|
| 1 | Laying and Jointing PVC Pipe. Heading |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas A(exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead uto 50m and lift upto 1.5m, as directed by Engineer-in-charge.Ordinary rock |
| 3 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20cm in trenches, plinth, sides of foundation etc. complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work up to plinth level 1:3:6 ( 1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20mm Nominal size derived from natural sources) |
| 5 | Cement concrete flooring 1:2:4 (1 Cement : 2 Coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate |
| 6 | Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in :Cement mortar 1:6 ( 1 Cement : 6 coarse sand) |
| 7 | Half brick masonry with common burnt clay F.P.S (non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.” Cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 8 | 12mm Cement plaster of mix : 1:6 (1 cement : 6 fine sand) |
| 9 | Neat cement punning |
| 10 | Centering and shuttering including strutting, propping etc. and removal of from for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 11 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level :1:2:4 ( 1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 12 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all compete above plinth level. Thermo-Mechanically treated bars of grade Fe-500D |
| 13 | Providing and laying Ceramic Glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality confirming to IS : 15622 of approved make in colours such as white, Ivory, Gre, Fume Red Brown , laid on 20mm thick cement mortar 1:4 (Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 14 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified b the manufacturer) of approved make, in all colours, shades except burgundy, bottle green, black of any size e as approved by Engineer-in-charge, in skirting, risers of stepsand dados, over 12mm thick bed of cement mortar 1:3 (1 Cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in cement mixed with pigment of matching shade complete. |
| 15 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, of required shade and colour Complete as per manufacturer’s specification Two or more coats on new work Finishing walls with Acrylic Smooth exterior paint |
| 16 | New work (Two or more coat applied @ 1.67 ltr/10sqm over and including priming coat of exterior primer Applied @ 1.20kg/10sqm) |
| 17 | Structural steel work riveted, bolted or welded in built up suctions, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 18 | Providing corrugated G.S. Sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G>I limpet washers or with G.I limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete *up to an pitch in horizontal/vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63mm thick with zinc coating not less than 275gm/m3 |
| 19 | Door & Ventilation Work |
| 20 | Providing and fixing factory made P.V.C door frame of size 50x47 mm with awail thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet, mitered at comers and joined with 2 Nos. of 150mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge. |
| 21 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S. Frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat molded PVC “C” channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm thickness, 70mm width out of which 50mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5mmthick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail paneling of 5mm thick of side PVC sheet to be fitted in the M.S frame welded/sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the “C” Channel using PVC solvent adhesive etc. Fitted in the M.S. frame welded/sealed to the styles & rails with 7mnm (5mm+2mm) thickx15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the “C” Channel using PVC solvent adhesive etc. compete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. 30mm thick pre laminated PVC door shutters |
| 22 | Providing and fixing ISI marked oxidized M.S door latches conforming to IS:5930 with screws etc. complete: 300x20x6mm |
| 23 | Providing and fixing ISI marked oxidized M.S. handles conforming to IS:4992 with necessary screws etc. Compete : 125mm |
| 24 | Providing and fixing factory made IUSI marked steel glazed doors, windows and ventilators, side/top/center hung, with beading and all members such as F7D, F4B, K11 B and K12B etc. Complete of standard rolled steel sections, joints mitered and flash butt welded and such bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10cm of C.C. 1:3:6 ( 1Cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) |
| 25 | Providing& fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all Complete with : 4.0mm thick glass panes |
| 26 | Sanitary fittings/Water Supply and electrical fittings |
| 27 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making Good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. |
| 28 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:15mm nominal bore |
| 29 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:15mm nominal bore |
| 30 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:15mm nominal bore |
| 31 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:15mm nominal bore |
| 32 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106cms. |
| 33 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms. |
| 34 | Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 35 | Providing and fixing PTMT grating of approvedQuality and colour. 100mmnominal dia |
| 36 | Providing and fixing wash basin with C.I brackets, 15 mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. White Vitreous China Wash basin size 630x450mm with a pair of 15mm C.P. brass pillar taps |
| 37 | Providing and fixing P.V.C waste pipe for sink or washbasin including PVC waste fittings complete Semi rigid pipe 32mm dia |
| 38 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fitting |
| 39 | Constructing soak pit 1.20x1.20x1.20m filled with brickbats including S.W. drain pipe 100mm diameter and 1.20m long complete as per standard design. |
| 40 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow. Pipes but without fittings and the base support for tank |
| 41 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated alminium rod with L.P/H.P.H.D plastic ball 25mm nominal bore, 152mm long, weighing not less than 440gms. |
| 42 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints compete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15mm nominal dia pipes |
| 43 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15mm nominal bore |
| 44 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints. Complete as per direction 15mm nominal dia pipes |
| 45 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints. Complete as per direction of Engineer Charge. 100mm nominal dia Pipes |
| 46 | Providing and fixing of 3 Nos. led bulb with holder & switches, 1 No. 16 amp socket with switch complete connection, 01 exhaust fan (300mmx300mm) with all necessary fitting, electrical wiring & 2.5mm with PVC casing as per direction of engineer in charge. |
