|
| 1 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kinds of soil.a. Pipes, cables etc. exceeding 80 mm dia. butnot exceeding 300 mm dia |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level.A. 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :a. 250x10 mm. |
| 4 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.a. Hot finished welded type tubes |
| 5 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 6 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles wll be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish/double charge of make \"Somany Duragress\" strio valor rovere wood teak matte or any equivalent make of size 196mm x 1200 mm complete in all respect as per direction of Engineer in Charge |
| 7 | Providing and fixing Glass mossaic tiles on finished plain wall surface of size 48 mm x 48 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in- Charge: |
| 8 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :a. Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 9 | Providing & fixing UV stabilised fiberglass einforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts&of nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufacturedout2400 TEX panel rovigs incorporating minimum 0.3% ultra-violetstabiliser in resin system under approximately 2400 psi and hot cured.They shall be of uniform pigmentation and thickness without air pocketsand shall conform to IS 10192 and IS 12866.The sheets shall be opaqueor translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat |
| 10 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main“T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. a. 8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing. |
| 11 | CEMENT PLASTER (IN COARSE SAND) .12 mm cement plaster of mix : 1:4 (1 cement : 4 coarse sand) |
| 12 | Extra for providing and mixing water proofing material in cement per bag of plaster work in proportion recommended by the manufacturers. |
| 13 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats |
| 14 | Removing existing synthetic coating by scraping, sand papering, by any machine as required as per site condition, and preparing the surface smooth and ready for adhering new synthetic layer, all complete as per direction of Engineer-in-Charge.\" |
| 15 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.A.For thickness of tiles 10 mm to 25 mm |
| 16 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 17 | Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. |
| 18 | Dismantling of flexible pavement (bituminous courses) by mechanical means and disposal of dismantled material up to a lead of 1 kilometer, as per direction of Engineer-in-charge. |
| 19 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 20 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster |
| 21 | Demolishing cement concrete manually/ by mechanical meansncluding disposal of material within 50 metres lead as per direction of Engineer -in - charge.Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 22 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate |
| 23 | Providing and placing in position 100 mm thick factory made machinebatched & machine mixed Precast RCC Rectangular Covers ondrains of footpath of various sizes, of M-25 grade cement concretefor RCC work, including cost of centering, shuttering, reinforcementof 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c onboth ways , neat cement punning on finished surface, properlyencased on all edges with 1.6 mm thick , 100 mm wide MS sheetduly painted over priming coat , reinforcement to be welded at edgeswith MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/ccost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge. |
| 24 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C.flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :a.W.C. pan with ISI marked white solid plastic seat and lid . |
| 25 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required.a. One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 26 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:a. (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 27 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 28 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipea. 32 mm dia |
| 29 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 a.15 mm nominal bore |
| 30 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.A.15 mm nominal bore |
| 31 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm lengtha. 15 mm nominal bore |
| 32 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :a. 150 mm diameter |
| 33 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work:65 mm dia nominal bore |
| 34 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :65 mm diameter pipe |
| 35 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall.a. 20 mm nominal dia Pipes |
| 36 | Providing and filling sand of grading zone V or coarser grade, all round the G.I. pipes in external work :65 mm diameter pipe |
| 37 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) a. 65 mm nominal bore |
| 38 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarsesand : 10 graded stone aggregate 40 mm nominal size) up tohaunches of S.W. pipes including bed concrete as per standarddesign :a. 150 mm diameter S.W. pipe |
| 39 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete a.150 mm dia. R.C.C. pipe |
| 40 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion a. Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 41 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)a. Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 42 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):a.With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 43 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.a.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side |
| 44 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain white color board for backing of cup boards and bathroom/kitchen cabinets etc. of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel screws etc. all as per direction of Engineer-In- Charge. (Note: stainless steel screws shall be paid separately).12 mm thick |
| 45 | Providing and laying synthetic cushioned acrylic surfacing system of international level (outdoor) duly approved by ITF of classification - Il with minimum five years warranty with the following nine layers of synthetic cushioned surfacing material including marking of court lines with 100% acrylic resin based line marking painti) Filler course (one layer of acrylic resurface)il) Heavy rubber course (three layer of flexible latex based liquid rubber with coarse particlesiii) Fine rubber course (two layers of flexible latex based liquid rubber with finer particles)iv) texture course (one layer of flexible filler acrylic base)v) Finish Course (two layers of 100% acrylic resin base paint).All above applications are to be applied as per manufacture\"s specification/ consumption standard and as per the direction of Engineer-in-charge. (Rate: The rate includes the cost of material , all statutory taxes , import duty, insurance , labour tools plants and equipment testing of material , transportation of material from manufacturer to the site ,storing and laying of the same. Nothing extra shall be paid over the quoted rates. |
| 46 | Providing and fixing Basketball Pole made of 8\" dia pipe with 2.2 meter projection and basketball board transparent acrylic imported 20mm thick size 180cm x 105cm with dunking ring, net and frame. Ring is bolted through the backboard into the main frame construction forextra strength and durability Use of branded MRF Epoxy paint.(B.B.8.2.2.20) or equivalent as per direction of Engineer-in-charge. |
| 47 | Providing and fixing of GRC jali 50mm thick of required size, pattern, design and colour. The jali shall be made from 53 grade white portland cement, Quartz fine Silica sand, Alkali resistant Glass fibre, Super plasticizer and UV resistant synthetic inorganic pigments. The material casting should take place in synthetic rubber/FRP mould. The rate shall include erection of all fasteners, flashing and capping for all edges, cost of all labour, equipment\"s, material and taxes etc all complete as per direction of Engineer In Charge. |
| 48 | Providing & fixing speed beaker in ABS body HD type black yellow colour of size 350x250x50 mm along with necessary fitting and fixture complete as per direction of Engineer-in-charge |
| 49 | Less GST correction factor @ 0.027 on DSR items except item no. 44 to 47 |
| 50 | Add 3% Cost Index on DSR items except item no. 44 to 47 |
