|
| 1 | Demoliton of cement concrete including tiles and mortar of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 2 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 3 | M&L for special treatment of sunken portion of WCs and Bath room as per following stages:Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc.Stage 2:- Providing10mm thick plaster in CM 1:4 with water proofing compound of approved make.Stage 3:-Applying any water proofing compound of approved make(and allow to dry for 8 hours) under touch dry condition.Stage 4:-Applyingtwo coats of water proofing decorative elastomeric coating system ofany water proofing compound of approved make(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufactutrer instruction.Stage 5:-Again rendering 10mm thick in CM 1:4 mixed with any water proofing compound of approved make.Stage 6.All CI joints shall filled with mixture of cement fine sand and plaster seal any water proofing compound of approved make.Stage 7:-Making holes in wall and fixing600mm long 20mm dia GI spout for draining the surplus water if any. |
| 4 | M&L for joint freeVirified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in floors etc colour as approved set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:4) all as specified. |
| 5 | M&L for ceramic tiles edge to edge joint 7 to 8 mm thick area of each tiles exc 0.11 Sqmbut n exc 0.18 sqm onvertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match with floortiles including 10 mm thick backing plaster in CM (1:4) as specified and directed. |
| 6 | M&L for Coloured Non-skid/matt finish Ceramic tiles 7 to 8 mm thick exc. 0.06 sqm but n.exc 0.11sqmarea of each tiles in floor/ steps etc set and jointed in neat cement slurry and pointed in coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed. |
| 7 | M&L for Glazed Ceramic tiles 450x300x 8-10 mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing in cement mortar (1:3) all as specified and directed. |
| 8 | M&L Granite (of any type)16 to 20 mm thick machine cut fixed onslab,window cill etc , bedded & jointed with grey cement slurry & pointed with white cement with admixure of pigment to match the shade of granite stone including cutting, moulding & polishing over and including20 mm thick screed in CM (1:4) all as directed by Engr in charge |
| 9 | M & L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as directed by Engr in Charge. |
| 10 | Demolition of precast concrete block walling built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed. |
| 11 | M&L precast cement concrete block masonry with solid block, exc 10cm in width in PCCtype C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) complete all as specified and as directed. |
| 12 | Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 13 | M & L for rendering to concrete or block masonry surfaces or surfaces other than fair faces of brick surfaces, 10mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cementcomplete all as specified and as directed. |
| 14 | M & L rendering 5mm thick in CM (1:3) on ceiling surfaces finished even & smooth without using extra cement complete all as specified and as directed. |
| 15 | M & L for rendering 5 mm thick in cement mortar 1:4 over a backing coat of 10mm thick in CM 1:6 (Total 15 mm thick) on concrete or brick masonry surfaces including mixing water proofing compound as per manufacurers instructions and finishing the top surface even and fair complete all as specified and as directed.Note: Water proofing compoundwill be measured and paid separately. |
| 16 | M & L rendering 5mm thick in CM (1:3) on ceiling (external) surfaces finished even & smooth without using extra cement complete all as specified and as directed. Note: Water proofing compoundwill be measured and paid separately. |
| 17 | Supply only Integral water proofing compound all as directed. |
| 18 | Material and labour for complete removal and applying one coat of white cementitious putty on wall and making the surfaces smooth by rubbing with sand paper to achieve finished surface complete all as specified and as directed. |
| 19 | M&L preparing newly plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat ofprimer all as specified & directed |
| 20 | M&L preparing newly plastered surfaces of ceiling and applying two coats of oil emulsion distemper over a coat ofprimer all as specified & directed |
| 21 | M & Lexisting treatment on wall & finishing the surface & appliying two coat of oil bound distemper along with primer all as specified |
| 22 | M & L for complete removel of existing treatment on ceiling and applying two coats of oil emulsion distemper over a coatof primer all as specified & directed |
| 23 | M & L for preparation of old surfaces and applying one coat of 100% Premium acrylic emulsion painthaving VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal esistance, dirt resistance exterior paint of WHITE COLOUR with silicon additives coat applied @ 1.67 ltr/10 sqm over complete all as specified and as directed by Engineer-in-charge.Make: Asian Paints (Apex Ultima), Berger (Weathercoat Long Life Flexo) Nerolac (Excel Total). Shalimar Paints (Weatherpro+ Super Luxury Emulsion). |
| 24 | Taking up or down20 mm bore tubingand connections and removing off the site all as specified and as directed. |
| 25 | Taking up or down25 mm bore tubingand connections and removing off the site all as specified and as directed. |
| 26 | Supply and laying of CPVCpipes20 mm dia outer boreSDR 11 &plain CPVC SDR 11with all special fittings onwalls /ceilings or laying in floors complete all as specified and as directed. |
| 27 | Supply and laying of CPVCpipes25mm dia outer boreSDR 11 &plain CPVC SDR 11 with all special fittings onwalls /ceilings or laying in floors complete all as specified and as directed. |
| 28 | Supply and fixing 20 mm outer dia CPVC Male Brass Threaded Adaptor (MTA/MBTA) all as directed. |
| 29 | Supply and fixing 25 mm outer dia CPVC Male Brass Threaded Adaptor (MTA/MBTA) all as directed. |
| 30 | Supply and fixing 20mm outer dia CPVC pipes brass Elbow (3/4 X1/2) all as directed. |
| 31 | Supply and fixing 20mm outer dia CPVC female brass adaptor (FTA/FBTA) all as directed. |
| 32 | Supply and fixing 25 mm outer dia CPVC female brass adaptor (FTA/FBTA) all as directed. |
| 33 | Supply and fixing 20 mm outer dia CPVC Brass Tee |
| 34 | S&F in repair25 mm cpvc ball valve / Gate valvescrewed both ends for cpvcpipe complete all as specified and as directed. |
| 35 | Dismantling of plain or corrugated steel sheeting any gauge thickness or similar pattern roof coverings all as directed. |
| 36 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as manufacturers instruction and as directed. |
| 37 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws asin ridges, hips, valley gutter, drip, and straight flashing complete all as specified and as directed. |
| 38 | Dismantling wrought iron or mild steel work of any description not other wise provided for complete all as specified and as directed. |
| 39 | M&L Roof trusses (framed), trusssed, purlings, crane gantries, rails and fasternings and heavy breacket frasming(Beam,tee,angle,Channel, hollow sec or flat sections) including distance pieces, cleates etc. complete all as specified and as directed. |
| 40 | S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410 W (Grade E-250) quality A complete all as specified and as directed. |
| 41 | M & L for providing cement concrete type B1 (1:2:4) using 20 mm graded aggregate as in copings,apex stones,bed plates etccomplete all as specified and as directed |
| 42 | Preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 43 | S&F Framed work such as grills, gratings,etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165complete all as specified and as directed. |
| 44 | Dismantling of ceiling boarding in description fixed in any position with nails complete all as specified and as directed. |
| 45 | S&F aluminium flatas wind tie fixed with 50mm/75mm aluminium self tapping screws complete all as specified and as directed. |
| 46 | S & F in repairs anodized aluminium grid work 605 x 605 mm with using 36.5mmx23.5mmx1.5mm thick main tee, 23.5 x23.5mmx1.28mm cross tee and 25x25x1.5mm angles fixed to perimeter of wall for false ceiling including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified & directed all as specified & directed |
| 47 | M&L 4mm thick Non asbestos fibre cement building boards fixed or laid / inserted to timber/ GI / Aluminium framework with screws all as directed. |
| 48 | Preparation of old wooden surfaces exc. 10cm width and girth and applying one coat of synthetic enamel paint, all as specified. |
| 49 | Preparation of old steel surfaces exc. 10cm width and girth and applying one coat of synthetic enamel paint, all as specified. |
| 50 | Taking down chowkats or framesnot exceeding 1.5 Sqm (with shutters & grill (if fixed) without taking off shutters from the frame) complete all as specified and as directed. |
| 51 | Taking down chowkats or frames exc 1.5 Sqm and not exceeding 4 Sqm (with shutters and grill (if fixed) without taking off shutters from the frame) complete all as specified and as directed. |
| 52 | S & F Solid PVC Door frame of size 50mm x 47mm made out of 5mmrudraksh colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing all as directed. |
| 53 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling ofrudraksh colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed. |
| 54 | S&F Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. |
| 55 | S & F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed. |
| 56 | S & F only 4 mm Plain sheet glass ordinary quality, in squareexc 0.5 sqm each all as directed. |
| 57 | S & F only Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including taking down all as specified and as directed. |
| 58 | S & F onlyFigured glass 4mm,pin head type and glazing with oil putty in squares n exc 0.5 sqm in each pane all asdirected. |
| 59 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 60 | S&F for Factory made double extruded WPC (Wood Polymer Composite) solid door & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length etc., complete all as specified and as directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 61 | S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed. (Note: stainless steel butt hinges and necessary S S screws incl in this item) |
| 62 | S & F second class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc divided in to squares with plain, chamfered or rounded, mitred and rebated sash bars fitted with cut and mitred beads for securing glass etc complete all as specified and as directed. |
| 63 | S&F Aluminium anodised sliding door bolts 300mm long with hasp and staple all as directed. |
| 64 | S&F aluminium anodised barrel tower bolt of extruded section 150mm long all as directed. |
| 65 | S&F extruded aluminium alloy handle fabricated type anodised 100mm long all as directed. |
| 66 | S&F extruded aluminium alloy handle fabricated type anodised 150mm long all as directed. |
| 67 | S & F butt hinges of stainless steel 150 mm long ISI marked fixed with brass screws all as directed. |
| 68 | S & F butt hinges of stainless steel 100 mm long ISI marked fixed with brass screws all as directed. |
| 69 | S & F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor all as directed. |
| 70 | S&F for factory made single extruded 18/19 mm thick WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed.NOTE:- All joint should be filled with sealant |
| 71 | S & F in repair curtain Rod, stainless steel,chromium plated 25 mm dia withstops, rollers etc complete all as specified and as directed. |
| 72 | S & F in repair brassbracketschromium plated suitable for curtain Rod 25 mm dia complete all as specified and as directed. |
| 73 | S & F Stainless Steel plate rack of size 910 mm X 960 mm of super deluxe model, suitable for 12 plates made with 22 gauge sheet and weight not less than 5.5 Kg, completeall as specified and as directed. |
| 74 | S&F in repair stainless steel sink with drainage board made out of 1.00 mm thick sheet with plug, washers, Ms angle cantilever brackets for suitable size and connecting union to pipe of overall size 1140 mm x 500 mm and bowl size 510mm x 400 mm x 190 mm all as directed. |
| 75 | S&F Wash basins including brackets, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe all as directed. |
| 76 | S & F 32 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as directed. |
| 77 | S & F 40 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as directed. |
| 78 | S & F 32 mm dia of discharge pipe, Waste coupling of PTMT half or full threaded, minimum weight 32mm- 45gms/40mm-60 gms all as directed. |
| 79 | S & F 40 mm dia of discharge pipe, Waste coupling of PTMT half or full threaded, minimum weight 32mm- 45gms/40mm-60 gms all as directed. |
| 80 | S & F in repair Bib Taps with flange, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and as directed. |
| 81 | S&Fin repairs stop valvescast copper alloy chromium platedwith long shank and cupfancy type screwed down high pressurescrewed both ends for pipe or union fixed for 15mm bore,includingnecessary cuttingand making good wall or floor tiling to match existing(tilesto be paid supplied only rates) etc complete all as specified and as directed. |
| 82 | S&Fin repairs stop valvescast copper alloy chromium platedwith long shank and cupfancy type concealed screwed down high pressurescrewed both ends for pipe or union fixed for 15mm bore, includingnecessary cuttingand making good wall or floor tiling to match existing etc complete all as specified and as directed. |
| 83 | S & F Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and as directed. |
| 84 | S & FBib Taps, long boby with flangecast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and as directed. |
| 85 | S&Fbrass chromium plated telescopic Hand shower (Health Faucet) (ABS Body) with 1 Meter long Easy Flex Tube in Chrome Finish& wall Hook all as directed. |
| 86 | S&Fbrass chromium plated shower rose with 150mm longCP shower arm 125 mm size revolving type suitable for 15 mm bore pipes complete all as specified and as directed. |
| 87 | S & FSoap Dish,brass chromium platedof approximate size 160 x 160 x 90 mm with screws complete all as specified and as directed. |
| 88 | S & FPVC Body Cabinet Box Mirror of size 350mm X 450mm X 100mm in PTMT alloy of approved design and pattern complete all as specified and directed |
| 89 | S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long of approved quality complete all as specified and as directed. |
| 90 | S & F in repairs Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressurewith long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed. |
| 91 | S&F in repairs Vitreous China wash down watercloset pan (pedestal pattern), white including Plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as directed. |
| 92 | S & F in repairs 10 Liters capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of lowor high density of PVC, 32mm diaincluding brackets and connections to pipe of Make Slimline or Cera or equivalent make complete all as specified and as directed. |
| 93 | S&Fin repairs PVC flexible connection with PTMT nuts, of 15mm dia and 600mm long with brass unions and rubber washers on either side, for connecting water supply line to WHB, flushtank ,Geyser etc, all as specified. |
| 94 | Demolition and breaking up drain pipes of size 75/100 mm dia (Salt glazed ware, AC or Reinforced concrete, PVC (SWR)) set in cement mortar complete all as specified and as directed. |
| 95 | S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as indown pipes complete all as specified and as directed. |
| 96 | S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 97 | S & F 75 in repairsmm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed. |
| 98 | S & Fin repairs 75 mm bore PVC [SWR] Junction Single [Single \"T\"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. |
| 99 | S&F in repair PVC (SWR)bendswith access door 75mm dia complete all as specified and as directed. |
| 100 | S & F in repairs 75mm dia out let, PVC (SWR) Floor Trap with SS grating including jointing to waste pipe fixed with solvent cement complete all as specified and as directed. |
| 101 | S & F in repairs Brass Chromium Plated Tubular Towel Rail, 20mm dia,D Type, 600 mm long between flanges complete all as specified and as directed. |
| 102 | Cutting holes exc. half brick but not exc one brick in brick walls built in CM or cement lime mortar & stone walls built in lime mortar for inserting holdfasts & making good dismantled portion in CM (1:3) or PCC (1:2:4) Type B-1 as required complete all as specified and as directed. |
| 103 | S & F of 8 feet (with four pipes) pulley operatedclothes drying system consisting of anodized aluminium pipes , each of outer dia 22 mm and inner dia 19.80 mm pulleysmade up odf derlin with rope guide mounted on channelpair of length 24\"\" (distance between two pipes is adjustable ) locking system to hide rope knot channel to be mounted or fixed with self tapping screws providedin kot . Rope will be polyster braided undryed of 3.5 +- 0.50mm dia all as directed. |
| 104 | Taking down carefully existing aluminium point wiring (light, fan , socket or power) complete fittings fixture such as switches Ceiling roses, pendents,regulators, sockets etc to be measured separately)unscrewing from Board/outlet boxes, fittings & fixtures such as switches, sockets, ceiling rose lamp holder tube/ceiling fitting, bulk head fittings, tube lights & regulator etc and making good disturbed surfaces of walls, floors etc. complete all as specified and as directed. |
| 105 | M&L for taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified and as directed. |
| 106 | M&L for taking down carefully existing old DBs and making good disturbed surfaces of walls to match the existing surfaces complete all as specified and as directed |
| 107 | M&L for point wiring (modular type) with two run of PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm (FRLSH), PVC conduit medium grade/ PVC casing caping and pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc)and drawing one run of 1.5 sqmm PVC insulated unsheathed multistranded copper conductor cable (FRLSH) as earth continuity wire in green colour connected to common earth and each terminal box/fitting all as specified and as directed by Engr-in-Charge.(In ceiling Portion surface conduit wiring shall be carried out.) Note: The quoted rate inclusive for the following :- (a) GI metal flush box and Modular cover plate with frame of any module complete.(b) Proper colour coding is to be followed as per IS Specification. (c) wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement.(d) Cutting chases/making good disturbed surfaces of wallfor fixing concealed conduit shall be deemed to be included in quoted rate. |
| 108 | One light point controlled by one one way switch. |
| 109 | One ceiling fan/exhaust fan point controlled by one switch. |
| 110 | One 3 pin socket outlet 5 Amps independent. |
| 111 | One 3 pin socket outlet 5 Amps on the same board with other switches |
| 112 | One bell/ buzzer point controlled by one push button independent |
| 113 | All as per item No 107 above but cable with 4.0 sqmm for socket outlet 15 amps independent/Earth plug and socket |
| 114 | M & L for submain wiring with two single core PVC insulated unsheathed multistranded copper conductor cable of size 6 sqmm (FRLSH) and one single core PVC insulated unsheathed multistranded copper conductor cable green colour of size 6 Sqmm (FRLSH) as earth lead in and including concealed with PVC conduit medium grade of suitable size or surface wiring with PVC casing caping of suitable size and making good the disturbed wall surfaces to match with existing specification including takind down unserviceable submain wiring complete all as specified and as directed.Note : (i) Three run of cable with one run of PVC conduit/PVC casing and caping will be measured as one length.(ii) Wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement.(iii) Cutting chases/making good disturbed surfaces of wallfor fixing concealed conduit shall be deemed to be included in quoted rate. |
| 115 | S&F modular switch one way 6 Amps, 1 module complete all as specified and as directed |
| 116 | S&F modular socket, 2/3 pin 6 amps, 2 module complete all as specified and as directed. |
| 117 | S&F modular switch one way 16 Amps, 1 module complete all as specified and as directed. |
| 118 | S&F modular socket, 2/3 pin 6/16 amps, 2 module complete all as specified and as directed. |
| 119 | S&F modular bell push 6 Amps, 1 module complete all as specified and as directed. |
| 120 | Supply & fixing Bell, Ding Dong AC. 230 volts, single polecomplete all as specified and directed. |
| 121 | Supply & fixing ceiling Rose, 3 terminal polycarbonate isolated body complete all as specified and as directed. |
| 122 | S&F LED lights fitting 20W, >120lm/watt, CCT value 4000K to 6500K, surge protection of 2 KV, 4 feet 220V, AC IP-20, aluminium housing with inbuilt driver including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 123 | S&F as in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt, 120lm/watt, CCT value 4000K to 6500K, 220 V AC decorative type with inbuilt driver including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 124 | S&F as in repair metallic exhaust fan of size 300 mm with louvre, 230V, RPM 1400, metal body including taking down old unserviceable exhaust fan and deposited to MES store yard complete all as specified and as directed. |
| 125 | Supply & fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 HZ, RPM 1200, Copper winding of sweep 250mm and exhaust fan shall be fixed with suitable size of buzzer bolt/hold fastner including making hole to the wall surface of any type/girth and at any height for fixing of exhaust fan including making good disturbed surface with existing wall colour and provision of cable from ceiling rose/connector to fan complete all as specified and as directed.Note :- Old unservicable exhaust fan will be deposited to MES store yard. |
| 126 | Supply & fixing BLDC ceiling fan 1200mm sweep with anti corrosive aluminium blades, suitable electronic remote as per OEM design, down rods and connected accessories, 230 V, 1200 mm sweep. 350 RPM, Min air delivery 220 CFM, 5 star rated, equipped with brushless direct current motor (BLDC) of wattage < 28W, motor warranty not less than 5 years including provision of cable from ceiling rose/connector to fan complete all as specified and as directed. Note :- Old unservicable ceiling fan will be deposited to MES store yard. |
| 127 | Supply & fixing electric water heater, storage type, electro plated steel body as per OEM design with element free induction heat transfer technology through induction coil capacity 25 Ltr, BEE 5 star with reduction heating time 10-12 minutes and with digital temperature display, live lemperature with smart mode, automactic operation of water heater for ON and OFF time complete with all accessories such as safety valve, thermostat, NRV, connection piece fastner bolts including stainless steel hose pipe including taking down unserviceable water heater/geyser and desposit to MES store yard complete all as specified and as directed. |
| 128 | Supply & fixing Single pole and neutral enclosure with a two pin and earth plug and socket suitable for RCBO 2 pole, 20 to 40 amps rated complete all as specified and as directed.Note : RCBO will be measured and paid separately. |
| 129 | Supply & fixing MCB DB\"s SPN 12 way, IP-54, IK-09 double door, sheet metal enclosure, 240V, suitable rated busbarincluding suitable size of copper lugs for fixing of cable and taking down unserviceable DB complete all as specified and as directed.Note : The cost for flushing of Distribution box in any type of wall and making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate |
| 130 | S&F Surge Protection Device, breaking capacity 40KA/Pole, 4 Pole with sheet metal enclosure complete all as specified and as directed. |
| 131 | S&F RCBO 25 Amps, double pole 240V, AC type, 30 mA with sheet metal enclosure complete all as specified and as directed. |
| 132 | Supply and fixing MCB SP 6-32 Amps ,10 KA, C Curve, 230 Volts ,50 HZ complete all as specified and as directed. |
| 133 | M&L for taking down unserviceable aluminium earthing strip any size complete all as specified and as directed. |
| 134 | M&L for re-fixing of aluminium earth continuity conductor of size 25x3mm fixed to wall from ground level to upto fourth floor/roof top of the fourth floor for lightening arrester using porcelain clit/post insulators with screw/self drill GI screw with rubber washer complete all as specified and as directedNote : Necessary scaffolding work for fixing of earth continuity conductor shall be deemed to be included in the quoted rate. |
| 135 | Supply and fixing as in repair aluminium earth continuity conductor of size 25x3mm fixed to wall from ground level to upto fourth floor/roof top of the fourth floor for lightening arrester using porcelain clit/post insulators with screw/self drill GI screw with rubber washer complete all as specified and as directedNote : Necessary scaffolding work for fixing of earth continuity conductor shall be deemed to be included in the quoted rate. |
| 136 | M&L for taking down old post insulator and S&F post insulator for earthing strip from ground level to upto fourth floor wall/roof top of the fourth floor complete all as specified and as directed |
| 137 | M&L for earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised earth strip 25x4mmconnected by means of bolts, nuts, check nuts and washer of galvanised iron or steel, provision of 40 mm dia GI pipe medium grade for protection of GI earth strip and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type C1 chamber, MS funnel, wire gauge, 50 mm thick RCC 1:2:4, type B1earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I.Note: (i) Cost of GI earth strip and GI protection pipe upto 7.5mtr length shall be deemed to be included in the rate quoted for this item(ii) The unit rate shall also includes for Wire mesh, funnel, excavation, PCC chamber pit and test point complete.(iii) Cost of PVC insulated unsheathed copper cable of size 10 sqmm with suitable size of PVC conduit from test point to incomer DB of bldg shall be deemed to be included in the rate quoted for this item. |
