|
| 1 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard/dense comlete all as specified and directed. |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil comlete all as specified and directed. |
| 3 | Description same all as per item No 2 above but for each additional 1.5m or part thereof in depth beyond the first 1.5m in hard/dense soil complete all as specified and directed. |
| 4 | M&L for PCC (1:4:8) Type D2 (using 40 mm graded stone aggre-gate) as in foundations, filling and mass-concretecomplete all as specified and directed. |
| 5 | M&L for formwork for rough finish to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to battercomplete all as specified and directed. |
| 6 | M&L for formwork for rough finish to sides of pillars, posts, struts, piers, columns and stanchionscomplete all as specified and directed. |
| 7 | M&L for formwork for rough finish to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etccomplete all as specified and directed. |
| 8 | M&L for formwork for rough finish to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed. |
| 9 | M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 10 | M&L for mild steel TMT bars 5 to 10mm dia bars as in stirrups cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 11 | M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles, raft etc and mass concrete complete all as specified and directed. |
| 12 | M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 13 | M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in floor/ roof beam, cantilevers, lintel over 1.5m span complete all as specified and directed. |
| 14 | M&L for PCC (1:2:4) type B1 using 20 mm graded stone aggregate precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars,bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and Set in cement mortar 1:4with joints to match complete all as specified and directed. |
| 15 | M&L for RCC (1:2:4) Nominal mix (using 20mm graded stone aggregates) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, and in shelves complete all as specified and directed. |
| 16 | M&L for brick work with old size full bricksubclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed. |
| 17 | M&L for brick work with old size half bricksubclass ‘B’ burnt clay bricks, straight or curved on plan any radius, built in CM (1:4) complete all as specified and directed. |
| 18 | M&L for 5 mm thick rendering on fair facesof brick work or concrete surfaces in CM (1:3) as in ceiling and fininshed even and smooth with out using extra cement complete all as specified and directed. |
| 19 | M&L for 15mm thick plastering onbrick wall in CM (1:4), surface finished even and smooth with out using extra cement mixed with WPC as per manufacturer\"s instruction complete all as specified and directed.Note :- WPC shall be measured and paid separately as supply only. |
| 20 | M&L for 10 mm thick rendering on brick or concrete surfaces in CM (1:6)fininshed even and smooth with out using extra cement complete all as specified and directed. |
| 21 | Supply only WPC integral water proofing compound (Liquid type) complete all as specified and directed. |
| 22 | M&L for preparing newly plastered surfaces of wall and applying two coats ofcement base paint over a coat of cement primer complete all as specified and directed. Note :-The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. |
| 23 | M&L for preparing newly plastered surfaces of wall and applying three coats ofwhite washcomplete all as specified and directed. Note :-The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge.The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. |
| 24 | M&L for moorum / red bajri filling in, floor or pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 25 | M&L for hard core of broken boulders/stone of gauge n exc. 63 mm, deposited, spreading, levelling watering and well ramming to true surface in layers not exceeding 15 cm thick each layer complete all as specified and directed. |
| 26 | M&L for 100 mm thick PCC (1:4:8) type D2, (using 40 mm graded stone agg) as in sub base of floor complete all as specified and directed. |
| 27 | M&L for 40 mm thick PCC (1:2:4) type B1, (using 20 mm graded stone agg) as in sub base of floor complete all as specified and directed. |
| 28 | M&L for non skid, joint free, coloured ceramic tiles7-8mm thick (Square/Rectunglar), as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles laid with and including over 15mm thick screed bed in CM (1:6), area of each tiles shall be of following complete all as specified and directed :- |
| 29 | Area of each tile exc 0.06 Sqm but not exc 0.11 Sqm. |
| 30 | M&L for coloured glazed ceramic tiles of any design and pattern, 300x450x 7 to 8mmthick, as in dado etc including 10mm thick rendering in CM (1:4), set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed.Note: Shade of the tiles including Colour, design and pattern shall be got approved by AGE(I) |
| 31 | M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement,complete all as specified and directed. |
| 32 | S&F rolled mild steel section for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-Acomplete all as specified and as directed.Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. |
| 33 | S&F Plates (plain or chequered)channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 -W (Gde- E- 250) quality A complete all as specified and directed |
| 34 | M&L for mild steel screw bolts (machine made) dia of neck length 16 to 20mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5 cm and n exc 30cm long complete all as specified and directed. |
| 35 | S&F mild steel work as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 steel with and including necessary drilling holes etc complete all as specified and directed.Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account. |
| 36 | M&L for twocoats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed. |
| 37 | S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick ofcolour as approved, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 38 | S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick ofcolour as approved having tensile strength of 550 Mpa, AZ-150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 39 | Returning, filling in, soil including spreading, levelling, watering and well ramming in layers not exc 25 cm.complete all as specified and directed. |
| 40 | Removal of surplus soil to a distance exc 250 mtr nexc. 500 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed. |
| 41 | Removal of surplus soil to a distancenexc. 50 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed. |
| 42 | M&L for 18-20mm thick granite stone slab white and black table rubbed and mirror finish polished with and including necessay notching, chamfering the edges in steps, jambs, pillars, window-cills, cooking platforms, floor, wall and like bedded over and including 20 mm thick screed bed in CM (1:6) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 43 | M&L for Rounding to edges of stone slabs one edge,such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 44 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable andvariation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately. |
| 45 | 65 mm x 100mm size |
| 46 | S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately |
| 47 | S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet, reinforced with MS square tube, fixing in same opening complete as all as specified and directed. |
| 48 | S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top, bottom and side rails, MS frame shall be covered with heat molded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fixed in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement and fixing in the frame at site complete all as specified and directed. |
| 49 | S&F factory made steel ventilators with top hung shutter including box typehinges with steel handle and Z-section handle and steel peg stay complete with glazing bars, dovetailed or welded including a shop coat of red oxide zinc chrome primer complete all as specified and directed. |
| 50 | S&F windows & ventilators, fabricated from rolled formed GI Section made of Galvanised steel colour coated (PPGI Sheets) (Base steel as per IS 513 ‘’D’’ quality). Galvanised as per IS 277 with Zinc of 90 Gsm/SqMt w. PAINT: Pre-Painted sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick.GI Section of 0.58mm thick inDouble rebate windows in which both glazed shutter andgauge (flymesh) shutter, 74 X 60mm outer frame, Mullion 72 x 49mm, Glazed shutter 48 x 22mm, Flymesh 41 x 22mm, Beading with round ends for Glass Fixing 12 x 12mm in fixed portion and the outer frame and mullions to have rebate for glazed/ gauzed shutters the sections cut to length metre joined with corner PolyVinylChloride brackets centre mullion fixed with PolyVinylChloride Mullion caps. Glass of 4mm thick plain float glass fitted with Ethylene Propylene Diamine Monomer in glazed shutterand wiremesh of Stainless steel of 36 guage to fix mesh in mesh shutter using VC Black Gypsum Drywall screws and Spoon profile of 0.58mm GI Sheet. Corners of the windows should be joined with corner brackets made of polyvinylchloride with crca of zinc phosphate coat.Each glazed shutter and fly mesh shutter shall be provided with SS Pivot Hinges 2 in each,PolyVinylChloride handle 1 in each and Powder coated Peg stay in Glass shutter.Window shall be provided with Powder coated MS Grill/Guard Bars made of 10mm MS Sq Bar welded to 6 x 12mm MS Flat with countersunk holes at both vertical ends . Gap between the bars should not be more than 150mm.Window frames shall be fixed to brick / concrete masonry by using nylon self expension caps & 75/100 mm MS screwsafter drilling in walls. VC Black Gypsum Drywall screws should be used while fixng corner brackets,stay,hinges,mullion caps of windows complete all as specified and directed. |
| 51 | S&F250 mm long anodised aluminium sliding door bolt (ISI marked) with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections ofcomplete all as specified and directed. |
| 52 | S&F 200 mmanodised aluminium barrel tower bolts (ISI marked) of extruded sectioncomplete all as directed and specified |
| 53 | S&F 100 mm long butt hinge, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed. |
| 54 | S&F 75 mm long butt hinge, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed. |
| 55 | S&F 150 mm anodised aluminium handles cast type complete all as directed and specified. |
| 56 | S&F 100 mm anodised aluminium tower bolt of extruded section complete all as directed and specified. |
| 57 | S&F 3 mm thick figured glass, pin headed type and glazing with oil putty /wooden beads in square n. exc 0.5 sqm in each pane complete all as specified and as directed. |
| 58 | S&Fvitreous china counter sunk wash hand basin,snow white of size 560x 470 x 190mm excluding taps, waste pipe but including waste pipe and coupling complete all as specified and directed. |
| 59 | S&F Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed. |
| 60 | S&Fvitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed. |
| 61 | M&Lfor 75mm dia cast iron Nahani trap with grating including jointing to waste pipe fixed in PCC (1:2:4) type B1, complete all as specified & directed. |
| 62 | S&F PVC (SWR) P trap, out let dia 110mm, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 63 | S&F PVC (SWR) bends any radius including necessary cutting in brick wall and making good to match with existing surface of following size complete all as specified and as directed :- |
| 64 | 75 mm bore |
| 65 | 110 mm bore |
| 66 | S&F PVC (SWR) vent cowl of75 mmbore complete all as specified and as directed. |
| 67 | S&FPVC (SWR) junction single, (single T)equal or unequal of following size complete all as specified and as directed :- |
| 68 | 110 mm bore |
| 69 | 75 mm bore |
| 70 | S&FPVC (SWR) pipes single socketed in any length with rubber ring joints and laid in trenches or in floor or fixed to wall of following size complete all as specified and as directed :- |
| 71 | 75 mm bore |
| 72 | 110 mm bore |
| 73 | S&FPVC valveless, syphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approvrd by GE complete all as specified & directed. |
| 74 | S&FPVC connection 15 mm size with PTMT nut of 450 mm length complete all as specified and directed. |
| 75 | S&F15mm bore Stop valves (angle valve cock), cast copper alloy, fancy type, chromium plated with cupscrewed down high pressure with crutch or butterfly handleor concealed screwed both ends for iron pipe or for unions complete all as specified and directed.Note for all CP item :- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. |
| 76 | S&F 15 mm borepillar taps, cast copperalloy, with capstan heads, chromium plated , Fancy type screwed down for pipe,high pressure , with or without lettered \" \"HOT\" or \"COLD\" with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed. |
| 77 | S&F15 mm bore bib taps, chromium plated, fancy type, cast copper alloy with crutch handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed . |
| 78 | S&F swivel shower rose PTMT any colour 125mm size for fixing with 15 mm bore pipe having min weight 40 gms complete all as specified and as directed. |
| 79 | S&F shower arm of PTMT, any colour, 195mm long, 15 mm bore, with bend of 45 degree with flange having min weight 40gms complete all as specified and as directed. |
| 80 | S&F15 mm bore galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenchescomplete all as specified and as directed. |
| 81 | S&F20 mm bore galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenchescomplete all as specified and as directed. |
| 82 | S&Fin repair soap dish mild steelCP fixed to plugs with CP screwscomplete all as specified and directed. |
| 83 | S&F 5mm thick bevelled edge best quality looking mirror of size 600x450 mm mounted over 6mm thick commercial quality ply wood and fixed to wooden plug with CP brass screw and cup washer, complete all as specified and directed. |
| 84 | S&Fchromium plated brass tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed. |
| 85 | S&F grating doom 100mm dia of PTMT (with waste hole or without waste hole)(Min wt 25 gms) complete all as specified and directed. |
| 86 | S&F 1000 ltr capacity rotational moulded polyethylenewater storage tanks triplelayered white (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plasttic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/2.0mm-455gms/40-690gms) including dismantling of water tanks complete all as specified and directed |
| 87 | M&L for20cm x 20cm x 25mm thick rubber moulded coloured glossy finish chequered cement concrete tiles, ISI Marked, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. |
| 88 | M&L for100 mm thick PCC (1:3:6) Type C2 (using 40 mm graded stone aggre-gate) as in sub base of floor, finish even and rough to receive the top layer complete all as specified and as directed. |
| 89 | Excavating over areas, n exc 1.5m deep and gettingout in hard/ dense soil complete all as specified and directed. |
| 90 | Add to item No 81 above but for each additional 1.5m or part thereof in depth beyond the first 1.5m in hard/ dense soil complete all as specified and directed. |
| 91 | M&L for PCC (1:3:6) Type C2 (using 40 mm graded stone aggre-gate) as in foundations, filling and mass-concretecomplete all as specified and directed. |
| 92 | M&L for 150 mm bore reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as secified and directed. |
| 93 | M&L for 200mm bore reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as secified and directed. |
| 94 | M&L Brickwork with sub class ‘B’ bricks in one brickthick honey comb walling, built in CM 1:6 complete all as secified and directed. |
| 95 | M&L concrete bed to drain pipes in PCC (1:3:6) type C2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid on slope and tested for 150 mm bore of pipe line complete all as specified and directed. |
| 96 | M&L concrete bed to drain pipes in PCC (1:3:6) type C2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid on slope and tested for 200 mm bore of pipe line complete all as specified and directed. |
| 97 | M&L for 15 mm thick rendering on brick wall in CM (1:4)fininshed even and smooth with out using extra cement complete all as specified and directed. |
| 98 | M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast,water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed. |
| 99 | M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) and set in CM (1:6) including necessary fair finish formwork complete all as specified and directed. |
| 100 | M&L for extra for forming fair finished drain, or channel, 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred, stopped ends, complete all as specified and directed. |
| 101 | M&L for formworkfor rough finish to soffits of suspended slabs such as roof slabs, floor slabs, landing slab and similar work, not exceeding 200 mm thick complete all as specified and directed. |
| 102 | M&L for RCC (1:2:4) Nominal mix type B0(using 12.5 mm graded stone aggregates) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, and in shelves complete all as specified and directed. |
| 103 | M&L broken bricks for loose filling of gauge 40 to 80 mm for soak wellcomplete all as specified and directed. |
| 104 | M&L Bricks, sub class B,laid on edge in floorsold size bricks Bedded andjointed in Cement mortar 1:6 and pointedin 1:3 cement mortar complete all as specified and as directed. |
| 105 | M&L for PCC (1:2:4) type B-0, using 12.5 mm graded stone aggregate as in surface channel and drain including saucer drain and toe wall etc complete all as specified and directed. |
| 106 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power UG cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size10.00 sq mm 2 core complete as specified and directed. |
| 107 | M&L for sand cushioning with dry and clean fine river sand for underground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and directed.Note:- Punned thickness shall be considered for payment purpose. |
| 108 | Supply and laying cable protection bricks, common burnt clay sub class \"B\" designation 75 for protection of UG cable laid in trenches with axis of the bricks perpendicular to the axis of the cable complete all as specified and directed. |
| 109 | S&F 15 mm gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed,complete all as specified and directed. |
| 110 | Supply, fixing, laying, jointing & testing of galvanised iron water tubing \"Light grade\" conforming to IS-1239 with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc as required complete fixed checknuts, caps, plugs etc as required complete fixed to walls and ceilings, laid in trenches/under floor/under road or floors complete all as specified and directed for the 32 mm bore pipes. |
| 111 | Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with continuous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed rigid PVC conduit(ISI marked) ,duly cutting chases & concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia(Color coding of wires shall be Phase, neutral and earth wire all as specified ) including metal flush box made of GI sheet and white cover with making good the disturbs surfaces of wall/floor/ceiling complete all as specified and directed for the following.Note: Flush box and cover plate should be of same make all as approved for switches/sockets. |
| 112 | One light/fan/bell point controlled by one No modular type switch 6 Amps single pole one way. |
| 113 | One socket out let 5/3 Pin 5 Amp controlled by one switch on independent board |
| 114 | All as per item No 103 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor1100 V grade PVC insulated FRLSH but unsheathed single core for16 Amps power point on independent board and 2.5 sqmm FRLSH cable as earthwire. |
| 115 | S & F switch Modular single pole,one way 6 Amps , 1 module,230 volts, 50 hzcomplete all as specified and directed. |
| 116 | Supply and fix Modular switch 1 way 16 Amps, 1 module, 230 volts, 50 Hz complete all as specified and directed. |
| 117 | Supply and fixModular Socket outlet, 5A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed. |
| 118 | Supply and fixModular Socket outlet, 16A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed. |
| 119 | S&F ceiling rose 3 terminal / PVC/ polycarbonate, isolated body complete all as speccified and directed |
| 120 | S&F angle Lamp holder (with metal ring), insulated body, of PVC/ Polycorbonate with back plate (ISI Marked) suitable for batten fittingcomplete all as specified and as directed. |
| 121 | Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia 20 mm complete all as specified and as directed. |
| 122 | S&F surface mounted LED luminiare, 20 watt with all accessories having polymer extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose complete all as specified and directed. |
| 123 | Supply and fixLED building security light 1 x 20 W housing made out of pressure die-cast aluminium alloy with toughned glass, IP 66 protection working on 240 volts, 50 Hz, consisting of reflecting lamps wired with appropriate driver PF> 0.95 having over voltage protection upto 440 volt, surge protection level > 10 KV, thermal short circuit protection THD< 10% made up of long life LED chip (SMD) in modular with Ra< 70,beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminaire efficiency> 120 luminous /watt power LED should be of more than 01 watt CCT should be between 5700° K- 6500° K including fixed on wall with 1.2 mtr 32 mm GI pipe bracket & 02 Nos MS clamp made out of F1 40 x 6 mm or as directed including connecting with 1.5 sqmm , 3 core, PVC insulated copperconductor cable 1100 Volt grade from ceiling box to light complete all as specified and as directed by Eng-in-Charge (i) The firm has to given warranty of street light fittings including driver minimum for 03 years for any defect developed during the period. (ii) The contractor Shall submitt the third Party LM 79 report from any NABL approved laboratory (iii) The fiitting should have BIS , CRS No(iv) Connection to luminaire shall be done in suitable PVC connector within the bracket/luminaire end and are inclusive in above. |
| 124 | S&F MCB DB SPN 8 way with 200 amp 240 volts in sheet steel enclosure.double door type complete all as specified and directed. |
| 125 | S&F MCB , SP, AC, 240 volts of 06 to 32Amps capacity 10KA, \"C\" series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 126 | S&F MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, \"B\" series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 127 | Supply and fixing exhaust fan made of study Engineering plastic complete with louvers shutter, AC single Phase 230/240 Volts,50 HZ RPM 1200 copper windingof 300 mm sweep complete including making hole and making good the distrubed surface of wallcomplete all as specified and directed. |
| 128 | M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground, earth pit not less than 2.25 mtr depth below ground level at any type of strata with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate, connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC (1:3:6) type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM (1:4) funnel with wire mesh, RCC pit cover of 320 x 320 x 80mm size PCC (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed. |
| 129 | Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick reinforced with XPM weighing not less than 4kg/sqm in lieu of CI cover.(ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items. |
