|
| 1 | Taking down Cement Plaster of any description on Brick Walls, Stone Walls Concrete Surfaces including Racking out Joints, hacking for Key, scrubbing down with Water,etc. complete removal of debris outside MD land complete all as specified and directed by Engr-in-Charge. |
| 2 | M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 incl finished even and smooth (without using extra cement) incl mixing with water proofing compound complete all as specified and directed by Engr-in-Charge. (Note : water proofing shall be measured & paid separately). |
| 3 | M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 incl finished even and smooth (without using extra cement). |
| 4 | Supply only integral waterproofing compound of approved make complete all as specified and directed by Engr-in-Charge. |
| 5 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete removal of debris outside MD land complete all as specified and directed by Engr-in-Charge. |
| 6 | S&F non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge. |
| 7 | M & L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick to 8mm mmthick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick backing coat in Cm 1:4 all as specified and directed by engineer in charge |
| 8 | Demolition of cement concrete (unreinforced)in ground floor and paving etc n.exc 15cm thick above or below ground level including terrazzo finish wherever existing complete all as specified and directed by Engr-in-Charge. |
| 9 | M&L for 25mm thick Cement concrete 1:2:4, type B0 (12.50mm graded stone aggregate) for floor as in sub base or levelling course for floor tiles complete all as specified and directed by Engr-in-Charge. |
| 10 | Demolition of stone slabs of any description or thickness in floors laid bedded and pointed in any mortar etc. complete removal of debris outside MD land complete all as specified and directed by Engr-in-Charge. |
| 11 | M&L 20mm thick Granite work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit including 15 mm thick screed bed in CM 1:6 and Rounding to edges complete all as specified and directed by Engr-in-Charge. |
| 12 | M&L PCC 1:3:6 type C2 75 mm thick (using 40mm graded aggregate) as in Plinth protectionfinshed the concrete surface even and smooth W/O using extra cement complete complete all as specified and directed by Engr-in-Charge. |
| 13 | Taking down chowkats or frames with shutters (with out taking off shutters from the frames) exc 1.5 Sqm but n. exc 4 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 14 | Taking down chowkats or frames with shutters (with out taking off shutters from the frames) n. exc 1.50 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 15 | S&F pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and directed by Engr-in-Charge |
| 16 | M&L for PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in filling of chowkats complete all as specified and directed by Engr-in-Charge |
| 17 | S&F Powder coated aluminium sliding window (three way) frame & shutter with glazed shutter and without wiremesh shutter /skeleton section with the following details :-(i) Aluminium frame section 116x36.50x1.80mm.(ii) Aluminium shutter glazed/skeleton section 50x20x1.50mm thick.(iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars complete all as specified.(iv) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape.(v) 4mm thick glass orinary quality and fixed with rubber gasket for with glazed shutter etc.(vi) Stainless steelwire mesh 0.36mm nominal dia avg aperature 1.14mm and fixed with rubber gasket for without glazed shutter etc.(vii) Aluminium disc /bow hanle and locking system complete |
| 18 | S&F Powder coated aluminium Ventilator (partially fixed glazing and Partially louvered glazing) with the following details :-(i) Aluminium frame section 45x25x1.80mm.(ii) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape.(v) 4mm thick frosted glass orinary quality (partially fixed glazing and Partially louvered glazing) and fixed with rubber gasket for with glazed shutter etc. |
| 19 | S&F 2nd class hard wood glazed and skeleton shutters, 35mm thick, open rebated & prepared to receive wire gauge (with sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitread beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I, section 8, clause 8.24- (a), supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge. |
| 20 | S&F 30 mm flush door shutters, solid core construction with block board core and plywood face panels, commercial type on both sides |
| 21 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engr-in-Charge |
| 22 | S&F Factory made solid panel pvc doorshutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing |
| 23 | S&F Butt hinges 100mm stainless steel , medium weight complete all as specified and directed by Engr-in-Charge. |
| 24 | S&F 150mm long aluminium, anodized barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge |
| 25 | S&F 150mm long aluminium handles, cast type anodized complete all as specified and directed by Engr-in-Charge. |
| 26 | S&F 300mm aluminium alloy, anodized, sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engr-in-Charge |
| 27 | S&F 300mm MS ordinary rat tail rod pattern spring includingroller and rollerplatecomplete all as specified and directed by Engr-in-Charge |
| 28 | S&F stailess steel wire cloth, 0.36 mm nominaldia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples with wodden beading on wooden shutter or with screws to steel / aluminium shutter complete all as specified and directed by Engr-in-Charge. |
| 29 | Taking up or down steel tubing and connections 15mm bore complete all as specified and directed by Engr-in-Charge |
| 30 | Taking up or down steel tubing and connections 20mm bore complete all as specified and directed by Engr-in-Charge |
| 31 | S&F 20m outer dia CPVC Pipe (ISI Marked) SDR II & plain CPVC SDR II fittings fixed on wall, celing or floors complete all as specified and directed by Engr-in-Charge |
| 32 | S&F 25m outer dia CPVC Pipe (ISI Marked) SDR II & plain CPVC SDR II fittings fixed on wall, celing or floors complete all as specified and directed by Engr-in-Charge |
| 33 | S&F in Repair Vitreous China Wash hand basin, white flat back size 550x400 mm including brackets(including Pillar Tap 15 mm bore Chromium plated fancy type with capstan heads, 32 mm waste coupling brass chromium platedsuitable for wash hand basins, with long screwed shanks and fly nuts & PVC waste pipe) and bedded in cement morter and fixed on CP cantilever brackets all as specified & directed by Engineer-in-charge. |
| 34 | S&F in Repair Vitreous China Wash down water closet pan pedastel pattern (EWC) white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete all as specified & directed by Engineer-in-charge. |
| 35 | S & F in repairs vitreous China squatting pan,‘Orissa’ pattern, size 580 x 440 mm white, withintegral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor with recessed bottom and connection to drain or out going pipe and flushing pipe complete all as specified and directed by Engr-in-Charge |
| 36 | S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including making good to floor complete all as specified and directed by Engr-in-Charge. |
| 37 | S&F in repairs 10 ltr capacity PVC Low level flushing cistern including 32mm dia PVC flush pipe, fixing in position with PVC connection pipe of 15mm x 600mm long etc complete all as specified and directed by Engr-in-Charge |
| 38 | S&F in repairs 600mm x 450mm beveled edge mirror of selected quality, glass 5mm thick, mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 39 | S&F in repairs 15mm Bib taps chromium plated fancy type cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for union.Make:Prayag 8306 or equivalent complete all as specified and directed by Engr-in-Charge |
| 40 | S&F in Repair 15mm Bore Stop Valves / Angle Cock Fancy Type Chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends complete all as specified and directed by Engr-in-Charge. |
| 41 | S&F in repairs Brass chromiun platedtubular towel rail, 20mm dia ‘D’ type, 60CM long between flanges complete all as specified and directed by Engr-in-Charge |
| 42 | S&F in repairsShower rose with brass chromium plated shower rose with or without swivel joints, 100mm size including fixing to steel pipe or union complete all as specified and directed by Engr-in-Charge. Make: Cera Cat No-F7020304 or Equivalent |
| 43 | M&L preparation of newly plastered surfaces of wall and applying two coats ofdistemper oil bound over a coat of 1mm thick birla wall care putty over a coat of alkali resitant primer coat on plastered surface complete all as specified and directed by Engr-in-Charge |
| 44 | M&L complete removal of existing treatment of old plastered surfaces of wall and applying two coats ofdistemper oil bound over a coat of 1mm thick birla wall care putty over a coat of alkali resitant primer coat on plastered surface complete all as specified and directed by Engr-in-Charge |
| 45 | M&L for preparation of newly plastered wallsurfaces and applyingtwo coats ofcement base paintcomplete all asspecified and directed. |
| 46 | M&L for preparation of Old plastered wallsurfaces and applying one coats ofcement base paintcomplete all as specified and directed. |
| 47 | M&L Preparation of Old decorated surface and applying two coat of white wash on ceiling etc complete and as directed. |
| 48 | M&L Preparation of New Wood surface and applying two coats of synthetic enamel paint over a coat of pink primer over 10cm width or girth complete all as specified and directed by Engr-in-Charge. |
| 49 | M&L forpreparation of new steel surfaces of any description over 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer, all as specified and directed by Engr-in-Charge. |
| 50 | S&F in repairs PVC (SWR) floor trap 75mm dia plain with steel grating including jointing with solvent cement etc complete all as specified and directed by Engr-in-Charge |
| 51 | S&F in repair 110mm dia PVC (SWR) pipes single socketed in any length with rubber ringjoints fixed to walls etc complete all as specified and directed by Engr-in-Charge |
| 52 | S&F in repair 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls etc complete all as specified and directed by Engr-in-Charge. |
| 53 | S&F PVC (SWR) bends 110mm dia any radiuswith access door complete all as specified and directed by Engr-in-Charge |
| 54 | S&F PVC (SWR) bends 75 mm dia any radius with access door complete all as specified and directed by Engr-in-Charge |
| 55 | S&F PVC (SWR) junction single,(Single T) 110mm dia equal or unequalwith access door complete all as specified and directed by Engr-in-Charge |
| 56 | S&F PVC (SWR) junction single,(Single T) 75mm dia equal or unequalwith access door complete all as specified and directed by Engr-in-Charge |
| 57 | S&F PVC (SWR) branch piece, (Single Y) 110mm dia equal or unequalwith access door complete all as specified and directed by Engr-in-Charge |
| 58 | S&F PVC (SWR) branch piece, (Single Y) 75mm dia equal or unequalwith access door complete all as specified and directed by Engr-in-Charge |
| 59 | S&F PVC (SWR) vent cowl 75/110mm bore complete all as specified and directed by Engr-in-Charge |
| 60 | Taking down copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc. complete all as specified and directed by Engr-in-Charge |
| 61 | M&L for point wiring with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC Concealed conduit (medium duty ISI marked,not less than 20 mm dia) with all fittings such as tee, bends, etcall as per IS, terminated in & including new sunk type pressed steel terminal boxes concealed in wall for mounting fittings like switches, sockets, regulators etc with and including 3mm thick phenolic laminated sheet top cover, complete all as specified and as directed for the following :-(a) One light/Exhaust fanpoint controlled by one 5 Amps switch one wayNote : Cost of cutting/leaving forming chases for conduits, sinking for boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item. |
| 62 | (b) One 3 pin socket point 5 Amp on independent board |
| 63 | (c) One 3 pin socket point 5 Amp on same board with other switches. |
| 64 | All as per item No. ___ above but with 2.5sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor for 3 pin 15 A socket outlet on independent board complete all as specified and directed. |
| 65 | S&F Switch piano, flush button single pole, 5 Amps one way complete all as specified and directed by Engr-in-Charge. |
| 66 | S&F Switch socket combination flush type 5 Amp 2 in 1 complete all as specified and directed by Engr-in-Charge. |
| 67 | S&F Switch socket combination flush type 5/16 Amps 5 in 1 complete all as specified and directed by Engr-in-Charge. |
| 68 | S&F Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC square blocks complete all as specified and directed by Engr-in-Charge. |
| 69 | S&F in replacement LED tube light fitting of20 watts 6000K , 230 volt, withaluminium extruded channel powder coated with diffuser for glare free light complete with wall mounting all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmmwith all as specified and directed by Engr-in-charge. |
| 70 | S&F in replacement LED tube light fitting of10 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. |
| 71 | S&F bldg securitylight fittings 1x 35 Watt Ac 230v out door typeLED street light with high pressuredie cast aluminium and heat ressistent complete with driver ,lamp bracket with impact and corrosion resistentincluding thermal managment in multiple optics complete, IP65/66 and wired with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed. |
| 72 | S&F street light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 73 | M&L forSub main wiring with 2 runs of 6.0 sqmm, single core, PVC insulated & unsheathed cable FRLS conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in existing non metallic PVC grey conduit fixed on wall with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution boardas ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed. |
| 74 | S&F in replacement Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way horizontal type, Double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as specified and directed. |
| 75 | S & Fin replacement MCB single pole 6 to 32 Amps 240 volts, 10 kA rupturing capacity providing in DB completeall as specified and directed by Engr-in-charge. |
| 76 | S & Fin replacement MCB single pole & neutral 40 to 63Amps 240 volts, 10 kA rupturing capacity providing in DB complete andall as specified. |
| 77 | Taking down and Refixed any type and size of Exhaust fan in any description after making necessary connections & testing on completion and making good distrubed surfaces of wall, floors, etc complete all as directed. |
| 78 | Rewinding of Exhaust fan with appropriate size of copper enamelled wire including varnishing ,heating with proper insulation complete and testing all as specified and directed . |
| 79 | M&L, Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thickburied directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 4 mm dia by means ofof nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia light grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified and directed. |
