|
| 1 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etcbut excluding ashlar facings,dressed stonework and precast concrete articles complete all as specified and as directed by Engineer-in-charge. |
| 2 | M&L for brick work with sub class B bricks, straight or curved on plan exc 6m mean radius built in CM1:6 complete all as specified and as directed by Engineer-in-charge. |
| 3 | Description as per srl item No 2 here-in-before but except bricks. |
| 4 | S & F (PVC (SWR) pipe 110 mm bore single socketed in any length with rubble ring joints as in weep holes all as directed by Engr -in-Charge. |
| 5 | Taking down old cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc |
| 6 | M&L for 15mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement. |
| 7 | M & L for 15 mm thick rendering onfair faces or brick work or concretesurfaces in cement mortar 1:4 surface finished even and smooth (with out using extra cement) |
| 8 | M&L applying two coats of cement based paint inclpreparation of new plastered surface complete all as specified. |
| 9 | Preparation of old decorated plastered or unplastered surfaces of walls, conices etc by brooming down, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of cement base paint all as specified. |
| 10 | Preparation of new plastered surfaces and applying twocoat of oil bound distemper on new surfaces of wall complete all as specified. |
| 11 | M&L preparing of old surfaces as on wall one coat of oil bound distemperall as directedby Engr-in-charge. |
| 12 | Preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint,desigen and pattern as approved by engineer in charge complete all as specified. |
| 13 | Taking down chowkat or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm each complete all as specified. |
| 14 | \"-ditto- as per above but exceeding 1.5 sqm n exc 4 sqm each. |
| 15 | Taking down shutters exceeding 1 sqm but not exc 2 sqm each. |
| 16 | M&L for pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc.complete , of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified |
| 17 | M&L for pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc.complete , of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified |
| 18 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings. |
| 19 | M&L cement concrete (1:3:6) type C0using 12.5 mm graded stone aggregate filling in pressed steel chowkats, bed block for holdfast and the like all as specified. |
| 20 | M&L for factory made, 2nd class hard wood rail and style 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treatedcomplete all as specified and directed. |
| 21 | S&F 2nd class hard wood, glazed and skelton shutter 35mm thick open rebated and prepared to receive glass, guage, etc. (without sash bars), edges of framing palin, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. sizes of members of shutters as specified in SSR 2009 Pt-I Section 8.24(b) supplied and fitted to chowkhats, all as specified. |
| 22 | S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading andjointed together with solvent cement supply & fixing in the frame at site. complete all as specified. |
| 23 | S&F 100mm Butt hinges,heavy weight,cold rolled mild steel and fixed in repairs. |
| 24 | S&F Aluminium anodized, barrel tower boltof extruded section, 150mm long |
| 25 | S&F in repairs Aluminium handle, cast type,anodized, 150mm size |
| 26 | S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 27 | S&F in repairs Helical door spring of size 300 mm including welding to steel chowkhats, complete all as directed at site. |
| 28 | S & Fof 150mm floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring,fixed in floor complete all as specified. |
| 29 | M&L for preparation of woodensurfacesexceeding 10 cms width or girth and applying two coats of synthetic enamel paintoveronecoat of pinkprimer complete all as specified. |
| 30 | S&F box type steel windows/Ventilator (factory made) outer frame made out ERW tube \"P\" section 65X45X25 mm and shutter of ERW tube \"P\" section 50mmX35mmX20mm openable (double shutter) with glazed shutter on extrernal side and gauzed shutter on internal sideincluding steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of \"Z\" section and its locking arrangementand mild steel hook and eyes suitable for fixing cooler /ACwindow complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3 Note:- The quoted rate a shall also include (i). One shop coat of zincchromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrte surface (ii) 4 nos MS steel lugs made of 20X5 mm Iron flat 200 mm long iii)10 mm Sq Bar grill/guard bar design as per drawing (iv) PCC block for embedding lugs |
| 31 | S&F Galvanised mild steelwirecloth 0.50 nominal dia of wire and average width of aperture 1.18mm complete all as specified |
| 32 | S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified. |
| 33 | Hacking out old broken glass of any thickness, size, quality or description from the wooden frames glazing with puttyor fixed with wooden beads complete all as specified. |
| 34 | M&L for preparation of steeland iron surfacesexceeding 10 cms width or girth and applying two coats of synthetic enamel paintoveronecoat of red oxide zinc chromeprimer complete all as specified. |
| 35 | S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc complete all as specified and minimum thickness of powdere coating 50 micron |
| 36 | S&F Powdercoated aluminium door shutters, aluminum section weighing 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screw etc complete all as specified |
| 37 | S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified |
| 38 | S&F 5.50 mm thick sheet glass fixing for Aluminium doors and windowsincluding 25 micron reflective type sun control film complete all as directed |
| 39 | M & L Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60kg and fixed as in repairs (aluminium die cast body ) |
| 40 | Dismantling CGI corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof coverings, complete all as specified andas directed by Engineer-in-charge. |
| 41 | Dismantling timber scantling 40 sq cm and over in section framed work of any description |
| 42 | S&F for structural steel works of Fe 410W (Gde E 250) quality A, as inRoof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate/red oxide primer paint (including preparation of surface) before fabrication as directed. |
| 43 | S & F 0.5mm Pre-painted galvatume aluminium Zinc coating steel GI based corrugated sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self taping screws as specified. |
| 44 | S & F 0.5mm Pre-painted galvatume aluminium Zinc coating steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self taping screws as specified. |
| 45 | Dismantlingwall and ceiling boards (fibre, pulp, insulation , etc.)or insulation boards/ slabs/ blankets any thikness including cover fillets. |
| 46 | S&F 4mm thick of size 605X605 mm, pre-premiered, self embossed, Reinforced Designer Board for false ceiling Conforming to IS-14862 and ISO-8336:1993. As per specification under mention:(i)GI section frame work (POWDER COATED) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmX19mmX0.45mm, cross \"Tee\" 28.6mm (web)X 24mm flange .33mm thick powdered coated main tee 38(Web) X24mm flange 0.33mm thick. wall angle screwed fixed to brick wall/partition wall/concrete/RCC with the help of nylon sleeves and screws @ 610 mm C/C , Then suspending GI main \"Tee\" in both directions by means ofhangers with alignment@ 1220mm C/C to soffits. To from grid of 610X610mm cross Tee shall be provided @ 610mm C/Cin both directions. Suitable provisions shall be made for fixing the recessed/surface mounting light fittings if any, complete all as specified and directed by Engr-in-Charge. |
| 47 | S&F5mm thick Prelam PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining,Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and directed. |
| 48 | S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 49 | S&F in repair Stainless steel drapery rods of 25 mm dia complete withcoloured conical end balls at both end, dia not less then 50mm and fitted with and incl MS bracket size 150mm made to shape or 75mm dia MS end wall to wall round block made to shape in male and female pieces as required at site. |
| 50 | Dismantling floors hearth or wall tiling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises. |
| 51 | M&L for colored non skid ceramic tiles7 to 8 mmthick, area of each tileexc 0.11 sqm but n exc 0.18 sqm in floors etcset and jointed in neat cement slurry and pointed in colored cement to matchshade, pattern, laying etc of tiles, over and incl 15 mm thick screed bed orbedding layers of cement mortar 1:6 as directed at site |
| 52 | M&L Glazed ceramiccoloured tiles, (Premier quality), of size 450 x 350 x 7 mm thick on vertical surfaces such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces including 10mm thick rendering inCM 1:4 all as specified & directed. Note : Design, shape and pattern of fixing of tiles shall be as directed by Engr-in-Charge. |
| 53 | M&L for Vitrified ceramic tiles 10mm thick (square/rectangular) light shade polished, area of each tiles n exc 0.36 sqm in floors etc set and jointed in neat cement slurry over and including 15mm thick screed bed in cement mortar 1:6 and pointed in white or coloured cement to match. |
| 54 | M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid 20 mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and dismantling the exisiting surface completeall as specified and directed. |
| 55 | M&L for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including screed 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and dismantling the existing surface complete all as specified. |
| 56 | M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and likelaid over and including 20mm thick in cement mortar (1:4) including roughening the exisiting surface and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified. |
| 57 | Dismantling water tanks and removing to store exc 500 & n.exc 1000 litres. |
| 58 | Rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I,capacity of water tank 1000 Ltr |
| 59 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 15mm bore of pipe. |
| 60 | S & F or tubes, \"Medium grade, galvanised, with all fittings and fixed in short lengths complete to walls and ceilings or laid in floor , 15mm bore of pipe. |
| 61 | Description all as per itemas above but fixing only (15mm bore of pipe) |
| 62 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 20mm bore of pipe. |
| 63 | S & F or tubes, \"Medium grade, galvanised, with all fittings and fixed in short lengths complete to walls and ceilings or laid in floor , 20mm bore of pipe. |
| 64 | Description all as per itemas above but fixing only (20mm bore of pipe) |
| 65 | S & F in repair 15 mm bore bib taps, fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule . |
| 66 | S & F in repair 15 mm bore stop/angle valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both endsfor iron pipe or for union.. |
| 67 | S & F in repair 20 mm bore stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both endsfor iron pipe or for union.. |
| 68 | S & F in repairs 15mm bore pillar tap fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and flynuts, screwed for iron pipe. |
| 69 | S & F for PVC connections 15mm size with PTMT nuts of length600mm. |
| 70 | S&F PVC waste pipe 32mm bore complete, all as specified |
| 71 | S & F in repairs 10 litres capacity PVC valveless , syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets. |
| 72 | S&F as in repair tubular towel rail,aluminium anodised 20 mm dia `D\" type 60 cm long between flanges |
| 73 | S&F as in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) |
| 74 | S&F in repair chromium plated shower roses 125mm longwith armswivel joints any size including fixing to steel pipe or union .complete all as specified and directed by Engineer-In-Charge. |
| 75 | S&F 600 X 450 mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 76 | S&F in repair vitreous china wash hand basin white flat back of size 550x400 mm including bracket, (pedestal pattern )cutting for and pinning the ends of brackets or erecting stands exclusive of waste pipe but including brass chromium plated waste coupling with long screwed sank and fly nuts complete all as specified. |
| 77 | S&F Hand Shower (Health Faucet) (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 78 | S&F ball valves high pressure of PTMT with appoxy coated alluminium rod and high density plastic ball screwed for iron pipe 20mm bore fixed in repair all as specified minimum weight 210grms |
| 79 | S&F 15 mm dia borein repairs brass CPmixer for mixing hot & cold water screwed down for iron pipe and fixed. |
