|
| 1 | Notes:-(i) 100 percent nonperishable items of the work shall be deposited by the L1 bidder within 30 days after placing of work order.(ii) The critical path network shall be submitted by L1 bidder immediately after the acceptance of tender and approved by GE.(iii) The bidders must ensure to visit the site, check relevant documents and makes of materials required to be incorporated under the subject from concern Engineer-in-Charge.(iv) The unserviceable material obtained under the schedule of credit shall be handed over to the contractor by the Engineer-in-Charge on a proper gate pass.(v) In case of non-availability of any make mentioned under list of Makes, the L1 Bidder shall obtain non-availability / non-manufacturing certificate from the concern OEM / authorised dealers and submitted to Accepting Officer, in such case the L1 bidder may be incorporated makes as approved by HQ CE SWC Jaipur (Group X)in the works after prior approval of Accepting Officer.(vi) L1 Bidder shall produce E-way bill alongwith test certificate from OEM / manufacturer for costly items / major items of amount above Rs 50,000/- along with RAR’s and Final Bill.(vii) L1 Bidder shall be maintained an album containing Photos of all the material brought at site and each stage wise work progress and kept at site. Same shall be deposited in Engineer-in-Charge office after completion of work.(viii) The cost of all the above provisions shall be deemed to be included in the quoted rate of bidder, nothing extra shall be paid to the bidder. |
| 2 | M&L for Brick work with sub class ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) including demolition of brick work, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-charge. |
| 3 | M&L for 15mm thick rendering in cement mortar (1:6) on fair face surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement including taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge. |
| 4 | M&L for 10mm thick rendering in cement mortar (1:3) on brick or concrete surface of ceiling, finished even & smooth without using extra cement including taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge. |
| 5 | M&L for removing loose ceiling plaster completely, cleaning and dripping mortars and curing of effected surface area, cleaning well expossed reinforcement and applying two coats of anti-corrosive paint to it, supply and fixing mild steel XPM mesh of size 25mm x 25mm (wire dia min. 2mm) to the effected ceiling surface either by welding with exposed reinforcement or by stapling nails or screw or tie with reinforcement, applying cement slury and concrete rich mix1:1.5:3 using 6mm graded aggregate and making the surface level and curing 6-7 days and then making well finish the surface using cement mortar 1:3 complete all as specified and directed by Engineer-in-charge. |
| 6 | S&F as in repair steel framed work such as grills, gratings, etc., with ends of bars shouldered and or forged into spikes, framed guard bars, ladders, framed balusters, walk ways, railings, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc. including two coat of synthetic enamel weather proof paint over a coat of red oxide primer complete all as specified and as directed. |
| 7 | M&L for glazed ceramic tiles (coloured) 300mm x 600mm x 7-8mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment including dismantling existing tiling with cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-charge.Make :- Johnson/Kajaria/Somany or equivalent technocommercial make as specified in Appendix \"A\". |
| 8 | M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) including dismantling existing tiling with cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-charge. Make :- Johnson/Kajaria/Somany or equivalent technocommercial make as specified in Appendix \"A\". |
| 9 | M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in verticle surfaces, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) including dismantling existing tiling with cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-charge.Make :- Johnson/Kajaria/Somany or equivalent technocommercial make as specified in Appendix \"A\". |
| 10 | M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, filling cracks with wall care putty etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge. |
| 11 | M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applyingtwo coat of white wash complete all as specified & directed by Engineer-in-Charge. |
| 12 | M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-charge. |
| 13 | M&L for preparation of new plastered and unplastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of appropirate primer over and including 2mm thick layer of ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting complete all as specified & directed by Engineer-in-Charge.Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or Techno commercial as mentioned in Appx \"A\". |
| 14 | Taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats and S&F pressed steel frames for door of size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc made out of mild steel sheet of 1.25mm thickness complete all as specified and as directed. |
| 15 | Taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats and S&F pressed steel frames for door of size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc made out of mild steel sheet of 1.25mm thickness complete all as specified and as directed. |
| 16 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) including dismantling existing wooden / iron / stone chowkhats and making good existing surface with CM (1:3) complete all as specified and directed by Engineer-in-charge.Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Make : Aldeco, Giza, Alstone or Techno commercial as mentioned in Appx \"A\". |
| 17 | S&F new 30 mm thick factory made flush shutters, solid core construction, withblock board core and plywood face panels, commercial type on both side incl both side 1.00 mm thick one side Decorative laminate and other side plain laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer\"s instructions® completecomplete all as specified and directed by Engineer-in-charge including supply and fixing of following items :-(a)Stainless steel (304 Grade) finished butt Hinges 100 mm, 4 Nos per leaf(b)Stainless steel (304 Grade) finished square tower bold 200 mm long-2 Nos per leaf as per table 01 dia of bolt 12 mm(c) Stainless steel (304 Grade) Finished Handles 200 mm-2 Nos per leaf.(d)Stainless steel (304 Grade) finished sliding bold 300 mm-1 No per leaf, 16 mm dia(e)Stainless steel (304 Grade) Finished Floor door stopper-1 140mm Nos per leaf.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 18 | S&F new 35mm thick factory made glazed and skeleton shutters made of second class hard wood (Bonsum/Hollock), open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Part I Section 8 Clause 8.24 (a) kiln seasoned and chemically pressure treated fixed to chowkat incl Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in CM 1:4 (01 No in each shutter), stra, complete all as specified and directed by Engineer-in-charge including supply and fixing of following items :-(a)Stainless steel (304 Grade) finished butt Hinges 100 mm, 4 Nos per leaf(b)Stainless steel (304 Grade) finished square tower bold 200 mm long-2 Nos per leaf as per table 01 dia of bolt 12 mm(c) Stainless steel (304 Grade) Finished Handles 200 mm-2 Nos per leaf.(d)Stainless steel (304 Grade) finished sliding bold 300 mm-1 No per leaf, 16 mm dia(e)Stainless steel (304 Grade) Finished Floor door stopper-1 140mm Nos per leaf.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 19 | S& F for 30 mm thick Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter ofcomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(a)Stainless steel (304 Grade) finished butt Hinges 100 mm, 4 Nos per leaf(b)Stainless steel (304 Grade) finished square tower bold 200 mm long-2 Nos per leaf as per table 01 dia of bolt 12 mm(c) Stainless steel (304 Grade) Finished Handles 200 mm-2 Nos per leaf.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 20 | S&F anodised aluminium frames powder coated (thickness of powder coating shall not less than 50 micron) for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc including taking down exisitng steel window/ventilator complete all as specified and directed by Engineer-in-Charge. Make :- FENESTA/NALCO/AISor equivalent technocommercial make as specified in Appendix \"A\". |
| 21 | S&F anodised aluminium window / ventilators shutters powder coated (thickness of powder coating shall not less than 50 micron) side hung type, without sash bars having aluminium sections weighting 0.55 Kg/RM including necessary jointing cleats, glazing clips, anodised aluminium snap beading, screws, rubber neoprene packing including anodised aluminium fitting such as peg stay 150mm long (1 No), hinges type B21 100mm size (2 Nos), suitable handle (1No) complete all as specified and directed by Engineer-in-Charge. Make :- FENESTA/NALCO/AISor equivalent technocommercial make as specified in Appendix \"A\". |
| 22 | S&F as in repairs stainless steel drapery rod of 25 mm inner dia (in lengths as directed) with & including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, all as specified & as directed. |
| 23 | Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain / brass CPVC SDR 11 fittings including all fittings and fixed complete to walls and ceilings or laid in floors, trenches including taking down old unsv tubing complete all as specified and directed by Engineer-in-charge. Make : Finolex/Supreme/Princeor equivalent technocommercial make as specified in Appendix \"A\". |
| 24 | Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain / brass CPVC SDR 11 fittings including all fittings and fixed complete to walls and ceilings or laid in floors, trenches including taking down old unsv tubing complete all as specified and directed by Engineer-in-charge. Make : Finolex/Supreme/Princeor equivalent technocommercial make as specified in Appendix \"A\". |
| 25 | S&F CPVC brass male brass threaded adaptor special fitting (MTA/MBTA) for connecting of CPVC tubing outer dia 16/20mm complete all as specified and directed by Engineer-in-c/harge. |
| 26 | S&F 20mm outer dia CPVC brass elbow fittings complete all as specified and directed by Engineer-in-charge. |
| 27 | S&F in repair Vitreous china premium/ 1st quality wash down water closet wall hung EWC (Extended wall mounted water closet) white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. with & including WC seat cover closed pattern with flat bottom and cover, health faucet ABS CP, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified & as directed by Engineer-in-charge.Make :- Parryware cat part No Verve AM C022N & C0762 / Hindware Cat part No 20096 (P-15) /Jaquar or equivalent in Makes mentioned in Appendix \"A\" here-in-after. |
| 28 | S&F as in repair 15 mm bore bib tap, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.Make : Jaquar/Hindware/Parrywareor equivalent technocommercial make as specified in Appendix \"A\". |
| 29 | S&F as in repair 15mm bore brass chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union with shower arm 15mm size, 195mm long iwht bend of 45 degree with flange complete all as specified and directed by Engineer-in-charge.Make : Jaquar/Hindware/Parrywareor equivalent technocommercial make as specified in Appendix \"A\". |
| 30 | S&F as in repair 15mm dia stop cock cast copper alloy, angular type with, chromium plated long shank and cup with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.Make : Jaquar/Hindware/Parrywareor equivalent technocommercial make as specified in Appendix \"A\". |
| 31 | S&F as in repair 20mm dia CPVC ball valve or gate valve both endsfor cpvc pipe and fixed to complete all as specified and as directed. |
| 32 | Supply & fixing in repair 110mm bore uPVC pipes grade ‘B’ single socketed in any length with rubber ring joints, fixed along walls with incl all the necessary fitting like bends/trap/tee and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. Make of Pipe: FINOLEX/PRICE/SUPREME or equivalent in makes mentioned in Appendix \"A\" here-in-after.Note:-Bracket, clamp, nut bolt, fastener, slotted channel etc. shall be made of deep drawn low carbon steelmaterial with hot dip zinc aluminium flake coated and fixed all as shown on BTD-916 drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account.Note:(i) the testing for leakage of pipe shall be done before connecting the pipes(ii) All pipes shall be minimum 4\" away from walls fixed with GI bracket(iii)The gully trap shall be minimum 90 cm away from wall.(iv)Separate pipes for each floor should be provided.(v) Sewage and drain system shall be seperate.Make of clamp:ISI Marked as approved by GE. |
| 33 | Supply & fixing in repair 75mm bore uPVC pipes grade ‘B’ single socketed in any length with rubber ring joints, fixed along walls with incl all the necessary fitting like bends/trap/tee and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. Make of Pipe: FINOLEX/PRICE/SUPREME or equivalent in makes mentioned in Appendix \"A\" here-in-afterNote:-Bracket, clamp, nut bolt, fastener, slotted channel etc. shall be made of deep drawn low carbon steelmaterial with hot dip zinc aluminium flake coated and fixed all as shown on BTD-916 drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account.Note:(i) the testing for leakage of pipe shall be done before connecting the pipes(ii) All pipes shall be minimum 4\" away from walls fixed with GI bracket(iii)The gully trap shall be minimum 90 cm away from wall.(iv)Separate pipes for each floor should be provided.(v) Sewage and drain system shall be seperate.Make of clamp:ISI Marked as approved by GE. |
| 34 | Disconnecting existing tanks of capacity 1000 Litre, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position afterCleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc.including repair small fittings of CPVC/GI medium grade such as socket/elbow/nipple of diffrent sizes, TEE/union/Reducer for 15mm bore pipe (if required) complete all as specified and as directed |
| 35 | Disconnecting existing tanks of capacity 500 Litre, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position afterCleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc.including repair small fittings of CPVC/GI medium grade such as socket/elbow/nipple of diffrent sizes, TEE/union/Reducer for 15mm bore pipe (if required) complete all as specified and as directed |
| 36 | S&F as in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe 20mm dia and fixed (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and as directed. |
| 37 | S&F as in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe 25mm dia and fixed (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and as directed. |
