|
| 1 | Clearing and grubbing road land including uprooting vegetation, grass, bushes, shrubs, saplings and trees of girth up to 300 mm, removal of existing stumps of trees dead or cut earlier stacking serviceable material for use or auction within the road land & disposal of all unserviceable material including removal top 150mm thick organic soil away from the road land as under Clause no. 201, specification for Road & Bridge work of MORT&H (5th revision) including full compensation all operations, all inclusive costs, contigencies, incidentals involved for finished defect free item of work complete as per specification and direction of the Engineer-in-charge |
| 2 | Earthwork in Excavation for road works in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers ,trimming buttom and side slopes inaccordance with requirements of lines ,grades,and cross sections ,transporting to the embankment location within all lifts and leads upto 1000 mtr. as per Clause 301 of MoRT&H Specifications for Road & Bridge works (5th Revision)and as per direction of Engineer-in-Charge. |
| 3 | Loosening, leveling and compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150mm. mixed with water of OMC and then compacted by rolling so as to achieve minimum dry density as given in table 300-2 for embankment construction and clause 305 of MORT&H specification for Road & Bridge works(5th Revision) |
| 4 | Construction of embankment with approved materials deposited at site from road-way cutting and other structures with all lifts and leads graded and compacted to meet requirement as per approved drawing and technical specifications as per Section 900 and Clause 305 of MoRT&H Specification for Road & Bridge works (5th Revision) and as per direction of Engineer-in-Charge. |
| 5 | Construction of embankment with approved materials obtained from borrow pit and other structures with all lifts and leads graded and compacted to meet requirement as per approved drawing and technical specifications as per Section 900 and Clause 305 of MoRT&H Specification for Road & Bridge works (5th Revision) and as per direction of Engineer-in-Charge. |
| 6 | Providing compacted Sub-base shoulder with granular materials by using moorum of approved quality and satisfying the required P.I. value as per approved drawing and technical specifications as per Section 900 and Clause 407of MoRT&H Specifications for Road & Bridge works (5th Revision) and as per direction of Engineer-in-Charge |
| 7 | Providing fine dressing and turfing the slopes of the road embankment & revetment with compact Dub grass with all lifts and within initial lead of 1 km. and as per the direction of the Engineer-in-charge. |
| 8 | Construction of granular sub-base by providing close graded Granular sub-base Grading-VI materials including all cost of materials with cost of all labour, T&P etc. as per table 400-2, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MORT&H Specification for Road & Bridge works ( 5th Revision). |
| 9 | Providing, laying, spreading and compacting graded stone aggregate to Wet mix macadam specificationincluding all cost, conveyance of materials with cost of all labour, T&P etc. including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per clause 406 of MORT&H specification for Road and Bridge works(5th Revision). |
| 10 | Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surfce and spraying primer @ 0.6kg. per sqm.using mechanical broom as per Clause 502 of MORT&H Specification for Road & Bridge works (5th Revision.) |
| 11 | Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor @ 0.2kg. per sqm.on prepared bituminous/granular surface cleaned with mechanical broom as per Clause 503 of MORT&H Specification for Road & Bridge works (5th Revision.) |
| 12 | Providing & laying 50 mm thick av. compacted Bituminous Macadam (Grading-II) using VG-30 Bitumen with Hot Mix Plant 100-120 TPH using crusher broken hard granite aggregates of specified grading premixed with bituminous binder @ 3.3 % by weight of total mix and filler, transporting the hot mix to works site, lying with Hydrostatic Paver Finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled vibratory and tandem rollers to achieve the desired compacting as per Clause No. 504 and section 900 of specifications for Road and Bridge works of Ministry of Road Transport & Highways (5thRevision) &including cost of all materials, labour, T&P,taxes, royalty etc complete in all respect and as per direction of the Engineer-in-charge. |
| 13 | Providing and laying 25 mm thick av. compacted Semi Dence Bituminous Concrete (Grading-II) using VG-30 grade Bitumen and crusher broken hard granite aggregates of specified grading, premixed with bituminous binder @ 5.0 per cent of mix and filler, transporting the hot mix 100-120 TPH to work site, laying with a hydrostatic paverfinisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause No.501, 508 and section 900 of specifications for Road and Bridge works of Ministry of Road Transport & Highways (5th Revision) & including cost of all materials, labour, T&P, taxes, royalty etc complete in all respect and as per direction of the Engineer-in-charge. |
| 14 | Providing and fixing 80mm thick cement concrete of M40 grade Interlocking paver blocks of approved quality and shapes including cost labour TandP etc complete as per drawing and Technical Specifications and as per specification and direction of Engineer in charge |
| 15 | Supplying and fixing of precast kerb stone of size 300mm x 300mm x 150mm of machine with proper compaction fixed with requirede pattern etc all complete in all respect confirming to IS 5758:1984 and as per specification and direction of Engineer in chargae |
| 16 | Painting two coats with approved Synthetic enamel paints of approved colour/ shade including sand papering, polishing the surface, cost, conveyances, taxes of all materials, labour with T&P required for the work etc complete as per specification and direction of the Engineer in charge |
| 17 | Dismantling of presstressed / reinforced M-20 grade and above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material with all lifts and lead of 1000 meters etc. complete as per specification and direction of Engineer in charge |
| 18 | Dismantling of Cement Concrete Grade M-15 and M-20 including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material with all lifts and lead of 1000 meters etc. complete as per specification and direction of Engineer in charge |
| 19 | Filling foundation and plinth with good quality river sand including watering with cost, conveyance, royalty, taxes of all materials, labour with T&P required for the work etc complete as per specification and direction of the Engineer-in-charge |
| 20 | PCC M-15 Grade using 40mm and down grade size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts including frame works including cost, conveyance of all materials, cost of all labour, T&P, cost of all materials etc. complete as per direction and specification of Engineer-in-charge Levelling course |
| 21 | In substructure (Box culvert and Toe wall) |
| 22 | In substructure (Hume pipe culvert) |
| 23 | RCC M-25 Grade using 20mm and down grade size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts including frame works including cost, conveyance of all materials, cost of all labour, T&P, cost of all materials etc. complete as per direction and specification of Engineer-in-charge Foundation |
| 24 | In substructure |
| 25 | In superstructure |
| 26 | Providing Fe-500 HYSD reinforcement (SAIL/ RINL/TATA/JINDAL STEEL/ SHYAM STEEL) for RCC works including bending, binding & placing in position as per specification of Drawing & design including cost, conveyance of all materials, all labour and T&P etc. complete as per the specification and direction of the Engineer-in-charge. |
| 27 | Providing and laying of metal spall backing in the rear side of abutment and wing wall using 5cm sizie hard granite metal to a thickness not less than 600mm with smaller size towards the soil and bigger size towards the wall and provided the entire surface etc complete as per specification and direction of Engineer in charge |
| 28 | Reinforced cement concrete crash barrier at the edges of the bridge structures, constructed with M-40 grade concrete with HYSD reinforcement conforming to IRC:21 and dowel bars 25 mm dia, 450 mm long at expansion joints filled with pre-moulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No. RW/NH - 33022/1/94-DO III dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineerand as per Technical Specifications section 809 of MORTH specification for Road & Bridge works (5th revision) |
| 29 | Gravel backing to apron and revetment below slope pitching etc. complete including cost, conveyance, royalty, taxes of materials, labour, T&P required for the work etc. complete as per direction of the Engineer-in-charge |
| 30 | Rough stone dry packing in aprons and revetments, stone pitching in slopes and boulder apron etc with hard stone of size 30 cm and above and weighing not less than 40Kg as per approved drawing and Section 900, 1000 & 2500 of specifications for road and bridge works of Ministry of Road Transport & Highways (5th Revision) & including cost of all materials, labour, T&P, taxes, royalty etc complete in all respect and as per direction of the Engineer-in-charge. |
| 31 | Providing weep holes in Plain/ reinforced concrete abutment, wing wall/ return wall with 100mm dia A.C.Pipe, extending through the full width of the structure with slope of 1V:20H Complete as per drawing and Technical specifications etc. complete with cost, conveyance, taxes, royalties of all materials, cost of all labour,T&P, sundries etc. complete as per specification and direction of the Engineer-in-charge |
| 32 | RCC M-30 Grade in Wearing coat using 20mm downgraded size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts including form works etc. complete as per the specification and direction of the Engineer-in- charge |
| 33 | RCC M-25 Grade in using 20mm downgraded size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts including frame works including cost, conveyance of all maaterials, cost of labour etc. complete as per the specification and direction of the Engineer-in- charge In foundation |
| 34 | In wall |
| 35 | Supplying, fabricating welded water tight drainage spout as per technical specification clause 2705 of specification road and bridge work MORT&H (5th revision) assembly to dimensions shown on drawing of dia not less than 100mm with galvanized steel conforming to IS 226 & fixing in position with suitable fixtures at specified locations on bridge decks including painting two coats with bituminous paint sealed with sealant as per IS 1834 around the spout to the deck slab including full compensation to all operations, all inclusive costs, contigencies, incidental involved for the finished defect free item of work complete as per the specification & direction of the Engineer in charge |
| 36 | Providing, laying and fixing in position reinforced cement concrete 1000mm dia NP4 hume pipes for culverts on first class bedding of granular materials including pointing ends fixing collars with cement mortar 1:3 for finished item of work as per Section 1000 & 2900 of specifications for road and bridge works of Ministry of Road Transport & Highways (5th Revision) & including cost of all materials, labour, T&P, taxes, royalty etc complete in all respect and as per direction of the Engineer-in-charge. |
| 37 | Filling Foundation & plinth with excavated earth by mechanical means including all cost, conveyance, T&P, labour required for the work etc. complete as per drawing & technical specifications for Road & Bridge works MoRTH (5th revision) and as per direction of the Engineer in charge |
| 38 | Providing and erecting a \"W\" metal beam crash barrier comprising of 3mm thick corrugated sheet metal beam rail, 70 cm above road/ ground level, fixed on ISMC series cnanel vertical post, 150x75x5mm spaced 2m centre to centre, 1.8m high, 1.1m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150x75x5mm, 330mm long complete as per clause 810 of MORT&H specifications for Road & Bridge works(5th Revision). |
| 39 | Providing and fixing of retro-reflectorised raised pavement markers of approved colour, quality and make conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing of position with approved quality adhesives including cost of all materials, labour, transportation, taxes duties, sundries, T&P etc complete as per specification and direction of Engineer in charge. |
| 40 | Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflect rising glass beads @ 250gms per sqm area thickness of 2.5mm is exclusive of surface applied glass beads as per IRC-35. The finished surface to be level, uniform and free from streaks and holes etc complete as per specification and direction of Engineer in charge |
| 41 | Providing & fixing RCC M-15 in Hectometer stone, 5th Km. stone and Ordinary Km. stone etc along with reinforcement complete as per drawing as per IRC -25 / 1967 & IRC-8-1980 fixed in position including finishing and ettering, painting and technical specification as per Clause No. 804 & 806 and Section 1000, 1500, 1600, 1700, 2300 of Specification for Road & Bridge works of Ministry of Road Transport & Highways (5th Revision) including cost of all materials, labour, T&P, taxes, royalty etc complete in all respect and as per direction of the Engineer-in-charge.5th Kilometre stone |
| 42 | Oridinary Kilometre stone |
| 43 | Providing and fixing of retro-reflectorised cautionary mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting vide Clause No.801.3 of specifications for road and bridge works of Ministry of Road Transport and Highways (5th Revision) fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle iron post 75mmx75mmx6mm, firmly fixed to the ground by means of properly designed foundation with M-25 grade cement concrete 45cmx45cmx60cm, 60cm below ground level as per approved drawing and including cost of all materials, labour, TandP, taxes, royalty etc complete in all respect and as per direction of the Engineer in charge.Information sign 80 x 60 rectanglar |
| 44 | 60 x 40cm rectangular |
| 45 | 60 x 60cm square (Chevron marker) |
| 46 | 90 x 30 cm rectangulaar |
| 47 | 90 cm equilateral triangle |
| 48 | 90cm high octagon |
| 49 | 60 cm Circular |
| 50 | Direction and place Identification Signs upto 0.9 sqm. size board - Providing and erecting direction and place identification retro-reflectorised sign as per IRC-67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick with area not exceeding 0.9 sqm. supported on a mild steel single angle iron post 75x75x6 mm firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45x45x60 cm, 60cm below ground level as per approved drawing |
| 51 | Direction and place Identification Signs more than 0.9 sqm. size board - Providing and erecting direction and place identification retro-reflectorised sign as per IRC-67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick with area not exceeding 0.9 sqm. supported on a mild steel single angle iron post 75x75x6 mm firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45x45x60 cm, 60cm below ground level as per approved drawing More than 0.9 sqm Please Enable Macros to View BoQ information |
