|
| 1 | Demolition of Cement Concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 2 | M&L for 25 mm thick PCC 1:2:4 type B0 (Using 12.5mm graded stone aggregate) in sub base of floorings complete all as specified and directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposal ofdebris and rubbish to outside MD land complete all as specified and directed. |
| 4 | M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed. |
| 5 | M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, as in vertical surfaces such as skirting/dado etc, including 10 mm thick screed bed in cement mortor 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed. |
| 6 | M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/ rectangular) area of Each tile exc 0.11 Sqm but n.exc 0.18 Sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed. |
| 7 | M & L for glazed, coloured, ceramic, tiles of size (350mm x 250 mm/450mm x 350mm/300mmx450mm) x6 to 7 mm thick, on vertical surfaces such as skirting, dados etc, including 10 mm thick backing coat in cement mortor 1:4 and set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed. |
| 8 | M & L for 6mm thick anti-static Epoxy flooring system consisting of preparation of existing surface and application of two component ,high solid ,epoxy resin based floor primer and followed by fixing of copper foils tapes over 2 - 3 mm three components, epoxy based self-levelling screed as conductive under coat and after 24 hours it is followed by an application of 2-4 mm thickepoxy resin floor topping as conductive top coat ( total system of 6mm thick) of approved sky-blue colour and pattern as per the manufacturer\"s instructions including taking down existing PVC mat flooringall as speicfied and directed.Make: (i) Epoxy resin based floor primer :- Nitto Primer 25 of M/s Fosroc Checmicals / SMARTCARE AFCOFLOR HFP 130 of Asian Pain or equivalent approved make as per the list of manufacturer\"s(ii) Epoxy based self-levelling screed and epoxy resin floor topping:- Nitto floor SL of M/s Fosroc Checmicals / SMARTCARE AFCOFLOR ESD SL of Asian Paint or equivalent approved make as per the list of manufacturer\"s |
| 9 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets/snap grid etc complete all as specified and directed. |
| 10 | S & F aluminium Anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed by the Engr-in-Charge. |
| 11 | M & L for 6 mm thick, seam less calcium silicate ceiling made out of600 x 600 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face to centre, board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish complete all as specified and directed. (Note : Frame work for ceiling shall be measured and paid separately |
| 12 | M & L for Preparation new surfaces of ceilings etc of any description over 10 cm width or girth not otherwise described by \"Vacuum based sanding machine\" and applying two coats of oil bound distempert over a coat of primer by \"Aquto Roller\" machine complete all as specified and directed. |
| 13 | Resecuring or easing & adjusting without taking down the shutters of any description exc 2.0 sq. m each complete all as specified and directed. |
| 14 | M & L for 100 mm thick, plain cement concrete 1:4:8,type D-2 (using 40 mm graded stone aggregate)as in sub-base of flooring, paving etc complete all as specified and directed. |
| 15 | M & L for Sand filling under floors or in foundations including spreading, levelling, watering and consolidation complete all as specified and directed. |
| 16 | M & L for Machine pressed precast conctete coloured/multi coloured interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed. |
| 17 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 18 | M & L for cement concrete (1:2:4), type B1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork complete all as specified and as directed. |
