|
| 1 | Scarifying metalled road surface including disposal of rubbish, lead upto 50 m and consolidation of the aggregate received from scarifying with power road roller of 8 to 10 tonne capacity (DSR NO. 16.9) |
| 2 | Providing and applying tack coat with bitumen VG-10 using bitumen pressure distributor at the rate of 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. |
| 3 | Providing and laying 40 mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-39, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen precoated finegrained hard stone chipping of 13.2 mm nominal size at the rate of 0.005cum per 10 sqm and at an approximate spacing of 10 cm center to center in both directions, pressed into surface when the temperature of surfaces is not less than 1000C, protruding 1 mm to 4 mm over mastic surface, all complete as per clause 516. |
| 4 | Plain/Reinforced Cement Concrete complete as per drawing and Technical specifications. (M-15) |
| 5 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (DSR No. 10.1) |
| 6 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture (DSR No. 13.62.1) |
| 7 | Providing and inserting nipples with approved fixing compound after drilling holes for grouting as per Technical Specifications including subsequent cutting/removal and sealing of the hole as necessary of nipples after completion of grouting with Cement/Epoxy |
| 8 | Sealing of crack / porous concrete with Epoxy Grout by injection through nipples complete as per clause 2803.1. |
| 9 | Applying epoxy mortar over leached, honey combed and spalled concrete surface and exposed steel reinforcement complete as per technical specification. |
| 10 | Reflective Raised Pavement Marker Providing and fixing of raised pavement markers (Cat Eye) Type x-ASTMD-4956-04 Avery Dennision/3m(USA Make) having moulded body of polycarbonate, ASA, HIPS or ABS able to support a load of 13.635 M.T. tested in accordance with ASTMD 4280 type H and other requirement mentioned in MoRT&H Circular, its reflective lens made of micro prismatic lens (capable of providing total internal reflection of light), electronically welded to the body. The length, height and width of the body shall not exceed 130 mm, 20 mm and 105 mm respectively, The area of each reflective surface shall not be less than 13 Sq. cm . on each side sloping at the angle of 35 + 5 degree to the base to ensure maximum reflectively. it shall comply to specification of Category A of MoRT&H circular no. RW/NH 33023/10/97-DO-III dated 11.06.97 lenses shall be moulded of methyl methecrylate conforming to ASTMD 788 or equivalent. With 7 years warranty. Rate shall be inclusive of all taxes, royalty, etc. All T&P/ machine material and labour required for proper completion of work. (Ch. 27 New item -10) |
| 11 | Supplying & fixing of Linear Delineator System (LDS)panels made of Micro prismatic Retro Reflective sheeting Type XI duly laminated on thin aluminium foil to a unique corrugated shape to provide retro reflection across wide range of observations and external angles. Each LDS panel should be of nominal length of 33 inch and each ridge shall be approximately 0.34 inch high. Each LDS panel is to be firmly fixed on existing Concrite / brick work with 16 Nos Fastner/ screw as per IRC 79-2019 -Rates are inclusive of all taxes, royalty, etc. all T&P/machine material and labour required for proper completion of work. (Ch-27 new item 12) |
| 12 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35-2015 .The finished surface to be level, uniform and free from streaks and holes. Rates are inclusive of all taxes, royalty, etc. all T&P/machine material and labour required for proper completion of work. (Ch-27 new item 7) Please Enable Macros to View BoQ information |
