|
| 1 | SITC of Air Conditioning of Main Showroom 1st Floor Arts Emporium at JKHHC Srinagar |
| 2 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: 25 meter beyond 1 m from cutting edge |
| 3 | Providing and laying of nallah stone solling tightly hand packed including all carriages complete. |
| 4 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 5 | Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) Light shade using white cement. |
| 6 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for:Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 9 | 12mm Cement plaster of mix: ( 1 cement : 4 fine sand) |
| 10 | Providing and laying of chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing. One face dressedFine chisel dressed |
| 11 | Providing and laying of extra fine chisel dressed Devri Stone in curved |
| 12 | Providing and laying of fine chisel dressed Devri Stone coping with moulding etc complete in cement mortar 1: 6 (1 cement : 6 coarse sand) including curing and as per the directions of engineer in charge. |
| 13 | Providing and laying of Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shades, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints |
| 14 | Providing and laying of Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately)Size of tile 500x500 mm |
| 15 | Supply and fixing of gate value /stop cock of approved quality design as per the instructions of Engineer in charge.(100 mm N bore) |
| 16 | (60 mm N bore) |
| 17 | (20 mm N bore) |
| 18 | Supply and fixing of Anker bolts with nuts 12 mm dia including base plate with 220 mm x 220 mm and 6 mm thick complete job |
| 19 | Providing and fixing of soil, waste and vent pipes 100 mm dia. PVC including all bends , tees and other fixtures of approved quality like Prince, Vectus or like type B.100 mm dia |
| 20 | 90 mm dia |
| 21 | 75 mm dia |
| 22 | Providing and fixing of G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. including necessary tees,l-bows union.sockets C- Class completeIn let /out let 100 B. Medium (external work)100 mm dia. nominal bore |
| 23 | 60 mm dia. nominal bore |
| 24 | 50mm dia nominal borre |
| 25 | 20 mm dia. nominal bore |
| 26 | Constructing of brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 . |
| 27 | Providing and laying of kota stone in floor with different sizes (thickness to be specified by the manufacturer), with water absorptionless than 0.08%, including grouting of joints (payment for gouting of jonts to be made separately) |
| 28 | Providing and laying in position cement concrete of specified grade indludein curing but excluding the cost of centering and shuttering. All work up to plinth level with 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm nonimal size) |
| 29 | Removal of bushes/ grass for proper beautification of fountain area |
| 30 | Carriage of materials by way of mechanical means including loading, unloading and stacking of materials at siteSand for an avg lead of 8 Kms including a H.L of 50 m. |
| 31 | Stone aggregates for an avg lead of 10 Kms including a H.L of 50 m. |
| 32 | Sand for an avg H.L of 50 m. (1/3 Qty only) |
| 33 | Stone aggregates for an avg H.L of 50 m. (1/3 Qty only) |
| 34 | Dismatling of existing fountain/ concrete/ Kota stone/ tiles by way of mechanical means and removal of derbis /clearing the site as required lead upto 50mtrs |
| 35 | Supply, Installation, Testing and Commissioning of 03 HP mono submersible pump sets, with steel mounting frame, grouting bolts, SS Screen/Filter etc. Make: Standard Make Pump Casing- Cast Iron Impeller-Cast Iron Shaft-Steel Motor Casing-Cast Iron Make: Standard Make |
| 36 | Design,Supply, Installation, Testing and Commissioning of Control panel(CPRI Approved (IS/IEC:61439) comprises of a sheet metal enclosure with hinged front door, back wall mounting type with provision for incoming & outgoing cable entry.Panel comprise of motor main switch, contactors, switch fuse, MCB, push button on off switches, indicating lamps, capacitor, step down transformer, Sequencer for LED Lights etc. complete with internal wiring Standard Make. The Job further includes Outdoor Electrical Enclosure fabricated from 18 gauge MS sheet with hinged front door, back wall mounting type with provision for incoming & outgoing cable entry, 12” long legs made of iron angle with locking arrangements & provision for fixing of panel complete in all respect including cement concrete works. |
| 37 | Design, supply,fixing of GI manifold 2\"x 10′ dia ring with 75 No. of 12mm x 65mm sockets with Brass Jet Nozzles,one central foam jet made from Brass alloy. The job further includes the Providing/Fixing of other necessary items like elbows/sockets/Nipples/Valves and other plumbing items with mounting stands complete in all respect making fountain fit for services.Make of jets :Standard Make |
| 38 | Design, supply & fixing of PVC conduit Pipe with fittings, jointing material for interconnections etc Standard Make |
| 39 | Design, supply & fixing of light mounting bracket, PVC joint box, cable jointing compound, nut bolts, washer, brackets, cable tie etc.Standard Make |
| 40 | Supply, Laying, Testing and Commissioning of 2.5x3 core cable for pump connection and conduting arrangement including Excavation work.Standard Make |
| 41 | Supply, Laying, Testing and Commissioning of 2.5x4 core cable for light connection & conduting arrangement up to control room including Excavation work.Standard Make |
| 42 | Earthing of pump and panel with material & earthing wire, earth pit, earthing electrode complete in all respect.Standard Make |
| 43 | Supply, Installation, Testing and Commissioning of 18-21wx12v WPL 100 LED Light SS Waterproof luminaries with array of high output of LEDs housed in compact enclosure, with elastomeric seal. Special polyamide cable gland. Compact socket head fasteners and mounting bracket. The housing, top cover and bracket,fasteners of stainless steel. Standard Make |
| 44 | Supply installationTesting and Commissioning of 4 Core 35 mm sq. Al armored XLPE cable withstand voltage of 650/1100V standard make |
| 45 | 4 Core 50 mm sq. |
| 46 | Supply/Laying of DWC Pipe of 75mm dia Standard make |
| 47 | Supply, Laying, Testing and Commissioning of 1.5 mm sq copper wire single core for light connection internal & conduting arrangement up to control room including Excavation work.Standard Make |
| 48 | Supply, Laying, Testing and Commissioning of 6 mm sq copper wire single core for light connection external & conduting arrangement up to control room including Excavation work.Standard Make |
| 49 | Design/Supply/Installation/Testing and Commissioning of Sloped Roof LT feeder panel (3+1) Al. bus bar (CPRI Approved (IS/IEC:61439) of cubical type vermin proper Single door lockable outdoor type fabricated out of 14/16 SWG MS Sheets powder coated weather proof, dust proof with IP 65 protection with 4 legs stand of 2.5 feet height/ground clearance properly grouted in Cement Concrete base b.w.o raising the concrete jacketing (01x01) ft below & Above ground level and 08 inch of dia in 1:3:4 ratio, filter with baby insulators/glands/thimbles suitable for use at 415 Volts 3 Phase,4 wire 50Hz system complete in all respects with following :-Incoming: 100 Amp-3 Phase, 4 pole 25K MCCB-01 No.Outgoing: 200 Amp Suitable Al. Bus bar and 01 No. of 63 Amp 4-Pole TPN |
| 50 | Supply/Installation/Testing & Commissioning of 3-phase 10 KVA,50 Hz Oil cooled unbalanced type Voltage Stabilizer SERVO control of Approved brand COPPER wound of Chinar/AE/Cosco Make ISI/1SO/IEC certified for smooth functioning/constant voltage supply having Technical SpecificationsInput voltage(Ph-Ph) ranging from 90 Volts to 470 Volts and a balanced output Voltage of 420 Volts,±2% Buck Boost Transformer Copper wound 99.9% ,OIL Immersed COOLING OIL, High cut/Low Cut /Time delay/Over Cut through Micro Controller and Spike Protection having 01 No. 63 Amp 3 Pole TP 36kA from input side & 63 AmpTPN from output side Complete job. |
| 51 | Supply and installation of sheet steel Kiosk/ slopped Roof Canopy suitable to house 10 KVA servo stabilizer of following capacities fabricated out of 16SWGM sheel having front door with locking arrangements sand duly powder coated |
| 52 | Supply/Installation/Testing and Commissioning of 3-Phase, Four Pole 100 Amp,415V Ac,50Hz offload Manual Changeover Switch side handle in enclosure Havells/L &T/ABB Make including S/F/Crimping of Suitable Size of thimbles for connections as per site requirement for bypassing 10 KVA AVR. as approved. |
| 53 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat and paint of approved quality all complete. |
| 54 | Laying of cable including excavation of trench 0.3 mtr below ground and back filling the excavated soil in layers and proper compaction shall be done. |
| 55 | Chemical earthing using electrode of size 50mm dia 2 meter long connected with 32x4mm GI internal strip complete with excavation, civil works, RCC cover with back fill compound. The voltage between neutral and earth not to exceed 2 volts. |
| 56 | SITC of Ornamental Street Lights at JKHHC Srinagar |
| 57 | SITC of 2.5 meter height, antique pattern enamel coated with inbuilt control box Ornamental, decorative cast iron pole of approved design/style having connection block (connector) 4 pole 3-5 Amp MCB. |
| 58 | SITC Ornamental decorative cast iron fancy type Double bracket painted with anti-corrosive, enamel painted in antique finish as per approved sample having proper arrangement for fixing of the luminary Victoria type. Bracket having socket for fixing over the pole top of reputed make. |
| 59 | SITC Ornamental, Decorative luminary Victoria type with glass holder and socket painted with anti-corrosive and enamel paint in antique finish to be provided with a LED lamp 22/28 watt (350PC) low of reputed make. |
| 60 | Concrete foundation with 1:2:4 mix mortar having 18” dia hollow portion 4” in/at center, providing/fixing of 4 foundation bolts 16” long with nuts/washers of suitable dia and as per approved quality, block of 2’ height 2’ underground 1’ above ground level with clean/polished finish including cost of form work CGI/MS sheet circular/square pattern and templates 2 no’s for foundation bolts to be fixed at bottom and top for having proper alignment of bolts. |
| 61 | Supply, laying, testing and commissioning of XPLE Al Armored electric power cable 1.1KV grade of reputed make (Approved by Concerned Engineera) 4 core 10mm sq |
| 62 | 4 core 50mm sq. |
| 63 | 4 core 70 mm sq |
| 64 | Supplying and laying of HDPE pipe a)90 mm |
| 65 | SITC of 3 core 1.5mm sq. single core copper wire from fixture to connection box along with necessary lugs etc. complete job. |
| 66 | Supplying and making terminal joints for the following size of 1.1 kv grade PVC insulated aluminium armoured conductor including double brass compression cable glands, terminal lugs, crimping the joints etc complete as requireda) 10sqmm |
| 67 | b) 35sqmm |
| 68 | c) 70sqmm |
| 69 | SITC G.I Pipe 75mm For Road/ Crossing. Providing and laying of G.I Pipe class-B for road crossing 0.50m below ground after excavation and back filling same. |
| 70 | Spiral earthing for poles, using GI wire as earthing lead. |
| 71 | Design fabrication assembling supply installation testing and commissioning of LT sub main panel suitable for 415 V 3 phase 50 HZ 4 wire power supply system panel shall be fabricated out of 2mm thick power coated CPCA sheet steel in cubical formation with aluminium bus bar MCCB 100amp digital volt meters indicators RYBG CT coils complete job as per site requirement. |
| 72 | Rate for chemical earthing using electrode of size 50mm dia 2 meter long connected with 32x4mm GI internal strip complete with excavation, civil works, RCC cover with back fill compound. The voltage between neutral and earth not to exceed 2 volts. |
| 73 | Laying of cable including excavation of trench 0.3 mtr below ground and back filling the excavated soil in layers and proper compaction shall be done. |
| 74 | SITC of Air Condition of Main Showroom 1st Floor Art Emporium |
| 75 | Wiring for circuits for ACs with following size PVC insulated 1100v Grade multi strand copper conductor wire, green insulated multi strand copper conductor for earth wire complete including connections all the three wires for phase, neutral and earth. (without PVC, Conduits)2x6+1x4 Sq mm |
| 76 | Supply and fixing of 2mm thick PVC conduits in following sizes include cost of junction boxes, bends, elbows, sockets, tees etc. laying in slab cutting, chases and making good or surface mounted including all fixing hardware. a). 25 mm dia |
| 77 | 35 mm |
| 78 | Supplying installation testing and commissioning of industrial socket with 32 Amp MCB |
| 79 | Supplying installation testing and commissioning of 2.0-ton AC hot and cold with transformer complete job as required Approved make |
| 80 | Design fabrication assembling supply installation testing and commissioning of LT sub main panel suitable for 415 V 3 phase 50 Hz 4 wire power supply system panel shall be fabricated out of 2mm thick CPCA sheet steel in cubical formation compact mobilize in form 3d construction wall mounted and shall be dust and vermin proof3mmthick cable glad plate shall be provided both at the top and bottom of the panel.MCCB 100AMP 01 No.TPN 63AMP 02 No.DP MCB 40 AMP 04 No.SP. MCB 32 AMP 12 No.Voltmeter Ammeter digitalBus bar 1 setCT coils |
| 81 | Supplying and laying of XLPE insulated Al Armored power cable of approved makea)4 C 70 Sq mm |
| 82 | 4 C 50 Sqmm |
| 83 | Supplying and laying of sub main wiring along with earth wire 4x10+2x 6 Sq mm copper conductor |
| 84 | Supplying installation testing and commissioning of 6-way TPN distribution board |
| 85 | Supplying of laying of DWC pipe 90 mm for smooth entry of cable |
| 86 | Laying of cable including excavation of trench 0.3 mtr below ground and back filling the excavated soil in layers and proper compaction shall be done. |
| 87 | Rate for chemical earthing using electrode of size 50mm dia 2 meter long connected with 32x4mm GI internal strip complete with excavation, civil works, RCC cover with back fill compound. The voltage between neutral and earth not to exceed 2 volts. |
| 88 | SITC of 200 AMP busbar including enclosure/ busbar box complete connection as required Please Enable Macros to View BoQ information |
