|
| 1 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness)includingattachedpilasters,columns,piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: |
| 2 | 1:2:4 (1Cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 4 | Walls (anythickness)includingattachedpilasters, butteresses, plinth and string courses etc. |
| 5 | Varnishing with varnish of approved brand and manufacture: |
| 6 | Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish |
| 7 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 8 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 9 | Providingand fixingplainmultipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 10 | 6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 :2000 |
| 11 | Providing and fixing to existing door frames. |
| 12 | 24 mm thick factory made PVC door shutters made of styles cleats. The shutter frame filled and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mmhavingwallthickness1.0mmandstainlesssteel screws. The styles of the shutter reinforcedby inserting galvanised M.S. tube of size 20x20 mm and 1mm (± 0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer- in-charge. (For W.C. and bathroom door shutter). |
| 13 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 14 | Semi rigid pipe(8.1.1) 32 mm dia |
| 15 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work |
| 16 | 20 mm nominal dia Pipes |
| 17 | 25 mm nominal dia Pipes |
| 18 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 19 | 30 cm length(10.1.1) 15 mm nominal bore |
| 20 | Providing and fixing PTMT grating of approved quality and colour. |
| 21 | Circular type(11.1.1) 100 mm nominal dia |
| 22 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 23 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 24 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 25 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 26 | 15 mm nominal bore |
| 27 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. |
| 28 | Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms |
| 29 | Providing and fixing wood work in post frames and trenching for making stages dias welcome gate etc. (Materials to be taken back by the contractor by dismantling /removing the same after the function) |
| 30 | Superior Hard Wood Category II (B) |
| 31 | Providing and fixing plywood IS: 303 of different size and different thickness whever required screening all complete. (Material to be taken back by the contractor by dismantling the same). |
| 32 | 06 mm thick plywood IS: 303 |
| 33 | Providing and fixing plywood IS: 303 of different size and different thickness whever required screening all complete. (Material to be taken back by the contractor by dismantling the same). |
| 34 | 12 mm thick plywood IS: 303 |
| 35 | Providing and fixing plywood IS: 303 of different size and different thickness whever required screening all complete. (Material to be taken back by the contractor by dismantling the same). |
| 36 | 19 mm thick plywood IS: 303 |
| 37 | Providing and fixing eaves and facia board with Wood Polymer Composite (WPC) board of 18mm thick and 30 cm width of approved brand and manufacture with necessary screws etc. all complete as per the direction of Engineer - in - Charge. |
| 38 | Providing and fixing soil, waste and vent pipes with Solvent Joint. PVC (SWR) pipe Type B (Single Socket). |
| 39 | PVC (SWR) Pipe 110mm dia (Type-B) |
| 40 | Providing and fixing PVC (SWR) Fittings with Solvent Joint |
| 41 | Plain Bend 110mm |
| 42 | Providing and laying Red Carpet (Acylric syenthic) 4 mm thick and 1.5 mm width all complete as per the direction of Engineer - in - charge. (Materials to be taken back by the contractor by dismantling /removing the same after the function). |
| 43 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.(Materials to be taken Back by the contractor by dismantling/removing the same after the function). |
| 44 | Supplying of Red Carpet (Acrylic Synthetic Carpet) of 1.5 mtr width. As per direction of Engineer - in Charge. |
| 45 | Providing and laying white polyster cloth on LG dias including stiching all complete as per the direction of Engineer - in - charge. |
| 46 | Providing and fixing Flag (2mtr x 1mtr) on G.I. pipe (1 inch) excluding the cost of G.I. Pipe, Stiching Charges etc. complete. |
| 47 | Providing and fixingacrylic sheet of 6 mm thickness with necessary screw complets as per the direction of Engineer - in - charge . |
| 48 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required : (Labour Rate Only) |
| 49 | W.C. pan with ISI marked white solid plastic seat and lid (Labour Rate Only) |
| 50 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever require: (Labour Rate Only) |
| 51 | White Vitreous China Flat back wash basin size 450x300 mm with single 15mm C.P. brass pillar tap (Labour Rate Olny) |
| 52 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 53 | 250x16 mm |
| 54 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 55 | 150x10 mm |
| 56 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 57 | 125 mm |
| 58 | Providing and fixing C.P. brass two way bib cock of approved quality conforming to IS:8937. |
| 59 | 15 mm nominal bore |
| 60 | Providing and fixing toilet paper holder C.P Brass |
| 61 | Providing and fixing CP anglular stop cock with wall flange of approved quality. |
| 62 | 15 mm nominal bore |
| 63 | Providing and fixing CP finished Health Faucet with 8mm dia, 1 meter long easy flex tube in Chrome Finish & wall hook etc. complete of approved quality as per the direction of Engineer - In - Charge. |
| 64 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 65 | Bend 87.5°160 mm bend |
| 66 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (i) Single socketed pipes. |
| 67 | 160 mm diameter |
| 68 | Providing and Fixing PVC rigid Non-Decorative mica sheet 1mm thick on existing plain lining / cladding and door shutters (bathroom and WC doors) using synthetic rubber based adhesive. |
| 69 | Providing and fixing homogeneous Polyvinyl chloride sheet /tile in flooring and skirting in approved pattern on a smooth and damp proof base using rubber based adhesives of approved quality and manufacturer like Dunlop S-758, Fevicol SR 998 or equivalentincluding rolling with light wooden roller weighing about 5 kg. all complete as directed by Engineer-in-Charge, in approved colour and shade. |
| 70 | 2.0 mm thick sheet |
| 71 | Finishing walls with Acrylic Smooth exterior paint of required shade . |
| 72 | New work (Two or more coat applied @ 1.67 ILO 0 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm [(Labour Rate Only (Required Paint will be Supplied by Departmentally rest of all shall be arranged by the contractor)] |
| 73 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. [ (Labour Rate Only) (Required Paint will be supplied by departmentally rest of all shall be arranged by the contractor)] |
| 74 | Two or more coats on new work |
| 75 | Distempering with 1st quality acrylic distember (Ready made) having VOC content less than 50 grams/ litreof approved brand and manufacture to give an even shade : [ (Labour Rate Only) (Required Paint will be supplied by departmentally rest of all shall be arranged by the contractor)] |
| 76 | Old work (one or more coats) |
| 77 | Making of Temporary Pandal using G.I pipe of 40 mm dia including excavating holes more than 0.10 Cum and upto 0.50 Cum including getting out the excavated Soil and cutting, hosting, fixing in position errection as per the given drawing and applying a priming coat of approved steel primer, including welding complete. Materials to be taken back by the contractor by dismantling the same. |
| 78 | Providing and fixing in wall lining / ceiling with wooden plastic component (WPC) board , withnecessary fixing arrangement and screws etc. complete. (Materials to be taken back by the contractor by dismantling the same). |
| 79 | 12mm thick WPC board |
| 80 | Finishing walls with Acrylic Smooth exterior paint of required shade : [(Labour rate only)(Required Paint will be supplied by departmentally rest of all shall be arranged by the contractor)] |
| 81 | Old work (One or more coat applied @ 0.90 Itr/10 sqm). |
| 82 | Repair to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modifiedself curing mortar, including disposal of rubbish, all completeas per the direction of Engineer-In-Charge. |
