|
| 1 | M&L for maintenance of DG Set 250 KVA DG setand carrying out \"B\" check and replacement/ servicing of \"B\" check kit filters such as oil filter, by pass filter, fuel filter, CR element and CR plates complete with \"O\" rings and draining of Engine oil and topping up with the new engine oil complete testing all as specified and directed by Engr-in-Charge for the following capacity DG Sets : - Note : (i) Necessary tool for replacement of spares for \"B\" check shall be deemed to be inclusive in the rate quoted by the contractor.(ii) Spares such as replacement of u/s items incl engine oil, air filter, fuel filter & mobil filter,or any parts of DG sets will be measured & paid separately under respective item as supply only. (iii) Contractor should visit the site before quoting the tender to know the working condition of the station.All requisite safety measurers are to be adopted by contractor on site. (iv) Minor repair work whereever supply only items by contractor for DG sets is to be carried out by DG Set technician. (v). The contractor will be responsible for cleaning/grass cutting/ vegetation cutting upto two meter surrounding of DG Sets. (vi) Necessary welding work required /replacement of door hings etc any other parts shall be deemed to be inclusive in the rate quoted by the contractor. (vii)Supply & fixing & testing after repair items should be executed thorugh authorized rep of manufacturer only and fixing charges to be inclusive in the rate quoted by the contractor mentioed in below respective capacity of DG sets. |
| 2 | Supply only following spare parts as mentioned at Sl No. 1.00 above for 250 KVA DG set above:- |
| 3 | Spinion Lub Oil filter |
| 4 | Fuel Filter kit 1.1 ltr |
| 5 | Centrifugal filter service kit |
| 6 | Safety Air filter element |
| 7 | Oil seal (150x120x13.5) |
| 8 | Oil supply pipe sub assembly (with flex men) |
| 9 | V Belt AVX13X1562L |
| 10 | By pass Hose |
| 11 | Water supply Sub Assembly |
| 12 | V Belt AVX13X1015L |
| 13 | Centrifugal filter service kit |
| 14 | Vent pipe sub assembly |
| 15 | Leak off Pipe Assembly |
| 16 | Fuel pipe fuel filter to feed pump |
| 17 | Battery Cable Assembly |
| 18 | Valve pair inlet &Exhaust |
| 19 | Radiator assembly cleaning & Silencer decorbonising |
| 20 | Description all as per Sl No 1.00 above here-in-before but for 100 KVA DG Set |
| 21 | Supply only following spare parts as mentioned at Sl No 1.00 above for 100 KVA DG Set above:- |
| 22 | Spinion Lub Oil filter |
| 23 | Fuel Filter (Primary & Secondery) |
| 24 | Primary Air filter element |
| 25 | Safety Air filter element |
| 26 | Oil seal (115x140x12) |
| 27 | Oil Seal (65x85x13) |
| 28 | V Belt XPA 1250 Cogged |
| 29 | V belt cogged (BX-48) |
| 30 | By pass hose : 58MM long |
| 31 | Selector switch |
| 32 | Hose pipe Radiator to waterpump 45x45x130L |
| 33 | Hose pipe to waterpump 45x45x80L |
| 34 | Crankshaft assembly with Gear |
| 35 | Vent pipe for Radiator |
| 36 | Leak off Pipe Assembly |
| 37 | Hose water pipe |
| 38 | Fuel pipe 7.5 14x14 B 700 PB |
| 39 | Fuel pipe 8.0 14B 1000WB |
| 40 | Conversion kit from KG 934 to KG 645 |
| 41 | Lube Oil Pressure Sensor |
| 42 | Cylinder head gasket |
| 43 | Battery Cable Assembly 35sqmm |
| 44 | Radiator assembly cleaning |
| 45 | Description all as per Sl No. 1.00 above here-in-before but for 50 to 62.5 KVA DG Set |
| 46 | Supply only following spare parts as mentioned at Sl No. 1.00 for 50 to 62.5 KVA DG Set above:- |
| 47 | Spinion Lub Oil filter |
| 48 | Fuel Filter (Primary & Secondery) |
| 49 | Primary Air filter element |
| 50 | Safety Air filter element |
| 51 | Oil seal (115x140x12) |
| 52 | Oil Seal (65x85x13) |
| 53 | V Belt XPA 1250 Cogged |
| 54 | By pass hose : 58MM long |
| 55 | Selector switch |
| 56 | Battery Charger 12V 6Amp |
| 57 | Hose pipe Radiator to waterpump 45x45x130L |
| 58 | Hose pipe to waterpump 45x45x80L |
| 59 | Mechanical Fuel level sensor assembly |
| 60 | Vent pipe for Radiator |
| 61 | Leak off Pipe Assembly |
| 62 | Hose water pipe |
| 63 | Fuel pipe 7.5 14x14 B 700 PB |
| 64 | Fuel pipe 8.0 14B 1000WB |
| 65 | Conversion kit from KG 934 to KG 645 |
| 66 | Engine Wiring Harness: 6R CPCB complete replace |
| 67 | Battery Cable assembly 35 sqmm |
| 68 | Radiator assembly cleaning |
| 69 | Description all as per Ser No. 1.00 here-in - before but for 25 to 40 KVA DG Set |
| 70 | Supply only following spare parts as mentioned at Sl No. 1.00 for 25 to 40 KVA DG Set above:- |
| 71 | Spinion Lub Oil filter |
| 72 | Fuel Filter 1.1 Ltr |
| 73 | Primary Air filter element |
| 74 | Cyl Head Gasket 1.22 MM Thick |
| 75 | Oil seal (115x140x12) |
| 76 | Oil Seal (65x85x13) |
| 77 | V Belt XPA 1250 Cogged |
| 78 | CON Rod Bearing HA 394 STD |
| 79 | By pass hose : 58MM long |
| 80 | Selector switch |
| 81 | Hose pipe Radiator to waterpump 45x45x130L |
| 82 | Hose pipe to waterpump 45x45x80L |
| 83 | Mechanical Fuel level sensor assembly |
| 84 | Vent pipe for Radiator |
| 85 | Leak off Pipe Assembly |
| 86 | Hose water pipe |
| 87 | Fuel pipe 7.5 14x14 B 700 PB |
| 88 | Fuel pipe 8.0 14B 1000WB |
| 89 | Conversion kit from KG 934 to KG 645 |
| 90 | Fuel tank assembly with accessory |
| 91 | Battery Cable Assembly 35sqmm |
| 92 | Radiator assembly cleaning |
| 93 | Labour only for attending the breakdown/ nonfunctioning of any capacity/make DG sets, AMF panels by deploying one Number Technician & helper for checking all components and rectify the fault and give report to concerned JE complete all as specified and directed by Engr-in-Charge. Note : (i) Spare parts for rectify the fault will be measured and paid separately.(ii) The contractor shall also provide DG Set technician on Sunday & holiday if required or asked by JE E/M/Engineer-in-charge.(iii) If contractor failed to provide their DG Set technician or absent to attend the complaints / minor complaint within 24 Hrs, then the recovery will be effected at Rs 1000.00 per day per complaints. |
| 94 | M&L for replacement of unserviceable auto main failure (AMF) panel of capacity upto 62.5 to 100 KVA capacity DG set includign all internal electrical connections,sensor, ATS switch,DG on /off facility, Busbar, wire, lugs,cable tray, panel box 18 guage thickness etc complete commissioning & testing all as specified and directed by Engr-in-Charge.Note:- Including following spare parts of AMF panel above quoted rate: (a) 160 amp FP pole MCCB -02 Nos, (b) 01 no FP ATS 160 Amp with controller, (c) Spreader link -02 set, (d) 12V/24V battery charger-01 No, (e) Glass Relay-02 Nos, (f) Current Transformer- 125 Amp , 125/5A (g) R,Y,B indicator - 03 Nos, (h) 6 Amp single pole controler MCB-06 Nos, (j) Auxilary Contactor-02 nos. |
| 95 | M&L for drain out old engine oil from DG set/ Vehicle and replace with new Engine oil servo type in 20 Ltrs seal pack 20W/40 & 15W40or as per site requirement. Make : Castrol/HP//Gulf/KOEL Care |
| 96 | M&L for Inhibitor corrosion (coolant additive concerntrate) required for top up complete all as directed by Engr-in-charge |
| 97 | Supply and topping up of acid mixture suitable for lead acid batteries of 12 volts complete all as directed by Engr-in-charge |
| 98 | Supply and topping up of distilled water suitable for lead acid batteries of 12 volts complete all as directed by Engr-in-charge. |
| 99 | M&L for dismantling/opening of Retrofit emmission control device (RECD) exhaust assembly of the DG set with following work to be carried out by contractor without any extra cost.(a) Opening of RECD DPF (Diesel Particulate filetr)(b) Opening of RECD Cladding and refitting the same in original position after complete the work.(c) Cleaning of DPF filter/chamber and exhaust assembly by only CPCB approved device company mechanic ie Chakara Inn.,Platino and Green or any equivlent.(d) Check the back pressure of RECD after cleaning as per CPCB guidlines.(e) Closing the DPF and refixing the same in its original position.(f) Periodic check of Sensors (Temprature and Back pressure sensors).(g) Checking of Control panels and replace any faulty Relay/MCB etc and update the version etc.(h) Cleaning of DPF filter in every six month, like that first is after acceptance of tender with in first week and second is after six month. |
| 100 | 25 to 40 KVA DG Sets (RCED Ser No 1233 & 1234) |
| 101 | 62.5 KVA DG Sets (RECD Ser No 1235 & 1236) |
| 102 | 100 KVA DG Sets (RECD Ser No 1237) |
| 103 | 250 KVA DG Sets (RECD Ser No 1238 & 1239) |
| 104 | M&L for dismantling of exhaust pipe of the DG set by unscrewing nuts and bolts and taking down the pipe with muffler removing the burnt out asbestos rope and replaced with new asbestos rope, well wrapping with new aluminium metal cladding with glass wool including cleaning the silencer, welding if required, painting and refixing the same in its original position complete all as directed by Engr-in-charge for the following capacity DG sets :- |
| 105 | 25 to 40 KVA DG Sets |
| 106 | 50/62.5 KVA DG Sets |
| 107 | 100/125 KVA DG Sets |
| 108 | M&L for Canopy Restoration & Painting of DG set by scrapping of old paint complete and painting with two coats ofAspa super finish paint/as per exisitng colour/makewith spray pump applying before polyplaster automativeputty on rusted/scratch area of fwg capacity of DG sets complete all as specified & directed. |
| 109 | 25 to 40 KVA DG Sets |
| 110 | 50/62.5 KVA DG Sets |
| 111 | 100/125 KVA DG Sets |
| 112 | M&L for replacement of lead acid battery of cap 150 AH, 12V, complete all as specified and directed. Make : Exide New Xpress or its equivalent Amaron/Luminous |
| 113 | M&L for repair/Replacement of unserviceable automatic voltage regulator (AVR) of capacity upto 25 to 100 KVA capacity DG set includign all internal electrical connections, testing all as specified and directed by Engr-in-Charge. |
| 114 | M&L for dismantling of old unservicable door lock with catcher& replace with new LH/RH lock with catcher for canopy of DG set any capacity including welding work if required refixing the same in its original position complete all as specified & directed by Engr-in-charge. |
| 115 | M&L for dismantling of old unservicable door hinges & replace with new SSLH/RH hinges for canopy of DG set any capacity including welding work if required refixing the same in its original position complete all as specified & directed by Engr-in-charge. |
| 116 | M&L for replacement of existing earthing complete with galvanized iron or steel plate electrode 600 mm x 600 mm x 6.00 mm thick buried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal andcommon salt in alternate layers and electrode connected to galvanized iron strip 32 x 6 mm dia as earthing lead by means of GI bolts, nuts, check nuts and washers, earth strip protect0ed by galvanized steel pipe 40 mm bore (light grade) connected to machinery/ equipment all as shown in electrical plate No. 3 of SSR-2010 Part I and including necessary excavation and earth work in any type of soil, 20mm bore light grade GI pipe for watering, funnel, wire mesh, PCC (1:3:6) type C-1 chamber, MS cover of thickness 5mm openable type and having suitable locking arrangementand MS frame of suitable size made of angle iron 50 x 50 x 60 mm, complete all as specified. Note: (i) The unit rate includes earth lead and protection pipe up to maximum 7.5 metre from earth plate to earth point/test point. (ii) Earth pit shall be constructed minimum 0.5 metre away from earth. |
| 117 | Supply and fix in replacement of Galvanised iron strip 32x6mm burried in the ground/pipe/wall and dully connected to machinery with nuts bolts washers and thimbles complete all as specified and directed. |
| 118 | M&L for lifting the Gen Set of capacity62.5 to100KVA after disconnection complete from cables, shifting to other place whereever directed by engr-in-charge and making PCC foundation of size suitable to existing DG set with 1:2:4 including smooth finishing, shifting of DG set on new foundation with all necessary arrangement of cable connections, testing and commissioning complete all as directed by Engr-in-charge. Note : All items, manpower including crane for lifting up and placing again on new foundation is included in quoted rates. |
| 119 | Taking down of existing canopy of DG set 62.5 KVA and S&F new Acoustic enclosure (Canopy) of 62.5 KVA DG set fabricated with 2mm thick CRCA sheet as per existing size of DG set . The noise level shall be 75 dBA or better at a 1 meter from the canopy surface confirming to environmental (Protection) rules issued by CPCB, Govt of india.The following Feature of the Product is as under complete all as specified.(i) Rust/Corresion free.(ii) Proper design as per existing (iii) Noise control as per CPCB(iv) Proper Air intake and Exhaust system(v) Provide Stailess steel heavy duty locks and Hinges with 04 Nos Door.(vi) Powder coated finish as per existing colour.Note :- All items, manpower including crane for lifting up and placing again on new/existing foundation, connection/disconnection of cable is included in quoted rates. |
| 120 | M&L for in replacement of XLPE insulated, screened, PVC shethed, galvanised steel strip or wire armoured heavy duty electric power cable 1100 volts with stranded aluminium conductor of size 95 Sqmm 3.5 core laid in trenches or under road including jointing and testing complete all as specified and as directed. (Note: Excavation, cable protection work will be measure & paid separately) |
| 121 | All as per serial item No: 26 here-in- before but of size 120 Sqmm 3.5 core. |
| 122 | Excavation in trenches not. exc. 1.5m wide and not exc. 1.5 in deep and getting out in soft/loose soil complete all as specified and directed. |
| 123 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soft/loose soil. |
| 124 | Removing surplus soil to a distance not exc 50m and depositing where directed at a level not exc. 1.5m above the starting point. |
| 125 | Supply, laying & fixing double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps as size of DWC pipe is 63mm O/D and 50 mm Inner dia allas specified and directed by Engr in Charge. |
| 126 | EICHER CANTER Comprehensive maint and servicing, oiling, Hub greasing, tuning, overhauling fixture accessories replacement of first moving parts changing oil/fuel filters, replacement of bulbs, fuses, replacement of coolant, brake oil, stearing oil, engineoil,cleaningandmaintofradiators,maintofbatterywithelectrolyte solution,distilledwater,wheelalignment,cleaningoffueltankcompleteallas directed.Note : Major repairs, major spare parts shall be measured and paid seperately. |
| 127 | Supply only following spare parts of vehicle as mentioned at Sl No 32.00 above:- |
| 128 | Fuel filter (Primery & Secondry). |
| 129 | Oil Filter |
| 130 | Air Filter |
| 131 | Tail light assy |
| 132 | Fan Belt |
| 133 | Wiper motor |
| 134 | Wiper arm with rubber blade |
| 135 | Repair/servicing/cleaning of raditor for cooling finns core tubes bottom and upper tank leakage if any found. |
| 136 | Side mirror |
| 137 | Foot mat |
| 138 | Horn |
| 139 | Head light assy (Left & Right) |
| 140 | Cabin light |
| 141 | Indicator light assy (Left & Right) |
| 142 | Grease |
| 143 | Repair andoverhauling ofhydraulic/telescopic ladder systemandcheckingof all parts suchasreturn filter, suction filter,all type control valve, hydraulic pump, pump seal kit, hydrauliccylinder upper & lower boom seal kit,Hydraulic motor seal kit, Drag chain 1.5 mtr, Boom rest rubber, flexible hose pipe all type, Seamless pipe all sizes, bucket lights, electrical panel box, emergency switch etc complete all as spfd and directed. Note : Major spare parts required shall be measured and paid seperately. |
| 144 | Return Filter |
| 145 | Suction filter |
| 146 | Flexible Hose pipe any size |
| 147 | Hydraulic oil 68 No |
| 148 | Hydraulic pump/motor seal kit |
| 149 | Hydraulic cylinder (upper & lower boom) seal kit |
| 150 | Emergency hand pump packing |
| 151 | Control valve seal kit any type |
| 152 | Repair andoverhauling ofdefective suspension systemandcheckingofparts suchasshockabsorber,front spring leaf, centre bolt, front spring leafhanger, front spring leaf, shackle pin, rear spring leaf, rear spring leaf hanger, rear shackle pin of Eicher veh and complete all as spfd and directed. Note : Major spare parts required shall be measured and paid seperately. |
| 153 | Supply only following spare parts for suspension system for Eicher Veh: |
| 154 | Shock absorber front |
| 155 | Shock absorber bush |
| 156 | Hanger front |
| 157 | Hanger rear |
| 158 | Ball Joint |
| 159 | Load Spring various size |
| 160 | Tensioning the road springuptotherequired and original position and assembling the same with nuts,centerboltandclamps-04Nosandbushes complete all as specified and directed |
| 161 | Repair and overhauling of defective brake system and checking of parts such as front disc brake, rear wheel cylinder, master cylinder, rear brake shoe, front disc brake pad, frontdiscbreakcaliper assembly completebrake pipe,rear wheel brake shoe spring & locking assembly and testing complete all as specified and as directed. Note : Major spare parts required shall be measured and paid seperately. |
| 162 | Supply only following spare parts for braking system mentioned in item ser No 37.00 above: |
| 163 | Front brake disc |
| 164 | Rear wheel cylinder kit |
| 165 | Rear brake shoe |
| 166 | Pressure plate |
| 167 | Rear wheel brake shoe spring & locking assembly |
| 168 | Clutch plate |
| 169 | M&L for repair and Calibration of FIP and governor by replacing pump elements, deliveryvalve,plugs,springs,gasketssleeves,washersfiltersetcandtesting complete of Eicher. |
| 170 | M&L for repair to self starter by replacing damaged,Armature winding, pinions springs etc complete incl rectifications of electric wiring of the engine complete of Eicher veh all as directed. |
| 171 | M& L forrepair/rewinding of unsv alternator (dynmo) of Veh Eicher Canter complete all as specified and directed. |
| 172 | MOTOR CYCLE HERO HONDA /HF DELUXEComprehensive maint and servicing, washing, oiling, greasing, tuning, overhauling fixture accessories replacement of first moving parts changing oil/oil filters,replacementofbulbs,fuses,repairingofwiring,maintofbatterywith electrolyte solution, distilled water complete all as directed. Note : Major repairs, major spare parts shall be measured and paid seperately. |
| 173 | Supply only following spare parts of vehicle as mentioned at item Sl No 42.00 above :- |
| 174 | Speedometre cable |
| 175 | Spark plug |
| 176 | Indicator Assy front side |
| 177 | Indicator Assy rear side |
| 178 | Horn Assy |
| 179 | Oil Filter |
| 180 | Chain Spocket |
| 181 | Clutch/Race cable |
| 182 | Chain with revet |
| 183 | Side mirror |
| 184 | Front light assy complete |
| 185 | Rear light assy complete |
| 186 | Repair and overhauling of defective shocker system of motor cycle and carry out the repair including replacement of the defective spare parts and assembling the same and testing complete all as specified and as directed. Note : Major spare parts required shall be measured and paid seperately. |
| 187 | Supply only following spare parts for shocker system of motor cycle :- |
| 188 | Rear shocker |
| 189 | Oil pump in built front shocker |
| 190 | hydraulic oil |
| 191 | Shock Absorber |
| 192 | Repair and overhauling of defective brake system of motor cycle, replacement of defectivesparepartlike brake shoe etc andassemblingthesamewithtestingcomplete allas specified and as directed. |
| 193 | Takingoutoldseatcoverandfixingnewseatcover(completeset of motor cycle) after necessary repair of original seat and cushion by stitching the worn out seat,fitting seatmaterialsofgoodqualityandfixingthesametotheirproperplaceneatly complete all as specified and as directed. |
| 194 | Dismantlingandtakingdownthegearboxof MC repairandoverhaulingincluding replacementof worn spare partsand testing completed allas specifiedand as directed. |
| 195 | M & L for repair /rewinding of unsv altornator (dynmo) MC self starting type system defected any type complete repair deemed to be quoted rate complete allas specified and directed. |
| 196 | MARUTI DZIRE (STAFF CAR)Comprehensive maint and servicing, washing, oiling, greasing, tuning, overhauling fixture accessories replacement of first moving parts changing oil/oil filters,replacementofbulbs,fuses,repairingofwiring,maintofbatterywith electrolyte solution, distilled water complete all as directed. Note : Major repairs, major spare parts shall be measured and paid seperately. |
| 197 | Fuel filter (Primary & Secondary) |
| 198 | Oil filter |
| 199 | Air filter |
| 200 | Perfume 250 ml. |
| 201 | Matting complete set. |
| 202 | Computerized alignment and balancing of wheels |
| 203 | Head light with assy (Left & Right Rear) |
| 204 | Head light with assy (Left & Right Rear) |
| 205 | TATA XENON /TATA Mobile 207 DIComprehensive maint and servicing, oiling, Hub greasing, tuning, overhauling fixture accessories replacement of first moving parts changing oil/oil filters,replacementofbulbs,fuses,repairingofwiring,maintofbatterywith electrolytesolution, distilledwaterandreplacingallthemonogramwithnew monogramandletterwritingwithrediumretroletterwritingcompleteallas directed. Note : Major repairs, major spare parts shall be measured and paid seperately. |
| 206 | Supply only following spare parts of vehicle as mentioned at item Sl No. 52.00above :- |
| 207 | Oil Filter |
| 208 | Fuel filter (Primery & Secondry). |
| 209 | Staring cover |
| 210 | Mud flap for veh |
| 211 | Complete set of Matincluding floor mat of the vehicle. |
| 212 | Side mirror |
| 213 | LED foglight complete assy (L+R) |
| 214 | Head light complete assy (L+R) |
| 215 | Indicator light assy (L+R) |
| 216 | Fan Belt |
| 217 | Fuel Tank cleaning |
| 218 | Wiper arms with blade |
| 219 | Wiper moter with pipe & connected items |
| 220 | Air cleaner filter element |
| 221 | Door lock assembly complete set |
| 222 | Horn Assy |
| 223 | Raditor servicing/cleaning incl. repair if any water leakge found. |
| 224 | Computerized alignment and balancing of wheel |
| 225 | Grease |
| 226 | Repair and overhauling of defective brake system and checking of parts such as front disc brake, rear wheel cylinder, master cylinder, rear brake shoe, front disc brake pad, frontdiscbreakcaliper assembly completebrake pipe,rear wheel brake shoe spring & locking assembly and testing complete all as specified and as directed. Note : Major spare parts required shall be measured and paid seperately. |
| 227 | Supply only following spare parts for braking system mentioned in item ser No 54.00 above:- |
| 228 | Front brake disc |
| 229 | Rear wheel cylinder kit |
| 230 | Rear brake shoe |
| 231 | Pressure plate |
| 232 | Rear wheel brake shoe spring & locking assembly |
| 233 | Clutch plate |
| 234 | Repair and overhauling of defective shafting system and checking of parts such as propeller shaft, centre bearing, centre bearing clamp and rubber pad, universal cross, yok, teeth and testing of Tata Mobile/Xenon/Eicher complete all as directed.Note : Major spare parts required shall be measured and paid seperately. |
| 235 | Supply only following spare parts for shafting system mentioned in above item no 56.00:- |
| 236 | Centre bearing |
| 237 | Tie rodwith end set |
| 238 | Centre bearing clamp |
| 239 | U J Cross bearing |
| 240 | Repair and cleaning of defectivesilencer assembly including necessary cutting, welding, cleaning andassembling complete of Tata Mobile/Eicherall as specified and directed. Note : Major spare parts required shall be measured and paid seperately as supply only. |
| 241 | Supply only following spare parts for Silencer Assembly of Tata Mobile/Eicher as per item ser No 58.00 above :- |
| 242 | Muffler |
| 243 | Manifold |
| 244 | Silencer pipe Assy |
| 245 | Supply andfixingin replacementoftubeless tyreofexisting sizeor as per OEM suitableforMotor cycle andtaking down old cover outer complete all as spd and directed. Make: MRF/ Apollo/ Bridgstone/JK. |
| 246 | Taking out old seat cover and fixing new Leather seat cover (complete set front and back) after necessary repair of original seat and cushion by stitching the worn out seat, fittingseatmaterialsofgoodqualityandfixingthesametotheirproperplace neatly complete of Tata Mobile/Xenon all as specified and as directed. |
| 247 | Dismantlingandtakingdownthegearboxofrepairandoverhaulingincluding replacement ofworn spare parts i.e. gear liver kit, Gear pinion 1st, 2nd, 3rd, 4th and 5th and other minor spares andtesting of Tata Mobile/Xenon completed all as directed. |
| 248 | Taking down old unserviceable silencer replace with newsilencer of Tata Mobile/Xenon including necessary accessories as per OEM andassembling complete ofall as specified and directed. |
| 249 | Dismantling and taking out defective water pumpfrom Tata Mobile/Xenon and supply & Fixing new water pump with complete accessories as per existing OEM complete the re-assembling the same after testing and commissioning comlete all as specified & directed. |
| 250 | Dismantling and taking out defective water pumpfrom Eicher and supply & Fixing new water pump with complete accessories as per existing OEM complete the re-assembling the same after testing and commissioning comlete all as specified & directed. |
| 251 | Taking out old front wind shield glass and fixing new front wind shield glass with wind shield glass paste,moulding packing etc complete necessary work as requiredofgoodqualitycomplete of Tata Xenon all as specified and as directed. |
| 252 | Taking out old front bumper and fixing new bumper(complete set front side) after necessary repair work as requiredofgoodqualityandfixingthesametotheirproperplace neatly complete of Tata Xenon all as specified and as directed. |
| 253 | M&L forcalibration of FIP and governor by replacing pump elements, deliveryvalve,plugs,springs,gasketssleeves,washersfiltersetc complete all accessories as required of Tata Mobile/ Xenon/Eicher andtesting complete.Note:- The quoted rate deemed to be inclusive of manpower, Engine all accessoriesas as required ,charges for transporting engine to workshop and back after repairs & testing complete. |
| 254 | M&L forcalibration and overhauling of FIP in authrosied workshop including replacement of wornout rings plungers, damper plate ,delivery valve,pump elements , gaskit etc and reassembling testing complete for DG sets of capacity 25 to 100 KVA complete all accessories as required at site and testing complete.Note:- The quoted rate deemed to be inclusive of manpower, Engine all accessoriesas as required ,charges for transporting engine to workshop and back after repairs & testing complete. |
| 255 | All as per item ser No 69.00 above but DG set capacity 250 KVA complete all as specified and directed. |
| 256 | M&L forreplacement of stop solonoid assembly for DG set for DG sets of capacity 25 to 250 KVA complete all as specified & directed. |
| 257 | M&L forreplacement of ammeter 0 to 300 Amp range flush type 3 phase 415 volt AC with CTs Ratio 100/5A in all three phase with 4P selector switch to read current in all three phases including dismantling old ammeter of DG set Capacity 25 to 100 KVA. |
| 258 | M&L forreplacement of voltmeter 0 to 500 Volts AC including dismantling old voltmeter with 4P selector switch to read 3 phase voltage. range flush type 3 phase 415 volt AC with CTs Ratio 100/5A in all three phase with 4P selector switch to read current in all three phases including dismantling old ammeter of DG set Capacity 25 to 100 KVA. |
| 259 | M&L forGeneral servicing/repair of AMF Panel including cleaning, resetting/adjustment of relays of timer relay, over load relay, auto start/stop relay its checking and replacement if required wire, diodes resister etc complete for existing make and capacity of DG set. |
| 260 | M&L forreplacement of SMPS based electronic battery charger suitable for 12/24 volt battery charging system for existing make and capacity of DG set complete all as specified & directed. |
| 261 | M&L forreplacement of contactor 4 pole, not less then 300 Amp, 415 volt with integrated auxiliary contacts 2NO+@NC conforming to IS/IEC 60947-4-1 OR complete with existing AMF panel of existing capacity of DG set complete all as specified & directed. |
| 262 | M&L forreplacement of over and under voltage relay 3 phase 415 volts compitable with existing AMF panel of DG set complete all as specified & directed. |
| 263 | M&L forreplacement of timer switch AC/DC compitable with existing AMF panel of DG set complete all as specified & directed. |
| 264 | Supply, fixing, connecting & testing battery 12 volts,80 AH for Tata Xenon/Tata Mobile/Eicher Vehicle with lead acid terminal, indications of charging position and terminal for connection etc initial charging andtakingouttheold battery complete all as specified and directed. Make: Exide/ Amaron/ livguard. |
| 265 | Supply,fixingandconnecting & testingbattery12volts,2.5AHforHero Honda motorcycle Vehicle with leadacid terminal, indicationsof charging position andterminal for connectionetcinitialchargingandtakingouttheoldbatterycomplete all as specified anddirected. Make: Exide/ Amaron/ livguard. |
| 266 | M&Lfor repair overhauling of self starter including replacement of wornout assembly bush, spring, plungerassembly, solenoid switch, carbon bushs etc for DG set of capacity 25 to 100 KVA completeinclrectificationsofelectricwiringoftheengine complete all as specified & directed. |
| 267 | Repair/ overhauling of unsv alternator (dynmo) including replacement carbon bushes, spring commutator /slipring assemblyetc any make of DG set capacity of 25 to 100 KVA complete all as specified and directed. |
| 268 | M&L for repair/ rewinding of unsv alternator (dynmo) of Veh Tata Mobile/Xenon complete all as specified and directed. |
| 269 | M&Lfor repair to self starter and battery charger/ Dynamo by replacing damaged pinionsspringsetc.completeinclrectificationsofelectricwiringoftheengine complete Tata Mobile/Xenon. |
| 270 | Supply andfixingin replacementoftubeless tyreofsize215/75R16 or as per OEM suitableforTataXenon andtaking down old cover outer complete all as spd and directed. Make: MRF/ Apollo/ Bridgstone/JK. |
| 271 | Periodical Maint with material and servicing of the Car washing plant installed at MT yard GE NAMS for checking the serviceability of the plant, oiling,testing of the motor and belt, connecting the wires and control, replacement of belts, brass nozzles with clamp, pressure guage, water hose pipe etc complete all as directed by Engr-in-charge Note: water Hose pipe measured and Paid separetly.and balance all work rate shall be including quoted rate. |
| 272 | Periodical Maint with material and servicing of the Air compressor plant installed at MT yard GE NAMS for checking the serviceability of the plant, oiling,testing of the motor and belt, connecting the wires and control, replacement of belts, brass nozzles with clamp, pressure guage, air hose pipe etc complete all as directed by Engr-in-charge Note: Air Hose pipe measured and Paid separetly.and balance all work rate shall be including quoted rate. |
| 273 | Supply & Fixing of water Hose pipe for washing pointas per existing capacity of Pipe complete all as specified and directed. |
| 274 | Periodical Maint with material and servicing of the chain saw hexa machine (Gasoline Machine) for checking the serviceability of the Machine, oiling,testing of the carborator, plug and chain, connecting items and control, replacement of chain with new chain, Carborator and plug as per existing size complete filling T-2 Oil as per capacity provide in working condition of machine by without any extra cost complete all as directed by Engr-in-charge Note: Chain saw blade,Carborator, Plug, T-2 oil and all work rate shall be including quoted rate.. |
| 275 | Material and labour for replacement of DG Set mounted trolley for DG Set of size 2.5 x 2.0 Mtr made out of mild steel angle/ chanels medium weight beams & MS flates withj necessary welding in any postion driliing in hot/cold etc for longitude and cross members of trolly made out of ISMC chanel 100 and top of the members coverd with 6 mm thick MS plate plateformand vertical support over the plateform with MS equal angle of size 50 x 50 x 6 mm thick angles with MS flate 50 x 5 mm thick for two runs ofbracing the supports, V type towing frame with hook with spring and check nuts and mounting bracket with bush for movement of tow assembly. The assembly made out of ISMC chanel 100 with long and cross member, turning plate assembly for front wheel only fitted in front axle, the front and rear axle made out of medium weight beam ISMB 100 including tyre with tube F78-15 8 play rataing four nos with wheel drum, mounting bracket, bearings, check nuts, locknuts, key etc welded with medium beam with nut bolts washers as required for mounting the DG Set wincluding two coats of paints all as directed. |
| 276 | M & L for repairing the dent at diffrent location/ patches on surface of vehicles TATA Mobile and prepairing the base with one coat of 2k paint and after then apply one finishing coat with 2K paint by using spray machine on repaired surface to match the existing colour etc complete all as specified and directed. |
| 277 | M&L for Brake oil of suitable grade as recommended by OEM or authorised ageny for vehicles complete all as specified and directed. Make: Castrol/ Shell/ Gulf |
| 278 | M&L for GearoilofsuitablegradeasrecommendedbyOEMorauthorised ageny for vehicles complete all as speciied and directed. Make: Castrol/ Shell/ Gulf |
| 279 | M&L for Def. Urea is primarily used in diesel exhaust fluid (DEF) for Vehicle/DG Set equipped with Selective Catalytic Reduction (SCR) technology to suitablegradeasrecommendedbyOEMorauthorised ageny for vehicles/DG Set complete all as speciied and directed. Make: Castrol/ HP/Tata/ Gulf |
| 280 | M & L for replacement ofcomplete wiringwith new wiring including all connected accessories suitable for Tata Xenon/Eicher complete all as directed. |
| 281 | M & L for charging of AC gas as per OEM complete with testing & servicing of Air conditioning of Vehicle including all connected accessories suitable for Tata Xenon/Dzire complete all as directed. |
| 282 | M & L for replacement ofcomplete wiringwith new wiring including all connected accessories suitable for Motor Cycle Hero Honda complete all as directed. |
| 283 | S & F in replacement of MCCB four pole 100 Amps with breaking capacity 16KA , 415 Volts, fixed thermal & magnetic release including making all incoming/ outgoing connections fixed & MCCB matching with the existing slots complete all as specified and directed by Engineer in Charge. |
| 284 | S & F in replacement of MCCB four pole 200 Amps with breaking capacity 36 KA , 415 Volts, adjustable thermal & fixed magnetic release including making all incoming/ outgoing connections fixed & MCCB matching with the existing slots complete all as specified and directed by Engineer in Charge. |
| 285 | S&F in replacement of ON load change over switch with SS sheet metal enclosure, 415 V, 4 pole of capacity 160 Amps including connecting up incoming and outgoing cables with suitable lugs and testing complete all as specified & directed. |
| 286 | S&F in replacement of ON load change over switch with SS sheet metal enclosure, 415 V, 4 pole of capacity 200 Amps including connecting up incoming and outgoing cables with suitable lugs and testing complete all as specified & directed. |
| 287 | M & L for cleaning of installation/ substation including clearing of vegitation, wild growth and trimming of grass etc around the installation compound and removing rubbish off the premises and repair the existing iron angle if they are hanging outside to be fixed/buried in ground properly complete all as specified and as directed by Engr-in-charge. |
| 288 | M & L forwashing the completelight vehicle (PC) vehicle with foamremoving all dust particles from outside and inside using vacuum cleaner, including polishing dashboardorotherinternalparts,greasing,tightningtheloosenuts,boltsetc. complete all as directed. |
| 289 | M & L for washing the complete heavy vehicle (LCV)vehicle with foam removing all dust particles from outside and inside using vacuum cleaner, including polishing dash board or other internalparts,greasing, tightning theloose nuts, bolts etc. complete all as specified and directed. |
