Tender For Renovation And Up-Gradation Of Iiib Type Houses, Replacement Of Windows And Kitchen Cupboards In Iiia Type Houses In West Campus At Iit Delhi., Delhi-Delhi

TDR : 53192727

Tender Notice
BOQ

8 Days Left

Delhi , Delhi

Tender Brief : Tender For Renovation And Up-Gradation Of Iiib Type Houses, Replacement Of Windows And Kitchen Cupboards In Iiia Type Houses In West Campus At Iit Delhi.

Document Fees
Refer document

EMD
₹ 143195.0 /-

Tender Value
₹ 71.59 Lakhs /-

Submission Date
07-01-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Civil Work
2	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
3	All kinds of soil.
4	Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level :
5	1:2:4 (1cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
6	1:4:8 (1Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources)
7	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
8	Centering and shuttering including strutting, propping etc. and removal of form for
9	Shelves (Cast in situ)
10	Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete above plinth level.
11	Thermo-Mechanically Treatedbars of gradeFe-500D or more.
12	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :
13	Cement mortar 1:4(1 cement :4 coarse sand)
14	Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
15	Cement mortar 1:3(1 cement :3 coarse sand)
16	Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry.
17	Providingandfixing 18mmthickgangsawcut,mirrorpolished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters,window sills,facias andsimilar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.
18	Granite stone slab of colour black, Cherry/Ruby red
19	Area of slab upto 0.50 sq
20	Area of slab over 0.50 sqm
21	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
22	Granite work
23	Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.
24	Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
25	Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
26	Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 10 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).
27	Providing and fixing ISI marked flush door shutters conforming to IS : 2202(PartI)non-decorative type,core of blockboardconstruction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:
28	35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
29	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.
30	Fixed to openings /wooden frames with rawl plugs screws etc.
31	Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :
32	250x16 mm
33	Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :
34	200x10 mm
35	150x10 mm
36	100x10 mm
37	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
38	125 mm
39	100 mm
40	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
41	Twin rubber stopper
42	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
43	1.0 mm thick
44	Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.
45	With 12 mm mild steel U beading
46	Providingand fixingbright /matt finishedStainless Steelhandles of approved quality & make with necessary screws etc all complete.
47	100mm
48	Providing and fixing stainless steel sof closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge.
49	Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approvedmake500mmlongwithscrewsetc. complete as per direction of Engineer- in-charge,
50	Providingand fixingready made304 grade stainless steelModular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirementincludingfinishing (wherever required)andfittings.The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in- charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately)
51	Providing and fixing 2 mm thick 16 to 19 mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per direction of Engineer- in-charge.
52	Providing and fixing T-iron frames for doors, windows and ventilators of mildsteel Tee-sections, jointsmitredandwelded,includingfixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.
53	Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C.1:3:6 (1Cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size).
54	Providing andlayingCeramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.
55	Providing and laying Vitrified tiles in floor with diferent sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).
56	Size of Tile 600x600 mm
57	Providing gola 75x75 mm in cement concrete 1:2:4(1 cement :2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design :
58	In 75x75 mm deep chase
59	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
60	15 mm cement plaster on the rough side of single or half brick wall of mix:
61	1:4(1 cement: 4 fine sand)
62	12 mm cement plaster finished with a floating coat of neat cement of mix:
63	1:3(1 cement: 3 fine sand)
64	6 mm cement plaster of mix:
65	1:3(1 cement :3 fine sand)
66	Providing andapplyingplaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.
67	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
68	Two or more coats on new work
69	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
70	Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approvedbrandandmanufacture,includingapplyingadditionalcoats wherever required to achieve even shade and colour.
71	Two coats
72	Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.
73	With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre
74	Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
75	Finishing walls with Acrylic Smooth exterior paint of required shade:
76	Old work (Two or more coat applied @ 1.67 Itr/ 10 sqm) on existing cement paint surface
77	Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.
78	With cement mortar 1:4 (1 cement : 4 fine sand)
79	Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.
80	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.
81	Nominal concrete 1:3:6 or richer mix (including equivalent design mix)
82	Nominal concrete 1:4:8 or leaner mix (including equivalent design mix)
83	Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
84	Demolishingbrickworkmanually/bymechanicalmeansincluding stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
85	In cement mortar
86	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :
87	Of area 3 sq. metres and below
88	Of area beyond 3 sq. metres
89	Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :
90	Of area 3 sq. metres and below
91	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.
92	For thickness of tiles 10 mm to 25 mm
93	For thickness of tiles above 25 mm and up to 40 mm
94	Demolishingbricktilecoveringinterracingincludingstackingof serviceable material and disposal of unserviceable material within 50 metres lead.
95	Demolishing mud phaska in terracing and disposal of material within 50 metres lead.
96	Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :
97	75 to 80 mm dia pipe
98	100 mm dia pipe
99	Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :
100	15 mm to 40 mm nominal bore
101	Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.
102	Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
103	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :
104	W.C. pan with ISI marked white solid plastic seat and lid
105	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
106	White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
107	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :
108	Kitchen sink without drain board
109	610x510 mm bowl depth 200 mm
110	Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
111	Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia
112	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
113	Flexible pipe
114	32 mm dia
115	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
116	Providing and fixing soil, waste and vent pipes :
117	100 mm dia
118	Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989
119	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :
120	For 100 mm dia pipe
121	Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.
122	100 mm dia
123	Sand cast iron S&S as per IS - 3989
124	Providing and fixing plain bend of required degree.
125	100 mm dia
126	Sand cast iron S&S as per IS : 3989
127	Providing and fixing collar :
128	100 mm
129	Sand cast iron S&S as per IS - 3989
130	Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :
131	100 mm
132	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
133	100 mm inlet and 100 mm outlet
134	Sand cast iron S&S as per IS: 3989
135	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall
136	20 mm dia nominal bore
137	25 mm dia nominal bore
138	32 mm dia nominal bore
139	Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :
140	20 mm dia nominal bore
141	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work
142	25 mm dia nominal bore
143	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :
144	25 to 40 mm nominal bore
145	Providing and fixing uplasticised PVC connection pipe with brass unions :
146	45 cm length
147	15 mm nominal bore
148	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work):
149	20 mm nominal bore
150	25 mm nominal bore
151	Providing and placing on terrace (at all floor levels) polyethylene water storagetank,IS : 12701marked,withcoverandsuitablelocking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
152	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
153	15 mm nominal bore
154	Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.
155	15 mm nominal bore
156	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.
157	15 mm nominal bore
158	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
159	15 mm nominal bore
160	Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge.
161	Cutting holes up to 30x30 cm in walls including making good the same:
162	With common burnt clay F.P.S. (non modular) bricks
163	Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :
164	100 mm diameter
165	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :
166	100 mm diameter S.W. pipe
167	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:
168	100x100 mm size P type
169	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
170	Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :
171	For pipes 100 to 250 mm diameter
172	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) :
173	For fixed portion
174	Powder coated aluminium (minimum thickness of powder coating 50 micron)
175	Forshuttersofdoors,windows&ventilatorsincluding providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
176	Powder coated aluminium (minimum thickness of powder coating 50 micron)
177	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):
178	With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
179	Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.
180	Upto 5 mm depth and 5 mm width
181	Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete.
182	355 X 19 mm
183	Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
184	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the Engineer-in-Charge”:
185	With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
186	Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type orof approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
187	25 mm average thickness
188	Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust freesteel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
189	Bars upto 12 mm diameter
190	Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as perspecifications and direction of Engineer- In-charge complete in all respect.
191	Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make
192	Providing and injecting approved grout inproportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-Charge. (The payment shall be made on the basis of actual weight of approved grout injected.)
193	Epoxy injection grout in concrete/RCC work of approved make
194	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVCfoil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/ kitchen cabinet etc. of required sizes comprisingof virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread offlame of Class Acategory with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge.(Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)
195	18 mm thick
196	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain white color board for backing of cup boards and bathroom/kitchencabinetsetc.ofrequiredsizecomprisingofvirgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimumcompressive strength 50 N/mm2, modulus of elasticity 850 N/ mm2 and resistance to spread offlame of Class Acategory with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel screws etc. all as per direction of Engineer-In- Charge.(Note: stainless steel screws shall be paid separately)
197	6 mm thick
198	Driling and fixing NRV nozzles in RC members, including (fixing material : Renderoc Plug of Fosroc / Sikadur-31 of Sika / MasterBrace 2200 of BASF or equivalent of Pidilite & Krishna Conchem).i. Drilling Holes: Drilling 12 mm dia, 50 to 75 mm deep holes or upto required depth in structural members of the intervals of 350 mm in staggered manner or as directed by the Engineer-in-charge in RC structural elements.ii. Cleaning of holes: Clean the holes by air blower prior to fixing nozzles.iii. Fixing of Nozzles: Insert 12mm dia. NRV nozzles in cleaned holes. External end of nozzles to be machine to receive outlet of grouting gun. Fix it inside the holes by applying thyrotrophic epoxy putty to ensure complete sealing. Cure the system for min. 12 hrs.iv. Cuttting of Nozzles: Cut the nozzles by chisel after completion of grouting without damaging structural elements:
199	Providing mixing & applying pre-batched one component polymer modified dual shrinkage compensated thixotropic cementious patch repair mortar as per the manufacturer specifications and as per the direction the Engineer-in-charge. The comperessive strength of polymer modified mortar shall be ≥ 45 Mpa (28 Days) according to ASTM C109.( Product :- Renderock S2 of Fosroc/ SikaTop® 122 HS of Sika /MasterEmaco S 348 of BASF or equivalent of Pidilite)
200	For 20 mm thickness over slab, beams, columns and stair case slabs .
201	Providing and laying anticorrosive Treatment of Reinforcement by any approved make rebar corrosion protection system to existing reinforcement (The application shall be by brush). Process is to be complete as per the recommendation of manufacturer and direction of Engineer-in-charge. for payment exposed length of reinforcement will be measured. (Product - NITOZINC PRIMER of FOSROC / Sika MonoTop-1010 IN of Sika/ MasterEmaco P 130 of BASF or equivalent of pidilite & Krishna Conchem).Bars Upto 12 mm diameter
202	Providing and fixing cup board shutters with 18-19mm thick commercial block board as per IS : 1659 of approved make with necessary SS piano hinges of appropiate size etc. complete as per direction of Engineer In Charge.
203	Providing and fixing cup board inside shelves, sides, back portion, drawers etc. with 18-19mm thick commericial block board as per IS : 1659 of approved make with necessary fixing arrangement and as per requirement complete as per direction of Engineer In Charge. (All exposed edges of block board to be lipped with 3 mm thick teak wood beading/ margin.)
204	ProvidingandfixingCPbrass single lever basin mixer without popup waste with 450mm long braided hoses (connection pipes) of approved design as per directions of Engineer-In-Charge.
205	Providingandfixing Glass Corner Tray / Corner Shelf of size 11\"x11\" of approved design as per directions of Engineer-In-Charge.
206	Providingandfixing 140mmdiaStainless Steel Grating with frame (withorwithouthole) of approved design as per directions of Engineer-In-Charge.
207	Providing and fixing Chrome Finish 600mm long towel rail of approved design with required acceessoriesas per directions of Engineer-In-Charge.
208	Providing and fixing CP brass with soap dish holder with all complete as directed by the Engineer-in-Charge.
209	Providing and fixing Hand Shower (Health Faucet) with 8mm Dia and one meter long flexible tube and wall hook of approved make as per the directions of Engineer-In-Charge.
210	Providing and fixing chrome finish wall mounted regular Kitchen Sink Mixer with Swinging Spout of approved make as per the directions of Engineer-In-Charge.
211	Providing and fixing overhead shower 150 x 150 mm square shape multi flow (ABS Body chrome plated with gray face plate) with rubit cleaning system and 304mm long CP Brass square shower arm with wall flange of approved make and design as per the directions of engineer-in-charge.
212	Providing and fixing stainless steel (Grade 304) curtain rods having weight upto 0.72 kg./metre with necessary S.S. bracket (Grade 202) and end showcap fixed with S.S screws and rawal plug complete as per direction of Engineer-in-charge.Size: 25mm dia (Heavy Type)Note:- For payment purpose total end to end length of rod including End Globe will be measured and no extra payment will be made for Curtain Bracket, End Knob, Pipe Holder, Finials and rings.
213	Electrical Work
214	Wiring for light point/Ceiling fan point/ exhaust fan point/ call bell point with 1.5sq.mm FRLS/HFFR PVC insulated copper conductor single/multi core cable in surface/ recessed steel conduit, with modular switch, modular plate, suitable GI box & earthing the point with 1.5sq.mm. FRLS/HFFR PVC insulated copper conductor single core etc as reqd.
215	Group A
216	Wiring for twin control light point with 1.5sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit,2 way modular switch, modular plate, suitable GI box & earthing the point with 1.5sq.mm. FRLS/HFFR PVC insulated copper conductor single core etc as reqd.
217	Wiring for light/ power plug with 2X4 sq.mmFRLS /HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No 4 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as reqd.
218	Wiring for light/ power plug with 4X4 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 2 Nos 4 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthng as reqd.
219	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class steel conduit as required
220	2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
221	2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
222	2 X 4 sq. mm + 1 X 4 sq. mm earth wire
223	4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire
224	Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in existing surface/ recessed steel/ PVC conduit as required
225	3 X 1.5 sq. mm
226	3 X 2.5 sq. mm
227	3 X 4 sq. mm
228	6 X 4 sq. mm
229	Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.
230	2 Pair
231	Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
232	Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit or cutting the wall and making good the same in case of recessed conduit as required.
233	25 mm
234	32 mm
235	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
236	20 mm
237	25 mm
238	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
239	5/6 amps switch
240	2 way 5/6 amps switch
241	15/16 Amp switch
242	3 pin 5/6 amp socket outlet
243	6 pin 15/16 amp socket outlet
244	Telephone socket outlet
245	TV antenna socket outlet
246	Bell Push
247	Supplying and fixing stepped type 2 module electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
248	Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
249	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.
250	1 or 2 Module (75mmX75mm)
251	6 Module (200mmX75mm)
252	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
253	Supplying and fixing 3pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc. as required.
254	Supplying and fixing brass batten/ angle holderincluding connection etc. as required.
255	Supply, Installation, Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories ,suitable for 9-20W LED B-22 Base including connections etc. as required.
256	Supplying and fixing bell/ buzzer suitable for single phase, 230 volts, complete as required.
257	Providing and fixing M.S. Fan Hook clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required.
258	Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator)
259	12 way, Double door
260	16 way, Double door
261	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
262	Single pole
263	Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
264	40 amps
265	63 amps
266	Supplying and fixing DP sheet steel enclosure on surface / recess along with 25/32 amps 240 volts \"C\" curve DP MCB complete with connection,testing and commissioning etc as required.
267	Supplying and fixing 20 amps, 240 volts, SPN industrial type,socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
268	Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
269	Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
270	Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
271	Supplying, installation, Testing & Commissioning of LED Surface Down lighter (Round/square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%,Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%, P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) <19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), lifetime of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard.Manufactures Word Mark/ Name Engraved/Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sqmm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management:heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).Powder coated die cast /Extruded aluminium Body including trim .
272	15 Watt
273	Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light(includingdismentaling of existing lights on buy back basis) of following body material and construction as per IS : 10322 with driver (Replaceable) as per the equirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range-5 °C to 40 °C, internal surge protection of 2.5 KVwith Short & Open circuit protection, THD < 10%, P.F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K(As per ANSI Bin), SDCM(Standard DeviationColour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard.Manufactures Word Mark/ Name Engraved/Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sqmm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management:heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).
274	Powder Coated CRCA Sheet Body(Thickness ≥ 0.50mm)
275	20 Watt
276	Supplying and installation of Surface mounting Mirror light with following features:- Suitable for operating voltage and frequency: 130-300 Va.c, 50 Hz.; wattage 10 Watts; Length 450-600mm; Nominal surge protection 2.5 kV; IP 54 complete in all respect i/c external connections with 1.5 sqmm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required..
277	Supplying and installation of Surface wall mounting bracket LED bulk head with energy efficient electronic driver with following features:- Suitable for operating voltage and frequency: 130-300 Va.c, 50 Hz.; wattage 10 Watts;Output lumens not less than 1000 lm; CCT 6500K; Nominal surge protection 2.5 kV;Power factor not less than 0.9, IP 66 complete in all respect i/c external connections with 1.5 sqmm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required.
278	Supply and fixing and connecting & commissioning following LED lamps in existing fitting as reqd.LED bulb 5W to 10 W.
279	Supplying, installation DLP mini- trunking 32mm x 20mm with independent cover etc. complete as reqd.[Make Legrand]
280	PVC mini trunking with independent cover of size 32mm x 20mm size.
281	PVC mini trunking End cap left or right.
282	PVC mini trunking Internal/ External angle from 60°-120°
283	Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC)Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies,shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion)less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required.
284	900mm, service value ≥ 5.1 CM/Min/Watt, air delivery 130 CM/Min (Minimum)
285	1200mm, service value ≥ 6.0 CM/Min/Watt, airdelivery 210 CM/Min (Minimum)
286	Supplying and fixing of 250 mm size fresh air fan complete with suitable size louvers with all accessories suitable for use on 230 V , 50 Hz supply in the existing opening, including making good the damage , connection, testing and commissioning etc. as required.as required
287	Supplying and fixing of 300 mm size,1400 rpm exhaust fan complete with suitable size louvers with all accessories suitable for use on 230 V , 50 Hz supply in the existing opening, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor single/ multi core cable and making good the damage , testing and commissioning etc. as required.
288	Dismantling/ Disconnecting old damages services.
289	Dismantling, disconnecting old damaged unserviceable fl fitting/ exhaust fan/ ceiling fan/ bulkhead fitting with bracket etc. as reqd.
290	Dismantling damaged DB/TPN Switches/AC box, loose wire boxes along with all accessories as required.
291	Dismantling of switch / socket /regulator etc. with MS board as reqd.
292	Credit of Dismantle Material
293	Credit of dismantle of old Iron Scrap like steel windows / door frames, MS grills, MS bars, GI pipe and fittings etc.
294	Credit of dismantle of old Wooden Scrap like old flush doors, wooden frames, ply, board etc.
295	Credit of dismantle of old PVC scrap like PVC cistern, PVC tanks, PTMT fittings etc.
296	Dismentaled old M.S.boxes with backelite sheetof different sizes
297	Dismentaled of old 36 Watt batten Fittings
298	Dismentaled of old wall bracket Fittings
299	Dismentaled of old 1200mm / 1400mm Ceiling Fans
300	Dismentaled of old Copper wires
301	Dismentaled of old SPN/TPN MCB,s
302	Dismentaled of old 5 Amp switches
303	Dismentaled of old 5 amps sockets
304	Dismentaled of old 15 amps switches
305	Dismentaled of old 15 amps sockets
306	Dismentaled of old fan regulators

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents

Also Visit

Tenders

Delhi Tenders

Furniture Tenders

Furniture Items Tenders

Cabinet Supply Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Renovation And Up-Gradation Of Iiib Type Houses, Replacement Of Windows And Kitchen Cupboards In Iiia Type Houses In West Campus At Iit Delhi., Delhi-Delhi

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Renovation And Up-Gradation Of Iiib Type Houses, Replacement Of Windows And Kitchen Cupboards In Iiia Type Houses In West Campus At Iit Delhi., Delhi-Delhi

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us