|
| 1 | Maintenance of Command Swimming Pool of size 50m x 21 m, with combined swimming and diving basin, the water depth is 1 m at shallow end increasing to 5 m at deep end by following steps (a) Cleaning the surfaces by scraping and using chemicals such as bleaching, (b) Cleaning of swimming pool side walls, (c) skimmer channel by pool cleaner and cleaning of bottom including deep slope surface by under water cleaner (d) Removing sediment particle from bottom by using suction sweeper by deploying required number of manpower who are well conversant with swimming pool cleaning process and specialized in diving and deep cleaning, without disturbing the swimming pool schedule of operation complete all as specified and as directed by Engineer-in-Charge. |
| 2 | Item No. 01 (contd--)Note :- The quoted rate shall be inclusive of the following :- (a) Cleaning process shall be carried out in two days during weekly maintenance days of the swimming pool as decided by the user unit or as directed by Engineer-in-Charge. Total work carried out during the two maintenance days of a week shall be measured as one unit job and the quoted rate is deemed to be inclusive of this aspect and nothing extra shall be paid on this account.(b) T & P such as oxygen mask, air compressor, oxygen cylinder, safety rope, brush, wire mesh and all accessories required for under water cleaning of slope area at deep end including diving persons life insurance and any emergencies etc.(c) Cleaning of swimming pool should be carried out minimum once in a week and as and when ordered / directed by Engineer-in-charge / GE as per site requirement by deploying required manpower.(d) Cost of cleaning material and chemicals required for cleaning shall be deemed to be included in the quoted rate(e) After every cleaning the following water quality and standard parameters to be checked and confirmed to the Engineer-in-Charge as per TI 03/2010 and cost of testing equipment shall be deemed to be included in quoted rate:- (i) Ph :7.4 to 7.6 (ii) FRC : 0.5 to 1 PPM (iii) Total Alkalinity: 75 ppm minimum (iv) Total Hardness: 200 ppm minimum (v) TDS: 500 ppm minimum(f) Testing equipment such as pH meter, Chlorine test kit, Water Alkalinity test meter, Water Hardness test meter and TDS meter should be made available at Swimming Pool and cost of the same is deemed to be included in quoted rate and nothing extra shall be paid on this account. |
| 3 | Maintenance of SVN colony Swimming Pool of size 25m x 13.5 m, without a separate diving pool, the water depth is 1 m at shallow end increasing to 4 m at deep end by following steps (a) Cleaning the surfaces by scraping and using chemicals such as bleaching, (b) Cleaning of swimming pool side walls, (c) skimmer channel by pool cleaner and cleaning of bottom including deep slope surface by under water cleaner (d) Removing sediment particle from bottom by using suction sweeper by deploying required number of manpower who are well conversant with swimming pool cleaning process and specialized in diving and deep cleaning, without disturbing the swimming pool schedule of operation complete all as specified and as directed by Engineer-in-Charge. |
| 4 | (Item No 02 Contd--)Note :- The quoted rate shall be inclusive of the following :- (a) Cleaning process shall be carried out in two days during weekly maintenance days of the swimming pool as decided by the user unit or as directed by Engineer-in-Charge. Total work carried out during the two maintenance days of a week shall be measured as one unit job and the quoted rate is deemed to be inclusive of this aspect and nothing extra shall be paid on this account.(b) T & P such as oxygen mask, air compressor, oxygen cylinder, safety rope, brush, wire mesh and all accessories required for under water cleaning of slope area at deep end including diving persons life insurance and any emergencies etc.(c) Cleaning of swimming pool should be carried out minimum once in a week and as and when ordered / directed by Engineer-in-charge / GE as per site requirement by deploying required manpower.(d) Cost of cleaning material and chemicals required for cleaning shall be deemed to be included in the quoted rate(e) After every cleaning the following water quality and standard parameters to be checked and confirmed to the Engineer-in-Charge as per TI 03/2010 and cost of testing equipment shall be deemed to be included in quoted rate:- (i) Ph :7.4 to 7.6 (ii) FRC : 0.5 to 1 PPM (iii) Total Allkanity: 75 ppm minimum (iv) Total Hardness: 200 ppm minimum (v) TDS: 500 ppm minimum(f) Testing equipment such as pH meter, Chlorine test kit, Water Alkalinity test meter, Water Hardness test meter and TDS meter should be made available at Swimming Pool and cost of the same is deemed to be included in quoted rate and nothing extra shall be paid on this account. |
| 5 | Supply and installation of chlorine gas supplied in 900 Kg/100 kg cylinders for water treatment at Swimming Pool / Water Supply installations under the AOR of GE (U-II).Note:(i)Testing of cylinders, repair to outlet valves of cylinders, gas control and regulating system should be checked and ensured for leakproof and proper functioning at each replacement of cylinder and the rate quoted is deemed to be included for the same.(ii)Chlorine gas will be supplied in 900/100 Kg as ordered and directed by Engineer-in-Charge as per site requirement.(iii) All safety equipment\"s/Masks should be providedby the contractor during replacement of chlorine gas cylinder and the quoted rate is deemed to be included for the same. |
| 6 | Supply only copper sulphate required for swimming pool complete all as specified by Engineer-in-Charge. |
| 7 | Supply only Alum crystal required for swimming pool complete all as specified by Engineer-in-Charge. |
| 8 | Supply and deliver Calcium Hypochlorite granules containing 65%–70% available chlorine by mass, packed in 40–45 kg drums, suitable for disinfection of drinking water. The material shall be free-flowing, free from foreign matter, and shall not introduce toxic or undesirable substances in treated and disinfected water beyond the acceptable limits prescribed in IS:10500 (2012). Each consignment shall be accompanied by a manufacturer’s Certificate of Analysis, batch number, date of manufacture, and proper labelling on drums indicating product details, net weight, and safety instructions complete all as specified by Engineer-in-Charge. |
| 9 | Supply only Heavy Duty Nylon brush suitable for using in existing make and model suction sweeping pump set at SVN colony swimming pool complete all as specified by Engineer-in-Charge. |
| 10 | Testing of water samples as per IS:10500 (Amended up to date) from any NABL approved / Govt laboratorytested for its parameters such as physical, chemical, and biological characteristics by collecting water samples from various Swimming Pools / water supply installations under the AoR of AGE E/M No. I (U-II). Original Test reports shall be submitted to Engineer-in-Charge. Note: Water testing shall be carried out once in month and / or as directed by Engineer-in-Charge. |
| 11 | Supply only self reinforced PVC 50mm dia suction hose in suction sweeper pump for Swimming pool complete all as specified and directed by Engineer-in-Charge. |
| 12 | Material and labour for overhauling of suction sweeping pump set of 3 HP to 5 HP capacity by disconnecting/ dismantling and replacement of unserviceable worn out bearings, renewal of worn out parts like shaft sleeves, oil seal / gland rope, rubber packing / coupling, greasing and connecting up and testing complete all as directed by Engineer-in-charge. |
| 13 | Dismantling or removing of suction sweeping pump set of any make and model, of capacity3 HP to 5 HP from its installed position by disconnecting suction and delivery lines, disconnecting electrical cables, dismounting the pump and motor from trolley mounted platform, shifting to workshop, cutting and removing burnt out winding and rewinding with super enamelled copper winding wire of existing gauge and number of turns including necessary insulation, varnishing, heating etc and bringing back, reinstalling on existing trolley mounted platform and testing for satisfactory performance complete all as directedby Engineer-in-Charge. |
| 14 | Material and labour for repair of trolly ofsuction sweeping pump of 3 to 5 HP capacity by removing pump set from trolly mounted platformand replacement of unserviceable wheels, replacing of corroded platform of MS/angles etc with required welding etc and connecting and reassembling complete all as directed by Engineer-in-Charge. |
| 15 | Material and labour for cleaning of UG sump/ balancing tank at Command Swimming Pool of capacity 1,00,000 Liters by pumping out the accumulated water in the bottom and removing the complete silt from the sump and depositing at a distance of 50m away from the tankand levelling as directed and cleaning with bleaching powder and wire brushing the sump after scrapping the walls and bottoms of the sump completely without disturbing the filtration process to swimming pool including applying one coat of white wash internally and painting the sump with cement base paint on external surfaces and lettering the sump capacity, date of cleaning and due date of cleaning on the sump wall complete all as specified and directed by Engineer-in-Charge. |
| 16 | All as per item No. 13 here-in-before but UG sump/ balancing tank at SVN Colony Swimming Pool of capacity 50,000 Liters |
| 17 | Supply and fixing in replacement of following spare parts for gravity feed type gaseous chlorination plant complete all as specified and as directed by Engineer-in-Charge:- |
| 18 | Copper pipe with brass nut & nipple to connect the chlorine tonner and chlorination plant |
| 19 | PVC Primary Filter |
| 20 | Diaphragm type pressure gauge |
| 21 | PVC moisture nut |
| 22 | Moisture glass tube |
| 23 | Brass Chlorine control valve |
| 24 | PVC gas bend |
| 25 | PVC Secondary filter |
| 26 | PVC NRV bend |
| 27 | Mixing Chamber made from 90mm dia chemically treated PVC pipe with 75mm dia borosilicate glass tube, glass orifice tube, rubber\"O\" ring & rubber bush complete |
| 28 | PVC Tee with diaphragm valve |
| 29 | PVC water bend |
| 30 | PVC solutionizer |
| 31 | Outlet connection |
| 32 | Flow meter |
| 33 | Supplying and fixing in replacement of CPVC pipes of size 32mm(OD) SDR 11 along with Plain CPVC SDR 11 fittings and fixing solvent in trenches / fixed to walls with suitable CPVC pipe clamps / laid on floors etc complete all as specified and directed by Engineer-in-Charge. |
| 34 | Supply and fix CPVC Union suitable for 32mm (OD) CPVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 35 | Supply and fix CPVC Ball Valve suitable for 32mm (OD) CPVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 36 | Supply and fix CPVC Female Brass Threaded Adaptor (FTA/ FBTA) suitable for 32mm (OD) CPVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 37 | Supply and fix CPVC Male Brass Threaded Adaptor (MTA/ MBTA) suitable for 32mm (OD) CPVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply and fix CPVC Brass Tee suitable for 32mm (OD) CPVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 39 | Supply and fix CPVC Brass Elbow suitable for 32mm (OD) CPVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 40 | Material and labour for Framed work with Fe 410 -W (Gde E- 250) quality A as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing including painting with two coats of synthetic enamel paint of approved colour over a coat of red oxide primer complete all as specified and directed. |
| 41 | Material and labour for cleaning of swimming pool of capacity 31.50 Lakh Liters at Command Swimming Pool by pumping out the accumulated water in the bottom, removing complete silt, applying tile cleaning acid and scrapping the side wall tiles and bottom tiles for scale free surfaces and cleaning with fresh water complete all as specified and directed by Engineer-in-Charge. |
| 42 | All as per item No. 24.00 here-in-before but of capacity 8.40 Lakh Liters at SVN Colony Swimming Pool |
| 43 | Supply and replace Cast Iron sluice valve of size 300mm dia bore, having pressure rating PN 1.6, double flanged,non-rising stainless steel spindle with iron wheel conforming to IS:14846-2000with jointing material i.e. new rubber gasket, GI nuts, bolts & washers etc of suitable size including taking down existing old unserviceable sluice valve complete all as specified and directed by Engineer-in-Charge. |
| 44 | All as per item No. 26.00 here-in-before but of size 250mm dia bore. |
| 45 | All as per item No. 26.00 here-in-before but of size 200mm dia bore. |
| 46 | All as per item No. 26.00 here-in-before but of size 150mm dia bore. |
| 47 | Supply and replace Cast Iron Non Return Valve (NRV) 150mm NB with flanged ends swing type / ball type as per site requirement, including replacement of necessary packing material, GI bolts, nuts and washers etc including taking out existing unserviceable NRV of any description complete all as specified and directed by Engineer-in-Charge. |
| 48 | Supply and replace Cast Iron foot valve of size 200 mm NB, flanged end ball type/ swing type including replacement of necessary packing material, GI bolts, nuts and washers etc including taking out existing unserviceable foot valve of any description complete all as specified and directed by Engineer-in-Charge. |
| 49 | Supply and fixing in replacement of 100 mm dia Stainless Steel (SS) casing Burdon tube type pressure gauge 0-10 Kg/CM2including taking out of existing unserviceable gauge of any description complete all as specified and directed. |
| 50 | Material and labour for M.S. Black Pipe plain end as per IS:1239 (I), nominal bore 250 mm dia, medium class with all fittings including cutting, welding and joining etc as per site requirement and applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer including taking up / down of existing unserviceable pipe of any description complete all as specified and directed. |
| 51 | All as per item No. 33.00 here-in-before but of nominal bore 200 mm dia |
| 52 | All as per item No. 33.00 here-in-before but of nominal bore 150 mm dia |
| 53 | Supply only MS slip-on weldable flange suitable for 250 mm NB pipe, complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply only MS slip-on weldable flange suitable for 200 mm NB pipe, complete all as specified and directed by Engineer-in-Charge. |
| 55 | Supply only MS slip-on weldable flange suitable for 150 mm NB Pipe, complete all as specified and directed by Engineer-in-Charge. |
| 56 | Supply only flange joint with rubber or fibre board gasket including suitable bolts, nuts and washers for 250 mm NB pipe, complete all as specified and directed by Engineer-in-Charge. |
| 57 | Supply only flange joint with rubber or fibre board gasket including suitable bolts, nuts and washers for 200 mm NB pipe, complete all as specified and directed by Engineer-in-Charge. |
| 58 | Supply only flange joint with rubber or fibre board gasket including suitable bolts, nuts and washers for 150 mm NB pipe, complete all as specified and directed by Engineer-in-Charge. |
| 59 | Supply and fix in replacement of CI Butterfly valve of size 200mm nominal bore as per IS 13095, PN 16, wafer type without lugs, suitable for clamping between flanges as per ANSI B 16.1 CI-125, including flanges, fittings, gasket, nuts, bolts, washers etc. including taking up / down of existing unserviceable butterfly valve of any description complete all as specified and directed. |
| 60 | All as per item No. 42.00 here-in-before but of size 150mm nominal bore. |
| 61 | Material and labour for preparation of old painted surfaces of fresh water pump sets of capacity 3 HP to 5 HP and painting to electric pump/air blower/compressor and motor set and base frame with two coats of synthetic enamelled spray paint of approved colour as per standard MES colour coding complete all as specified and directed by Engineer-in-Charge. |
| 62 | All as per item No. 44.00 here-in-before but of capacity 12.5 HP to 15 HP |
| 63 | All as per item No. 44.00 here-in-before but of capacity 20 HP to 25 HP |
| 64 | Material and labour for preparing new or previously untreated steel surfaces of water pipe lines of any size / Pressure sand filter / Activated Carbon Filter / Electric Panels any position / MS plates / grills etc,with two coats of synthetic enamelled paint over one coat of red oxide primer with & including marking direction of flow & name of feeder etc, complete all as directed by Engineer-in-Charge. |
| 65 | M & L for Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high complete all as specified and directed by Engineer-in-Charge |
| 66 | M & L for Index hands (natural size) or arrows (upto 40cm long), complete all as specified and directed by Engineer-in-Charge. |
| 67 | M & L for writing Stops, commas, short lines, dashes, hyphens, brackets, etc, complete all as specified and directed by Engineer-in-Charge. |
| 68 | Material and labour for Surface dressing not exc 15cm deep in any type of soil and site clearance including cutting and removing of plants/bushes, levelling of surface area, throw wastage material out of fencing area/ compound wall up to 50m distance at sub station areas / pump House areas complete all as specified and as directed by Engineer-in-Charge. |
| 69 | Material and labour for Supply, installation and testing of LED flex Glow Sign Board for front lit office / installation boards prints stretched on a metal frame, where the sun or the ambient light lends visibility to the board complete comprising of the following components with below given detailed specifications including taking down of existing unserviceable office / installation sign board of any description:-(i) Metal Frame / Box: The base structure of board should be made of a metal frame in the form of a box of 6 – 8 inches deep and the width and the height and shape of the frame are as per site requirement and as directed by Engineer-in-Charge by using 0.5 – 0.75 inch thick, metal pipes to fabricate the box.(ii) Tin Sheet / Patra: The above box should be wrapped by a tin sheet or ‘patra’ on the back and the sides in a standard black or white colour as directed by Engineer-in-Charge.(iii) LED tubes as a Source of Light: LED tubes as the source of light for GSB, fitted inside the box. Qty of LED tubes shall be as per the manufacturers recommendations based on the size of GSB decided by Engineer-in-Charge. Make of LED tubes : Havells / Bajaj / Crompton / Wipro / Philips(iv) Brackets to Hold the Board in Place: Completed board shall be fitted on wall / metal structure with suitable shaped brackets, nuts, bolts and washers etc and GI wires as per site requirement and as directed by Engineer-in-Charge. |
| 70 | (Item No 52.00 Contd--)(v) Printed Star Flex: The office / installation board design / art work shall be as per sample given by GE / Engineer-in-Charge printed on a specialised media known as Backlit Star Flex 350 GSM with UV ink prints / Eco Solvent ink prints layered in a double strike. This print should has the following characteristics:- Flex is a printable roll of plastic with a cloth like weave on the back. The front surface should specially coated to receive inkjet inks. Print should be waterproof, scratch-resistant and fade-resistant. The denier or the weave on the back lends strength to the print. The weave and printable top layer of backlit flex should be translucent. It should allow light to pass through and when this happens, the print on top gets a very beautiful glow. ‘Star’ is a premium brand of flex. Prints on Star flex have a very high resolution extremely vibrant colours.Note: (a) The size, dimensions and shape of varying dimensions shall be as per site requirement and as specified and directed by GE / Engineer-in-Charge. (b) The measurement of the completed board shall be measured in square feet on the front face only and hence the quoted rate shall deemed to be included for the depth of the board i.e. 6 to 8 inches. (c) The quoted rate shall be inclusive of cost of transportation to site and installation at any height / in any position and the fixing brackets and accessories and dismantling of existing unserviceable sign board of any description complete all as specified and directed by Engineer-in-Charge. |
| 71 | Material and labour forsun boards or foam boards for offices / installations made of 3mm-thick foam with a smooth matte printing surface in customisable design templates in any size and shape and printing the details as provided/directed by Engineer-in-Charge.The printing shall be done using digital technology that should give the sun board a sharp and professional look. The Vinyl sun boards should have a stiff property with good protection against direct sunlight to avoid colour fading & cracking, resulting in good shelf life. Note:(a) The quoted rate shall deemed to be inclusive of transportation to site and fixing with suitable fixing accessories complete all as specified and directed by Engineer-in-Charge. (b) The measurement of the completed board shall be measured in square feet.(c) Quoted rate shall be inclusive of custom printing charges. (d) Quoted rate shall deemed to be inclusive of dismantling and taking down of existing unserviceable sign boards of any description. |
| 72 | Supply and fixing in replacement of LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamps complete all as specified and directed by Engineer-in-Charge. |
| 73 | Supply and connect in replacement of PVC insulated and PVC Round Sheathed, Copper Conductor (flexible) industrial cable, 1100 Volts grade, conforming to IS 694, three core, 1.5 sqmm for connecting from junction box to street light fitting complete all as specified and directed by Engineer-in-Charge. |
| 74 | SCHEDULE OF CREDITNote :- Amount of Rs. 44,440.00 indicated in Tender Documents as Schedule of Credit shall be deducted from the total quoted amount of BOQ. |
