|
| 1 | Excavation in foundation in MKR and kankar mixed soil including lift upto 1.5 m and lead upto 30m as directed by engineer incharge. |
| 2 | Laying CC 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | Laying R.C.C. 1:2:4 i/c laying, ramming, curing and including cost of material, labour , T&P With proper completion of work. |
| 4 | Supply and filling in plinth with sand under floors,including watering, ramming, consolidating and dressing complete. |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases for columns. |
| 6 | First class brick work in cement mortar 1:3 (1cement:3Sand) using 1st class building bricks i/c all cost of material, labour T&P etc. as per direction of engineer in charge for proper completion of work. |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 8 | 12.5 mm Thick Cement Plaster IN 1:4 Cement Sand mortar on Brick masonry. |
| 9 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 10 | Providing and fixing (False Ceilling) with Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer- in-charge and as per manufacturer\"s specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60 (including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels. 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm cóc, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge |
| 11 | Providing and fixing 10mm thick plaster of Paris (gypsum anhydrous) upto height of above 5m above for level, over frist class kail wood strips 25x6mm with gap in between and reinforcement with rabbit wire mesh fixed to wooden frame curved surface. |
| 12 | Scrapping old colour or white washing or distemper. |
| 13 | Providing and applying white cement based putty avg. thickness 1mm aproved brand and manufacture over the plaster wall surface even and smooth including cost of material labour and t&p etc complete. |
| 14 | Wall Painting with Acrylic interior grade, having VOC (Volatile Organic Compound) content lase than 50gm /ltr up approved brand and manufacture including applying additional coat wherever required to achieved even side and colour two coat |
| 15 | Finishing of walls with Acrylic smooth exterior emulsion paint in two coats of required shade including priming coat of exterior primer i/c all cost of material, labour and T&P etc. complete. |
| 16 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade to or more coats on new work over and under coat of suitable shades with ordinary paint of approved brand and manufacture |
| 17 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all comers, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. [Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly+A8 screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre) Using R3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m).] |
| 18 | Supply of M.S. grill of approved quality and drawing made of flat iron not bigger than 20x4 mm size including supply of materials, fabrication, labour, T&P and also one coat of red oxide paint complete in all respect as per direction of Engineer-in-charge for proper completion of work at site |
| 19 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fiber matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87-0.89 kg/litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete |
| 20 | Dismantling cement concrete floor, including base concrete and including material within a distance of 60M. Including all taxes but excluding GST. |
| 21 | Dismantling of bricks or stone masonry in lime or cement mortar. Including all taxes but Excluding GST |
| 22 | Dismantling of Existing plaster including Disposal of Refuse Material within 60 m distance. |
| 23 | Dismantling old and defective wooden panels of doors, windows, cup boards and vantilators with chaukhat and including stacking of material with in a distance of 60M as per direction of E/I charge. |
| 24 | Dismantling G.C. sheet including all labour T&P complete |
| 25 | Supply and laying of galvanized corrugated iron roofing 24 B.W.C including cutting and punching with cost of washer, rivet, bolt and nut, labour T&P etc. required for proper completion of work, but excluding cost of trusses flat iron etc |
| 26 | Painting sign boards including lettering & cost of paints. |
| 27 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections /appropriate Z sections {Tubelar Section of 30mm ( thickness 4mm) and sheet 3mm thick}and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 28 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 29 | Providing and injecting chemical emulsion for preconstruction anti termite treatment and creating a chemical barrier under and all round the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor along the external premier of binding expansion joints, surroundings of pipes and conduit etc. complete (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981) Aldine emulsifiable concentrate of any other approved material such as Heptachlor of chlordane will be used. The rate if application of chemical emulsion shall be as follows: - with all taxes but excluding GST. |
| 30 | Providing & fixing Sal wood Chaukhat 100 x 65 single rebate including joint treated with fevicol properly nailed with one coat of primer, black Japan paint on wall side, excluding cost of hold fast complete 100x65mm single rebate (tolerance 3mm) |
| 31 | Providing and fixing (Doors Assessories) including Cost of all materials ISI Mark, labour T&P etc. required for proper completion of work as per direction of E/I charge |
| 32 | P/F SS Door Closer |
| 33 | P/F Doors lock of make Link or equivalent |
| 34 | P/F Stopper in doors |
| 35 | P/F SS Tower Bolt (flush door and wire gauge shutter) |
| 36 | P/F Buffer in doors |
| 37 | P/F Handle |
| 38 | Providing and Fixing Curtain Rods of aluminium with brackets and wooden plugs etc.wherever necessary complete.take 4 1/4\" length. |
| 39 | C.P. Brass towel rail 750x20mm together with pair of C.P. brass brackets to fit the towel rail i/c cost of all fitting Complete. |
| 40 | Providing and laying of Rubble moulded Zig Zag interlocking concrete block pavement having thickness 80 mm as per drawing and technical Specification clause 1504 |
| 41 | Sanitary fitting (ISI) mark including cost of material labour t&p etc with complete work as per direction of Engineer In charge. |
| 42 | P/F Water storage tank capacity of 1000 ltr |
| 43 | P/F 20mm dia CPVC pipe |
| 44 | P/F 25mm dia CPVC pipe |
| 45 | P/F 100mm dia CPVC pipe |
| 46 | P/F T-Socket |
| 47 | P/F Elbow |
| 48 | P/F Socket |
| 49 | P/F W/C Trap |
| 50 | P/F Floor Trap |
| 51 | P/F Wash Basin With Fitting |
| 52 | P/F CP Piller/ Cock Long Nose |
| 53 | P/F CP Bib Cock |
| 54 | P/F CP Stop Cock |
| 55 | P/F Mixer tap in Washbasin and Bathroom |
| 56 | P/F Union |
| 57 | P/F floor mounted, white vitreous china single piece. double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 58 | P/F Towel Rail |
| 59 | P/F PVC Water Tank Ball Cock Valbe |
| 60 | P/F Soap Stand (SS) |
| 61 | P/F Health Faucet (SS) |
| 62 | P/F Toilet Paper Handel (SS) |
| 63 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore |
| 64 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complet |
| 65 | Wiring point for light and fan with 1.5sq. mm P.V.C/V.I.R. insulated single core cable in heavy gauge rigid steel conduit pipe on surface complete with 8SWG G.I. Earch continnuity wire and piano type switch etc. complete in all respect. |
| 66 | Wiring point for Plug with 1.5sq. mm P.V.C/V.I.R. insulated single core cable in heavy gauge rigid steel conduit pipe on surface complete with 8SWG G.I. Earch continnuity wire and piano type switch etc. complete in all respect. |
| 67 | Wiring point for H.P.M. V./H.P.S.V. LAMP WITH 2.5 sq. mm P.V.C./V.I.R. insulated single core cable in heavy guauge rigid steel conduit pipe on surface complete with 8SWG G.I. Earch continuity wire with 15 Amp. Metal clad/S.P.N. switch etc. complete in all respect. |
| 68 | Supplying and fixing of 32A 240V D.P. metal clad rewireable type switch fuse unit on teak wood board complete in all respect. |
| 69 | Supply, instalation ,testing and commissioning od LED Recessed/surface down lighter (Round /Square/ Reactangular) SMD type of Following body Material.12 to 15 watt Please Enable Macros to View BoQ information |
