|
| 1 | Taking down carefully aluminium conductor/Copper conductor point wiring (light,fan,socket or power) completeincluding fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing(except those to be reused shall be kept in safe custodyat the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified and directed. |
| 2 | M & L for concealed point wiringcomplete with 1.5 sq mm FRLSH ,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and WITHincludingofFRLSH PVC insulated 1.5 sq mm copper conductor for earth continuity (Green Colour)and connected to common earth dolly and including pressed steel terminal flush boxesmade out of 1.6 mm thick MS sheet suitable for modular switches concealed in wall , with and includingmodular cover plate with frame for housing the switches socket,outlet etc.,all as specified and directed by Engineer-in-Charge for one light point controled by one one way 5/6 Amp switch Note:-(a) Note :- Cost of PVC conduit, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate. |
| 3 | Allas per ItemNo 2 here-in- before but for onecalling bellpoint controlled by one one way Bell switches complete all as specified and directed.. |
| 4 | All as per item No. 2 here-in- before but5 Amp socket on same boardwith other switches complete all as specified and directed.. |
| 5 | All as per BOQ item No 2.00 here-in-beforebut for one power pointtusing by2.50 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 2.50 sq mmconductor for earth continuity (Green Colour) , on independent board( but Not below the switch board of light points in the same vertical plane). |
| 6 | All as per BOQ item No 2.00 here-in-beforebut for one power pointtusing by4.00 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 4.00 sq mmconductor for earth continuity (Green Colour) , on independent board( but Not below the switch board of light points in the same vertical plane). |
| 7 | Supply & Fixing switch modular type 6 Amp one way, one module, single phase, complete all as specified and directed. (Note : Item to be measured if executed under new point wiring) |
| 8 | S&F socket outlet 5 Amps, 5 pin, modular type, 2 module , single phase with shutter complete all as specified and as directed. (Note : Item to be measured if executed under new point wiring) |
| 9 | Supply & Fixing switch modular type 15/16 Amp one way, two module, single phase, complete all as specified and directed.(Note : Item to be measured if executed under new point wiring) |
| 10 | S&Fsocket outlet15/16 Amps,6 pin, modular type, 2 module , single phase shutter typed complete all as specified and as directed. (Note : Item to be measured if executed under new point wiring) |
| 11 | Supply & Fixing bell push ,modular type 6 Amp SP one way, 1 module , complete all as specified and as directed.(Note : Item to be measured if executed under new point wiring) |
| 12 | Supply & Fixing fan regulator modular step type 120 W 2 module suitable for 230 volt .cmplete all as specified and as directed. (Note : Item to be measured if executed under new point wiring) |
| 13 | Material & Labour forpoint wiringcomplete with 1.5 sq mm FRLSH, PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including PVC casing- caping (double interlock type) ofnot less than 20mm width with accessories and fittingssuch as bends, elbows, tees, crosses, junction box etc, fixed on wall/ceiling with GI saddles, GI screws, rawl plugs etc. for one light/fan/ bell point controlled by one switch including pressed steel terminal box powder coatedof suitable size with 3 mm thick plastic laminated sheet cover of approved make for housing/mounting switches, sockets & regulators etc. and drawing1.5 sq. mm copper solid conductor PVC insulated, unsheated cable as earth continuity conductor, connected to common earth and earth dolly , all as specified and directed by Engineer-in-ChargeNote :- Cost of PVC casing & capping, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.(ii) Length of point wiring up to 7.50 meter and to be measured from switches to ceiling rose or to the actual load. |
| 14 | Allas per ItemNo 13 here-in- before but for onecalling bellpoint controlled by one one way Bell switches. |
| 15 | All as per item No.13 here-in- before but5 Amp socket on same boardwith other switches. |
| 16 | All as per BOQ item No 13.00 here-in-beforebut for one power pointtusing by2.50 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 2.50 sq mmconductor for earth continuity (Green Colour) , on independent board( but Not below the switch board of light points in the same vertical plane). |
| 17 | All as per BOQ item No 13.00 here-in-beforebut for one power pointtusing by4.00 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 4.00 sq mmconductor for earth continuity (Green Colour) , on independent board( but Not below the switch board of light points in the same vertical plane). |
| 18 | Supply and fixed switch piano flush type, single pole , 5/6 Amps, one way complete all as specified. (Note : Item to be measured if executed under new point wiring) |
| 19 | Supply & Fixingsocketoutlets 2 in 1, 5/6 Amps, 230/240 V complete all as specified and as directed .(Note : Item to be measured if executed under new point wiring) |
| 20 | Supply and fix switch socket combination 2 in 1 multipurpose5 pin ,(6 Amps ) flush typecontrolled by one switch complete all as specified. (Note : Item to be measured if executed under new point wiring) |
| 21 | Supply and fixed switch socket combination5 in 1 , 6 pin ,(5/16 Amps ) flush typecontrolled by one switch complete all as specified. (Note : Item to be measured if executed under new point wiring) |
| 22 | Supply & fixed ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified. (Note : Item to be measured if executed under new point wiring) |
| 23 | Supply & fixed stepped type electronic fan regulator flush type 240 Volts ISI marked complete all as specified . (Note : Item to be measured if executed under new point wiring) |
| 24 | Supply & fixed Bell push , flush type , 5 amp complete all as specified. (Note : Item to be measured if executed under new point wiring) |
| 25 | Supply & fixed Buzzer, Ding dong, AC 230 Volts, single pole 230 volts all as specified and directed. (Note : Item to be measured if executed under new point wiring) |
| 26 | Supply & fixed lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified. (Note : Item to be measured if executed under new point wiring) |
| 27 | Supply and fixing for concealedtype sub main wiring with two run of 4.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and includingthrough Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxesetc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc.including one run of 4.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified.Note : (i) Note : 2 runs of line conductor,one run of earth continuity conductor, one run of PVCconduit shall be measured as unit length. (ii)Cost of PVC conduit, conductors,making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate. |
| 28 | All as per BOQ item No 27.00 here-in-beforebut with two run of 6.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) and one run of 6.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) |
| 29 | Supply and fixing for surfacetype sub main wiring/circuit wiring with two run of 4.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including drawn into and including PVC casing- caping (double interlock type) ofnot less than 25mm width with accessories and fittingssuch as bends, elbows, tees, crosses, junction box etc, fixed on wall/ceiling with GI saddles, GI screws, rawl plugs etc. including one run of 4.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified.Note : (i) Note : 2 runs of line conductor,one run of earth continuity conductor, one run of PVCcasing caping shall be measured as unit length. (ii)Cost of PVC casing caping, conductors,making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate. |
| 30 | All as per BOQ item No 29.00 here-in-beforebut with two run of 6.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) and one run of 6.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) |
| 31 | S & Fin repair LED street/security lights nominal power 60 Watt, LED of Make Osram; Everlight; Philips; Nicha; Cree; Samsung, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, lumenefficacy of minimum 110 lumens per watt, built-in integrated electronic LED driver, output open /short circuit protection, phase to phase protection, over voltage protection, surge voltage protection upto 4 KVs, protection grade IP 66, CRI greater than 80%, CW available CCT of 5700K, power factor of minimum 0.95, pressure die-cast aluminium alloy housing with epoxy powder coated metallic silver finish after phosphochromate treatment, life span of minimum 50000 working hoursincluding fixing at any height and including wiring using three core PVC insulated, PVC sheathed, flexible stranded copper conductor FR-LSH cables suitable for outdoor use, 1.5 sqmm as per IS 694: 2010 complete all as specified and as directed. |
| 32 | Taking down existing panel light fitting any type (600 mm x 600 mm) recess mounting/surface and S&F LED light fitting 36 watt recess mounting of size 600 mm x 600 mm , , LED wattage of minimum 3 watt each and Maximum 5 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz,lumen efficacy of minimum 115 lumens per watt, isolated electronic LED driver (SMPS based constant current supply) with output short circuit protection, over voltage protection, surge voltage protection upto 2 KVs, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, ITHD below or less than 15%, WW available CCT of 3000K power factor of minimum 0.95, CRCA powder coated white after phosphochromate treatment housing, life span of minimum 50000 working hours including making electric connection from source with PVC sheathed copper conductor wire of 1.5 Sqmmx 3 core complete all as specified and directed by EIC. |
| 33 | S&F in repairs LED 20 Watt tube light fittingintregatedtype, includingLED retrofit tubelamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with polycarbonate housing and polycarbonate diffuser complete fittingincluding connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fittingcomplete all as specified & directed..Note (i) Make of batten and LED tube lamp should be of same make. |
| 34 | S&F in repairs LED 20 Watt tube light fittingintregatedtype, includingLED retrofit tubelamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fittingincluding connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fittingcomplete all as specified & directed..Note (i) Make of batten and LED tube lamp should be of same make. |
| 35 | Supply & fixing in repair LED light fitting 12 watt surface mounted round extruded aluminium housing down lighter with superior light output as per existing size and shape ,LED wattage of minimum 3 watt each and Maximum 5 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz,lumen efficacy of minimum 110 lumens per watt, isolated electronic LED driver (SMPS based constant current supply) with output short circuit protection, over voltage protection, surge voltage protection upto 2 KVs, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, ITHD below or less than 15%, CW available CCT of 5700K, power factor of minimum 0.95, CRCA powder coated white after phosphochromate treatment housing, life span of minimum 50000 working hours including making electric connection from source with PVC sheathed copper conductor wire of 1.5 Sqmmx 3 core complete all as specified and directed by EIC. |
| 36 | S&F in repairs LED 9/10 Watt tube light fitting mirrorintregatedtype, includingLED retrofit tubelamp 9/10 W , LED tube light nominal power 9/10 Watt, L LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 115 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battenslife span of minimum 50000 working hours complete fittingincluding connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fittingincluding taking down old unserviceable complete all as specified & directed.. Note : Make of batten and LED tube lamp should be of same make. |
| 37 | Supply and fixing in repairSurface Spotlight LED 7W 3000K/4000K with aluminum structure, available with adjustable light engine swivel type 240V AC Lumen efficiency 70lm/W complete all as specified and directed. |
| 38 | Fixing only LED Flood light fitting 70Watt 230 V AC outdoor typecomplete all as specified and directed.Note : Flood light will be issued under Sch B free for fixing only. |
| 39 | S&F in repairs Post Top lantern LED type 36/40 watt 230volt outdoor typewith decorative post top for 360degree indirect light IP 65 Protection with impact and corrosion resistant suitable for service bracket dia 40mm GI pipe complete with all accessories including connected with twin core twisted flexible copper conductor of suitable sizecomplete all as specified and directed. |
| 40 | S & F in repairs LED bollards light 9W/10w for pathways and garden with aluminium extrusion UV stabilised injection moulded opal polycarbonate diffuser for spotless lightening with IP65 including foundation protection. |
| 41 | Assembling and Hanging only ceiling fan (M.D.supply) and connecting up including provision of cable from ceiling rose or connector to fan including Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and as directed. Note : Ceiling fan including blade, rod and canopy will be issued under Sch B free for hanging/fixing only |
| 42 | Fixing only in repairs exhaust fan (M.D. supply) with necessary bolts (6 inches long, 6 mm dia.) with nuts and washers for fixing the fan in wall including making necessary electric connectionfromceiling rose to the fan with PVC insulated flexible cord copper of size 0.75 sqmm and removing fan and blades to store complete all as specified and as directed. Note : Exhaust fan including louvers will be issued under Sch B free for hanging/fixing only |
| 43 | Fixing only in repairs exhaust fan (M.D. supply) made of sturdy Engineering plasticwith necessary bolts including making necessary electric connectionfromceiling rose to the fan with PVC insulated flexible cord copper of size 0.75 sqmm and removing fan and blades to store complete all as specified and as directed. Note : Exhaust fan including louvers will be issued under Sch B free for hanging/fixing only |
| 44 | S & F in repairs sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match asthe existing withall as specified and directed by Engr-in-charge. |
| 45 | S & F in repairs sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 12 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match asthe existing withall as specified and directed by Engr-in-charge. |
| 46 | S & F in repairs sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 8 way single door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 30 , IK 08 including fixing the DB box flush in wall of any type and making good the distrubed surface to match asthe existing withall as specified and directed by Engr-in-charge. |
| 47 | S & F in repairs sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way single door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 30 , IK 08 including fixing the DB box flush in wall of any type and making good the distrubed surface to match asthe existing withall as specified and directed by Engr-in-charge. |
| 48 | Supply and fixing in repairs MCCB 4 Pole 100 Amps Breaking Capacity 16KA ,415V to be housed in DBs complete including necessry connectionall as specified and directed engr-in-charge |
| 49 | Supply and fixed inMCB TPN 40 to 63 Amps,\"C\" Curve 10kA, 415 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed engr-in-charge. |
| 50 | Supply and fixed MCB SPN 32 Amps,\"C\" curve 10kA, 240 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed engr-in-charge. |
| 51 | Supply and fixed MCB SP 6-32 Amps,\"C\" curve 10kA, 240 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed engr-in-charge. |
| 52 | Supply and fixing in repair of 20Astarter switch for AC including necessary connection all as specified and directed engr-in-charge. |
| 53 | Supply & Fixing in replacement of \"Modular AC Box With 20A SP MCB, Plastic Enclosure & Unbreakable Heavy Duty With ISI Plug Top\", complete all as specified and directed. |
| 54 | S&F sheet metal enclosure (Plug & Socket) with 20 Amp Mcb and two pin and earth plug and socket complete with one single pole MCB complete all as specified and as directed. |
| 55 | Supply and installed voltage stabilizer 17.6 Amp wall mounting type for automatic operation, single phase, naturally air cooled indoor type and designed for input variation between 130 V to 280 with out put voltage stabilized at 200 V to 230 V accuracy of + 2.0%, copper wound complete all as specified |
| 56 | Supply, Installation, testing and commisioning of split type Air Conditioner of capacity 1.5 TR with hermitically sealed unit complete with dual system i.e cooling and with PCB and remote operationon (R-410A refrigerant) built in air ioniser S&F wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity 1.5 TR, ISI marked single phase, 240 volts complete all as specified and as directed |
| 57 | Material andlabour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mmmm buried directly in ground (Earthpit not less than2.25m below ground level) with top edge of theplate not less than 1.5m below normal groundlevel, connected to GI wire 4 mmasearth lead by means of bolt, nuts, check nutsandwashers of galvanised iron or steel, upto 7.5mlength, earth strip protected by andincluding 15 mm diaGI pipe (medium grade) andconnected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC(1:3:6)type C1 , Precast RCC(1:2:4)TypeB1 coverslab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100mm C/C bothwayswith onehandle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm boreGI Pipe (Medium Grade) for watering, Charcoal andsalt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any typeof soil anddisposal of spoil to a distance n.exc50 m andnecessary testing complete all asshown in Electrical Plate No 3 of SSRPart-I.NOTE : 1. The unit rare includes for protectionh GI pipe of 15mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wireincluding protection pipe,from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate |
| 58 | Supply and fixed in repair D clamp of strip size 25x6 mm with suitable washer,nuts, bolts in any shape or size as indicated or directed including making hook for hanging ceiling fan and inclusive of one primer coat ,one under coat, one finish coat of paint complete for hanging of ceiling fan all as specified and as directed. |
| 59 | S & Fin repair LED street/security lights nominal power 35/36 Watt, LED of Make Osram; Everlight; Philips; Nicha; Cree; Samsung, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, lumenefficacy of minimum 110 lumens per watt, built-in integrated electronic LED driver, output open /short circuit protection, phase to phase protection, over voltage protection, surge voltage protection upto 4 KVs, protection grade IP 66, CRI greater than 80%, CW available CCT of 5700K, power factor of minimum 0.95, pressure die-cast aluminium alloy housing with epoxy powder coated metallic silver finish after phosphochromate treatment, life span of minimum 50000 working hoursincluding fixing at any height and including wiring using three core PVC insulated, PVC sheathed, flexible stranded copper conductor FR-LSH cables suitable for outdoor use, 1.5 sqmm as per IS 694: 2010 complete all as specified and as directed. |
| 60 | S&F recess mounting luminaire (PANEL LIGHTING) with high performance LEDs, suitable for mounting withArmstrong/Grid ceiling Fixture size: (LxW) in (600 x 600) mm LED 36 Watt with CRCA powder coated housing (white after phosphochromate treatment) High efficiency long life LED package in integral module with lumen efficacy of >120 lm/W and viewing angle of 120° to ensure better uniformity, electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test as per IS:15885 Part 2/Sec 13. operational voltage of 170 volts to 270 volts, frequency of 50 Hz,protection grade IP 20, CRI greater than or equal to 80%,THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 , life span of minimum 50000 working hours complete fittingincluding connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core,including taking down old unserviceable complete all as specified & directed: |
| 61 | Supply & Fixing in replacement switch modular type 6 Amp one way, one module, single phase, complete all as specified and directed. |
| 62 | S&Fin replacement socket outlet 5 Amps, 5 pin, modular type, 2 module , single phase complete all as specified and as directed engr-in-charge. |
| 63 | Supply & Fixing in replacement switch modular type 15/16 Amp one way, two module, single phase, complete all as specified and directed. |
| 64 | S&Fin replacement socket outlet 15/16 Amps, 5 pin, modular type, 2 module , single phase complete all as specified and as directed engr-in-charge. |
| 65 | Supply & Fixingin replacement fan regulator modular step type 120 W 2 module suitable for 230 volt .cmplete all as specified and as directed engr-in-charge. |
| 66 | Supply and fixed in replacementswitch piano flush type, single pole , 5/6 Amps, one way complete all as specified engr-in-charge. |
| 67 | Supply & Fixing in replacementsocketoutlets 2 in 1, 5/6 Amps, 230/240 V complete all as specified and as directed engr-in-charge. |
| 68 | Supply and fix in replacementswitch socket combination 2 in 1 multipurpose(6 Amps ) flush typecontrolled by one switch complete all as specified engr-in-charge. |
| 69 | Supply and fixed in replacementswitch socket combination5 in 1 (5/16 Amps ) flush typecontrolled by one switch complete all as specified engr-in-charge. |
| 70 | Supply & fixed in replacementstepped type electronic fan regulator flush type 240 Volts ISI marked complete all as specified engr-in-charge. |
| 71 | Supply and fixing in replacement of Decorative wall light, gold finish fixture with white glass diffuser suitable for 1 N x9 W LED Lamp/2 N x7.5 W LED filament lamp E27 base complete all as specifed and directed engr-in-charge. |
| 72 | Supply and fixing in replacement of Decorative wall light, stainless steel, rust free fixture with white glass diffuser suitable for Decorative wall light fixture 1 N x 9 W LED Lamp/1 N x 7.5 W LED filament lamp E27 base |
