|
| 1 | FD-1031 - Almirah Large steel with shelves:Almirah shall be fitted with ISI marked 75mm 6 lever lock with three way locking system (Make of lock -Godrej/Harrison/Link). Almirah shall be finish withtwo coats of synthetic enamel paint (shade as approved by GE) upto obtaining glossy finish over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 2 | FD-69(M) - Book shelf open large steel : Overall size shall be 915 mm long,305 mm wide and 1905 mm height. Book shelf shall be finish withtwo coats of synthetic enamel paint for obtaining glossy finish over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 3 | FD-1029 - Locker bed side steel: Overall size shall be 760 mm long, 600mm vide and 1100 mm high. All MS sheet shall be 1mm thick. All steel and iron surfaces shall be finished withtwo coats of synthetic enamel paint upto obtaining glossy finish over a coat of redoxide primer with Spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge. |
| 4 | FD/E6/MAP/12 - Chair writing : The frame of the chair shall be of 16 gauge 25mm dia MS tubular frame. Back shall be designed with contoured lumber support for extra comfort.12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lipping alround shallbe provided at seat and back. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 5 | FD-1038 - Rack 6 tier steel : Overall size shall be 915 mm long,610 mm wide and 1905 mm height measured from outside, All steel and iron surfaces shall be finished with two coats of synthetic enamel paint upto obtaining glossy finished over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 6 | FD-1043 - Trestle store room steel : Trestle shall be of overall size of 2440x600x300 mm. All members, strut and bracing shall be welded properly with good finishing. All steel surfaces shall be finished with two coats of synthetic enamel paint upto obtaining glossy finished over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 7 | FD-1003 - Table office offcers steel : Top shall be 18 mm thick prelaminated particle board both side laminatedduly covered with half round beading in matching shade with synthetic adhesive(Fevicol SH). All steel and iron surfaces shall be finished with two coats of synthetic enamel paintupto obtaining glossy finish over a coat of redoxide primer with Spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 8 | FD-1004 - Table office clerk steel : Top shall be 18 mm thick prelaminated particle board both side laminatedduly covered with half round beading in matching shade with synthetic adhesive(Fevicol SH). All steel and iron surfaces shall be finished with two coats of synthetic enamel paintupto obtaining glossy finish over a coat of redoxide primer with Spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 9 | CWE/TEZ/04 - Charpoy MS tubing plywood top : Plywood shall be BWR grade, fitted with nut and bolts. Head board shall have 18mm thickExterior grade both side prelaminated particleboard fitted with half round teakwood beading all around with good finishing .PVC shoes shall be provided to legs of charpoy. All steel members shall be finished with two coats of synthetic enamel paint upto obtaining glossy finish over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper in black colour.Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 10 | FD-256 - Chair Verandah : The frame of chair shall be of 20 mm dia mild steel conduit of well thickness as 1.6 mm made to shape as shown on drawing. Caning shall be done with 4mm wide cane in mat pattern or as directed by Engineer-in-charge in the seat, back and hand rest portion. PVC/hard rubber shoes shall be provided to the bottom of all legs. All exposed iron surface shall be finish with two coats of synthetic enamel paint for obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper.Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 11 | FD-1008 - Table 3\"x2\" steel with drawer :- Steel tube shall be 25 mm dia with 1.6 mm thickness.Drawer shall be fitted with ISI marked 75mm 6 lever lock and decorative handle. Top shall be 18 mm thick exterior grade MDF board one side laminated shade or as approved by GE,duly covered with 4 mm thick half round teak wood beading in matching shade with synthetic adhesive(Fevicol SH).All steel surfaces shall be finished with (shade as approved GE) two coats of synthetic enamel paint upto obtaining glossy finished over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 12 | FD-1026 - Stool revolving : Overall size shall be 455mm dia and 600mm hiight. 12mm dia mild steel bar ring shall be provided at 150mm from bottom joining four legs as show on drg. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge. |
| 13 | FD-77 - Foam without back :- Steel tubes of 25 mm of 16 Guage,Wooden seatplank shall be first class seasoned hard wood free from knots and defects. Seat plank of size 1800x255x25 mm,shall be fitted with counter sunk head bolts.Wooden planks surface shall be french polished with glossy finish.All exposed iron surface shall be finished with (Shade as approved by GE) two coats of synthetic enamel paint for obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper.Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 14 | FD-78 - Foam with back :- Steel tubes of 25 mm of 16 Guage,Wooden seat and back plank shall be first class seasoned teak wood free from knots and defects. Seat plank of size 1800x255x25 mm, Back rest plank of size 1800x150x19 mm shall be fitted with counter sunk head bolts.Wooden planks surface shall be french polished with glossy finish.All exposed iron surface shall be finished with (Shade as approved by GE) two coats of synthetic enamel paint for obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper.Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 15 | FD-243 - Almirah steel med with shelves :- Overall size shall be 760 mm,440 mm wide and 1270 mm height. 1mm thick MS sheet shall be used to manufacture Almirah except legs. Two Legs shall be provided to almirah as shown on drawing and shall be of 1.25 mm thick MS sheet. Cromium plated stainless steel godrej type handle100mm long shall be fixed on shutters, Almirah shall be fitted with ISI marked 75mm 6 lever lock with three way locking system. Almirah shall be finish withtwo coats of synthetic enamel paint (shade as approved by GE) upto obtaining glossy finish over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 16 | FD-1009 - Table 3\"x3\" steel:- Steel tube shall be 25 mm dia with 1.6 mm thickness. Top shall be 18 mm thick prelaminated particle board both side laminatedduly covered with half round beading in matching shade with synthetic adhesive(Fevicol SH).All steel surfaces shall be finished withtwo coats of synthetic enamel paint upto obtaining glossy finished over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 17 | FD-1007 - Table 3\"x2\" steel without dwr :- Steel tube shall be 25 mm dia with 1.6 mm thickness. Top shall be 18 mm thick prelaminated particle board both side laminatedduly covered with half round beading in matching shade with synthetic adhesive(Fevicol SH).All steel surfaces shall be finished withtwo coats of synthetic enamel paint upto obtaining glossy finished over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge. |
| 18 | NOTE : (Applicable for all items):-(i)The bidders/contractors are advised to read relevant Contract drawings and Particular specifications, Key specifications, Special conditions and General conditions of Contracts before entry/quoting the rates.(ii) The items are to be manufactured as per relevant drawings and specifications and supplied to the Department. |
