|
| 1 | Surface dressing n exc 15 cm deep and getting out in hard/dense soil complete all as specified and directed. |
| 2 | Excavation in trenches nexc 1.50 mtr wide and n exc 1.50 mtr depth, for foundation etc n exc 10Sqm on plan and getting out in hard/dense soil complete all as specified & directed. |
| 3 | Returning, filling in, including spreading levelling watering and well ramming in layers nexc 25cm as in soil complete all as specified and directed. |
| 4 | Removing excavated material nexc 50m and depositing where directed at a level nexc 1.5m above the starting point with soil complete all as specified and directed. |
| 5 | M&L for PCC 1:4:8 type D-2 (40 mm graded stone aggregate) as in foundation, filling and mass concrete, sub base etc complete all as specified and directed. |
| 6 | M&L for broken stone or boulder hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 7 | M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate in foundation, including rafts, footings, beams, plinth beams; bases for columns; etc; basement slabs, under-remed piles and mass concrete complete all as specified and directed. |
| 8 | M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in cloumns, pillars, piers, posts and struts complete all as specified and directed. |
| 9 | M & L for RCC (nominal mix) 1:2:4 Type B1 using 20mm graded aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 10 | Formwork to sides of concrete foundations,footings, bases of columns, raft and raft beams, sidesand soffits (if any) of foundation and plinth beams andsimilar work vertical or to batter rough finished concrete surfaces completed all as specified and directed. |
| 11 | Formwork to sides of pillars, piers,columns,square, rectangular, polygonal, circular on plan rough finished surfaces of concrete completed all as specified and directed. |
| 12 | Formwork to sides and sofits of floor or roof beams, beam haunching, bressummers, lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc rough finished surfaces of concrete completed all as specified and directed. |
| 13 | S&F MS TMT bars10mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding with mild steel wire (annealed)not less than 0.90mm dia confirming to Fe 500 or Fe 550 complete all as specified and directed. |
| 14 | All as per item No. 13 above but but 5mm dia and over upto and including 10mm dia in stirrups spacers and binder. |
| 15 | M&L for brick work with sub class \"B\" old size bricks straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed. |
| 16 | M&L for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thickwalls built in CM 1:4 complete all as specified and directed. |
| 17 | M&L for 10mm thick renedering on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed. |
| 18 | M&L 15mm thick rendering on fair faces of brick surfaces in CM (1:4) finished surfaces even and smooth without using extra cement complete all as specified and directed. |
| 19 | S&f Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 20 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.(Note: stainless steel/Aluminium butt hinges and necessary SS/Aluminium screws shall be paid separately) |
| 21 | S & F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 22 | S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays150mm long (1 no.). hinges type B-2, 100mm long (2 no.) suitable handle (1Nos.) complete all as specified and directed. |
| 23 | S & F 3.0 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5Sqm in each pin complete all as specified. |
| 24 | S&F 100mm butt hinges extruded aluminum alloy with galvanised mild steel hinge pin anodised type B-21 complete all as specified and directed. |
| 25 | S&F 300mm long aluminium alloy.anodised, sliding door bolt with hasp,staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 26 | S&F aluminium, anodised, barrel tower bolts of extruded section and fixed of size 150mm long complete all as specified and directed. |
| 27 | S&Faluminium anodised handlefabricated typeof size150 mm complete all as specified and directed. |
| 28 | M&L Moorum/red bajri filling in floors orpavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 29 | M&L for 75mm thick PCC 1:3:6 type C-2(using 40mm graded stone agg) as in plinth protection complete all as specified and directed. |
| 30 | M&L 40mm thickPCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floor finished even and rough complete all as specified and directed. |
| 31 | Supply only integral water proofing compound complete all as specified. |
| 32 | M&L for preparation of newly plastered surfaces of wall and applying two coats distmper oil emulsion over a coat of 1 mm thick wall care putty complete all as specified and directed. |
| 33 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 34 | M & L for non skid ceramic coloured & designer tiles 7 to 8 mm thick (square rectangular ) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floors laid over & including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified and as directed. |
| 35 | M & L for glazed ceramic coloured & digital tiles 350 x 250 x 7/450x350/7mm thick on vertical surfaces of wall set and jointed in neat cement slurry and pointedin white/coloured cement tomatch the shade of tiles complete all as specifed and directed. |
| 36 | S&F brass chromium plated/SS shower rose 125mm size Chromium plated shower roses with or without swivel joints, anysize, including fixing to steel pipe or union complete all as specifed and directed. |
| 37 | S&F vitreous china water closet squatting pan\"orissa pattern, ivory coloured of size 580 x 440 mm,with integral foot rest and outlet for \"P\" or \"S\" trap , WC pan shall be set in lean concrete below level of rim of pan to receive the floor finish complete all as specified and directed. |
| 38 | S&F PVC (SWR) floor trap75mm, with grating including jointing with solvent cement complete all as specified and directed. |
| 39 | S&F for Soap dish any type, fixed to plugs with chromium plated brass screws fixed complete all as specified and directed. |
| 40 | S & F 10 ltrs capacity PVC flushing cistern, low or high level, with inlet, ball valve, syphonic action type, float and handle, pull or push type including brackets complete all as specified and directed. |
| 41 | S&F 15 mm dia fancy type CP stop valves/angle cock, cast copper alloy fancy type chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 42 | S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 43 | S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 44 | S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed. |
| 45 | S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed. |
| 46 | S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. |
| 47 | S&F PVC (SWR)\"P\" trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. |
| 48 | S&F PVC connections 15mm size with PTMT nuts of length 450mm long complete all as specified and directed. |
| 49 | S&F 15mm bore GI tubing medium grade galvanized with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed. |
| 50 | S&F 20mm bore GI tubing medium grade galvanized with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed. |
| 51 | S&F 15mm fancy type CP dia bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 52 | S&F 15mm Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 53 | S&F vitreous china white counter oval shape wash hand basin of size 630x450mm incl brackets complete all as specified and directed. |
| 54 | S & F PVC waste pipe 32 /40 mm dia x 600 mm long complete all as specified. |
| 55 | S&F waste coupling brass CP for glazed ware sink, WHB etc with long screwed shanks and fly nuts complete of 32mm dia.etc. complete all as specified and directed. |
| 56 | S&F 15mm fancy types Pillar taps, cast copper alloy, with capstanheads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed. |
| 57 | S&F32mm brass chromium plated bottle trap for wash basin/sink with inlet and outlet screwed for pipe or connections including necessary packing, union and cap bore of trap 32mm complete all as specified and directed. |
| 58 | S&F for 600x450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 59 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed. |
| 60 | S&F Brass chromium plated /SS Tubular towel rail, 20mm dia, D type, 60cm long between flanges and including Chromium plated brass screws and wooden /plastic cleats. (Minimum weight 190gms) complete all as specified and directed. |
| 61 | S&F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 62 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed. |
| 63 | S & F mild steel flat iron as in wind tie for roof including securing bolts confirming to Fe 410-W (Gde-E-250) quality-A complete all as specified and directed. |
| 64 | S&F Anodised aluminium snap grid frame work for false ceiling Size of grid 605 x 605mm including Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5 mm dia. 40mm long complete and including materials and labours for 6mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI /Aluminium frame work with screws complete all as specified and directed. |
| 65 | S&F 500 ltrsrotational moulded polyethylene water storage tanks (cylindrical vetical with threadedclosed top) with PVC float valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrulehoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed. |
| 66 | S&F 1000 ltrsrotational moulded polyethylene water storage tanks (cylindrical vetical with threadedclosed top) with PVC float valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrulehoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed. |
| 67 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil complete all as specified and directed. |
| 68 | S & F Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars , stiffeners , gusset plates, Fe-410- W(Gde E-250) quality B etc.complete all as specified and directed. |
| 69 | S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-410- W(Gde E-250) quality B etc.complete all as specified and directed. |
| 70 | S&F Welded steel wire fabric (mesh) Weight N. exc 4 kg per square metre any size supplied and fixed complete to wood or steel members complete all as specified and directed. |
| 71 | M&L for applying two coats of synthetic enamel paint over new prepared steel surface over a coat red oxide primer over 10 cm width or girth complete all as specified and directed. |
| 72 | M&L for preparationof new or previously untreated surfaces of steel of any description, not exc 10cm in width or girth when unconnected with other painting and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 73 | S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, securing urinals to plugs with and including 60mm long brass screws, fixing flush pipe, grating and union for discharge pipe complete all as specified and directed. |
| 74 | S&F brass CP Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed. |
| 75 | S&F 15mm dia fancy type push taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 76 | M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding rates including moulding and rounding including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white cement to match complete all as specified and directed. |
| 77 | M&L for providing precast cement concrete louvres and jallies, 35 mm thick (measured solid), Type B-0, 1:2:4 (using 12.5 mm graded aggregate) including all mouldings but excluding frame, set in 1:6 cement mortar including necessary formwork if required complete all as specified and directed. |
| 78 | M&L for 150mm dia reinforced cement concrete pipe class NP-2 laid and joionted with collars complete all as specified and directed. |
| 79 | M&L forPCC 1:4:8 type D-2, using 40mm graded agg as in concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 150 mm bore complete all as specified and directed. |
| 80 | M&L for rendering 15mm thick in CM 1:4intwo layers on fair faces of brick work or concrete surfaces 10mm first coat and 5mm second coat finishing the surfaces even and smooth with using integral water proofing compound complete all as specified and directed. (WPC shall be measured and paid separately). |
| 81 | M&L for pecast RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in cover slabs of manholes, open drains inclusive of form work set in CM (1:4) complete all as specified. (Reinforcement shall be measured and paidseparately) |
| 82 | S&F MS TMT bars 6-8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding with mild steel wire (annealed)not less than 0.90mm dia confirming to Fe 500 or Fe 550 complete all as specified and directed. |
| 83 | M&L for PCC 1:2:4 type B-2 using 40mm graded stone aggregte as in surface channels & drain including necessary form work complete all as specified and directed. |
| 84 | M&L for PCC (1:24) type B-1 using 20 mm graded stone agg as in coping etc complete all as specified and directed. |
| 85 | S&F Mild steel round bars 10mm dia and over as in rungs, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips confirming to Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde - E-165) complete all as specified & directed. |
| 86 | M & L for point wiring with 1.5 Sqmm (Nominal Area) FRLS PVC insulated sheathed multi stranded copper conductor, 1100 Volts drawn through and including rigid non metalicconcealedconduit medium grade ISI marked minimum 20mm size and its accessories complete along with 1.5 sqmm cable but in green colour as continuous earthing wire and connecting to common earth dolly completely concealed,in walls/ ceiling/ roofs with and including 1.2mm thick MS sheet terminal boxes duly fabricated flush mounting in the wall for mounting modular switches, socket, bell push, fan regulators etc. as required with modular frame and cover of 1 module to 18 module as required at siteall as specified and as directed for the following points :- |
| 87 | One light/fan point controlled by one 1-way switch. |
| 88 | One 3 pin 5 Amps socket point on the same board with other switches. |
| 89 | All as per item No.86 here in before but wiring with 4 sqmm unsheathed single core PVC insulated multistranded copper conductor for 3 pin 15 Amps socket outlet complete all as specified and directed. |
| 90 | S&F Switch modular type 6A 240 Volts complete all as specified and directed. |
| 91 | S&F modular socket 6 A- 2/3 pin combined 2 module complete all as specified and directed. |
| 92 | S&F ceiling rose surface type Bakelite 65 x 50 mm with three terminals complete all as specified and directed. |
| 93 | S & F Lamp holder, PVC / Polycarbonate angular type complete all as directed. |
| 94 | S & F LED lamp base B-22(holder type) 7 watts, 230 Volts complete all as directed. |
| 95 | S&F metallic heavy duty steel body Exhaust fan continuous duty with louvers, blades, with fixing arrangements & making hole of suitable size if necessary for 250 mm sweep, 230V, AC single phase including nuts, bolts and washers complete all as specified and directed. |
| 96 | S&F LED lights fitting 1x16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 97 | S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt, 220 volt AC decorative type withdriver, holders,including LED lamp connecting up with three core flexible copper conductor of suitable size complete all as specified and directed. |
| 98 | S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics with IP 65 protection including GI Bracket for security lights made out of medium grade GI Pipe 50mm dia 1.2 mtr long bend to shape as directed, fixed on walls with two Nos MS clamp/saddles as required at site including nuts, bolts and washers complete all as specified and directed. |
| 99 | S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece, 304 grade braided stainless steel connection pipe for HOT and COLD water complete all as specified and directed. |
| 100 | S & F sheet metal enclosure with socket plug top and MCBs single pole and neutral with a two pin and earth plug and socket complete with single pole neutral MCB of 20A, 240V complete all as specified and directed. |
| 101 | S & F sheet metal enclosure (for DB\"s when MCBs to be used), single pole and neutral single door, 8 way, 240 Volts complete all as specified and directed. |
| 102 | S & F MCB Single pole 240 volts 6-32 Amps, 10KA, B-series complete all as specified and directed. |
| 103 | S&F MCB SPN,220V 25 KA, \"B\" curve 40-63A current carrying capacity complete all as specified and directed. |
| 104 | S & F sheet metal enclosure (for DB\"s when MCBs to be used), Triple pole and neutral (TPN), single door, 4 way, 415 Volts complete all as specified and directed. |
| 105 | S & F MCB, 415 volts 63 Amps,TPN 25KA, B-series complete all as specified and directed. |
| 106 | S & F MCB double pole 240 volts 40 Amps,16KA, B-series complete all as specified and directed. |
| 107 | S & F second class hard wood rectangular blocks 30 x 25 x 5 cm closed recessed type complete all as specified and directed. |
| 108 | M & L for submain wiring with 2 runs of single core 4 sqmm size PVC insulated unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC conduit and its accessories including provision of one run of 4 sqmm PVC insulated single core unsheathed copper multistranded conductor cable as earth continuity wire complete all as specified and directed. Note :-2 runs of cable, one run of earth wire (copper cable) & one run of PVC conduit shall be measured as one running metre. |
| 109 | M&L for earthing complete with galvanized steel earth plate electrode 60x60x6mm thick buried directly in ground (earth pit ndot less than2.25 mtrs deep below ground level) with top edge of the earth plate at a depth of not less than 1.5 mtr below ground level connected to galvanized iron wire 4 mm dia as earthing lead by means of bolts, nuts and washers made out of GI/steel earth strip protected by GI light grade pipe of 40 mm dia and connecting to main panel board/switch board/control board all shown in electrical plate No 3 of SSR Pt I incl PCC chambers in 1:2:4 and RCC cover slab with 8mm dia MS bars reinforced at 10 cm center to center both ways incl earth work like excavation, returning filling back disposal etc complete all as specified and directed. |
| 110 | Supply, laying and testing ofLT underground cable XLPE insulated sheathed and armoured with aluminium stranded conductors LT 1100 Volts grade ofsize 16 Sqmm 4 core complete all as specified and directed. Note:Earth work, sand and brickswill be measured and paid under relevant items. |
| 111 | Supply and laying of DWC (double Wall corrugated) HDPE polyethiline pipeOuter dia of 50 mm and inner dia 38 mm, including couplers, bends, cap etc. with smooth internal and profiled external surface for non pressure under ground cable complete all as secified and directed. |
| 112 | S&F GI pipe light grade 40mm dia for cable protection fixed to poles / bldg incl two Nos MS clamps made to shape out of 25 x 3mm MS flat and painting incl bolt, nut, washer etc.complete all as secified and directed. |
| 113 | M & L test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including3 Nos 8 mm dia 25 mm long hexagonal head screw complete all as secified and directed. |
| 114 | Supply and laying GI water tubing 40 mm bore, medium grade galvanized with all fittings (such as tee, elbow, flanged, long socket, union, short pieces) and fixed to wall or ceiling or laid in floor, duct and trenches etc complete all as specified and directed.Note: - Quoted rates deemed to be included for road cutting / wall floor and making good damaged portion matching with existing surface with all existing finishes. |
| 115 | Supply and laying GI water tubing for 25 mm bore, medium grade galvanized with all fittings (such as tee, elbow, flanged, long socket, union, short pieces) and fixed to wall or ceiling or laid in floor,duct and trenches etc complete all as specified and directed. Note: - Quoted rates deemed to be included for road cutting / wall floor and making good damaged portion matching with existing surface with all existing finishes. |
| 116 | Supply and laying GI water tubing for 20 mm bore, medium grade galvanized with all fittings (such as tee, elbow, flanged, long socket, union, short pieces) and fixed to wall or ceiling or laid in floor,duct and trenches etc complete all as specified and directed. Note: - Quoted rates deemed to be included for road cutting / wall floor and making good damaged portion matching with existing surface with all existing finishes. |
| 117 | S & F 40mm dia gun metal gate valve with inner wheel head, screwed both ends in iron pipe complete all as specified and directed. |
| 118 | S & F 25mm dia gun metal gate valve with inner wheel head, screwed both ends in iron pipe complete all as specified and directed. |
| 119 | S & F 20mm dia gun metal gate valve with inner wheel head, screwed both ends in iron pipe complete all as specified and directed. |
| 120 | Cutting the existing GI / CI / MS pipe of 40mm to 100mm bore and inserting CI /GI / MS Tee of size including all fittings, welding /Lead joints and earthwork complete all as specified and directed. |
