|
| 1 | Squirrel Cage Induction motor With Loading Setup (with Starter) |
| 2 | Squirrel Cage Induction motor With Loading Setup (with Out Starter) |
| 3 | Slip Ring Induction motor With Loading Setup (with Starter) |
| 4 | Induction motor With Loading Setup (with Starter) |
| 5 | Wheatstone bridge. |
| 6 | Anderson Bridge |
| 7 | Schering Bridge with Source |
| 8 | 1 Phase Energy meter induction type, |
| 9 | 3 Phase Energy meter Induction type |
| 10 | Earth Megger with necessary connecting leads and rods. |
| 11 | 3 phase Alternator with prime mover. |
| 12 | Synchronizing panel. |
| 13 | PF meter (power factor meter) |
| 14 | LVDT trainer. |
| 15 | 3 phase capacitor |
| 16 | DC Regulated power supply |
| 17 | IC Voltage Power Supply |
| 18 | Signal Generator |
| 19 | DSO |
| 20 | Digital Trainer |
| 21 | DC Voltmeter (Analog) |
| 22 | DC Ammeter (Analog) |
| 23 | Transformer oil Tester Kit, Acidity Test kit |
| 24 | Thermal Overload Relay |
| 25 | AC Contactor |
| 26 | Push Button With NO/NC Elements |
| 27 | Induction Motor |
| 28 | Proximity Switch |
| 29 | PLC |
| 30 | Solenoid Valve |
| 31 | Three Stage Lift Model, Conveyor Model Each |
| 32 | Forward, Reverse and Jogging (Forward and Reverse) Operation Model |
| 33 | 8051 Microcontroller Kit |
| 34 | Digital I/O Interface Board |
| 35 | Seven Segment LED Display Interface Board |
| 36 | 8 Bit DAC Interface Board |
| 37 | Stepper Motor Control Interface Board |
| 38 | DC Motor Control Interface Board |
| 39 | RS 232 Serial Port Cable |
| 40 | LCD Interface Board |
| 41 | Center Lathe (4 ½ ‘Bed length |
| 42 | 4 Jaw Chuck |
| 43 | 3 Jaw Chuck |
| 44 | Chuck key |
| 45 | Box spanner |
| 46 | Cutting Tool H.S.S |
| 47 | Pitch gauge Make |
| 48 | Inside Micrometer Analog |
| 49 | Outside Micrometer Analog |
| 50 | Snap gauge |
| 51 | Gear Tooth Vernier Caliper |
| 52 | Parallel Block |
| 53 | Steel Rule |
| 54 | OutsideCalipers |
| 55 | Thread gauge |
| 56 | Bevel Protractor |
| 57 | Jenny Caliper |
| 58 | Magnetic stand with dial |
| 59 | Marking Gauge (Metal) |
| 60 | Safety Glass |
| 61 | Arc Welding booth welding transformer |
| 62 | Gas welding unit (oxygen and acetylene cylinder) |
| 63 | Flux |
| 64 | Electrode |
| 65 | Face shield |
| 66 | Gas welding goggles |
| 67 | Leather Glows |
| 68 | Flux chipping hammer |
| 69 | Shovel |
| 70 | Rammer set |
| 71 | Slick |
| 72 | Strike-off bar - Wooden |
| 73 | Riddle |
| 74 | Trowl |
| 75 | Lifter |
| 76 | Sprue pin |
| 77 | Brush |
| 78 | Vent rod |
| 79 | Draw spike |
| 80 | Gate cutter |
| 81 | Cope box |
| 82 | Drag box |
| 83 | Core box |
| 84 | Runner |
| 85 | Riser |
| 86 | Molding board |
| 87 | Patterns |
| 88 | Heavy steel wardrobe |
| 89 | ROCKWELL HARDNESS TESTING MACHINE |
| 90 | DEFLECTION TESTING MACHINE |
| 91 | IMPACT TESTING MACHINE |
| 92 | SPRING TENSION TESTER – MANUAL OR HAND OPERATED WITH ANALOGUE DISPLAY |
| 93 | VERIFICATION OF BERNOULLI’S THEOREM |
| 94 | ORIFICE METER APPARATUS |
| 95 | Receiprocating pump Test |
| 96 | VENTURI METER APPARATUS |
| 97 | Universal Milling Machine |
| 98 | Tool and Cutter Grinder |
| 99 | Slotting Machine |
| 100 | BASIC PNEUMATIC TRAINER KIT |
| 101 | BASIC HYDRAULIC TRAINER KIT |
| 102 | PROGRAMMABLE LOGIC CONTROLLER TRAINER |
| 103 | OPEN CUP APPARATUS |
| 104 | CLOSED CUP APPARATUS |
| 105 | REDWOOD VISCOMETER (WITH ENERGY REGULATOR) |
| 106 | SAYBOLT VISCOMETER (WITH ENERGY REGULATOR - FOR EMULSIFIED BITUMEN TEST |
| 107 | FOUR STROKE SINGLE CYLINDER PETROL ENGINE CUT MODEL |
| 108 | FOUR STROKE SINGLE CYLINDER DIESEL ENGINE CUT MODEL |
| 109 | Four Stoke Single Cylinder Diesel Engine Test Rig With Rope Brake Dynamometer |
| 110 | AIR COMPRESSOR TEST RIG |
| 111 | DIGITAL MULTIMETER |
| 112 | Non Contact Tachometer |
| 113 | Anemometer |
| 114 | CNC TURNING CENTRE |
| 115 | CNC MILLING CENTRE |
