|
| 1 | SCHEDULE A BOQ |
| 2 | Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified and directed. |
| 3 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed. |
| 4 | Excavation in trenches n exc 1.5 m width and n exc 1.5 m depth and getting out in hard/dense soil complete all as specified and directed. |
| 5 | M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed |
| 6 | M& L PCC 1:4:8 type D2 (using 40 mm graded aggregate) as in foundation complete all as specified and directed. |
| 7 | M&L Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in mortar, complete all as specified and directed. |
| 8 | M & L 10 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 complete all as specified and directed. |
| 9 | M&L Preparing new surfaces ofplastered or unplasteredwall and applyingtwoof oil bound destemper over providing overputty of 2 mm thickness over plastered surface to prepare the surface even and smooth with Priming plastered and other surfaces with alkaliresistantpriming paint complete all as specified and directed. |
| 10 | M & L rendering 15 mm thick in CM 1:4 on external surfaces of brick wall and includingwater proofing compound use as manufacture instructions. |
| 11 | M&L Preparing new surfaces ofplastered or unplasteredwall and applying three coats of cement based paint complete wash complete |
| 12 | M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including crancking, bendingspirallyhooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. |
| 13 | All asper Item NO: 11 here in beforebut 5 mm dia and over upto and including 10mm dia as in stirrups spacers and binders complete all as specified and directed. |
| 14 | M&L Reinforcement cement concrete (nominal mix Type B0 1:2:4 (12.5mm grded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 15 | M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, griders, bressummers, lintels,cantilevers, shelves including supports, overhangs, etc. also splys between floors and beams, etc complete all as specified and directed. |
| 16 | M&L Reinforcement cement concrete (nominal mix Type B0 1:2:4 (12.5mm grded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed. |
| 17 | M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 18 | M&L for spreading and levelling in layers n exc. 25 cm thick and well ramming including watering as required complete all as specified and directed. |
| 19 | M&L for hardcore of gauge n exc. 63 mm, using broken stone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, wa-tered and rammed to a true surface complete all as specified and directed. |
| 20 | M&L for cement concrete type D-2, 1:4:8 (40mm graded agg) 100 mm thick as in floor, sub-base, etc. and finished the surface even and fair without using extra cement complete all as specified and directed. |
| 21 | M&L 75mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded stone aggregates), as in Plinth protection/ Path including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement,complete all as specified and as directed.Note :-The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm. |
| 22 | S & F MS tubular frames including special shaped washers etc complete using ERW or induction butt welded tubes confirming to IS 1161-1979 Gde St-240 and painted one shop coat of zinc primer including preparation of surfaces complete all as specified and directed. |
| 23 | S&F MS tubular purlins including brackets and all necessary connection complete all as specified and directed. |
| 24 | Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 25 | S&F mild steel work as in plain angle plates for securing purlins , band, strap, hold fast, bolt and nuts, cleat, hook, hinges, base tie for foor frame, support or stay for rain water pipe etc and other similar items conforming to Fe-410-0 or Fe-310-0 complete all as specified and as directed. |
| 26 | M&L for preparation of surfaces of new iron and steel surfaces of and two coat of synthetic enamel paint (ordinary tint) with a coat of red oxide primercomplete all as specified and directed. |
| 27 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cmcomplete all as specified and directed. |
| 28 | Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed |
| 29 | M&LFalse ceiling using GI snap grid(Everest regular T-2430 System or equivalent)size 610 x 610mm with main runner 38mm x 24.38mm, cross tee 29 x 240.30mm andwall angle 24 x 240.38mm suspended with 4mm dia GI wire fixed with steel dash fasteners carry maximum load upto 8.1Kg/Sqm with 4mm thick designer ceiling board (Lake and Hill of Everest or euivalent) complete all as specified and directed. |
| 30 | S&Fin repair steel window with side hung shutters incl. projecting type hinges with steel handles steel peg stay fixing lugs complete with glazingbar 10 cm devetailed or welded incl shop coat red oxide primer compete all as specified and as directed. |
| 31 | S&F in repair steel ventilator top hung shutter including hinges, steel peg stay, fixing lugs etccomplete with or without glazing bars all as specified and as directed by Engr-in-Charge. |
| 32 | S&F of 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as directed. |
| 33 | S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints all as specified and as directed. |
| 34 | S&F Flush shutters 30mm thick, solid core construction, with black board core and plywood face panels, comercial type on both faces complete all as specified and directed. |
| 35 | S&F Butt Hinges 100mm long, medium weight , cold rolled mild steel, and fixedcomplete all as specified and directed. |
| 36 | S&F Extruded Aluminium alloy handles 150mm long, fabricated type, anodised complete all as specified and directed. |
| 37 | S&F 200mm long Aluminium anodised towerbolt extruded section and fixed complete all as specified and directed. |
| 38 | S&F Aluminium alloy, anodisied, sliding door bolt with hasp, staple (bolt type), 300mm long and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed. |
| 39 | M&L for 15mm thick damp proof course in cement morar 1:2to horizontal or vertical surfaces including necessary formwork all as specified and as directed. |
| 40 | S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face fiixing in frame at site as per specification & drawing complete all as specified and directed. |
| 41 | S&F Solid PVC frame of size 50mm x 47mm made out of 5mm single sideprelam PVC sheet used in stead of plain colour PVC sheet & edges will be painted to match with prelam sheet complete all as specified and directed. |
| 42 | Glazed ceramic coloured tiles450x350x7mm thick set and jointed in neat cement slurry and pointed incolouredcement to match including rendering 10mm thick in CM 1:3 as in backing coat complete all as specified and directed. |
| 43 | Non skidcoloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tiles exc .11 Sqm but n.exc 0.18 Sqmin floors etc set and jointed in neat cement slurryand pointed in white or coloured cement to matchoverthe layer of screedbed15 mm thickfor laying floor finishes in CM 1:4 complete all as specified and directed. |
| 44 | Cutting chases for concealed water tubing or concealed conduit wiring etc and neaking good cutting not exc 10 cm grith complete all as specified and directed. |
| 45 | S&F of 3 layer PP-R polypropelyne random co popymer pipes 20 mm bore SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot and cold water including all PPR plain & brass threaded fittings fixed concealed to walls,ceilings or in floors etc complete all as specified and directed. |
| 46 | S&F of 3 layer PP-R polypropelyne random co popymer pipes 25 mm bore SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot and cold water including all PPR plain & brass threaded fittings fixed concealed to walls,ceilings or in floors etc complete all as specified and directed. |
| 47 | S&F of PP-R gate valves (brass insert) 25 mm dia complete all as specified and directed. |
| 48 | S&FBrass15mm CP mixer for mixing hot & cold water screwed down for iron pipeand fixed |
| 49 | M&L for 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed in repair |
| 50 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 51 | Demolition of brick work masonry, built in cement mortar including all quoins, pillars etc., complete all as specified and as directed. |
| 52 | Demolition of cement concrete (reinforced) in of any description and in any position and removal of debris out of MD land complete all as specified and directed. |
| 53 | Supply 600mm x 450 mm beveled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 54 | S & F in repairs Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm sizeincluding CP waste coupling, PVC connection 450 mm long,waste pipe & removing the existing Basin, cutting for and pinning ends of brackets or erecting stand complete all as specified and as directed. |
| 55 | S & F grating doom 125mm dia with waste hole of PTMT (min wt 40 gms) complete all as specified and directed. |
| 56 | S &F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as sepcified and directed. |
| 57 | Taking down PVC pipe incl fittings and S&F 110mm dia PVC SWR pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and as directed. |
| 58 | S&F 110mm dia PVC SWR bends of any radius with access door complete all as specified and as directed |
| 59 | Supply and Fix 15 mm bore pillar taps, capstan head, cast Copper alloy,chromium plated, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 60 | S&F vitreous chinasquatting pan \"Orissa\" pattern size 580x440mm white with intgeral foot rests(excluding flushing cistern and flush pipe) with \"P\" or \"S\" trap fron or back inlet etc including connection to trap tand flushing pipe and provision of lime concrete bedding complete all as specified and as directed in repairs including demolition of existing one complete all as specified and directed. |
| 61 | S&F 15mm dia, stop valve cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipe or for unions fixed in repair complete all as specified and as directed. |
| 62 | S&F 15mm dia, stop valve(concealed)/ Angle valve cast copper alloy CPfency type fixed in repair complete all as specified and as directed. |
| 63 | S&Fof swivel shower of PTMT any coloured for fixing with 15mm pipe (Minimum weight 40 gms) complete all as specified and as directed. |
| 64 | S&F 15mm bore Bibtaps, cast copper alloy,CPwith crutch or butterfly handle, screwed down, screwed for iron pipe, 15mm bore of pipe brass ferrulebut fancy type fixedin repair complete all as specified and as directed. |
| 65 | Taking down chowkatsor framesnot exceeding1.5 Sqmeachbut with shutters (without taking off shutters from the frames) all as specified. |
| 66 | Taking down chowkat with shutters(without taking off shutters from the frames) exc 1.5 sqm but n exc 4.0 sqm complete all as specified and directed. |
| 67 | S&F 100 mm long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11all as specified. |
| 68 | S&F Extruded brass handles, fabricated type polished all as specified |
| 69 | S&F 300 mm long, Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed all as specified |
| 70 | S&F Brass barrel tower bolts, withbarrel of extruded section and rolled or cast bolts and fixed all as specified |
| 71 | S&F 140mm long, floor door stopper of brass body and tongue, anodised,with hard drawn steel spring, fixed in floor complete all as specified |
| 72 | M&L Aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixedall as specified |
| 73 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not packing) removing of serviceable tiles to store and rubbish off the premises complete all as specified |
| 74 | M & L for Vitrified Ceramic tiles 10 mm thick, dark shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floor/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match (light shade) including screed bed 15mm thick in CM 1:4 complete all as specified and directed |
| 75 | M & L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cm 1:4 complete all as specified and as directed. |
| 76 | M&L for rendering 10mm thick on fair faces ofbrick or concrete surfaces in cement mortar 1:6, including finishing even and smooth without using extra cement complete all as specified and directed |
| 77 | M&L for applying two coats of distemper oil emultion white or tinted on new wall surfaces and including alkali resistantint priming paint over a coat of 1mm thick putty including preparation of new surfacescomplete all as specified and directed |
| 78 | M&L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 79 | M&L Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 80 | S&F of 12mm thick toughened glass for doors including polished by machine on edges including stainless steel clips/hinges, stainless handles (02 Nos), double action floor spring complete all as specified and as directed by Engr-in-Charge |
| 81 | Supply and fixing factory made uPVC white colour fixed glazed window/ ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately).Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance inimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 82 | Supply and fixing factory made uPVC white colour Three track three panelssliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 83 | S & F Powder coated anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade (AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. |
| 84 | S&F 4 mm thick, sheet glass, ordinary quality and glazingwithoil putty /beedingin squares exceeding 0.5 sqm each pane for fixing to aluminium/wooden joinery work complete all as specified. |
| 85 | S&F Stainless steel wire cloth, 0.36mm dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed by Engineer-in-Charge. |
| 86 | M&L for 25mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed |
| 87 | Rounding for edges of store slab one edge, such as in steps cooking platform and other similar work. |
| 88 | S & F 12mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work i complete all as specified and directed |
| 89 | S & F Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved complete all as specified and as directed by Engneer-in-Charge |
| 90 | S & F Stainless steel spring hinges of size of approved pattern and make suitable for base/wall unit of modular kitchen Including taking down the existing one complete all as specified and directed (Make : BIR SS or equivalent make as per list of makes) |
| 91 | S & F Magnetic catches with 8mm dia steel ball and brass body and striking plate including letting in & Including taking down existing one complete all as specified and as directed by Engineer-in-Charge |
| 92 | S & F Stainless steel handles of size 150 mm of approved pattern and make suitable for Base/Wall unit of modular kitchen Including taking down the existing one complete (Make : Spykar or equivalent make as per list of makes) |
| 93 | S&F in repairs vitreous china wash down single piece water closetwall hung type with UF soft close slim seat cover, hinges dual flush cistern fittings and fixing accessories, of size 375x670x750mm incl P trap complete all as specified & directed.Make : Cat NoLYS-WHT- 3885P180UFSMN of Jaquar or equivalent |
| 94 | S&F in repairs Health faucet chromium plated suitable for 15 mm dia pipe with 1.00 metre long flexible tube and ABS wall hook with NRV including makingconnections and fixed in position complete in all respect as specified.Make :Cat NoALD-CHR-577 of Jaquar or equivalent |
| 95 | S&F in repairs table top wash hand basinvitreous china of size 640x425x155mmincl fixing accessories complete all as specified and as directed. Make :Cat NoJDS-WHT-25901 of Jaquar or equivalent |
| 96 | S&F in repairs Pillar tap of 15mm dia chromium plated cast copper alloy of fancy typescrewed down for iron pipecomplete all as specified and directed.Make : Cat No : ARI-CHR-39011 of Jaquar or equivalent |
| 97 | S&F in repairs Brass Chromium plated waste coupling of 32 mm dia with screwed shank and fly nuts complete all as specified and directed. |
| 98 | S&F in repairs PVC connections 15mm size with PTMT nuts and washersfor 450mm long pipe complete all as specified and directed. |
| 99 | S&F in repairs Bib taps of 15mm dia chromium plated cast copper alloy of fancy typescrewed down for iron pipecomplete all as specified and directed.Make : Cat No ALI-CHR-85037 of Jaquar or equivalent |
| 100 | S&F in repairsconcealed stop cock & flush cock with fitting sleeve, operating lever & adjustable wall flange with sealof 15mm diaCP fancy typecomplete all as specified and directed.Make : Cat No ALI-CHR-85083 of Jaquar or equivalent |
| 101 | S&F in repairs vitreous china urinal bowl withfixing accessories, of size 355x340x535mm complete all as specified & directed.Make : Cat NoURS-WHT- 13261 of Jaquar or equivalent |
| 102 | S&F in repairsCP urinal valve auto closing sys with built in control cock &wall flange with of 15mm dia complete all as specified and directed.Make : Cat No PRS-CHR-077 of Jaquar or equivalent |
| 103 | S&F in repairsrectangular shaped urinal partition with frosted glass of 8mm thick of size 450mmx 900mmwith CP wall clamps complete all as specified and directed.Make : Cat No JSE-CHR-810US450X of Jaquar or equivalent |
| 104 | S&F in repairs CP single towal rail ,600mm long stainless steel complete all as specified and directed.Make : Cat No AKP-CHR-35711PS of Jaquar or equivalent |
| 105 | S&F in repairs CP paper holder with flap recessed type (stainless steel) complete all as specified and directed.Make : Cat No AHS-CHR-1553 of Jaquar or equivalent |
| 106 | S&F in repairs CP soap dispenser with glass bottle complete all as specified and directed.Make : Cat No AKP-CHR-35735P of Jaquar or equivalent |
| 107 | M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 108 | M&L 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice laminationfixed with screws to frame work all as specified and directed. |
| 109 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard/dense soil. |
| 110 | M&L forPCC 1:2:4type B1using20 mm graded stoneaggregateas in pillars, post holes and mass concrete complete all as specifiedand directed |
| 111 | S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted , bolted or welded attachment. (Fe 410 -W (Gde- E-250) quality -A complete i all as specified and as directed. |
| 112 | Supply, installation, testing and commissioning of electric induction motor of 3 phase, 415V, 3.75 kW / 5 HP capacity including chain pulley arrangement, gear box with ratio 1:60 with multi-stage gear reduction system as a single pair of gears including gear wheels etc by lifiting existing hangar door for extending existing door wheel shaft and fabrication work to install hangar door motor gear assmebly, motor to gear box chain driving work, motor cable stay wheels work and limit switch stay work complete all as specified and directed by Engr-in-Charge. |
| 113 | Supply & fixing of 3 phase, 415V 5HP DOL panel, push button for forwarding/ reverse movement of the doors, relays, limit switches, contactors,siren, ammeter and voltmeter, indicating lamps, MCB SP/ SPN of various capacities and suitable connecting cable including VFD driver 3.75 to 4/5hp KW of capacity etc and necessary fabrication work required to install panel complete all as specified and directed by Engr-in-Charge. |
| 114 | Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 4 core complete all as spcified and directed. |
| 115 | Supply and fix PVC insulated and FRLS PVC Round Sheathed, Copper Conductor (flexible) industrial cable, 1100 Volt, 2.5 sqmm 4 core complete all as spcified and directed. |
| 116 | Supply and fix of cable rolling wheel for laying of cable from panel to motor etc complete all as specified and directed by Engr-in-Charge. |
| 117 | Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly inground (Earth pit not less than 2.25 Mtr deep below normal ground level) with topedge of the plate not less than 1.5 Mtr belownormal ground level connecting with galvanizediron GI earth strip 32x6mm as earthing lead by means ofbolt nut check nuts and washersof galvanized iron and provision of GI tubing medium grade (ISI marked)of size 15mm for protection of GI earth wire upto test point, 20mm dia GI light grade watering pipe with funnel and wire mesh, RCC pit cover of size 300x300x40mm reinforced with XPM having weight not less than 4Kg/sqmm including 6mm thick MS bar handle made to shape, PCC pit with 1:3:6 type C1 with angle iron frame made of angle iron of size 40x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate,earth work in any type of soil,all as required at site complete all as specified in plate No 3 of SSR Part-I and all as specified orindicatedincludingtesting on completion.Note:- Rates inclusive of necessaryearth work, PCC pit, RCC cover, funnel with watering pipe, GI earth wire upto 7.5 m long for connecting totest point etc. all as required at site for complete earthing. |
| 118 | S&F of Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32x6mm galvanised iron strip complete all as specified and directed. |
| 119 | M&L for Sand cushioning of cables provided with a layer of sand 8 cm deep before laying the cable and 15 cm depth after punning down and stretching the cable complete all as specified and directed. |
| 120 | Supply and lay Fire bricks, size 230 x113 x 75 mm for the protection of LT UG Cable in trenches complete all as specified and directed by Engineer-in-Charge. |
| 121 | Wiring complete with 1.5 sqmm single core PVC insulated, unsheathed FRLS 1100 volts grade,FRLS cable and incl non metalic PVC conduit with accessories in wall/roof/ceiling/hangar steel frames etc incl Modular terminal boxes fabricated with 1.6mm MS sheet concealed to wallscovered with white cover plate with frame etc and 1.5 sqmm PVC insulated, unsheathed copper conductor multistrandedcable 1100V grade as earth continuity conductor & connecting to common earth dolly all as specified for |
| 122 | One light point/fan/bell point controlled by one switch |
| 123 | All as per above but for one switch socket outlet 3 pin 5 Amps on independent board |
| 124 | All as per above but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently |
| 125 | S&F modular switch 1 way 6 Amps, 1 module complete all as specifiedand directed |
| 126 | S&F modular switch 1 way 16 Amps, 1 module complete all as specifiedand directed |
| 127 | S&Fmodular socket outlet multipurpose 2/3 pin 6 amps, 2 module complete all as specifiedand directed |
| 128 | S&Fmodular socket outlet multipurpose 2/3 pin 6/16 amps, 2 module complete all as specifiedand directed |
| 129 | S&F white cover plate with frame, 3 Module complete all as specifiedand directed |
| 130 | S&F white cover plate with frame, 6 Module complete all as specifiedand directed |
| 131 | S&F metal flush box 3 module complete all as specifiedand directed |
| 132 | S&F metal flush box 6 modulecomplete all as specifiedand directed. |
| 133 | S&F electronicmodular fan regulator 230 volts, step type socket type, hum free 120 watt 2 Module complete all as specifiedand directed. |
| 134 | Supply and fixing 4 feet, LEDlight fitting18 watts(T-8) with out put of not less than 110lumens/watts , boxtype made with epoxy white powder coated CRCA sheet steel(decorative) light fitting having G13 bipin holders compitable for mounting on wall/ceiling/surface,ermisible limit of CRI range,with recommended burning hours ,4000K/6500Ketc , 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driverconnector block etc complete with all accessories internally pre wired andnecessary mounting arrangements, including provision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting with integrated driver ofLED tube rod 4\" x 18 watts complete all as specified and as directed. |
| 135 | Supply and fixing 2 feet, LEDlight fitting 10 watts(T-5) with out put of not less than 110lumens/watts , boxtype made with epoxy white powder coated CRCA sheet steel(decorative) light fitting having G13 bipin holders compitable for mounting on wall/ceiling/surface,ermisible limit of CRI range,with recommended burning hours ,4000K/6500Ketc , 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driverconnector block etc complete with all accessories internally pre wired andnecessary mounting arrangements, including provision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting with integrated driver ofLED tube rod 2\" x 10 watts complete all as specified and as directed. |
| 136 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five starrated with brushless direct current motor (BLDC) complete all as specifiedand directed. |
| 137 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specifiedand directed. |
| 138 | Supply and fixing factory madepowder coated distribution board SPN 8 way, double doorincludingbus bar, Neutral bar, standard DIN rail, earth bar acomplete all as specified and directed |
| 139 | S&F MCB SPN32 Amp , 240 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacitycomplete conforming to IS 8828 of 1996 all as specified |
| 140 | Supply and fixing singlepole MCB 6 to 32 Amps, 240 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacity conforming to IS 8828 of 1996all as specified |
| 141 | S&F1-ph,two pin with earth, metal clad earth plug socket with sheet metal enclosure controlled by Single pole MCB 5 to 32(selection of MCBrating & its load curve should be match with load) Amps-01 No capacity operating on 230 V AC 50Hz electric supply complete |
| 142 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protectioncomplete all as specifiedand directed. |
| 143 | Sub main wiring for circuit complete with 2 X 6 sqmm single core PVC insulated, unsheathed FRLS1100 Volt grade multi stranded copper conductor cable drawn through and incl suitable size PVC Casing capping and accessories complete fixed surface to wall/roof/ceiling etc and incl 1 X 6 sqmm single core PVC insulated, unsheathed FRLS 1100v grade multi stranded copper conductor cable as earth continuity conductoretc and all as specified. |
