|
| 1 | (SH: Improvement of Road) |
| 2 | D) Granular Base/Sub-Base with naturally occuring Sand Gravel materialProviding laying and compacting Granular Base/Sub baseaccording to lines, grades and cross sections by using naturally occurred Sand Gravel/confrming to IRC- Grd - II of MOST Specification free from organic or other deleterious constituent spread with motor grader and compacted by rolling with power roller of 8-10 capacity in layers not exceeding 150mm (spread thickness) i/c rolling of the road surface to proper level and grades 30 cm width edging on both sides etc. complete as directed by Engineer-in-charge. |
| 3 | Providing, Laying, Spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel steel/ vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening, binding materials to fill up the interstices of Coarse aggregate, watering and compacting to the required density. |
| 4 | i) Grading - I |
| 5 | i) Grading - II |
| 6 | A) Prime Coat on WMM/WBM(i) P&A primer coat with bitumen emulsion on prepared surface of granular base i/c clearing of road surface and sprayung primer @ 0.7 kg/sqm using mechanical means |
| 7 | P&A tack coat with bitumen emulsion using emulsion pressure distributor @ 0.20 kg/sqm on the prepared bituminous/ granular surface clean with mechanical brooms |
| 8 | Open graded premix surfacing (Providing laying and rolling of open graded premix surfacing of 20 mm thckness composed of 13.2 mm to 5.6 mm aggregates using viscosity grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades)ii) Case -II: Using penetration grade bitumen and hot bitumen mixer 0.5cum. |
| 9 | Seal Coat (providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A seal coats |
| 10 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m, as directed by the Engineer-in- Charge. |
| 11 | (SH :- Construction of Transit Quarter building) |
| 12 | Earthwork in excavationbymechanical means ( Hydraulic Excavator)/ manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All kinds of soil. |
| 13 | Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth consolidating each deposited layer cum by ramming and watering lead upto 50 m and lift upto 1.5 m |
| 14 | Supplying and filling in plinth with sandy soil under floors including, watering ,ramming consolidating and dressing complete. |
| 15 | Providing and laying in position cement concreteof specified grade excluding the cost of centering & shuttering. All works upto plinth level. a)1 : 4 : 8(1 Cement: 4 coarse sand: 8 graded stone aggregate: 40 mm nominal size). |
| 16 | Reinforcement for R.C.C. work i/c.straightening, cutting, bending, binding ,placing in position and bindingall complete in TMT bars. |
| 17 | Providing and laying in position specified grade of reinforced cement concrete workexcluding cost of centering, shuttering and reinforcement- All work up to plinth level: 1:1.5:3 (1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) |
| 18 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 3.2.21:1.5:3 ( 1 cem : 1.5 c/sand : 3 graded stone aggregate 20 mm nom size ) |
| 19 | Reinforced cement concrete work inbeams, suspended floors, roofs having slope up to 15olandings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishingandreinforcement, with 3.3.1in 1:1.5:3 ( 1 cem : 1.5 c/sand : 3 graded stone aggregate 20 mm nominal size ). |
| 20 | FORM WORK |
| 21 | Centering & shuttering including strutting & propping etc.& removal of form for: (a) Foundation, footings, bases of columns etc. for mass concrete. |
| 22 | b) Lintels ,beams,plinth beams ,girders, bressumers and cantilevers |
| 23 | c) Columns ,Pillars,Piers,Abutments, Posts and Struts. |
| 24 | d) Suspended floors, roofs, landings, balconies and access platform |
| 25 | (e) Edges of slab and breaks in floors and walls(i) under 20 cm wide |
| 26 | f) Stairs,(excluding Landings) except spiral staircase |
| 27 | Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand:4 stone aggregate 20 mm & down gauge) finished with a floating coat of neat cement including slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. |
| 28 | BRICK WORK |
| 29 | Brick work with 1st class common burnt clay F.P.S (non modular) bricks in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 30 | Half brick masonary with 1st class common burnt clay F.P.S (non modular) bricks in superstructure above plinth level upto V level in a) Cement mortar 1:4 (1 cement : 4 c/sand) |
| 31 | WOOD WORK |
| 32 | Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately :Local best quality Uningthou wood(a) Local best quality Uningthou |
| 33 | Providing & fixing M.S. grills of required pattern in frames of windows, etc. with MS flats ,square or round bars, etc. including priming coat with approved steel primer all complete. Fixed to window by welding. |
| 34 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for seperately, all complete as per direction of Engineer-in-charge. Float Glass panes 4mm thick. |
| 35 | FINISHING WORK |
| 36 | 12 mm cement plaster of mix 1 : 4 (1 cement : 4 fine sand) |
| 37 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption\"s less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the jointts with white cement and matching pigmentsetc. complete. Size of Tile 600 x 600 mm. |
| 38 | Providing and laying vitrified tiles in different sizes (thickness to be specified by the manufacturer) with water absorption\"s less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, in skirting, riser of steps over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigmentsetc. complete. Size of Tile 600 x 600 mm. |
| 39 | Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 40 | Applying one coat of water thinnable cement primer of approved brandand manufacture on wall surface-Water thinnable cement primer |
| 41 | Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufactures specifications: Two or more coats applied @1.25 ltr/10 sqm over and including one coat of Special primer applied @0.75 ltr/10 sqm. |
| 42 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work. |
| 43 | Painting with oil type wood preservativeof approved brandand manufacture:- New Work (Two or more coats) |
| 44 | Varnishing with varnish of approved brand and manufacture: Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish |
| 45 | 15 mm cement plaster 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement on the roughside of single or half brick wall. |
| 46 | Providing 40 x 5 mm flat iron hold fast 40 cm long i/c fixing to frames with 10 mm dia bolts nuts & wooden plugs & embedding to cement concrete block 30 x 10 x 15 cm 1:3:6 (1 cement:3 coarse sand:6 stone aggregate 20 mm nominal gauge). |
| 47 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with nuts and screws etc. complete. a)250 x 16 mm. |
| 48 | Providing & fixing aluminium handless, ISI marked, anodised (anodic coating not less than grade ac 10 asper IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete. a)125 mm. |
| 49 | SANITARY INSTALLATION |
| 50 | Providing and fixingwater closet squatting pan ( Indian type WC pan)with 100mm SCI Por S trap, 10 litrelow level white PVC flushing cistern, i/c flush pipe, manually,controlled device (handle lever) conforming to IS: 7231,with all fittings and fixures complete, i/ccutting and making good the walls & floors whereever required :(a) White Vitreeous chinaOrrissa Pattern W.C. pan of size 580 x 440mm with integral type foot rests. |
| 51 | Providing and fixing wash basin with C.l. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-16.7A.1. (a) White Vitreous China Wash basin size 550x400 mm with a15 mm CP Brass |
| 52 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :16.9.1. Kitchen sink with drain board 16.9.1.1. 510x1040 mm bowl depth 250 mm |
| 53 | P/F PVC soil waste and vent pipe (external) including cutting hoisting and fitting , makinggood the walls completed. 160 mm |
| 54 | Providing and fixingChlorinated Polyvinyl Chloride (CPVC) pipes , having thermal stability for hot & Cold water supply, including all CPVC plain & brass threaded fittings the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per directon of Engineerin charge. Internal work-Exposed on Wall a) 15 mm diameter |
| 55 | roviding and fixingChlorinated Polyvinyl Chloride (CPVC) pipes , having thermal stability for hot & Cold water supply, including all CPVC plain & brass threaded fittings the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per directon of Engineerin charge. (external work). c) 25 mm diameter |
| 56 | Providing and fixing brass bib cock of approved quality. (a) 15 mmnominal bore |
| 57 | Providing and fixing brass stop cock of approved quality. |
| 58 | Providing and fixingPTMT towelrail complete with brackets fied to wooden cleats with CP brass screws with concealed fittings arrangementof approved qualityand colour600 mm long towel rail with total length of 645mm,width 78 mm and effective height of 88 mm , weighing not less than 190 grams |
| 59 | Providing and fixing 600 x450 mm beveled edge mirror of superior glass( of approved quality ) complete with 6 mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete |
| 60 | Providing and fixing unplasticised PVCconnection pipe with brass unions. 30 cm length. a) 15 mm nominal bore |
| 61 | Providing and Placing on terrace ( at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet ,ouletand overflow pipes but without fittings and the base support for tank |
| 62 | Providing and fixing 1 KW Capacity electric water pump( Tullu) of approved make(Crompton brand ) 0.37/0.50 KW/HP. |
| 63 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 64 | Providing & fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colou or shadewith necessary screws etc. complete. Ii) 250 x 10 mm |
| 65 | Making plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggrt. of 20 mm nominal size) over 75 mm bed of dry bricks ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 66 | Providing & fixing M.S. fan clamp type I of 16 mm dia M.S. bar bent to shape …etc. |
| 67 | Providing and Fixing bright finished bras 100 mm mortice latch and lock with 6 levers and pair of lever handles with necessary screws,etc. complete (best make of approved quality). |
| 68 | Providing and fixing glazing in aluminium dooe, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. With float glass panes of 4.0 mm thickness. |
| 69 | (SH: Construction of Underground water tank) |
| 70 | Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means over areas (exceeding 30cm in depth, 1.50m. in wide as well as 10sqm. on plan) i/c disposal ofexcavated earth lead upto 50mts. and lift upto 1.50m., as directed by the Engineer-in-chargeAll kinds of soil. |
| 71 | Providing and laying in position cement concreteof specified grade excluding the cost of centering & shuttering. All works upto plinth level.a)1 : 4 : 8(1 Cement: 4 coarse sand: 8 graded stone aggregate: 40 mm nominal size). |
| 72 | (d) 1:3:6 ( 1 cement : 3 c/sand : 6 graded stone aggt. 20mm. nominal gauge) |
| 73 | (c) 1:2:4 (1 cement : 2 c/sand : 4 graded stone aggt 20mm nominal size) |
| 74 | Centering and shuttering including strutting, popping etc, and removal of form for:a) Foundations, footings, bases of columns, etc. for mass concrete. |
| 75 | b) Suspended floors, roofs, landings, balconies and access platform. |
| 76 | c) Walls any thickness including attached pilasters, butresses, plinth and string courses etc. |
| 77 | (d) Columns, pillars, posts andstruts |
| 78 | (e) Lintel, beams, plinth beams, girders, bressumers and cantilever, |
| 79 | Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars |
| 80 | Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1 cement : 1.5 : 3c/sand : 4 graded stone aggt. 20mmnominal size). |
| 81 | RCC work in walls ( any thickness) i/c attached cement pilasters, buttresses, plinth and string courses, fillets, columns, pillars,piers, abutments, posts and strutsetc upto floor five level e/c cost of centering, shuttering and reinforcement in (c) 1:1½:3 (1 cement : 1.5 : 3c/sand : 4 graded stone aggt. 20mmnominal size). |
| 82 | RCC work in beams, suspended floors, roofs having slope up to 15º landings, balconies, shelves, chajjas, lintels, bands,plain window sills, staircases and spiral stair cases upto floor five level e/c the cost of centering, shuttering, finishingand reinforcement, with (a) 1:1.5:3(1 cement :1.5c/sand :3 graded stone aggt. 20mmnominal size). |
| 83 | 12mm cement plaster 1:3 (1cement:3 fine sand) finished with a floating coat of neat cement. |
| 84 | Filling available excavated earth (e/c rock) in trenches, plinth sides of foundation etc in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 mts & lift up to 1.50 mts |
| 85 | (SH: Construction of Pucca Drain) |
| 86 | Earthwork in excavationbymechanical means ( Hydraulic Excavator)/ manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All kinds of soil. |
| 87 | Providing and laying in position cement concreteof specified grade excluding the cost of centering & shuttering. All works upto plinth level.a)1 : 4 : 8(1 Cement: 4 coarse sand: 8 graded stone aggregate: 40 mm nominal size). |
| 88 | Providing and laying in position specified grade of reinforced cement concrete workexcluding cost of centering, shuttering and reinforcement- All work up to plinth level: 1:1.5:3 (1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) |
| 89 | Reinforcement for R.C.C. work i/c.straightening, cutting, bending, binding ,placing in position and bindingall complete in TMT bars. |
| 90 | Centering & shuttering including strutting & propping etc.& removal of form for: (a) Foundation, footings, bases of columns etc. for mass concrete. |
