The storage shall have design feature of construction with back-to-back sheets to avoid any bacteria contaminations. • Storage shall be finished with Anti-bacterial powder coating with added silver ions and complementing the color theme of the OT wall panelling. • Storage doors with 6mm clear toughened Glass shall have design feature of opening by minimum 165 degree to ensure easy cleaning of the side edges of the doors. • At least three numbers of adjustable shelves shall be provided with height adjustable clamps. Storage doors shall be provided with three-point lock. • Round D-handle shall be provided to easy and better cleaning. Storage unit shall be provided with suitable height adjustable plinthNote : Being specialisednature of item, sample should approved by user and GE before execution |
| 72 | Dirty utility roomsluice sink in stainless steel 304 alongwith faucets. Floor/wall mounted and size as per site requirement . As per sample and specifications to be approved by user before execution.Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 73 | Storage Racks of Stainless Steel Size: 1800 Lx500 D x 1800 H mm complete all as specified and directed by Engineer-in-Charge. As per sample andspecifications to beapproved by user before execution.Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 74 | Working table of Stainless Steel Size: 915 W x 570 D x 1340 H mm complete all as specified and directed by Engineer-in-Charge. As per sample andspecifications to beapproved by user before execution.Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 75 | S&Fstainles steel sink with drainage board ,1 mm thick sheet of steel grade AISI 304 for kitchen or laboratory, with plug, waste pipe, washers including CI cantilever bracket, connecting union etc., overall size 915 x 460 mm with bowl size 410 mm x 330 mm x 160 mm including supply and fixing bib tap CP with long body screwed for iron pipe complete all as specified and directed. Make : Nirali, Bule star or Tecno Commercial equivalent.Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 76 | Writing Board (List Board) Size: about 950mm x 650mm Writing board should be made of ceramic having Magnetic properties and should be flushed to the wall of the operation room. Note : Being specialisednature of item, sample should approved by user and GE before execution |
| 77 | 1. Stainless Steel Prefabricated Walls & CeilingsThe wall elements should be made of 0.8 mm thick, 4-fold folded stainless steel (SS 304 / X5 CrNi1810, 1.4301 according to DIN|EN 10088) cassettes with plasterboard (DIN|EN 18180), 15 mm thick, glued to the inside of the cassettes. The standard wall elements must have a grid size of 1,200 mm; few panels may be customised as per the site conditions to accommodate corner panels. The bended cassettes should also tide closed at the corners.Distance between the operating room walls should be variable and sufficient to accommodate flush mounted equipment. The gap between the inner and outer walls should be with minimum obstructions for the possible addition of equipment at a later stage to enable services, pipes, conduits etc, to be run within the gaps. All wall-mounted equipment should be flush mounted. The wall panel design and construction should allow for the installation and support of all equipment and the provision of openings required for installations, without affecting rigidity and strength. There should not be any sharp edges and corners. A shell type substructure should be designed as a non-load bearing wall. This substructure should be made of galvanized steel of 1.5mm – 2.00 mm thick on which the prefabricated SS wall panels should beinstalled.. The floor rails should be mounted by using proper mounting mechanism like clamp plates profile with screw and threaded rods with dowel the unfinished floor to even out the unevenness of the floor.Preferred OR height to be planned as 2800-3100mm from False Ceiling to finished floor. The three-part wall panels should be planned as 900 mm lower element, 200 mm as middle element & upper wall element based on the room height so that replacement is easier in case of up gradation. The individual wall panels should be installed with removable clamps/ screws fastening system which will allow fast installation / uninstallation for service. Wall Panel welding will not be permitted and the joints should be covered with removable & reusable silicone gasket such that there is continuity in walls visually. Liquid silicone should not be used for sealing. Provision / cutout for Control Panel, Large Display Monitor’s or any other Built-in elements as per customer requirement shall be provided from factory. These cutouts preparation will not be allowed at site. The prefabricated wall panels should be antibacterial/ antimicrobial powder coated based on epoxy-polyester painted at the factory only. Colour Shade of coating should be confirmed with the user department. |
| 78 | Test Certificate from a Third-Party NABL Accredited lab shall be submitted.It should have a high heat stability and durable against mopping and steam. Resistance against common hospital cleaning and disinfection agents must be ensured. Antibacterial Coating Test: The antibacterial/antimicrobial Powder Coating should confirm as per JIS Z 2801:2010 or EN ISO 22196 Fire Test: The Modular Wall Panel shall come with a Standard Fire Rating & comply with ASTM E-84 Test Certificate from a Third-Party NABL Accredited lab shall be submitted. Harmonized coating: For an entire harmonized appearance, wall elements should be coated at the same factory. Printed wall panel: According to users choice, at least 2 Steel wall panels (2400mm x 1900mm or as per OT height) should be printed at factory level. It shall be factory printed and no site pasting. The printing should be protected by an additional clear lacquer. Metal Cassette Ceiling:Snap fit ceiling tiles shall be made up of at least 0.7mm thick AISI Stainless steel (SS 304 / X5 CrNi1810, 1.4301 according to DIN|EN 10088) cassettes at height of 3100mm. The OEM shall have CE compliance certificate on ceiling systems. Ceiling Tiles shall be coated with antibacterial/ antimicrobial powder coating with added silver ions. The use of Silver ions in powder coating shall provide 24-hour protection against bacteria, fungi and mold, including against Staphylococcus aureus resistant to methicillin, Salmonella, Pseudomonas and Legionella colon. The antibacterial/ antimicrobial properties should confirm as per JIS Z 2801:2010 or EN ISO 22196. Test Certificate from a Third-Party NABL Accredited lab shall be submitted.Grid Size: The tiles shall be suspended on modular framework system of material - galvanized / powder coated steel suspension brackets along with threaded rod forming a grid of 1200mm x 600mm . Ceiling mounting grid shall not be visible. Ceiling installation should be secured with a locking system and perfect sealing. No screws are allowed. Room lighting, Laminar air Flow , ceiling service units , OT lights and any other ceiling units shall be integrated into the metal ceiling system. Design shall permit individual removal of panels with exceptions of those at the periphery of the operation theatre. The grid shall be rigid and remain perfectly stable during all the subsequent site operations. Suspended ceiling perimeter support profile shall be made of extruded aluminium to receive the ceiling panels. Structure shall remain stable and shall have non-slip feature even after adjustmentNotes:1. Being specialised nature of item, sample should approved by user and GE before execution.2.Quoted rates inclusiveof warranty of 10 years on antibacterial properties of coating on stainless steel 304 wall & ceiling |
| 79 | Anti- Static (Conductive) Flooring:The flooring should conform to standards, ISO 16000-6, EN 685, EN 13 501-1, EN 425, EN 423 & EN 433. It should be fire resistant, scratch resistant, chemical resistant & resistance to fungi – bacterial growth. It should be a 2mm thick homogenous conductive Vinyl flooring of approved pattern as per drawing on hard dry and dust free existing floors using sheets an approved rubber based adhesive Dunlop S-758, Fevicol SR-998 or approved equivalent including rolling with light wooden roller, The flooring should be smooth, non-slippery, impervious material conductive enough to dissipate the static electricity but not conductive enough to endanger the shock to the personnel.The flooring should either be inset mosaic with least possible joints and copper strips to carry away any static electricity produced. Conductive copper mesh should be done for tiles.A floor screed should be provided, flat to within a tolerance of +/-3mm over any 3 meter area. Copper grounding strips (0.05 mm thick, 30-50 mm width) should be laid flat on the floor in the conductive adhesive and connect to copper wire of grounding.All joints should be welded with electrodes of the same compatible material to provide a continuous sealed surface. The conductive flooring should ensure:• The protection of Electronic equipment and components • The protection of people against electro-static discharge risks • The protection of premises against explosive risks.• The Conductive tiles should be static – conductive, flexible, homogenous vinyl floor covering with an electrical resistance of 5 x 104 ≤ Rt ≤ 106 (EN 1081).The Conductive flooring should have the following characteristics:• Low accumulation of electrostatic charges to people & Equipment. • Should provide an enduring resistance to static and dynamic loads • should display excellent resistance to chemical products such as detergents, acids and alkaline products.• Low VOC emissions. • Should have Fungi static and bacteriostatic treatment throughout the total thickness of flooring. • It should be non-absorbent, impervious and non-porus. Note : Quoted rates inclusive of warranty of 10 years on antibacterial properties of coating on stainless steel 304 wall & ceiling |
| 80 | WALL PANELING : The PVC Walls covering on Wall with1.5 mm thick finished withHard PVC /Antistatic Vinyl Covering with Bioson Panel: Antibacterial/ Antimicrobial Poly Vinyl Homogeneous of thickness 2mm backed by 12mmBioson board panelon existing Wall surface. The Joints are welded and seamless. As per sample andspecifications to beapproved by user before executionNote : Being specialisednature of item, sample should approved by user and GE before execution |
| 81 | Providing & fixing false ceiling with fully perforated 12mm thick nicro tegular edges or 10mm thick square edged GRG false ceiling tiles atall heights with GRG (Glass Fibre With Semi Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in truehorizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. As per sample andspecifications to beapproved by user before executionNote : Being specialisednature of item, sample should approved by user and GE before execution |
| 82 | M & L for solid PVC Wall Lining consisting of 5mm thicksingle side prelam PVC sheetinclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as directed and speciied by Engr-in-Charge. As per sample andspecifications to beapproved by user before executionNote : Being specialisednature of item, sample should approved by user and GE before execution |
| 83 | Antimicrobial P.U Paint on Wall in Prepost Operative room: Providing 2-3 mm thick readymade special grades \"Filler and Putty\" on Wall surface to give smooth and joint less finish. Applying primer and two coats of polyurethane paint water based on all internal Wall surfaces. The system is Anti-fungal/Anti Bacterial, UV resistant, Non-yellowing in nature. Water washable and with special microbiological characteristic against bacteria. It also meets the resistance to fire propagation as per BS-476 Part VI & Part VII standards, with Class 0 & Class 1 result. Since it is a water base, it provides an environmentally safe condition. As per sample andspecifications to beapproved by user before executionNotes :-1.Being specialisednature of item, sample should approved by user and GE before execution.2.Quoted rates inclusive of warranty of 10 years on antibacterial properties of coating |
| 84 | SCHEDULE \"A\" PART I (E/M WORKS)M & L for taking down carefully copper/aluminium point wiring (light, fan socket or power) complete such as switches, ceiling rose pendents ,regulators, sockets etc removing materials to store for keeping in safe custody or for taking credit ( credit for above item should be made as per condition separately) and making good disturbed surfaces of walls , floors etc.(as per Sch of Credit) |
| 85 | M & L for taking down old unserviceable MCB DBs including MCBS |
| 86 | M & L for taking down old unserviceable Air conditioning outdoor , indoor unit and Connected copper tubeing and kept in MES store for refixing complete all as directed and specified. |
| 87 | M & L for taking down old unserviceable ceiling fan and kept in MES store for refixing complete all as directed and specified. |
| 88 | M & L for point wiring complete with proper colour coding using, 1100 Volts grade, 1.5 Sqmm, PVC insulated FRLS-H, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked with multistranded copper conductordrawnin concealedPVC conduit pipe,under the surfaces of wall, ceiling/ panel board etcwith all accessories, fittings, PVC junction boxes etc, also including 1.5 Sqmm, PVC insulated, FRLS-H, unsheathed, 1100 Volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed Note : Modular Metal Flush Box, cover plate and frame shall be measured and paid separately. Note : (i) Rates are inclusive of chasing, cutting and making good the surface on wall/roof/floors. |
| 89 | One light point controlled by one switch |
| 90 | One fan/exhaust fan point controlled by one switch |
| 91 | One 3 pin socket point 6 A controlled by switch on same board |
| 92 | One 3 pin socket point 6 A controlled by switch on independentboard |
| 93 | One bell point controlled by one switch |
| 94 | M&L for point wiring using proper colour coding with 1100 Volts grade, 2.5 Sqmm PVC insulated, FRLS-H, unsheathed, wire confirming to IS-694, Part-II, ISI marked with multistranded copper conductordrawnin concealedPVC conduit pipe,under the surfaces of wall, ceiling/ on panel board etcwith all accessories, fittings, PVC junction boxes etc, also including 2.5 Sqmm, PVC insulated, FRLS-H, unsheathed, multistranded, copper conductor 1100 Volts grade, green color, continuous earth wire connected to common earth dolly for 15 Amps, 3 Pin, socket outlet independent complete all as specified and directed. Note : Modular Metal Flush Box, cover plate and frame shall be measured and paid separately. |
| 95 | Supply & Fix Bell, AC, 230 Volts, single pole, complete all as specified and directed |
| 96 | Supply and fix modular bell push, 6 Amp, 1 module, complete all as specified and directed. |
| 97 | Supply and fix modular switch, 1 way, 6 Amp ,1 module, complete all as specified and directed. |
| 98 | Supply and fix modular switch, 1 way ,16 Amp, 1 module, complete all as specified and directed. |
| 99 | S&F ceiling rose three terminal, 230 Volts, PVC / Polycarbonate body, complete all as specified and directed. |
| 100 | Supply and fix Modular socket outlet, 6 Amps, 3 pin 2 module, complete all as specified and directed |
| 101 | Supply and fix Modular socket outlet 6A/16 Amps, 2/3 pin combined 2 module, complete all as specified and directed |
| 102 | S&F Modular AC Box With 20A/ 25A SP MCB, DBOXx MCB Combo & Unbreakable Heavy Duty With ISI Plug Top. |
| 103 | Supply and fix concealed modular metal flush box 19 SWG (1mm thick) GI coating with and including matching modular white cover plate with frame, 1/2 module, complete all as specified and directed. |
| 104 | Supply and fix concealed modular metal flush box 19 SWG (1mm thick) GI coating with and including matching modular white cover plate with frame, 3 module, complete all as specified and directed. |
| 105 | Supply and fix concealed modular metal flush box 19 SWG (1mm thick) GI coating with and including matching modular white cover plate with frame, 4 module, complete all as specified and directed. |
| 106 | Supply and fix concealed modular metal flush box 19 SWG (1mm thick) GI coating with and including matching modular white cover plate with frame, 6 module, complete all as specified and directed. |
| 107 | Supply and fix concealed modular metal flush box 19 SWG (1mm thick) GI coating with and including matching modular white cover plate with frame, 8 module, complete all as specified and directed. |
| 108 | Supply and fixingLED Peripheral Lights : Recess mounted IP54 Protocol, Non hygroscopic Peripheral Lights having power LED elements with suitable electronic driver and controls. The Peripheral light diffuser is fixed in powder coated aluminium frame (Size: 600 X 300 mm)all as specified and directed. |
| 109 | Supply and fixing LED Lights : Recess mounted IP54 Protocol Lights having power LED elements with suitable electronic driver and control. The peripheral diffuser is fixed inpowder coated Aluminum from size-600 x 600mm, glare free, 6500K all as specified and directed.(Size: 600 X 600 mm) |
| 110 | Supply and fixing LED Lights : Recess mounted IP54 Protocol Lights having power LED elements with suitable electronic driver and control. The peripheral diffuser is fixed inpowder coated Aluminum from size-300 x 300mm, glare free, 6500K all as specified and directed.(Size: 300 X 300 mm) |
| 111 | S&F in repairs of MCB TPN8 way in verticalposition includingearth & neutral link and all accessories double door, 415 Voltswith 200 rated bus barcomplete all as specified. |
| 112 | S & F MCB DB, 12 way, SPN, double door, 240 Volts, fixed concealed/ surfaces on the wall, making all connections, complete all as specified and directed. |
| 113 | Supply and fix 415 V, 10KA, C curve, MCB TPN, 63 Amp current carrying capacity in DB with connection and testing all as specified and directed. |
| 114 | S&F in repairs MCB SPN 40A rating, 230 Volt, and connecting the incoming and out going cables by using copper lugs pin type |
| 115 | S&F MCB SP 6-32 Apms, 240 Voltsall as specified and directed |
| 116 | Supply and fixing ceiling fans complete with blades, down rods, including electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor |
| 117 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep of size 250 mm x 300m |
| 118 | M&L for sub main wiring complete with Two runs of 2.5 Sqmm single core PVC insulated unsheathed,heavy duty, 1100 Volt grade multistranded copper conductor cable (FRLS) and drawnin concealedPVC conduit pipe,under the surfaces of wall, ceiling/ panel boardetcwith all accessories, fittings, PVC junction boxes etc, and including one run of PVC insulated and unshethed copper conductor 2.5 Sqmm single core cable (FRLS) as earth continuity conductor, connected with earth dolly and mains all as specified & directed. Note: Threerun of 2.5 Sqmm PVC cable and one run of PVC conduit will be measured as one unit length. |
| 119 | M& L for Taking down submain wiring andM&L for sub main wiring complete with Two runs of 4 Sqmm single core PVC insulated unsheathed,heavy duty, 1100 Volt grade multistranded and drawnin concealedPVC conduit pipe,under the surfaces of wall, ceiling/ panel board etcwith all accessories, fittings, PVC junction boxes etc and including one run of PVC insulated and unshethed copper conductor 4.00 Sqmm single core cable (FRLS) as earth continuity conductor, connected with earth dolly and mains all as specified & directed. Note: Threerun of 4 Sqmm PVC cable and one run of PVC conduit will be measured as one unit length. |
| 120 | M&L for sub main wiring complete with Two runs of 6 Sqmm single core PVC insulated unsheathed,heavy duty, 1100 Volt grade multistranded copper conductor cable (FRLS) and drawer through and including PVC conduit (minimum 20 mm dia) on the surfaces of the walls, ceiling / on paneletc with all accessories, fittings etc and including one run of PVC insulated and unsheathed copper conductor 6.00 Sqmm single core cable (FRLS) as earth continuity conductor, connected with earth dolly and mains all as specified & directed. Note: Tworun of 6 Sqmm PVC cable, one run of 6 Sqmm PVC cable and one run of PVC conduit will be measured as one unit length. |
| 121 | M & L in replacement of Earthingcomplete withgalvanizedsteelearthelectrode60Cmx 60Cm x 6 mm thick directly buried in ground ( eath pit not less than 2.25 M deep below the normal ground levelconnected togalvanized earth lead wire 4 mm dia by mains ofbolts, nuts, check nuts and washersof galvanizediron steel includingnecessary excavationearth workPCC chamberCI chamber cover protectionpipe wateringpipe etc. (Complete all as shown in electrical plate No 3 and connectedto earthing testpointcompleteincluding excavation earthwork,PCC chamber, chamber cover ,funnel watering and protection pipe etc allspecified anddirected. |
| 122 | M & L in replacement of Earthingcomplete withcopper plate earthelectrode60Cmx 60Cm x 3.15 mm thick directly buried in ground ( eath pit not less than 2.25 M deep below the normal ground levelconnected togalvanized earth strip 20 x 3mmby means ofbolts, nuts, check nuts and washersof galvanizediron steel includingnecessary excavationearth workPCC chamberCI chamber cover protectionpipe wateringpipe etc. (Complete all as shown in electrical plate No 3 and connectedto earthing testpointcompleteincluding excavation earthwork,PCC chamber,chamber cover ,funnel watering and protection pipe etc allspecified anddirected. |
| 123 | Supply and fixing copper earth stripof on wall/ floor of size 20 x 3 mm all as specified and directed. |
| 124 | Supply and fixing Galvanized iron or steel wireof on wall/ floor of size4 mm dia all as specified and directed. |
| 125 | M & L for MCCB, 4 Pole, 415 V, Adjustable type, 40 Amp, Amps with breaking capacity 16 KA with sheet metal enclosure allspecified anddirected. |
| 126 | Supply and fixing on wall,XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional 25 Sqmm , 3.5 Core (For Auto Clave machine sockets) |
| 127 | Supply and fixing on wall,floorXLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional 35 Sqmm , 3.5 Core (for DB) |
| 128 | Supply and fixing Industrial plug and wall mounted socket with industrial connector forheater having 5 Pin (3Pin +N+E) with 32 Amp of auto clave machine all as specified and directed. |
| 129 | Supply Install and testing, commissioning of UPS for 30 min back up three phase AC input 300 to 450V and out put single phase AC out put Voltage 230 V ± 1% of capacity 10KVA with batteries all as per specified. Make- Microtech – I MAXX series or equivalent in V Gurad/Luminous etc. |
| 130 | Supply and fixing Two Plate LED X-Ray Viewing Screen designed to provide a high level of control luminance without flicker. Size - 950 X 650 X 115 mm all as specified and directed. |
| 131 | Supply and fixing Surgeon Control Panel (membrane) mounted flush in the theatre wall, comprising of the following:1 No. Day Time Clock1 No. Elapse Time Clock1 Set dimmer for peripheral/ planair lights. 1 No. hands free telephone1 No. Medical Gas status/ alarm1 set indicator only for temperature and humidity displaySize - 650 X 650 X 115 mmall as specified and directed. |
| 132 | Supply and fixing Anesthesia Single Arm Pendant - The pendant shall majority constructedout of aluminum alloy. It shouldbe antibacterialpowder coated and test certificatefor thesame shall be submitted.1 x Arm 800mm1 x Drop tube having a carying capacity of maximum load of 150 kg -Rotation of 330 deg.1 x Basic Console - 600 mm1 x Fixed shelf (350x350x50 mm)1 x Adjustable shelf (350x350x50mm)6 x Mains Socket (5/15Amp)6 x Medical Gas Terminal & Hose Assembly(2 x Oxy, 2xVac, 1xAir(4bar),1xAir 7 Bar,1x N20 , Provision for AGSS,Data & A/V 2 nos.) Note:-1. Rate Including medical gas pipeline connection in Anesthesia pendent . |
| 133 | Supply and fixing Surgeon Double Arm Pendant majorily constructed out ofAluminum Alloy. It should be AntibacterialPowder coated and test cetificatefor thesame shall be submitted - Comprising of1 x Arm 800 & 1 x Arm 800 having a1 x drop tube having a carrying capacity of maximum load of 80 kg-Rotation of 330 deg.1 x Basic Console - 750 mm1 x Fixed shelf (350x350x50 mm)1 x Adjustable shelf (350x350x50mm)6 x Mains Socket (5/15Amp)6 x Medical Gas Terminal & Hose Assembly(2 x Oxy, 2xVac, 1xAir(4bar), 1xAir(7bar), 1xN2O, 1xCO2, Provision for CO2 Data & A/V 2 nos.) |
| 134 | Supply and fixing LED DUAL DOME OT LIGHTCeiling mounted Dual Dome LED OT lights ( imported and as per EN standard, y) with following features.- 160000 and 120000 lux,each Dome should have multiple steps dimming,FocusLight field dia - 180-320mm,Color temp. 4300k,Should have safety glass,Light emitting surface,Should have satin finish cover glass.Make : Draegar, Infimed, Dr Mach |
| 135 | Anesthesia Induction Room |
| 136 | Supply and fixing Two Plate LED X-Ray Viewing Screen designed to provide a high level of control luminance without flicker.Size - 950 X 650 X 115 mm |
| 137 | Supply and fixing LED SINGLE DOME OT LIGHTCeiling mounted Single Dome LED OT lights ( imported and as per EN standard, y) with following features.- 100000 lux, FocusLight field dia - 130 – 240 mm,Color temp. 4300k,Should have safety glass,Light emitting surface,Should have satin finish cover glass.Make : Draegar, Infimed, Dr Mach |
| 138 | Supply and fixing UV light for sterilization includingcomplete fitting enclosureas requiredat site all as specified and directed. |
| 139 | Supply and fixing Unidirectional Laminar Air Flow Plenum Ceiling - constructed out of 1.2 mm thick SS 304 sheet of size 1800 X 2400 mm having 6 nos of hepa filters. The hepa filters having dust spot efficiency of 99.99% 0.3 micron. Air & Light diffuser made of mono filament precision woven polyester for the plan air ceiling to give a \"LAMINAR FLOW\" of filtered air. It also provides a diffused shadow less lighting system with Intensity control all as specified and directed. |
| 140 | Supply and fixing Return air grill for existing AC plant as per OEM all as specified and directed. |
| 141 | Supply and fixing Cascade Pressure Stabilizer having multi 304 graded stainless steel blades to control room air pressure Size - 305 X 335 mm all as specified and directed. |
| 142 | Supply and fixing HVAC - Ducting inside OT\"s GI Ducting with 22-24 Gauge Sheet including all fixtures and accessories as required at site complete all as specified and directed. |
| 143 | Supply and fixing HVAC Ducting Insulation 13 mm nitrile rubber class \"O\" insulation all as specified and directed. |
| 144 | Supply and fixing HVAC Ducting Insulation 19 mm nitrile rubber class \"O\" insulation all as specified and directed. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
