|
| 1 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. |
| 3 | All kinds of soil |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 6 | 1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing : |
| 8 | 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 10 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 11 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 12 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 13 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) |
| 14 | 250x16 mm |
| 15 | 12 mm cement plaster of mix : |
| 16 | 1:6 (1 cement: 6 coarse sand) |
| 17 | 15 mm cement plaster on rough side of single or half brick wall of mix : |
| 18 | 1:6 (1 cement: 6 coarse sand) |
| 19 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 20 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 21 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 22 | One or more coats on old work. |
| 23 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-harge. |
| 24 | With cement mortar 1:4 (1cement: 4 coarse sand). |
| 25 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work |
| 26 | 20 mm nominal outer dia. Pipes. |
| 27 | Providing and fixing PTMT bib cock of approved quality and colour. |
| 28 | 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 29 | Providing and fixing CPVC gate valve/ ball valve (Plastic) of supreme or equivalent make all complete as per direction of Engineer-in-Charge. |
| 30 | 25 mm Dia . Outer Dia |
| 31 | Providing and fixing CPVC Union of Supreme or equivalent make in CPVC pipe including jointing with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. |
| 32 | 25 mm Dia Outer Dia |
| 33 | Arranging welding machine for welding of Broken steel componants such as Handels, fastners, hinges, grills, etc.as and where required as per the direction of Engineer-in-Charge. (rate includes labour & transportation of machine at site). |
| 34 | Refixing of MS gate(Size upto 3.50 Sqm) with existing pillar with required gate hing (heavy type) including making hole, finishing,welding etc all complete as per direction of E-I-C. |
| 35 | Refixing of MS gate(Size upto 2.50 Sqm) with existing pillar with required gate hing (heavy type) including making hole, finishing,welding etc all complete as per direction of E-I-C. |
