|
| 1 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level andremoval of entire debris as ordered outside MD land complete all as directed. |
| 2 | Demolition of cement concrete (un-reinforced) of any description & in any descriptionandremoval of entire debris as ordered outside MD land complete all as directed. |
| 3 | Demolition of unreinforced cement concrete as in roofs, floors (other than ground floors), in any description of beams, staircases, landing, chaj-jas etc including removingof existingAPP membrane any thickness / Screed any thickness etc and removalofentiredebris as ordered outside MD land complete all as directed. |
| 4 | Demolition of brickwork , block masonryor stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris as ordered outside MD land complete all as directed. |
| 5 | Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stackingserviceable tiles at site andremoval of entire debris as ordered outside MD land complete all as directed. |
| 6 | Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site for credit & removal where directed. |
| 7 | Dismantling any type & size of Aluminium Partition or office partitions fixed inany description and stacking aside atsitewhere ordered &refixing the same in existing or other locationas as ordered withnecessaryaluminium screrws , PVC gasket etc afterthe flooring oftiles is laid vide BOQ itemNo 28 here -in- after fixedcompletetothesatisfaction ofEngineer-in-charge. (Note : (i) Quoted rate isdeemed tobe inclusive ofstackingtheremoved partition , provn of minor accesories such as screws , PVCbeadingetc. (ii) Duecareto be taken by Contractor & his working people during dismantling as well stacking without damaging the Partition materials , in case any damaged is occured for fault ofworking people thesameshall be made good as per its original specification without any extracostto Govt.) |
| 8 | M & L for PCC1 :4 : 8 type D2 using 40 mm gradedcrushed stone aggregate as in foundation filling mass concrete complete all as specified and directed |
| 9 | M&L for reinforced cement concrete 1:2:4 type B0 using 12.5m graded crushed stone aggregate in chajjas / slabs withnecessaryform work completeallas directed.Note :- Reinforcementshall be measured and paid for separately. |
| 10 | Forming jambs, etc to openings (to foregoing item), including cutting, toothing and properly bonding intoold work, also facing, jointing and pointing to match existing work in cementmortar 1:4complete allasdirected.. |
| 11 | M&L for Brick work with well burnt best quality locally available bricks, old size bricks, straight or curved on plan to any radius built in any description in cement mortar 1:6 complete all as directed |
| 12 | All same as per itemNo 11 here-in-above but Brick work builtin cement mortar 1:4 -do- |
| 13 | Form work to rough finished surface ofsides andsoffits of suspended slabs such as roof slabs, floor slabs, landings, chajjas and similar work; not exceeding 200mm thick (Horizontal or sloping) |
| 14 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x100 mm single rebate comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made Make : ECHON/Sintex/Rajshree/Navaratan |
| 15 | All sameas per itemNo 14 here-in-abovebut size offrame 45 X 70 mm single rebate -do- |
| 16 | S&F 28-30 mm thick Prelaminated moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on both side with wood grain texturewith density not less than 650Kg/cum.Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fireetardant and having screw holding capacity complete all as specified |
| 17 | S&F Powder coated aluminium Ventilator (partially fixed glazing and Partially louvered glazing) with arrangement for exhaust fan & includethe following:-(i) Aluminium frame section 45x25x1.80mm.(ii) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape.(iii) 4mm thick frosted glass orinary quality (partially fixed glazing and Partially louvered glazing) and fixed with rubber gasket for with glazed shutter etc. |
| 18 | S&F100 mm size butt hinges, heavy weight weight cold rolled mild steel and fixed . |
| 19 | S & F150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed. |
| 20 | S&F 150 mm size extruded aluminium alloy handles (ISI Marked) fabricated type anodisedand fixed. |
| 21 | S&F300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed. |
| 22 | S&F rolled MSframed work as in ladder fabricated as per design as ordered , fixed on walls by means of 12 mm rust proof anchnor fastemersof 90 mm long,welding whereever necessarycompleteall as directed steel conforming to Fe.290.Gde-E-165. (Note:(i) ladder approx 15 Mts longtobe fabricated & errected. (ii) Quoted rate isdeemed tobe inclusive for providing approx 850 Nos 12 mm dia , 90 mm long rust proof fasteners , drilling holesfor insetingMS Round bar step , welding etcthe spacing distance forproviding fastereners shall be intimatedby Engineer-in-charge |
| 23 | S&F 10 mm dia and over TMTbarscut to length bent to shape required cranking including bending , hooking ends etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 24 | All as per serial item No. 23 here-in-before but 6 to 8mm dia -do- |
| 25 | S&F 10 mm dia and overMS round bar cut tosize madetoshape of cage and fixed to ladder be means of welding etc to the entire length of ladder as oderedcomplete all as specified and directed.(Note : Quoted rate is deemed tobe inclusive of welding .(ii) the size & shape of cage shall be as intimated by Engineer-in-charge ). |
| 26 | M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in floor and finished the surface complete all as directed. |
| 27 | M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in floor and finished the surface even & smoothwithout using extracement complete all as directed. |
| 28 | M&L for10 mm thick Vitrified anti static, stairn proof tiles for ESD (Electrostatic Discharge) Flooring tiles of size 600mm X 600mm (Dark shade as approved) with a specified surface electrical resistance, typically below 1 Mega Ohm (conductive) or between 1 Mega Ohm and 1 Giga Ohm (dissipative) ,thetiles should be robust, with a breaking strength of at least 1300 N for thicknesses over 7.5mm, suitable for high-traffic areas. fixed usinga conductive tile adhesive or a suitable cement mortar mix as specified by the tile manufacturer with appropriate adhesive laid over &including 20mm thick screed bed in cement & sand mortar 1:4 , including copper strip/tape in grids as per site requirement, including 3-4mm spacers and epoxy grout filling at joints as per manufacturer recommendation & as specified .(Note: Quoted rate is deemedtobe inclusive adhesive , 20 m thick cement screed etc). |
| 29 | M & L non-skid coloured joint freeceramic tiles 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified. |
| 30 | M&L coloured glazed ceramictilesof size 350x250x7mm / 450x300x7 mm thick, on verticals surfaces, set and jointed in neat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to matchcompleteall directed. (Note for item Nos29 & 30 : i) Quoted rateis deemed to be inclusive of cement screed. ii) Shade / pattern / Colour of tiles shall be got appproved before procurement). |
| 31 | M&L for 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite , laid over andincluding15 mm thick screed bedding in cement mortar 1 : 6 all as specified & directed.(Note: Quoted rateis deemed to be inclusive of cement screed.) |
| 32 | M&L for rendering 15 mm thick in CM 1:4 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified. |
| 33 | M&L preparing old / untreated wall / ceiling surface and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1-2 mm thick white cement based wall care putty as specified complete all as specified.Note : (i) Painting shall be done using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper/ primer should be able to spray in hard to reach areas and penetration of distemper on the surface |
| 34 | M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation ofnew steel surface complete all as directed. |
| 35 | Taking down old rusted / wornout 15 mm bore GI tubing after necessary disconnection & S&F new 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed. |
| 36 | Taking down old rusted / wornout 20 mm bore GI tubing after necessary disconnection & S&F new 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.(Notefor itemNos 35 & 36 : Quoted rate isdeemedtobe inclusive for cutting / chasing ofpipe line in Brick / stone masonry / concrete surface & making good toits existingspecification without any extracosttoGovt.). |
| 37 | S&F in repair 15mm dia cast copper alloyBib taps fancy type ,with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as directed. |
| 38 | S&F in repair 15mm dia cast copper alloy twowayBib taps,with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as directed. |
| 39 | S&F in repairs 15mm bore Stop valve /Angle cock , fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union |
| 40 | S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated,screwed down high pressure, with or without lettered‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes. |
| 41 | S&F in repairs 15mm bore Stop valve /Angle cock , cast copper alloy, fancy type chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union |
| 42 | S&Fin repairhealth faucet ABS body with wall hook and 1.80 metre long SS braided rubber hose pipe and wall hook mounted type complete.Make:Prayag CatNo BEA-40 or equivalent in approved make. |
| 43 | S&F in repairs brass chromium plated shower rose 75 mm dia with CP Arm with swivel joint, any size, including fixing to steel pipe or union.complete all as directed. |
| 44 | S&F in repair stainless steel soap dish as per existing or as ordered fixed with & including Chromium plated brass screws & plastic cleats all as directed. |
| 45 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete all as directed |
| 46 | S&F inrepair 20mm dia , 60 cm long Towel rail brass chromium plated with flanges fixed on wall with PVC rawl plug & cadmium plated brass screws. |
| 47 | S & F in repairs PVC connection 15 mm sizewith PTMT nuts, 450mm long complete all as specified |
| 48 | S & F in repairs Bottle trap of 40mm dia of discharge pipe of PTMT having minimum water seal of25mm .(Minimum weight 40mm-270 gms) complete all as specified and as directed. |
| 49 | S&F 550 mm X 400 mm size white flat backvitreous china wash hand basin including chromium plated pillar tap (Make: CERA Cat No. S1053101/S1053102 6502) capstain head ,down highpressure with or without lettered \"Hot orCold\" with long screwed shanks & fly nutssuitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitablewashers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected. |
| 50 | S&F in repairs vitreous china urinal, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified and as directed. |
| 51 | S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low levelPVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag |
| 52 | S&F in repairs 600mm x 450mm looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick AC building board or commercial plywood including aluminium framing and fixed to PVC rawl plugs with chromium plated brass screws and cup washers complete all as specified.. Make: Gold fish / Atul / Modi / Triveni Glass |
| 53 | M&L for High density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm of 50mm bore with & including all fittings and fixed complete to walls, ceilings or in floors etc including taking out old unserviceable pipe all as specified & directed |
| 54 | Taking down100 mm dia cast iron or reinforced concrete drain pipe laid in any description & S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in excavated trenches complete all as directed.(Note : Quoted rate isdeemedtobe inclusive ofexcavation & earthwork ). |
| 55 | All sameper itemNo 54 here-in above but 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wall . |
| 56 | S & F 110 mm bore, PVC (SWR) bends of any radius withaccess doorcomplete all as specified and directed. |
| 57 | S&F 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed. |
| 58 | S&F 110mm bore PVC (SWR) vent cowl jonting the same with solvent cement complete all as directed. |
| 59 | Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalicconduit (Medium Grade) concealed on surface conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thicklaminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-(a) One light / Fan / bellpoint controlled by one 5 Amps switch one way |
| 60 | (b) One 3 pin socket point 5/6 Amp on independent board |
| 61 | (c) One 3 pin socket point 5/6 Amp on same board with other switches.(to be provide new point as user reqairment) |
| 62 | S&F switch modular type single pole one way 6 Amp , 1 Module , with all accessories complete all as directed. Make: Legrand Cat No. 6755 01 or equivalent in Philips / Crabtree / ABB / Havells |
| 63 | S&F socket outlet multipurpose 2/3 Pin for 6 / 16 Amp modular type with all accessories complete all as directed. Make: Legrand Cat No. 6755 55 or equivalent in Philips / Crabtree / ABB / Havells |
| 64 | S & F Ceiling rose surface bakelite White / Ivory / Urea finish50 mmdiathree terminals including supply and fix PVC square mounting block complete all as specified and directed. |
| 65 | S & Fand connecting up LED 20 watt fitting6500K 4 feet with 120 lumen/watt,aluminum housing extruded in thermal conductive materialwith powder coated in white colour Extruded serration High Optically efficient plastic FR grade material in milky white,Spring Steel Nickel plated,Inj. Moulded engineering plastic Brown in colour Five year written warranty from manufacturerincluding 23/00.0076 size 3 core copper flexible wire fromconnector to ceiling rose/adoptorfixed as per manufacturers instructions and making necessary electricalconnections and testing on completioncomplete all as directed. Crompton cat NoCCS-100-20-65-HL2-DP-NWH or equivalent in Philips/Havells/Wipro ). |
| 66 | S & F and connecting up LED 5 watt fitting6500K 1 feet with 100 lumen/watt,aluminum housing extruded in thermal conductive materialwith powder coated in white colour Extruded serration High Optically efficient plastic FR grade material in milky white,Spring Steel Nickel plated,Inj. Moulded engineering plastic Brown in colour Five year written warranty from manufacturerincluding 23/00.0076 size 3 core copper flexible wire fromconnector to ceiling rose/adoptorfixed as per manufacturers instructions and making necessary electricalconnections and testing on completioncomplete all as directed. Crompton cat NoCCS-103-05-65-SL-DP-NWH or equivalent in Philips/Havells/Wipro ). |
| 67 | S&F Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN2 way horizontal type, single door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed. |
| 68 | Supply and fixMCB single pole & neutral 40 Amps 240 volts, C series,10 kA rupturing capacity |
| 69 | M&L forsubmain wiring with 2 runs of 2.5 Sqmm single core PVC insulated, unsheathed, multi strandedcopper conductor and one single core 2.5 Sqmm PVC insulated , unsheathed , multi strandedcopper cable as earthing lead as per IS : 694 / 1990 drawn through and includingnon-metallic PVC rigid conduit of size 20/ 25 mm diaconcealedin walls etc with all accessories such as Tees, Elbows, junction box, reducers etc and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note :- 2 runs 2.5 Sqmm cable , one run2.5 Sqmmcableand one run of PVCshallbe measured as oneunit length) . |
| 70 | S & F exhaust fan sweep made of sturdy Engineering plastic complete with louvers shutter,voltage 230 V, 50 Hz, 1200 RPM noiseless,copper winding of sweep 300 mm with self closing louvers and fourblades fixed in position after necessarycutting wall tosizeas ordered to fix the fan as per manufactuers instructions , making good ofthe distured surface of wall as per its originalspecifications ,making necessaryelectricalconnection & testing on completion all as directed . .Make :- Havells/ Usha/ Crompton (Note:(i)The quoted is inclusive forany addtionalcutting ofwall& making good of disturbed surface ofwall to its originalspecifications). |
| 71 | Supply, install , testing and commissioning maintence free earth pit using 76 mm nominal bore pipe medium grade GI Pipe of 3 meter length as per IS 1239 , 15 Kg. Terec+ Ground Enhancing compound tested with Central Power Research Institute, Bangalore for \"Long Term stability\" of 2 years , 37.5 Kg. Earthcon Backfill compound along with 450x450 mm chamber work .Note :-(1).Contractor will executed the work as per soil resistivity reports given by same OEM. However to achieve the result less than 1 Ohm gridding of earth pit should not exceed 4 Nos of earth pits. (2). To achieve results less than 1 ohm contractor will provide gridding of earth pits as per soil resistivity test report ( but not more than 4 earth pit). Artificial treatment of 12.5 Kg earthon compound per 2 meter as per drawing attached and excavation and chemical required in area of gridding shall be included in rates quoted by contractor. (3) GIstrip required for inter connection of gridding of earth pit shall be paid separtely. (4). Total 1 nos of earth pits of above specification to be executed at site. However gridding will be decided as per requirement of earth result and as soil resistivity report. (5) GI strip of gridding shall be placed under groun level with the depth of 400 to 600 mm with the treatment of earthcon complound and alluvial soil as drawing.(6). removal of grabbles and stone and add some quantity of earth enhancement material in the soil using a black fill compound and make layer of black siol / garden soil/ alluvial soil, terrace, compound and earthcon compound repeat tye same procedure around the NB pipe electrode pipe as per drawing. (7).Compound shall be suplied in sealed bags. The earth electrode should finally be housed in heavy duty chamberwith cover of suitable size as per OEM recommendation . Ground Enhancing compound and Back-fill compound should be enviroment freindly, , ionic property to create ions for easy conduction , the compound should expand so much to remove entrapped air( bad conductor electricity ) andto creat strong conduction between electrode and soil , the compound should have a propertyto assist in absorbing humidity from theneightboringsoil to keep the earth pit moisture . The product should be tested and certified atCPRI for long term stability of earth pits. (8) Testing on completion & achiving resistance less than desire result & submitting report to Engineer-in Charge duly signed by userafter seccessfull completion of earthing whytime after euevution up to end of defect liabuility perioed. (9) Hot deep GI strip ofsize 50 x 6 mm from earth pit to testing point up to 7.5 mtr with protection pipe included in the quoted rates Make:- Jindal . TtaSteel / Zenith /Ashlok /Duval Mession / SGI Engineers Pvt ltd . |
| 72 | Supply & fix earth continuty conductor or main earthing of 50 x 6 mmGIstripi.e (roof conductor or down conductor ) above ground level fixed to wall/ roof dulyinsulated on batten or fixed on new PVC insulators with clamping device or recessed or chases or burried in groung/ floor or drawn in conduit/ pipe or fixed to poles or anyother indicated situation for loop earthing etc as required / ordered including testing on completion tothe satisfaction ofEngineer-in-charge. Note :- i) PVC insulator for earthing strip shall be measured & paid seperately .(ii)Quoted rate isdeemedtobe inclusive for fixing insulators .(iii) Thework earthing strip to beon roof top at lateral faces of existing hangers upto height of 25 mtrs.(iv) The quoted rate isdeemedtobe inclusive of protection pipe of 60 mm bore &working in above height.) |
| 73 | M&L to earthing pit chamber including replacement of PCC chamber, cement concret pit with cast iron miled steel frame embedded in the massonery enclouser finished flushed & PCCcover 10 mm thick (300mmx300mm size having locking arrengment hinged toPCCframe all as shown under electrical plate of SSR Pt - I 2009 and as directed includingpainting the external surface of chamber & cover with enamel paint in diffrent colour as directed and writing earth results & date of test carried out with white paint on black painted background, complete all as directed. |
| 74 | M&L for test point terminal block made of gun metal or phosphorus bronze size 75mm x 75mm x 25mm, drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screws with nuts & washers complete, fixed on ebonite sheet 6mm thick fitted on MS flat 50x5mm bent to shape etc, all as specified & as directed. |
| 75 | Supply only PVC insulator forGI/Aluminium strip supporter adequate to accomadate strip of 32 mm with fasteners complete all as specified and directed. |
| 76 | M & L for prepration of old painted surface of earth pit chamber & cover of any size & painting of the samewithtwo coats of synthetic enamel paint all as directed . |
