|
| 1 | Excavation in trenches n.exc 1.50M wide & n.exc 1.50M deep for foundation etc or for shafts wells cesspits ,manhole pier holes etc n exc 10 sqm on plan and n exc 1.5 m depth and getting in hard/dense soil. |
| 2 | Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and demolished meterial to be removed out side of MD land. |
| 3 | Demolition of brick work/stone boulder masonry built in cement mortar in any position |
| 4 | Material and labour for Cement Concrete (1:4:8) type D2 (40mm graded) in foundation filling and mass concreting. |
| 5 | Material and labour for Brick work with fly ash old size bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6. |
| 6 | Material and labour for Brickwork with fly ash Bricks ,straight or curved in plan to any radius in half brick thick wallin CM (1:6)complete all as specified and as directed |
| 7 | Material and labour for Providing ,cement concrete type B1 (1:2:4) using 20 mm graded aggregate ,in lintel upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses string courses parapets and railing upto 60 cm height copings, kneelers, apex stones, bed plates and similar. |
| 8 | Material and labour for RCC (Nominal mix) type B1 1:2:4 (20mm graded aggregate) for Beams, cantilevers, bressummers, lintels over 1.5 m span |
| 9 | Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces. |
| 10 | Material and labour for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia. or securing with. |
| 11 | - Ditto - as per item No 10 above but 5 mm dia & over upto & incl 10 mm dia in stirrups |
| 12 | Material and labour for Rendering 15 mm thick in CM (1:4) on fair faces of brick/concrete wall surfaces, finished even including mixing integral waterproofing compound. (WPC measured and paid separately) |
| 13 | Supply only integral waterproofing compound |
| 14 | Material and labour for preparation of new plastered wall surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company DepotTinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm complete all as specified and directed at any height incuding necessary scaffolding if required at site. |
| 15 | Material and labour for steel work in tubular sections of any type as in trusses, post, rafter, purlin including special shaped washer etc. Complete using ERW or induction butt welded tubes conforming to IS1161-1979 grade St-240. |
| 16 | Material and labour for preparing new surfaces of steel of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed. |
| 17 | S&F Pre painted GalvaIume aluminium zinc coating GI based corrugated steel sheet0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws etc complete all as specified and directed. |
| 18 | Material and labour for exposed metal frame ceiling with non asbestos fibre cement building boards of 4mm thick of 600mm x 600mm size fixed or laid / inserted to GI framework with appropriate numbers of hangers with screws complete all as specified and as directed. |
| 19 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm for any types of soil. |
| 20 | Removing excavated material (soils) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point. |
| 21 | Material and labour forHard core of broken stone or boulders of gauge n exc 63 mm depossted, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface. |
| 22 | Material and labour for 75 mm thick cement concrete type C-2, 1:3:6 (40 mm graded aggr) as in foor. |
| 23 | Material and labour for Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles including 15 mm thick screed bed 1:6 all as specified and directed. |
| 24 | Material and labour forfor premium quality digital glazed ceramic coloured tiles of approved quality ISI marked (450 X 350X7 mm / 450 x 300 x 7 mm / 600 x 300 x 7 mmthick) as in vertical surfaces such as skirting dados etc set jointed in neat cement slurry and pointed in coloured cement to match with the tiles including 1:4 cement plaster 10 mm thick on brick work and concrete surface complete all as specified and directed by Engineer-in-Charge. |
| 25 | Material and labour for 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like incl 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. |
| 26 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and similar situations. |
| 27 | Material and labour for Providing ,cement concrete type C1(1:3:6) using 20 mm graded aggregate ,in lintel upto 1.5m clear span ,cills,steps, seismic and other similar bands,plinth protection, string courses parapets and railing upto 60 cm height coping and similar. |
| 28 | S&F PVC (SWR) pipes, 110 mm bore,single socketed, in any length,with rubber ring joints, fixed to floor/wall all as specified and directed. |
| 29 | S&F PVC (SWR) bends, 110 mm bore all as specified and directed. |
| 30 | S & F PVC(SWR) Tee110 mm borecomplete all as specified and as directed. |
| 31 | S&F PVC (SWR) vent cowl, 110 mm bore all as specified and directed. |
| 32 | S&F PVC (SWR) pipes, 75 mm bore,single socketed, in any length,with rubber ring joints, fixed to floor/wall all as specified and directed. |
| 33 | S&F PVC (SWR) bends, 75 mm bore all as specified and directed. |
| 34 | S & F PVC(SWR) Tee75 mm borecomplete all as specified and as directed. |
| 35 | Material and labour for PVC (SWR) floor trap with grating,75 mm bore, including jointing to waste pipe with solvent cement including taking down of existing old trap all as specified and directed. |
| 36 | S&F waste pipe of 40 mm dia low density polythelens (LDPE) pipes of pressure rating 6 Kgf/Sq cm |
| 37 | Material and labour for Powder coated anodised aluminium frame of any type for doors, windows, ventilator with one or more rebates including jointing cleats for fixing etc complete all as specified. |
| 38 | Material and labour for powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified. |
| 39 | S&F of aluminium composite panels shall consist of thermoplastic core of any LDPE sandwiched between 2 skins of 0.5 mm thick aluminium sheet making a total panel thickness of 4 mm with outer surface finished with PVDF based coating 30 micron, inner surface finished with a thin coat of polyester paint etc complete all as specified and as directed. |
| 40 | S&F Sheet glass, ordinary quality in square not exc 0.50 Sqm each pane, 4 mm thick fixed to aluminium section complete |
| 41 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified. |
| 42 | S&F door closer hydraulically regulated, designation No 3,aluminium (die cast ) body, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed including taking down old one all as specified and directed. |
| 43 | S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per manufacturer\"s specifications and as directed. |
| 44 | S & F for 30 mm thick factory made solid panel PVC door shutter conferming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C\" channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of \"C\" channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-in-Charge. |
| 45 | S&F for 100mm long mild steel butt hinges, heavy weight cold rolled mild steel and fixed. |
| 46 | S&F 150 mm long aluminium anodised handles, cast type, |
| 47 | S&F for 150 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed. |
| 48 | S&F 300 mm long aluminium alloy, anodised, sliding dooor bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy. |
| 49 | S & F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified. |
| 50 | S & F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified. |
| 51 | S&F 1000 ltr capacity rotational moulded polyethylene water storage tanks with all fittings of GI (cylindrical vertical with closed top) hoisted and fixed in position all as specified. |
| 52 | Supply & fixed 20 mm bore brass ball valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed. |
| 53 | Supply & fixed 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and water tank nipal fixed. |
| 54 | S & F vitreous China squatting pan of Orrissa pattern of approved make of size 580 mm X 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including trap set in and including concrete and connection to flushing pipe incl lime concrete bedding and connection to antisyphonage pipe etc including making good to floor. |
| 55 | S & F vitreous China wash down water closet pan (padestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat (white or black in colour) , closed pattern with flat bottom, and cover and mild steel chromiuum plated or cluminised hinging device also making good to floor. |
| 56 | S & F PVC low level cistern of 10 lit capacity inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved make. |
| 57 | S & Fixed Vitreous chiana wash basin white oval type size 580x450 mm including , waste pipe and plug and porcelain stopper alongwith 32mm dia CP waste coupling and PVC waste pipe in repairs complete all as directed. |
| 58 | S&F 15mm bore pillar taps, fancy type (long body), (Weight not less than 622 gms), cast copper alloy with capstan heads, Decorative type chromium plated screwed down, high pressure screwed for iron pipe complete all as specified. |
| 59 | S & F 15 mm bore chromium plated fancy type bib taps, (Weight not less than 575 gms), cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed. |
| 60 | S & F chromium plated fency type stop cock/angular cock (Weight not less than 575 gms), cast copper allay, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes 15mm bore. |
| 61 | S&F Hand Shower (Health Faucet) (ABS Body) with 8mm Dia, 1.5 Meter Long Spiro chrome flex tube & Wall Hook |
| 62 | S&F 2-way Bib Cock with Wall Flange, Chromium plated, 15mm complete all as specified and as directed |
| 63 | S & F PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality. |
| 64 | S&F soap dish brass chromium plated decorative type approximate size 160x90mm complete all as sfd and directd. |
| 65 | S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed with wall. |
| 66 | S&F decorated type looking mirror of area not exceeding 2.00 sqm each, 6-8 mm thick of any size complete all as specified and as directed by Engineer-in-Charge.Note : Design and pattern shall be approved by GE. |
