|
| 1 | Excavation in trenches Notexceeding 1.50 m wide and not exceeding 1.50 deep and 10 Sqm plan and getting out in hard dense soilcomplete all as specified & directed. |
| 2 | Returning, filling in trenches, including spreading, levelling, watering and well ramming in layers not exceeding 25 cmcomplete all as specified & directed. |
| 3 | Removing excavated material not exceeding 50 mtrs and depositing where directed at a leval not exceeding 1.50 m above starting point in soilcomplete all as specified & directed. |
| 4 | Material & labour forHardcore of broken stone gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as dierected. |
| 5 | Material & labour for Cement concrete 1:4:8 type D2 using 40 mm graded stoneaggregate in foundations, filling and mass concretecomplete all as specified & directed. |
| 6 | Material & labour for Plain Cement Concer 1:2:4 type B1 using 20mm graded stone aggregate as in coping, bed block hold fast etc complete all as specified & directed. |
| 7 | Material & labour forPCC (1:3:6) Type C-2 using 40 mm graded aggregate as in foundationor mass concrete allas specified and directed. |
| 8 | Material & labour forReinforced cement concrete (design mix) M-25 using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concretecomplete all as specified & directed. |
| 9 | Material & labour forReinforced cement concrete (design mix) M-25 using 20 mm graded stone aggregates as in column,pillarscomplete all as specified & directed. |
| 10 | Material & labour for Pre-cast cement concrete 1:3:6 type C1 usnig 20mm graded crushed stone aggregateblock masonry with solid blocks, exc. 10 cm in width and setting in mortar 1:6,complete all as specified & directed. |
| 11 | Material & labour foruse and waste of timber as in formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for rough finished surfaces of concrete flatcomplete all as specified & directed. |
| 12 | Material & labour foruse and waste of timber as in formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for rough finished surfaces of concrete flat complete all as specified & directed. |
| 13 | Material & labour for Rooftrusses (framed), trussed, purlins, crane gantries, rails andERW Fe-410w (gde 250 B) or induction butt weldied tubes conforming to IS-1161-1979 grade St240 fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified & directed. |
| 14 | Supply & Fixing for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete W(GdeE-250) quality Bcomplete all as specified & directed. |
| 15 | Mild steel TMT bars 10mm dia and over, cut tolength, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less complete all as specified & directed. |
| 16 | Mild steel TMT bars5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 17 | Supply & Fixing for pre painted galvatume aluminium zinc coating GI based corrugated/ trapizoidal shape steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as inroof coverings/cladding to wall,fixed with self tapping screwscomplete all as specified & directed. |
| 18 | Supply & Fixing forpre painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as inroof coverings/cladding to wall,fixed with self tapping screws complete all as specified & directed. |
| 19 | Material & labour for 100 mm thick cement concrete type D-2, 1:4:8 using 40mm graded stoneaggregate complete all as specified and directed. |
| 20 | Material & labour for40 mm thick Plain Cement Concrete 1:2:4 Type B1 using 20mm graded stone aggregate as in sub floorscomplete all as specified & directed. |
| 21 | Material & labour for 15 mm thick rendering with Cement Mortar1:4on concrete surfacefinishedeven and smooth without using extra cement complete all as specified & directed. |
| 22 | Material & labour for 15 mm thick rendering with Cement Mortar 1:6on concrete surfacefinishedeven and smooth without using extra cement complete all as specified & directed. |
| 23 | Material & labour forpreparation of newplastered surface and applying 2 coat cement base paint over a coat of primercomplete all as specified & directed. |
| 24 | Material & labour forpreparation of newplastered surface and applying 2 coat of oil bound distemper over a coat of primercomplete all as specified & directed. |
| 25 | Material & labour forfor preparing new steel surfaces and applying two coat of synthetic enamel paint over a coat of red oxide zinc chromeprimer on steel surfaces of any description over 10 cm width or girth incluidng necessary preparation of surfacecomplete all as specified & directed. |
| 26 | Material & labour forfor 3.4mm thich high gloss exterior grade aluminium compisite wall panelclading including all aluminium frame and fixing and sealing the gap with slicon sealentincluding making and fixing name boardwith PVC lettersof approved size and patterncomplete all as specified & directed. |
| 27 | Supply and layBricks common burnt clay building bricks sub-class \"B\" Designation 75, size 230mm x 115mm x 75mm flat perpendicular to axis of cable for protecting complete all as specified and directed. |
| 28 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded,galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 core including taking down old complete all as specified and directed. |
| 29 | Supply and fixing in replacement LED Post of lantern, 40W,Total lumens 2250 ,5700 K,Potted driver ,systemetric beam including 32 mm dia GI Pipe,medium grade , 1.8 meter length complete all as specified & directed. |
| 30 | Supply and Spread Natural Riddled soil in trenches for cushioning and covering to cable complete all as specified and directed by Engineer-in-Charge. |
| 31 | Material & labour forfor cutting road / hard standing to depth not exceeding 60 CM and to width not exceeding 45 CM for laying HDPE Pipes and making good the disturbed surfacesby 1:3:6 type C1 using 20 mm graded stone aggregate complete all as specified and as directed. |
| 32 | Supply and laying High density polyethylene pipes(HDPE) of 32mm dia pressure rating 6 kgf/cm2 laid in trenches and fixed on poles complete all as specified and directed. |
| 33 | Material & labour forfor cable joint kit straight through heat shrink typefor 1.1KV (Earthed) grade cable complete with jointing material and accessories siutable for XLPE insulated armoured aluminum conductor cable of size 25/50 sqmm, 3.5 core complete all as specified & directed. |
| 34 | Supply & Fixing in replacement of weather proof junction box of internal size 250 x 200 x105 complete with hinged door ,locking arrangementand consisiting of 04 Nos aluminium bus bar of 50 Amps capacity ,MCB SP 6 Amps ,10 KA suitable size flanged type brass cable entry glands confirming to IP 65 complete fixing arrangement on street light pole,complete all as specified & directed. |
| 35 | Material and labour in replacementPVC insulated,PVC round sheathed multicore industrial copper cable of size 3 Core ,1.5 Sqmmfor voltage grade upto 1100 V,as per IS 694complete all as specified & directed. |
| 36 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 37 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital orsimilarpattern roof coveringcomplete all as specified & directed. |
| 38 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embeddedportion in concrete portion and making good disturbed groundcomplete all as specified & directed. |
