Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off premises ,complete all as specified and directed |
| 2 | M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 ,complete all as specified and directed |
| 3 | M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 ,complete all as specified and directed |
| 4 | M&Lfor glazed ceramic coloured tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 ,complete all as specified and directed.Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment . |
| 5 | M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 6 | Demolition of cement concrete un reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed. |
| 7 | M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring average 25 mm thick surface finished even andrough (as in levelling course) to receive the topping layer complete all as specified and directed. |
| 8 | M & L for Vitrified Ceramictiles light shade polished (square / rectangular) of 10mm thick, area of each tilenot exc. 0.36sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed. |
| 9 | M & L for Vitrified Ceramictiles light shade polished (square / rectangular) of 7 to 8mm thick, area of each tile exceeding 0.42 sqm but not exc. 1.00sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed. |
| 10 | Demolition of brickwork built in cement or cement lime mortar including all quoins, arches pillar etc complete all as specified and directed. |
| 11 | M&L Brick work with flyash bricks, straightor curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 12 | Taking down cement or cement lime plaster, of any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 13 | M&L for Rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) complete all as specified and directed. |
| 14 | M&L for rendering 5 mm thick in CM 1:3 on RCC ceiling surface and finished even and smooth with out using extra cement complete all as specified and directed . |
| 15 | Taking down chowkhat or frames n exc 1.50 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed |
| 16 | Taking down chowkhat or frames exc 1.50 Sqm and n exc 4 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed |
| 17 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories ,complete all as specified and directed . (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories.) (Area not exceeding 2.00 sqm) |
| 18 | Providing and fixing factory made uPVC white colour fixed or lovoured window/ ventilator made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profileOnevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick,galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass ,complete all as specified and directed (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories) (Area not exceeding 1 sqm each) |
| 19 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm longfasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing withselected quality glass ,complete all as specified and directed. (Note: The unit rate quoted by contractor includes cost of glass and panel and includes all other connected accessories) |
| 20 | S & FPowder coated three track Aluminium sliding window with frame not less than 1.8 mm thick excluding aluminium grill and including 4 mm thick tinted glass, beading & necessary rubber packing, locking & opening arrangement, all fitting and fixture complete all as specified and directed. |
| 21 | S&F 7mm thick aluminium grills of make \"Decogrill\" model DG 104 surrounded by aluminium \"C\" channel with mesh size 75 X 75mm all as specified and directed. |
| 22 | S&FStainless steel wire cloth. 0.36mm nominal dia of wire and averagewidthof aperture1.40mm and fixed with stainless steel wire staplescomplete all as specified and directed. |
| 23 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet re-inforced with MS square tube in opening as per specification and shown on drg SSR Part-II 2010. |
| 24 | S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rails lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement , as per specification and shown on drawing in SSR Part-II (2010) ,complete all as specified and directed |
| 25 | S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 26 | S&F Flush shutters 35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sidescomplete all as specified and directed. |
| 27 | M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 28 | Taking down shutter of any description area exceeding 1 sqm but n exc 2 sqm each and removing to store complete all as specified and directed. |
| 29 | Taking down shutter of any description not exceeding 1 sqm each leaf and refixing, in same opening after easing and adjusting building hard ware etc complete all as specified and directed |
| 30 | Taking down shutter of any description exceeding 1 sqmbut not exiding 2 Sqmeach leaf and refixing, in same opening after easing and adjusting building hard ware etc complete all as specified and directed |
| 31 | M&L Second class hard woodplain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 32 | S&F mild steel flat iron as in bands straps, supports or stays for rainwater, ventilating pipes including bolt if required, hooks (stay) heavy for large gates,hook and pintle hinges,large hasps and staples, brackets for WHB, hold fasts, wall ties, hooks for hanging fans ,cleats for securing purlins to wood trusses or rafters and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed. |
| 33 | M&L for Cutting holes in brick walls exc half brick but not exc one brick built in cement mortor or cement lime mortor and stone walls built in lime mortor for inserting hold fasts and makinggood dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as requiredcomplete all as specified and directed. |
| 34 | S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed. |
| 35 | S&F 100 mm long aluminium handles cast type, anodized complete all as specified and directed |
| 36 | S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed |
| 37 | S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed |
| 38 | S&F in repair 100 mm long aluminium anodized handles fabricated typecomplete all as specified and directed |
| 39 | S&F in repair 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed. |
| 40 | S&F in repair 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed |
| 41 | S&F in repair 75 mmButt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed |
| 42 | S&Fin repair 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed |
| 43 | S&F in repairs 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 44 | Hacking out old broken glass (any thickness, size quality or description) form wooden frames or stone, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed. |
| 45 | S&F 3 mm thick sheet glass ordinary quality and gazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed. |
| 46 | S&F 3 mm thick figured glass pin headed type and gazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed. |
| 47 | S&F in repairs aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed. |
| 48 | S&F in repairs 18/19 mm thick high density PVC/ WPC solid fibre board with prelaminated PVC sheet as Kitchen cupboard and frame including taking down the old cupboard shutters and removing to store complete all as specified and directed. |
| 49 | S&F continuous (piano) hinges of width of flaps (when open) 30 mm, mild steel, bright finish or electrogalvanised complete all as specified and directed |
| 50 | S & F magnetic catcher catcher with nut and screw of mild steel bright finish all as specified and directed |
| 51 | S & F40 mm dia cupboard knobs fixed with nuts screw and washer of mild steel bright finish complete all as specified and directed. |
| 52 | S & Fin repair40 mm dia cupboard knobs fixed with nuts screw and washer of mild steel bright finish complete all as specified and directed. |
| 53 | S & F in repair hasp and stapple safety type aluminium anodised 75 mm long with mild steel hinge pin including bolt to hinge plate fixed with screw complete all as specified and directed. |
| 54 | S&F in repairs 15 mm dia Curtain rods, mild steel, chromium plated with fixing brackets complete all as specified and directed. |
| 55 | S&F in repair SS Curtain rodBracket fancy type for curtain rod 25 mm dia of any colour as approved complete all as specified and directed. |
| 56 | S&F in repairfloor door stopper of aluminium alloy body and tongue, anodised, over all length of cover plate 140 mm with hard drawn steel spring fixed in door etc complete all as specified and directed. |
| 57 | S & F in repair bevelled edge Looking mirror of any size without frame of selected quality glassmounted on wall with chromium plated stainlessscrews complete all as specified and directed |
| 58 | S&F in repairsingle door PVC cabinet mirror of size 300 mm x 450 mm with internal shelves all as specified and directed |
| 59 | S & F in repair sheetGlass Shelf assembly consisting of 5.5 mm glass sheet shelf 12 cm wide with cromium plated bracket guard and railing 60 cm long complete all as specified and directed.. |
| 60 | Taking up or down steel tubing and connections including cleaning if refixingrequired for 15 mm bore of pipe complete all as specified and directed. |
| 61 | Taking up or down steel tubing and connections including cleaning if refixingrequired for 20 mm bore of pipe complete all as specified and directed. |
| 62 | S&F GI tubes medium grade (ISI marked)with all fittingsfixed complete to walls, ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed. |
| 63 | S&F GI tubes medium grade (ISI marked)with all fittings fixed complete to walls, ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed. |
| 64 | Supplying and laying as in repair of CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified or laid in floors concealed or open of any length including taking down or up existing GI tubing & connections all as specified and directed by Engr-in-charge. |
| 65 | Supplying and laying as in repair of CPVC pipes 32mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified or laid in floors concealed or open of any length including taking down or up existing GI tubing & connections all as specified and directed. |
| 66 | Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 15 mm bore of pipe complete all as specified and directed. |
| 67 | Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 20 mm bore of pipe complete all as specified and directed. |
| 68 | S&F in repairChromoium plated Bib cock with flanges Quarter turn 15 mm bore complete all as specified and directed. Make-Jaquar , Cera & equivalent as approved by GE andEngineer in Charge. |
| 69 | Taking down bib tap /wash basin tap/pillar tap/stop cock/mixture tap and refixing the same after repair and replacement of washer only for 15 mm bore size without replacing spindles complete all as specified and directed. |
| 70 | Taking down bib tap /wash basin tap/pillar tap/stop cock/mixture tap and refixing the same after repair and replacement ofspindles for 15 mm bore size ,complete all as specified and directed. |
| 71 | S & F in repair Brass chromium plated wall mixer non-telephonic shower arrangement with connecting legs & wall flanges for 15 mm bore of pipe all as specified and directed. |
| 72 | S & F in repair Brass chromium platedhole bidet mixer (Basin mixer) with pop-up waste system with 300 mm long braided hoses complete all as specified and directed. |
| 73 | S & F in repair Brass chromium plated Sink mixer with raised J shaped swinging spout (Wall mounted model) with connecting legs & Wall flangescomplete all as specified and directed. |
| 74 | S&F in repairChromoium plated angular stop cock for 15 mm bore complete all as specified and directed. |
| 75 | S&F in repairChromoium platedTwo-way angular stop cock for 15 mm bore complete all as specified and directed. |
| 76 | S&F in repair, 15 mm bore stop cock, cast copper alloy with long shank and cup (concealed type) fancy type chromium plated screwed down high pressure with crutch & butterfly handle screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 77 | S&F in repair 15 mm bore stop cock, cast copper alloy screwed down high pressure with crutch & butterfly handle fancy type chromium plated screwed both ends for iron pipe and fixed complete all as specified and directed |
| 78 | S&F in repair pillar tap cast copper alloy with capstan head chromium plated crewed down high pressure with or without lettered hot or cold with long screwed sharks and ply nuts 15 mm dia complete all as specified and directed |
| 79 | S & F in repair bottle trap chromium plated for WHB as per approved quality all as per specified and directed. |
| 80 | S&F in repairPVC waste pipe for WHB etc all as specified and directed. |
| 81 | S&F in repairs 32 mm bore dia waste coupling of(min weight 32 mm-45 gm of PTMT) (half or full threaded) etc complete all as specified and directed |
| 82 | S&F in repair CP grating 100 mm dia with waste hole (minimum weight 40 gm) complete all as specified and directed |
| 83 | S & F in repair CP Jet spray for 15 mm bore all as specified and directed. |
| 84 | S & F in repairs Hand shower (Health faucet) with 1 mtr long Easy flex tube in crome finish & wall hook ,complete all as specified and directed. |
| 85 | M&L in repairs for vitreous china wash basin, white,flat back, size 550 x 400 mmincluding supply & fixing of brass chromium plated coupling 32 mm etc complete all as specified and directed. |
| 86 | M&L in repair Wash down water closet vitreous china white pedestal pattern with \"P\" or \"S\" trap including connecting to outgoing drain pipe & to flushing pipe excluding flushing cistern and flush pipe complete all as specified and directed. |
| 87 | S&F in repairs plastic water closet seat cover, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 88 | M&L in repairs vitreous china squatting pan , ‘Orissa’ Pattern, size 580 X 440 mm white, with integral foot rests etc. complete all as specified and directed. |
| 89 | S & F in repair Kitchen sink made of stainless steel 1 mm thick with plug washer and waste pipe incl bedding fixing cantilever brackets and connetction union to pipe overall size 915 X 460mm bowl size 405X 355 mm complete all as specified and directed |
| 90 | S& F in repair 1 mm thick stainless steel plate rack of size 900X600X200 incl fixing with rawal plug and screws complete all as specified and directed. |
| 91 | S & Frotational moulded polyethylenewater storage tank (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position including dismantling of old u/s water tankand removing to storecomplete all as specified and directed |
| 92 | S & Frotational moulded polyethylenewater storage tank (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in position including dismantling of old u/s water tank and removing to store complete all as specified and directed |
| 93 | S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed. |
| 94 | S&F ball valves for 25 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 455 gms) complete all as specified and directed. |
| 95 | S&F in repairs ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed. |
| 96 | S&F in repairs ball valves for 25 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 455 gms) complete all as specified and directed. |
| 97 | S & F in repair PVC Tank cover for 500 Ltr capacity fixed in position with nuts and bolt complete all as specified and directed |
| 98 | S & F in repair PVC Tank cover for 1000 Ltr capacity fixed in position with nuts and bolt complete all as specified and directed |
| 99 | S&F in repairs, PVC valveless symphonic action type low levelflushing cistern, 10 ltrs capacity with inlet, ball valve, float and handle including bracket complete all as specified and directed |
| 100 | S & F in repair internal fitting for low level flushing cistern (Syphon) complete all as specified and directed. |
| 101 | S&F in repairs flush pipe 32 mm dia of polyethylene of low or high density or PVC, for low level cisterncomplete all as specified and directed. |
| 102 | S & F in repair 125 mm dia chromium plated shower rose ofwith or without swivel joint incl fixing to steel pipe complete all as specified and directed. |
| 103 | S&F in repair PVC connection 15 mm bore, 450 mm long complete with both ends unions complete all as specified and directed. |
| 104 | S&F in repairs CP anodised tubular tower rail, 20 mm dia, D type, 60 cm long between flanges etc. |
| 105 | S & F in repair 75 mm PVC(SWR) floor trap with grating incl jointing with solvent cement complete all as specified and directed |
| 106 | S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe of 20 mmbore dia of pipe complete all as specified and directed. |
| 107 | S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends (ISI marked) for iron pipe of 25 mmbore dia of pipe complete all as specified and directed. |
| 108 | S & F in repair Soap dish any type fixed to plug with chromoium plated brass screw complete all as specified and directed. |
| 109 | S & F in repair corner glass shelfwith brackets complete all as specified and directed. |
| 110 | S & F in repair double coat hook complete all as specified and directed. |
| 111 | S&F in repairs door seal with aluminium beading and 50 mm wide rubber sealcomplete fixed to aluminium/ Wooden doors complete all as specified and directed. |
| 112 | M&L for applying 2mm thick Birla / JK Putty in two layers on newly plastered wall surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed. |
| 113 | M&L for applying 2mm thick Birla / JK Putty in two layers on newly plastered ceiling surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed. |
| 114 | M&L for applying 2mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete. |
| 115 | M&L for applying 2mm thick Birla / JK Putty in two layers on old Ceiling surfaces including complete removal of existing Ceiling finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed. |
| 116 | M&L preparation of old painted surfaces and applying one coat of white wash on walls complete all as specified and as directed. |
| 117 | M&L preparation of old painted surfaces and applying one coat of white wash but on ceiling complete all as specified and as directed. |
| 118 | M&L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed. |
| 119 | M&L for preparation of newly plastered surfaces of ceilings and apply three coat of white wash complete all as specified and directed. |
| 120 | M&L preparation of old painted surfaces and applying one coat of oil bound distemper on walls complete all as directed. |
| 121 | M&L for Complete removal of existing treatmentand applying two coats of OBD over a coat of alkali resistant primer on wall complete all as directed by Engineer-in-Charge. |
| 122 | M&L for applying two coats of oil bound distemper on Ceiling surfaces over & includingon prepared surfaces including, rubbing with sand paper complete all as specified and directed. |
| 123 | M&L for preparation of old wood or wood based surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 124 | M&L preparation of old decorated wooden painted surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 125 | M&L for preparation of old steel surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 126 | M&L preparation of old decorated Steel painted surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 127 | M&L for two coats synthetic enamelled paint to new steel surfaces after preparation over a coat of red oxide primer area over exc 10cm in width or girth etc complete all as specified and directed. |
| 128 | M&L applyingonr coats Cement based paint on old decorated wall surfaces,includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed. |
| 129 | M&L applying two coats Cement based paint on old decorated wall surfaces,includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed. |
| 130 | M & Lfor2 coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, ofrequired shade and colour ( Plastic Emulsion Paint )complete, as per manufacturer\"s specification afterPreparation of plastered surface including a coat of primer on prepared surfaces including, rubbing with sand paper and applyingn. |
| 131 | M&L applying two coats of acrylic exterior weather proof emulsion paint over a coat of exterior primer on newly plastered wall surfaces/ old decorated wall surfaces, in case of old decorated wall surfaces includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed. |
| 132 | Demolition of Cement Concrete (unreinforced) of any description & in any position not otherwise specifically provided for complete all as specified & directed. |
| 133 | Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and directed |
| 134 | M&L for Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed complete all as specified and directed. |
| 135 | M&L for Cleaning the concerned RCC surface by means of wire brush to expose the concrete surface which should be free from all loose particles, dust, laitance, etc complete all as specified and directed. |
| 136 | M&L for Making corner fillets with Polymer modified cementitious (PMC) mortar (PMC:C:M :: 1:2:4 by weight) at all joints of horizontal and vertical surface and doing bore packing with PMC mortar complete all as specified and directed. |
| 137 | M&L for the joints of pipes and concrete/masonry are to be sealed with epoxy putty or epoxy mortar (PMC:C :: 1:2 by weight) and the same is semi-rounded upto 5mm above surface level all along the periphery of PVC pipes complete all as specified and directed. |
| 138 | M&L for application of one coat of Acrylic Polymer Modified Cementitious (APMC) slurry (APMC:C :: 1:2 by weight) coating over the RCC slab surface and carried upto finished floor level on vertical portion (walls) complete all as specified and directed. (Note : This coat is allowed to get dry for 4-6 hours.) |
| 139 | M&L for application of one coat ofAcrylic Polymer Modified Cementitious topping rendering (APMC:C:M :: 1:2:2) 1-1.5mm thick over the first coat Acrylic Polymer Modified Cementitious complete all as specified and directed.(Note : This coat is cured for 48 hours.) |
| 140 | M&L for Rendering 5 mm thick in CM 1:3 on RCC ceiling surface and finished even and smooth with out using extra cement complete all as specified and directed. |
| 141 | M&L Rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces,second layer (finishing coat)mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer\"s instructions and finish the surfaces even and smooth without using extra cement complete all as specified and directed.Note:Liquid WPC will be measured and paid separately. |
| 142 | M&L Water proofing treatment on \"Non approachable / non accessible and approachable roof\" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment,properly cleaning & drying the concrete surfaces complete (i) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm(ii)Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces complete all as specified and directed. (iii) Laying evenly over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction complete all as specified and directed.(iv) Applying two coats of bituminous aluminium paintincluding preparation complete all as specified and directed. |
| 143 | Taking down eaves gutters and rain water pipes of any size or pattern including all fittings etc complete all as specified and directed. |
| 144 | S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed. |
| 145 | S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed. |
| 146 | S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed. |
| 147 | S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 148 | S&F Stack clamps made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110 mm PVC pipe complete all as specified and directed. |
| 149 | S&F Stack clamps made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 75 mm PVC pipe complete all as specified and directed. |
| 150 | S&F PVC(SWR) bends, any radius of 110 mm bore without access door complete all as specified and directed. |
| 151 | S&F PVC(SWR) bends, any radius of 110 mm bore with access door complete all as specified and directed. |
| 152 | M/L PVC(SWR) Tee of110mm dia etc complete all as specified and directed. |
| 153 | S&F PVC(SWR) bends, any radius of 75 mm bore without access door complete all as specified and directed. |
| 154 | S&F PVC(SWR) bends, any radius of 75 mm bore with access door complete all as specified and directed. |
| 155 | S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door complete all as specified and directed. |
| 156 | S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 75 mm dia with access door complete all as specified and directed. |
| 157 | S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed. |
| 158 | S&F in repairs PVC (SWR)floor trap of diameter of outlet 75 mm, plain with gratingincluding jointing with solvent cement 75mm dia etc complete all as specified and directed. |
| 159 | S&F in repairs PVC (SWR) \"P\" trap for 110 mm dia etc complete all as specified and directed. |
| 160 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs /blankets, any thickness, including cover fillets complete all as specified and directed. |
| 161 | S&F 12 mm thick plain Gypsum Board False Ceiling with GI frame including all necessary drilling cutting to fix electric items complete all as specified and directed with following:-(a) GI Grid channel 30x25x20 mm of 24 gauge fixed with rawl plug and screw 450 mm centre to centre alongwith perimeter walls. (b) GI channel made to shape 50x40x40 mm of 24 gauge placed @ 600 mm centre to centre from perimeter at wall except long wall (in one span). (c) GI intermediate runners of size 45x10x10 mm of 24 gauge fixed @ 1200 mm centre to centre leaving frame of one side walls (in other span). (d) GI sheet 25 mm wide and 20 mm gauge suspended fixed with steel fastner to roof ceiling and 1200 mm centre to centre including pluging of RCC Slab. (e) 12 mm thick gypsum board filling joints with POP and finishing complete with two coat of plastic emulsion paint over one coat of primer on ceiling. |
| 162 | M&L for Cleaning and removing all scale and dirt, etc, from RCC/PVC tanks exc 250 ltr n.exc 500 ltr capacity incl washing of water tank with the use of Tank cleaning motor jet pressure machine and usingbleaching powder @ 0.25 Kgs per tank with writing the date of cleaning with any type of paint and from mouths of circulating pipes, including disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning,etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed. |
| 163 | M&L for Cleaning and removing all scale and dirt, etc, from RCC/PVC tanks exc 500 ltr n.exc 1000 ltr capacity incl washing of water tank with the use of Tank cleaning motor jet pressure machine and using with bleaching powder @ 0.50 Kgs per tank with writing the date of cleaning with any type of paint and from mouths of circulating pipes, including disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning,etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed. |
| 164 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, includingfixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor orthe side of waist slab with suitable arrangement complete all as specified and directed. |
| 165 | M&L for 12 mm thick designer anti-skid tread tiles for steps with bull nose edge and self-embossed grooves complete all as specified and directed. |
| 166 | M&L for 12 mm thick designer anti-skid riser tiles for steps with bull nose edge complete all as specified and directed. |
| 167 | M&L for 10 mm thick designer landing tiles with matching shade and colour with riser and treads complete all as specified and directed. |
| 168 | S&F in repairs door closer hydraulically regulated designation No 2, universal type, suitable for door shutter of weight between 36 to 60 Kg of aluminium (Die cast) body complete all as specified and directed. |
| 169 | Hacking out old broken glass (any thickness, size, quality or description)from metal frameincluding punching or drilling out old glazingpins/springclipsandprovidingand fixing new onesor stone, concrete or brick surrounds, glazed with putty or fixed with bead all as specified and directed |
| 170 | M&L 12 mm Toughned glass as in hinged doors , parttions automatic door and similar work incl cutting to shape , drilling holes required,complete all as specified and directed. |
| 171 | M&L in repairs for vitreous china wash basin, white,flat back, size 550 x 400 mm with pedestalincluding supply & fixing of brass chromium plated coupling 32 mm etc ,complete all as specified and directed. |
| 172 | S & F in repair Brass chromium plated wall mixer fancy typewith telephonic shower arrangement with connecting legs & wall flanges for 15 mm bore of pipe ,complete all as specified and directed. |
| 173 | S & F in repair Brass chromium plated fancy typehole bidet mixer (Basin mixer) with long bodypop-up waste system with 300 mm long braided hoses complete all as specified and directed. |
| 174 | Dismantling complete Centrifugal /Mono Block motor of any type and overhauling the pump re-threading of wornout holes of studs and providing over size studs with nuts & washers.Rematlling and balancing of shaft, replacement of gunmetal bush bearing and gland packingof pump set.and refitting the same after the repair/replacement duly all as specified and tested for smooth functioning of capacity 40 HP |
| 175 | All as per item No 174 above but capacity30 HP |
| 176 | All as per item No 174 above but capacity20 to 25 HP |
| 177 | All as per item No 174above but capacity10 to15 HP |
| 178 | All as per item No 174above but capacity 5 to 7.5 HP |
| 179 | All as per item No 174 above but capacity 1 to 3HP |
| 180 | Dismantling the power supply of electric motor any type including dismantling from pump and taking to workshop with necessary transportation and opening the complete motor and rewinding the rotor with super enameled copper wire as per the existing gauge with necessary insulation, sticks and varnishing, including replacement of shaft bearing 02 Nos and motor terminals plate/cable ducts complete of capacity 40 HP including painting complete all as directed. Note : Pump/Motor shall be dismantled and winding shall be tested continuity at site if winding fail/burnt is established than winding shall be cut at site before issuing gate pass. The coated rate deemed to included . |
| 181 | All as per item No 180above but of capacity30 HP electric motor any type. |
| 182 | All as per item No 180above but of capacity20 to 25 HP electric motor any type. |
| 183 | All as per item No 180 above but of capacity10 to 15HP electric motor any type. |
| 184 | All as per item No 180above but 5 to 7.5 HP electric motor any type. |
| 185 | All as per item No 180above but 1 to 3 HP electric motor any type. |
| 186 | Replacement of old rustedGI Column Pipe heavy grade of size 50 mm diain pieces of 3.3 metre long , lathe m/c threaded both endsin the bore/open wells completeall as specified and directed. |
| 187 | Replacement of old rusted heavy grade GI socketof size 50 mm dia ,complete all as specified and directed . |
| 188 | S&F in repair PVC insulated submerssible cable water proof flate type 3 core with standed copper conductor cable, 4 Sqmm, 1100 volts grade including cable lugs/joints, connection to submerssible motor and other end to aluminium armoured cable including jointing complete as directed . |
| 189 | S&F in repair HDPEBorecaps of size200/250mm dia ,complete all as specified and directed . |
| 190 | S&F in repairofsteel rope in submersible bore wells from motor to top edge of the bore well of size 6 mm dia(multi wire steenless steel) for holding of submersible pump motor set,complete all as specified and directed . |
| 191 | Supply and replacement contactor 16 Amps capacity 2 NO + 2 NC, AC 3 phase 415 Volts, 50 HZ ,complete all as specified and directed . |
| 192 | All as per item No 192 above but 25 Amps capacity,complete all as specified and directed . |
| 193 | All as per item No 192above but 32/35 Amps capacity,complete all as specified and directed . |
| 194 | All as per Item No 192 above but 40/50 Amps capacity,complete all as specified and directed . |
| 195 | S&F in repair Star Detla Timer 0-30 Seconds duration,complete all as specified and directed . |
| 196 | Supply and fix in replacement of MCB TP 40 amps,,complete all as specified and directed . |
| 197 | Supply and fix in replacement of electronic adjustable Cyclic timer 0-30 Seconds duration sutable to existing submersible motor panel board,complete all as specified and directed . |
| 198 | Supply and fix in replacement of dry Run Guard and overload protection with phase failure relay sutable to existing submersible motor panel board,complete all as specified and directed . |
| 199 | Supply and fix in replacement of Phase Monitoring Divice 440 volt 3 phase sutable to existing submersible motor panel board,complete all as specified and directed . |
| 200 | Supply and fix in replacement of Voltage Monitoring Divice 440 volt 3 phasesutable to existing submersible motor panel board,complete all as specified and directed . |
| 201 | S&F in repair DOL Starter for submersible pump set type MN -16 and relay range 9-15 Amps with contactor,complete all as specified and directed . |
| 202 | Supply and fix in replacement of Push Button sutable to existing submersible motor panel board complete all as specified and as directed |
| 203 | Supply and fix in replacement of Volt meter sutable to existing submersible motor panel board complete all as specified and as directed |
| 204 | Supply and fix in replacement of Ammeter sutable to existing submersible motor panel board complete all as specified and as directed |
| 205 | Supply and fix in replacement of Coupling Spider L-290 Heavy Duty complete all as specified and directed. |
| 206 | Supply and fix in replacement gun metal NRV of size 50 mm dia.Make : ZOLOTO/Leader/Upadhyay |
| 207 | Supply and fix in replacement over load relay 6 to 10 Amps for submersible motor panel board complete all as specified and as directed |
| 208 | Supply and fix in replacement over load relay 9 to 15 Amps for submersible motor panel board complete all as specified and as directed |
| 209 | Supply and fix in replacement over load relay 15 to 23 Amps for submersible motor panel board complete all as specified and as directed |
| 210 | Carrying out Chemical analysis test of water collected from bore wells through Govt approved lab complete all as specified and directed |
| 211 | Disconnecting the electric connection and taking out the submersible pump set from bore / open well of any capacity including GI column pipe complete and lowering down repaired motor with column pipe, welding joints and connecting electrical connection as directed and transportation of submersible pump set upto 7.5 HP 3 phase from pump house to any location in GMS area to contractors work shop repaired pump set for relowering, dismantling and carrying out necessary repairs complete aii as specified and directed |
| 212 | Dismantling of submersiblemotor 7.5 HP 3 phase from pump house at any location in GMSarea under AGE E/M GOS Yard, transporting to contractors workshop, dismantling and carrying out necessary repairs/replacement ofmotor as per the following :- (a) Cutting out existing winding of stator of submersible motor of any make and rewinding with same size of copper winding wire as existing as directed by the EIC. (b)Straightening the slot of starter of submersible motor of any make (c)Replacement of thrust washer and bearing complete of submersible motor of any make. (d)Replacement of worn-out bushes of submersible motor as per manufacturers design and specification. (e)Replacement of sand guard (f)Providing of sleeves in end plate of submersible motor (g)Replacement of cable gormmet (h)Replacement of water seal (i)Replacement of studs with nuts (j)Lathe work of motor shaft, turning to bring it to original size and shape and plastering of shaft of submersible motor for smooth functioning on described amps. Note : Pump/Motor shall be dismantled and winding shall be tested continuity at site if winding fail/burnt is established than winding shall be cut at site before issuing gate pass. The coated rate deemed to included . |
| 213 | All as per item No 212above but of capacity5 HP |
| 214 | All as per item No 212 above but of capacity3 HP |
| 215 | Dismantling of submersible pump7.5 HP capacity from pump house at any location in GMSarea under AGE E/M GOS Yard, transporting to contractors workshop, dismantling and carrying out necessary repairs/replacement ofpumps/Testing as per the following:-(a)Replacement of coupling complete (b)Overhauling of submersible pump and carrying out thefollowing repairs. (c)Lathe work including balancing of pump shaft and cutting of key slots (d)Re-threading of worn-out studs holes and providing over size studs with nuts (e)Replacement of bowel bushes (f)Replacement of neck ring (g)Replacement of steel distance pieces (h)Replacement of bowel(j)Replacement of head extension |
| 216 | All as per item No 215 above but of capacity5 HP |
| 217 | All as per item No 215 above but of capacity3 HP |
| 218 | Replacement of impeller upto 7.5 HP submersible pump setcomplete all as specified and directed |
| 219 | Flushing the bore well for flushing of silt, fine sand etc by air compressor of suitable capacity and pumping out turbidity till obtaining clear water all as directed and as per site requirement complete all as specified and directed |
| 220 | Supply and fixing street light fitting LED type 25 Wattnew generation in aluminium PDC housing, toughened glasscover with IP 66 protection complete in all respectwith GI tubing 25mm/40mm dia, mounting bracket with its clamp incl two coats of synthetic enamel paint over a coat red oxide primer and with all accessories, incl connecting of with 2 run of flexible aluminium/copper conductor of size 1.5 sq mm cable from fitting to junction box/conductor to street light as suitable on site, testing & commissioning complete all as specified and directed |
| 221 | Supply and fix Gland rope of size 8 mm to 12 mm for various motor complete all as specified and as directed |
| 222 | Supply and fixing LED flood light 200 watt Lumos II new generation LED with high luminous efficacy of 120 lm/w protected to IP-66 with front toughened glass complte in all respectwith GI tubing reqd in site, mounting bracket with its clamp incl two coats of synthetic enamel paint over a coat red oxide primer and with all accessories, incl connecting of with 2 run of suitable flexible aluminium/copper conductor of size 2.5 sq mm or fixed in appropriate size of PCC block made with PCC 1:3:6 with fixing arrangement suitable on site, testing & commissioning complete incl taking down old unsv any type and make complete all as specified and directed |
| 223 | M & L for preparation of old steel surfaces and applying one coat of synthetic enamel paint in position to allsurfaces for pump sets complete including base frames , Suction and discharge pipe lines, sluice valves , NRV ,including Iron removal plant , LT Panel Board etcpump house, writing of SM/MES No. neat and clean,visible size of letters and complete all as specified and directed. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
