|
| 1 | Taking down existing roof treatment including mud phuska/lime concrete/PCC padding over roof, removing complete layer of bitumen under lime concrete/PCC padding, cement mortar& felt cleaning the surface by hacking to receive plaster and removingdemolished material outside MD land complete all as specified and directed by Engr-in-charge. |
| 2 | Material & labour for applying cement slurry over existing roof surface @ 3 Kg/Sqm complete all as specified and directed by Engr-in-Charge. |
| 3 | Material & labour screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed by Engineer-in-Charge.(Note : Water proofing liquid shall be measured and paid separately) |
| 4 | Material & labour 15mm thick rendering in cement mortar 1:4 tofair faces of brick wall or concrete surfaces finished fair & even without using extra cement mixed with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed by Engineer-in-Charge.Note : liquid water proofing compundshall be measured and paid seperately.complete all as specified and directed by Engineer-in-Charge. |
| 5 | Roof Treatment:-1. All visible cracks to be opened up in V shape and remove all loose particles, cleaned properly with wire brushes and cracks are to be filled with crack filling compound for cracks upto 5 mm width/depth of cracks.2. Cracks of more than 5mm width/depth are to be filled with cement grouting like (URP Cement grout) by injecting through nozzles till refusal by authorized applicators of manufacturer carefully by following manufacturer’s instructions. The size and spacing of the nozzles shall be all as per manufacturers instructions/as directed by Engineer-in-Charge.3. After drying, roof coat paint shall be applied (@ rate of 1 L per 1sqm) with roller in both directions with a gap of 12 hr for each direction over a self prime coat @ 0.5 ltrs of water mixed to 1L of roof coat paint.4. Necessary guarantee of 05 years shall be submitted by the contractor. complete all as specified and directed by Engr-in-Charge. |
| 6 | Supply Integral water proofing liquid complete all as specified and directed by Engr-in-Charge.. |
| 7 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided forcomplete all as specified and directed by Engineer-in-Charge. |
| 8 | Material & labour cement concrete in foundations, fillings and mass concrete 1:2:4 type B-2 using 40 mm graded stone aggregates complete all as specified and directed by Engineer-in-Charge. |
| 9 | Supply & fix 60mm thick PUF panel icluding surface preparation with clean, level and free from any obstruction on which it to be fixed and aligned panels according tothe interlocking system (tongue and groove),ensuring a tight fit and after joining, use appropriate sealants/butyl tape to seal joint and prevant air gaps or thermal bridging alongwith secure the panels to structure using appropriate fasteners (screws, bolts properly) and finaly when PUF panels firmly fixedwith wall/structure, any exposed or gaps can be finished with additinal sealant or trim complete all as specified and directed by Engineer-in-charge. |
| 10 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-Charge. |
| 11 | Supply & fixmicro perforated square edge and attrivate finish mineral fibre (sand micro) of nominal size 595 x 595, & 5 mm thick , having building attribute as in false ceiling , fixed and including grid of size 600 x600 mm having main of aluminium - T of size 35 x 25 x 0.5 mm thick , cross aluminium T of size 25 x 25 x 0.5 mm thick , the grid shall be suitable for mineral fibre tiles and hanging from soffits of existing RCC roof slab with using connecting clips all as per manufactures instruction and complete all as specified and directed by Engineer-in-Charge. |
| 12 | Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed by Engr-in-Charge. |
| 13 | Supply & fix powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed by Engr-in-Charge. |
| 14 | Supply & fix in repair 6 mm thick aluminium composite panels, coloured with decorative choice, fixed to aluminium frame work as in doors/partitions, complete all as specified and directed by Engineer-in-Charge. by Engr-in-Charge. |
| 15 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge. by Engr-in-Charge. |
| 16 | Supply & fix for providing Aluminium powder coated door shutter with powder coated frame 65mmx50mmx1.60mm thick fixed with hing and shutter with to rail, middle rail and bottom rail and style of size 85mmx44mmx2.00mm thick with 200mm size aluminum handle on both sides of shutters, aluminium tower bolt 150mm long 2 Nos per leaf, includingpanel joining cleats, rubber packing, aluminium beading, screws, 01 No Mortice lock 4 levers with two keys for each shutter, 3 Nos butt hinges of stainless steel for each shutter, provision of 8mm dia through bolt with nuts on both side for top and bottom rail etc.complete all as specified and directed by Engr-in-Charge. Note:-All fittings shall be of same finished as of door shutter. |
| 17 | Supply & fix in reapair hydraulic door closer hydraulically regulatedaluminium (die cast) body designation No 3 universal typesuitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 Kg etc in repairs all as specified and directed by Engr-in-Charge. |
| 18 | Supply & fix 5.50mm thick sheet glass ordinary quality exc 0.50 sqm each panes complete all as specified and directed by Engineer-in-Charge.by Engr-in-Charge. |
| 19 | Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.by Engr-in-Charge. |
| 20 | Supply and fixing,18 mm thick HDWPC (High density wooden plastic composite) kitchen cupboard/door shutter board, one side colour/white laminate and other side decorative as in modular kitchen/ cabinets fixed with minifix hardware where ever required including edge band 22 mm wide 0.80 m thick of matching colour on exposed surfaces of board fixed with polymaster adhesive including trimming edges of edge band to true line of thickness of board by manual trimmer, fixed to wall etc complete all as specified and directed by Engr-in-Charge. |
| 21 | Supply and fixing,stainless steel, continuous (piano) hinges, bright finished 40mm width of flaps for cubboard shutters. complete all as specified and directed by Engr-in-Charge. |
| 22 | Supply and fixing, 150mm size aluminium handles, cast type anodised complete all as specified and directedby Engr-in-Charge. |
| 23 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge |
| 24 | Supply and fixing, framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engr-in-Charge.. |
| 25 | Demolition of cement concrete (un-reinforced) in ground floorand paving n exc 15cm thickness (below or above ground level) provided for complete all as specified and directed by Engineer-in-Charge. |
| 26 | Material & labour100 mm thick PCC (1 :4:8) type D2 using 40mmagg as in sub base complete all as specified and directed by Engineer-in-Charge. |
| 27 | Material & labour sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge. |
| 28 | Material & labour Machine Pressed precast concrete interlocking paver block with grey cement and pigment any shapeand size confirming to IS- 15658-2006 of 60 mm thickness M-35 grade complete all as specified and directed by Engineer-in-Charge. |
| 29 | Material & labourPre-cast cement concrete block masonry with solid blocks Type B1 1:2:4 (20 mm graded aggregate, exc. 10 cm in width and setting in mortar, complete all as specified and directed by Engineer-in-Charge. |
| 30 | Supply & fix factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed by Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made |
| 31 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, completed all as specified and directed by Engineer-in-Charge(Note: stainless steel butt hinges and necessary S.S screws shall be paid separately |
| 32 | Supply and fixing, 100 mm size butt hinges, extruded aluminium alloy with galvanished mild steel hinges pin, anodized & fixed, type B-21 completed all as specified and directed by Engineer-in-Charge. |
| 33 | Supply and fixing, brass barrel 150 mm long tower bolts,,with cast or sheetbarrel and rolledor cast bolt and fixed completed all as specified and directed by Engineer-in-Charge. |
| 34 | Supply and fixing, brass, sliding door bolt 300mm long with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed completed all as specified and directed by Engineer-in-Charge. |
| 35 | Supply and fixing, brass handles150mm long , cast type, polished brightand fixing bolt with rolled or drawn brass bolts and fixed completed all as specified and directed by Engineer-in-Charge. |
| 36 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 37 | Material & labour25 mm thick PCC 1:2:4 type B-1, using 25 mm graded stone aggregate as in floors, surfaces finished fair and even complete all as specified and directed by Engineer-in-Charge. |
| 38 | Material & labourforcoloured non skid ceramictiles 7 to 8mm thick (square / rectangular ) area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm in floor (600 mmX 600 mm) etc set and jointed in neat cement slurry and pointed in coloured cement to match with colouredtiles complete all as specified and directed by Engineer-in-Charge. |
| 39 | Material & labourfor coloured non skid ceramictiles 7 to 8mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm on vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match with colouredtiles complete all as specified and directed by Engineer-in-Charge. |
| 40 | Material & labour15mm thick rendering in cement mortar 1:4 on fair faces ofbrickwall or concretesurfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed by Engineer-in-Charge. |
| 41 | Material & labourcoloured Glazed ceramic tiles in verticle surface (350x250mmx7mm /450x350x 7mm thick/450x300x7mm thick), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge. |
| 42 | Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge. |
| 43 | Material & labourfor brick work with fly ash bricks(old size bricks), straight or curved on plan exc. 6 m mean radius, built in CM (1:6). |
| 44 | Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer - in -Charge. |
| 45 | Material & labourrendering 15 mm thick in CM 1:6 on brick masonry surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 46 | Material & labourfor 16 to 18 mm thick Black Granite (of any tpe) work (tablee rubbed and polished) in steps, jambs, pillars, windowcills, Partition and like in cement mortar (1:4) including pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge. |
| 47 | Supply and fixing, in repair kitchen plate rack of size 24 inch x 30 inch x 10 inch with partition for small/large plates fabricated out of Ist quality 24 gauge thick stainless steel sheet complete all as directed by Engineer-in-Charge. |
| 48 | Supply and fixing,in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge. |
| 49 | Supply and fixing, in repair bib taps 15mm bore cast coper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or forunion complete all as specified and directed by Engineer-in-Charge. |
| 50 | Supply & fixin repair grating round 140 mm size of PTMT. (Minimum weight 50gms) complete all as specified and directed by Engineer-in-Charge |
| 51 | Supply and fixing, in repair 15mm bore stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle but fancy type, chromium plated with long shank and cup (conncelaed type) screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge. |
| 52 | Supply and fixing, in repair 15mm bore angle valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge. |
| 53 | Supply and fixing, in repair chromium plated brass tubular towel rail 20 mm dia, 600mm long complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply and fixing, in repair PTMT alloy toilet cabinet with mirror of overall size 350 x 450mm complete all as specified and directed by Engineer-in-Charge.(Cat Part No. 551 of Make Prayag or equivalent model of other makes as approved byEngineer-in-Charge. |
| 55 | Taking up or down15 mm steel tubingand connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge |
| 56 | Supply and fixing,15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge |
| 57 | Dismantling of 100mm bore cast iron drain pipe alongwith fittings and accessoriesjointed in cement mortar and taking out from walls, floors or fromtrenches, if required complete all as specified and directed by Engineer-in-Charge. |
| 58 | Supply and fixing, PVC (SWR) 110 mm borepipes single socketd, in any length with rubber ring joints laid in trenchesor in floors complete all as specified and directed by Engineer-in-Charge. |
| 59 | Material & labourfor preparing newly plastered surfaces and applying applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of 3 mm thick wall care putty over alkali resistant primer complete all as specified and directed by Engineer-in-Charge. |
| 60 | Material & labourfor complete removal of existing treatment on walls, etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of 1mm thick wall care puttycomplete all as specified and directed by Engineer-in-Charge. |
| 61 | Material & labourfor complete removal of existing treatment on walls, etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of exterior emulsion paint in camouflage pattern over a coat of primer complete all as specified and directed by Engineer-in-Charge.. |
| 62 | Material & labourfor preparing old surface of Ceiling plastered or unplastered & applying two coat of white wash with using putty to fill depressions etc complete all as specified & as directed by Engineer-in-Charge. |
| 63 | Material & labourpreparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coatof red oxide zinc chrome primer complete all as specified anddirected by Engineer-in-Charge. |
| 64 | Taking down wall panelling and similar work complete all as specified and directed by Engineer-in-Charge. |
| 65 | Supply and fixing, solid PVC wall lining consisting of 5mm thick Plain colour PVC sheet incluseive of solvent cement and fixing at site on PVC frame complete all as specified and directed by Engineer-in-Charge. |
| 66 | Supply and fixing, 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge. |
| 67 | Taking down carefully existing copper/aluminium point wiring (light/fan/sockets point) complete with all accessories such as switches sockets ceiling rose, wall bracket etc and removing dismantled material and making good disturbed surface of walls/floors etc matching with existing surface etc complete all as specified and directed by Engineer-in-Charge. |
| 68 | Material & labour point wiring for one light point /ceilingfan / bell pointcontrolled by one switch with 1.5 Sqmm PVC insulated, sheathed multi strand copper conductor cable FRLS in and including PVC conduit 20 mm dia,mediumduty, ISI marked including cutting/chasing in wall and fixing of sunken box for one light point, fan point ,bell pointcontrolled by one switch on the same board with other switch or independent including PVC insulated sheathed 1.5 Sqmm multi stranded copper conductor cable FRLS connected to common earth dolly for fixing of switch,sockets etc complete all as specified and directed by Engineer-in-charge. |
| 69 | All as per srl item No.68.00(here-in-before) but for one 3 pin socket out let 5 Amp on same board complete all as specified and directed by Engineer-in-charge. |
| 70 | All as per srl item No.68.00(here-in-before) but for one 3 pin socket out let 5 Amp on independent board complete all as specified and directed by Engineer-in-charge. |
| 71 | AllaspersrlitemNo.68.00(here-in-before) but for 15 Amp socket out let by using 2.5 Sqmm PVC insulated sheathed copper conductor cable FR-LS multi strand on independent boardincluding provn of2.5 Sqmm unsheathed, multi strandedcopper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed by Engineer-in-Charge. |
| 72 | Supply and fixing piano switch flush type piano switch, 6 Amp 240 VoltAC,1 module(ISI Marked) one way etc complete all as specified and directed by Engineer-in-Charge. |
| 73 | Supply and fixing socket outlet 3/5 Pin 6 Amp 230 volts AC flush type 2 in 1 complete all as specified and directed by Engineer-in-charge |
| 74 | Supply and fixing Switch16 Amp, flush type complete all as specified and directed by Engineer-in-charge |
| 75 | Supply and fixingsocket16 Amp, flush type complete all as specified and directed by Engineer-in-charge |
| 76 | Supply and fixingstepped type electronic fan regulator of 100 W flush type on the existing phenolic laminated sheet etc complete all as specified and directed by Engineer-in-Charge. |
| 77 | Supply and fixingceiling rose surface bakelite 65mm x 50mm, 2 to 3 terminalswith back plate etc complete all as specified and directed by Engineer-in-Charge. |
| 78 | Supply and fixingof 20 watt LED tubelight fitting retro fit type 4Xfeet long with replacable rod complete with all accessories and including connecting up withthree core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified and directed by Engineer-in-Charge. |
| 79 | Supply and fixing decorative wall mounting fixture, in double plastic body &designer mesh in gold finish suitable for 9/10 W bulk head fitting , incl taking down unsv fitting complete, complete all as specified and directed by Engineer-in-Charge. |
| 80 | Supply and fixing in replacement of LED ceiling light square recessed mounted LED flat panel complete 600mm x 600mm, 230 volts 35/36 Watt LED light fixing on Surface/ceiling and connecting with 3 corecopper conductor cable etc complete all as specified and directed by Engr-in-charge. |
| 81 | Supply and fixing in replacement of U/S highmast flood light luminaire of HPSV/MH,with LED flood light fitting consist of PDC aluminium houseing in powder coated dia costing power coted in gray finish,high power LED with IP 66protection, fins are provided on housing ,heat resistant tempered glass for protectionwith 5 kv surge protection of 150 W capacity as specified and directed by Engineer-in-Charge. |
| 82 | Supply and fixing LED light fitting, 1X25 watt,5700 Kcomplete with tuff net glass protectionIP:66, fixed to walls incl taking down unsv fitting complete, with GI bracket made out of suitable size of light grade pipe 32 mm dia tubing upto 1.2 mtr length bent to shape with 02 sets of MS clamps made out of 25x3 mm MS flat iron with suitable bolt and nuts and testingetc complete all as specified and directed by Engineer-in-Charge. |
| 83 | Supply and fixing including taking down of sub main wiringwith 2 X 4 sqmm single core cable PVCinsulated unsheathed of copper multi strandard conductorcable , 1100 votls grade drawnin PVC Conduit and insulated 1X 4 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dollycomplete all as specified and directed by Engineer-in-charge. |
| 84 | Material & labour including taking down of sub main wiringwith 4 X 6 sqmm single core cable PVCinsulated unsheathed of copper multi strandard conductorcable , 1100 votls grade drawn in PVC Conduitand insulated 1X 6 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dollycomplete all as specified and directed by Engineer-in-charge. |
| 85 | Supply and fixing including taking down of sub main wiringwith 2 X 6 sqmm single core cable PVCinsulated unsheathed of copper multi strandard conductorcable , 1100 votls grade drawn in PVC Conduitand insulated 1X 6 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dollycomplete all as specified and directed by Engineer-in-charge. |
| 86 | Taking down carefully & Refixing of existing ceiling/exhaust fan in serviciable condition with connecting wire PVC insulated twisted flexible 0.5 sqmm copper condition all complete all as specified and directed by Engineer-in-Charge. |
| 87 | Supply and fixing double doorVTPNdistribution boxsheet metal enclosuremade out of CRCA mild steel sheet concealed surface mounting , 6 way, 415 Volt,fitted with shrouded neutral , insulatedpin type copper bus bar , Dinrail , earthbar ofof 6 way ,complete with MCCB 160 Ampsas incomingcomplete all as specified and directed by Engineer-in-Charge. |
| 88 | Supply and fixing double door sheet metal enclosuremade out of CRCA mild steel sheet concealed surface mounting TPN, 4 way, 440 Volt, with 200 Amprated bus bar suitable for fixing MCBs, isolators etcincluding taking down old complete all as specified and directed by Engineer-in-Charge. |
| 89 | Supply and fixing double door sheet metal enclosuremade out of CRCA mild steel sheet concealed surface mounting SPN, 4 way, 230 Volt, with 200 Amprated bus bar suitable for fixing MCBs, isolators etcincluding taking down old complete all as specified and directed by Engineer-in-Charge. |
| 90 | Supply and fixing double door sheet metal enclosuremade out of CRCA mild steel sheet concealed surface mounting SPN, 8 way, 230 Volt, with 200 Amprated bus bar suitable for fixing MCBs, isolators etcincluding taking down old complete all as specified and directed by Engineer-in-Charge. |
| 91 | Supply and fixing double door sheet metal enclosuremade out of CRCA mild steel sheet concealed surface mounting SPN, 12 way, 230 Volt, with 200 Amprated bus bar suitable for fixing MCBs, isolators etcincluding taking down old complete all as specified and directed by Engineer-in-Charge. |
| 92 | Supply and fixing in replacement of Single pole and neutral sheet metal enclosure with a two pin and earth plug and socket, one single pole 20 Amps, 240V MCB complete all as specified and directed |
| 93 | Supply and fixing MCB TPN 100 Amps C curves MCB repturing capacity 10 KA etc complete all as specified and directed by Engineer-in-Charge. |
| 94 | Supply and fixing MCB TPN 63 Amps C curves MCB repturing capacity 10 KA etc complete all as specified and directed by Engineer-in-Charge. |
| 95 | Supply and fixing MCBSPN 63 ampC curves MCB repturing capacity 10 KA etc complete all as specified and directed by Engineer-in-Charge. |
| 96 | Supply and fixing MCBSPN 40 ampC curves MCB repturing capacity 10 KA etc complete all as specified and directed by Engineer-in-Charge. |
| 97 | Supply and fixing MCB 6 Amp to 32 Amp SPcapacities \"C\" series 10KA rupturing capacaity complete all as specified and directed by Engineer-in-Charge. |
| 98 | Supply and fixing blanking plate for empty space in DB boxes complete all as specified and directed by Engineer-in-Charge |
| 99 | Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth or n exc 10 Sqm on plan and n exc 1.5 m in depth & getting out, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes or for layingunderground cable, pipe lines etc. in soft/ loose soil, complete all as specified & directed by Engineer-in-Charge. |
| 100 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cms thick in soft / loose or hard dence soil complete all as specified and directed by Engineer-in-Charge. |
| 101 | Removing excavated surplus material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge. |
| 102 | Supply & spread unwashed dry river sand for sand cushioning and covering the under ground cable in trenches. (Note :- Punning thickness shall be measured.) |
| 103 | Material & labour for brick protectionwith sub Class`B` bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as directed by Engineer-in-Charge. |
| 104 | Supply laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor,1100 volts grade, ofsize 25 sqmm x 3.5 core complete all as specified and directed by Engineer-in-Charge |
| 105 | Supply laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor,1100 volts grade, ofsize 35 sqmm x 3.5 core complete all as specified and directed by Engineer-in-Charge |
| 106 | Supply laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor,1100 volts grade, ofsize 70 sqmm x 3.5 core complete all as specified and directed by Engineer-in-Charge |
| 107 | Material & labour forreplacement of Test point terminal block made of Gun Metal or Phosphorous bronze size 75 x 75 x 25 mm drilled & screwed incl 3 Nos, 8mm dia, 25mm long Hexagonal head screw complete all as specified and directed by Engineer-in-Charge |
| 108 | Supply and fixing of copper strip 20mm x 3.15 mm with saddels and fixingscrews for roof conductors and down conductors above ground, earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or burried in ground or drawn in conduit/ pipe or fixed to poles or fixed to wall on insulators or any other indicated situation for loop earthing etc as required complete all as specified and directed by Engineer-in-Charge. |
| 109 | Supply and fix in replacement ofaluminium strip 25X3.15 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed by Engineer-in-Charge |
| 110 | Supply and fix air termination , single pointed aluminium rod 12 mm dia and 300 mm long complete all as specified and directed by Engineer-in-Charge |
| 111 | Material& labour for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0 mm buried directly in ground ( earth pit not less than 2.25 m deep below normal ground level), with top edge of the plate vertically to depth of not less than 1.5 m below normal ground level connected to and incl GI strip 25x4 mm and GI pipe 25 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl PCC cover and , watering arrangement with GI pipe 20 mm dia medu=ium grade and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete( Note : PCC chamber shall be constructed at least 1.5m away from earth pit pipe for watering shall be provided in slanting manner.) complete all as specified and as directed by Engineer-in-Charge. |
| 112 | Material& labour for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0 mm buried directly in ground ( earth pit not less than 2.25 m deep below normal ground level), with top edge of the plate vertically to depth of not less than 1.5 m below normal ground level connected to and incl galvanised iron earth wire 4 mm dia by means and GI pipe 25 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl PCC cover and , watering arrangement with GI pipe 20 mm dia medium gradeand MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete( Note : PCC chamber shall be constructed at least 1.5m away from earth pit pipe for watering shall be provided in slanting manner.)complete all as specified and as directed by Engineer-in-Charge. |
