|
| 1 | Supply, install, testing and commissioning in replacement of of wire mesh cable tray hot dip galvanised type of size of 105 mm height X 300 mm width, 3 meter length each as per EN 12329 and IEC 61537 with wire diameter of 3.9 to 5.9 mm and having SST of 550 Hrs tested, having E30/E90 certification, with following specification all as per directed by engr in charge i) C41S/RCSN/R35 (wall/celling/ground mounting supports) every after 1 meter distance.ii) Kitaster coupler (Jointimg tray) 5 sets per joint.iii) Down rod of 1 meter length each.iv) Nuts 3 nos for each rodv) COUPFIL(Cutter) 01 No.vi) L supports for wall with all accessories such as nut bolt washers etc.Note:-a) Shifting of all existing HT and LT cables, Removing connections of these cables and refixing at its original position through cable trays in a proper manner all as directed by engr in charge is included in the quoted rates.b) All major and minor spares are required in laying of cables and fixing of cable trays which are not mention above are included in the quoted rates.c) All meterial such as cement, concerete, tiles etc to make wall/roof /ground in its original shape after fixing of cable trays are included in the quoted rates |
| 2 | Supply, install, testing and commissioning in replacement of wire mesh cable tray hot dip galvanised type of size of 105 mm height X 400 mm width, 3 meter length each as per EN 12329 and IEC 61537 with wire diameter of 3.9 to 5.9 mm and having SST of 550 Hrs tested, having E30/E90 certification, with following specification all as per directed by engr in charge i) C41S/RCSN/R35 (wall/celling/ground mounting supports) every after 1 meter distance.ii) Kitaster coupler (Jointimg tray) 5 sets per joint.iii) Down rod of 1 meter length each.iv) Nuts 3 nos for each rodv) COUPFIL(Cutter) 01 No.vi) L supports for wall with all accessories such as nut bolt washers etc.Note:-a) Shifting of all existing HT and LT cables, Removing connections of these cables and refixing at its original position through cable trays in a proper manner all as directed by engr in charge is included in the quoted rates.b) All major and minor spares are required in laying of cables and fixing of cable trays which are not mention above are included in the quoted rates.c) All meterial such as cement, concerete, tiles etc to make wall/roof /ground in its original shape after fixing of cable trays are included in the quoted rates |
| 3 | Supply ,fabricating andfixing in repairs cross arms ( any type) supports, bracing, stiffeners anti climbing spikes, LT Panel Door, hinge with welding, Chequred Plates, MS Iron Angle frame made out of MS channel, angle iron, flat of any sizeincluding drillingof holes making clamps including eye hooks, nuts bolts and washers etc welding ifrequired including painting with two coats of Synthetic Enameled paint (any shade as per site Requirement) over a coat of red oxide primer. |
| 4 | Supply and fixing PVC insulation tape red,yellow, blue colour 25 mm 25 mtr length tape Roll Lall, complete all as specified and directed by Engr-in-Charge. |
| 5 | S&F double walled corrugated (DWC) pipe of size 120 mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of LT cable in under ground/floor , complete all as specified and directed by Engr-in-Charge.Make: REX/Tirupati Plastomatics Pvt Ltd |
| 6 | S&F double walled corrugated (DWC) pipe of size 77 mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of LT cable in under ground/floor, complete all as specified and directed by Engr-in-Charge.Make: REX/Tirupati Plastomatics Pvt Ltd |
| 7 | S&F double walled corrugated (DWC) pipe of size 50 mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of LT cable in under ground/floor, complete all as specified and directed by Engr-in-Charge.Make: REX/Tirupati Plastomatics Pvt Ltd |
| 8 | M&L for in replacement of copper thimble cable (Lugs) suitable for Cable of following sizes, complete all as specified and directed by Engr-in-Charge. |
| 9 | Description all as per ser item No 8.00 here-in-before but size 70 sqmm to 95Sqmm |
| 10 | Description all as per ser item No 8.00 here-in-before but size 120 Sqmm |
| 11 | Description all as per ser item No 8.00 here-in-before but size 185 Sqmm |
| 12 | M&L for in replacement of copper cable 1 core Armoured of following sizes complete all as specified and directed. |
| 13 | Description all as per ser item No 12.00 here-in-before but size 95Sqmm |
| 14 | Description all as per ser item No 12.00 here-in-before butsize 120 Sqmm |
| 15 | Description all as per ser item No 12.00 here-in-before butsize 185 Sqmm |
| 16 | Supply, install, testing and commissioning Electromagnetic flow meter size 400 mm dia, integral display /Rubber lining with following specifecations: Flow rate-90.46 to 5427.84 cum/hr, Transmitter -die cast aluminium IP66, power supply-230V ,Outputs -RS4585/4-20mA/MODBUS, Senser Terminal housing-C.S Fabrivated IP 66,Display-Graphic Display, Flange-ASA#150 C.S., Electrode-SS16L,Grouting Electrode-SS316L,Flow tube -SS304, Coil Housing-C.S., and 1 Year warranty with Callibration Certificate inclding cutting/welding of MS pipe 400 mm dia and eletrical connection, complete all as specified and directed by Engr-in-Charge. |
| 17 | Supply and lay in replacement XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 185 sq mm 3.5 core in trenches/floor/pole/GI pipe complete including cutting/chasing to any surface and making good to the disturbed surface to match the existing, complete all as specified and directed by Engr-in-Charge. |
| 18 | M&L for Earthing complete with galvanised steel earth plate electrode 60 × 60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less\"than 1.5 metres below normal ground level, connected to galvanised earth strip 25x4 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electricalplate No. 5 connected to earthing test point all as specified or indicated including testing on completion, complete all as specified and directed by Engr-in-Charge. |
| 19 | Supply and lay in replacement MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA complete connection, complete all as specified and directed by Engr-in-Charge. |
| 20 | Supply and lay in replacement MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA complete connection, complete all as specified and directed by Engr-in-Charge. |
| 21 | Supply and lay in replacement MCCB 4 Pole, 415 V, Adjustable type, 630 Amps with breaking capacity 50 KA complete connection, complete all as specified and directed by Engr-in-Charge. |
| 22 | M&L earthing complete with Copper earth plate electrode 600mmx600mmx3.15mm thick, buried directly in ground (earth pitnot less than 2.25 metres deep below ground level) with top edge of earth plate not less than 1.5 mtrs below normal ground level connected with copper earth strip 32mmx6mm thick and copperbolts, nuts, etc and protected by GI pipe light grade 40mm bore and 20 mm dia GI tubing light grade with funnelfor watering, connecting to busbar, all as shown in electrical plate No.3 of SSR Part I incl necessary earth work and excavation in any type of soil, PCC earth chamber withRCC cover slab, salt, charcoal and MS hook, ane provn of test point complete. NOTE : copper strip 20x3mm upto 7.5 Mtrs with 40mm protection pipe shall be included in quoted rates and beyond 7.5 mtrs shall be measured and paid separately.. |
| 23 | S &F LED Tiranga Rop light 18 Mtr,IP 65,Input Power 10W/meter,Input Voltage 220-240 VAC Input frequency 50 Hzs,Input current 0.045 Amp/Mtr,Power factor 0.95,Width of strip(+/- 0.1 mm) 8 mm length/reel-18 mtrs,No of led per mtr 120 LED,LED Beam angle 120 degree ,Rope light per Colours length 6 mtr orange, 6 mtr white ,6 mtr Green,Fixing method silicone clip ,Ingrass Protection -IP -65, Ingrass protection method silicone tube ,silicone tube dimention 11.5x5.5 mm+/- 0.5 mm,working temp range-20 degree celcius to + 45 degree celcious ,working humidity range 10-90 RH, including driver for each cut piece complete all as specified and directed by Engr-in-charge.MakeWipro/Philips/Crompton. |
| 24 | Material and labour for replecement Air circuit breaker, 800 Amp rating, 4 Pole, 415 Volts, manual drawout type with microprocessor release of capacity 800 Amps, complete all as specified and directed by Engr-in-Charge. Make:Schenider/L&T/ABB/Legrand or equivalent make. |
| 25 | Material and labour for replecement Air circuit breaker, 1600 Amp rating, 4 Pole, 415 Volts, manual drawout type with microprocessor release of capacity 1000 Amps, complete all as specified and directed by Engr-in-Charge. Make:Schenider/L&T/ABB/Legrand or equivalent make. |
| 26 | Material and labour forservicing/callibration /Repair toAir circuit breaker,800 Amp by OEM OF ACB only forEDO ( Electrically Draw out type/MDO type ( Mannually Draw out type).Taking out ACB for servicing/repair and checking/callibration of microprosser release ,Earth fault protection of 4 pole,50 KA breakingt capacity 415 volts with all draw out type mechanism,advanced self powered electronic protection units,neutral overload protection.automatic earth fault relay/over current relay,automatic safety shutter,inbuild temperature protection.icu=ics=icw(1s)=50 Ka fixed in panel including shunt release,earth fault release, wiring checking,LT UGcable connection requirement of any spare parts for its healthy functioning of ACB complete all as specified and directed by Engr-in-Charge Note- Certificate of Servicing /callibration will be providded by the contractor free of cost |
| 27 | Construction of valve pit brick masonary, internal size 1200x1200x1200mm (from top fo PCC to bottom of cover) including excavation in any type of soil, returning, filling in around foundation, removal of surplus soil to a distance not exceeding 50m, PCC 1:4:8 type D-2 in foundation, brick work in CM 1:4, 12mm thick plaster in CM 1:4 to internal surfaces and flush pointed externally as the work proceeds in the same mortar PCC coping 1:2:4 type B-0 using 12.5mm graded stone aggregate, pit cover of MS sheet 5mm thick, handle and 40x 6mm FI 230mm long with 25mm dia hole at other endlocking arrangement, fixing arrangement and painting with synthetic enamel paint two coat of red oxide primer, complete all as specified and directed including demolition of old UNSV existing valvepit. |
| 28 | Supplying and laying synthetic Rubber insulated mats 2.5 mm thick for voltage upto 11 kv for electrical purpose suitable for electrical shock safety of sizes 2m x 1m, complete all as specified and directed by Engr-in-Charge. |
| 29 | Supply & fix in replacement Loss of Head (LoH) for Rapid sand filter cap 40,000 Glns/hours, monitoring the Level in High Pressure and low pressure side of the gravity filter / Traveling water screen. The Loss of Head arrangement shall have following feature complete all as specified and directed by Engineer-in-Charge.-(a) Measuring Differential level in Filter Beds.(b) Housing : Cast Aluminium, Powder Coated. 198*170* 99 mm(c) Mounting : Wall Mounting(d) Power Supply : 230 V AC, 50 Hz(e) Power Consumption : 4 VA (approximately)(f) Adjustment Range : Span : Min 10% of Electrode Length, Max 80% of Electrode Length &Zero : Max 80% of Electrode Length(g) Alarm : A relay C/O rated 6 Amps 230 V, non-inductive load adjustable throughout range(h) Current output : 4-20mA DC non isolated, max. load resistance 600 Ohms, corresponding to differential level(j) Accuracy : ±4% of Electrode Length(h) Supplied with Rate of Flow (RoF) in a common CA Housing with IP-55 ProtectionNote: Material and labour charges & cables for installation/connection of setup & taking down old setup shall be deemed included in the quoted rates. |
| 30 | M&L for painting complete outer surrounding of Over head tank in Tiranga Colour including writing of \"SAVE WATER, SAVE LIFE \" in blue colour on center white colour, complete all as specified and directed by Engr-in-Charge. |
| 31 | M&L forflex banner of size 1.0 mtr x 0.6 mtr supported with iron frame, about the machinery installed in different instalations such as Cap, discharge, MES No, Year of installation and head of the machineryon the blue background with white colour including fixing on wall with clamps, complete all as specified and directed by Engr-in-Charge. |
| 32 | M & L for painting of Header of dia up to 300mm with inlet, outlet, sluice valve, NRV etc including surface preparation by scrappingwith emery paper and paintingwith one coat of red oxide primer and two coats of synthetic enamel paint of existing colour of approved make to the satisfaction of Engr in Charge complete all as specified and directed by Engr-in-charge.Note: Marking with white colour on each outlet is included. |
| 33 | S&F 3D signage board made of high quality plastic material with raised 3S letters supported with iron frame of size 4 mtr x 0.5 mtrs in Acrylic sheet moulded letters (TAWI JACKELL Garrison Engineer (Utility)including MES logo printedon both side of name on the blue background with white colour of size 1x1 feet white in colour with good quality LED Strip including constant current electronic driver and making connection with suitable size copper conductor multistranded FRLSH wire including fixing on wall with clamps, complete all as specified and directed by Engr-in-Charge.Make of LED strip :-Philips,Wipro,Havells or equivalent |
| 34 | M&L for replacement of Slow speed agitator (Alum mixer) Liquid Handled: Alum, Shaft length 850mm below mounting plate, Shaft Dia. 25 mm, Impeller Dia. 250mm PBT Type - Three Blade , Impeller - 2 Nos., Output RPM 150 RPM, Gear box details: Worm Type, Output RPM 150, Ratio 10:1, 1HP /0.75 kw, 4pole, motor , SF- 2, Model- ELMN50/63-. Service tank of capacity 500 ltrs. Motor Data : Drive Rating HP / KW 1Hp / 0.75 Kw, Drive Details 4pole, 1440 RPM, STD. TEFC, Flange mounted, Vertical, IP55, 50hz, 415volts, 3 Phase, IE2, Non Flame proof.Make Crompton Greaves, Kirloskar, KSB.MOC of Shaft SS316, MOC of Impeller SS316,Mounting Bearing Housing M.S. Painted, including 500 Ltrs. Tank complete all as specified and directed by Engr-in-charge. Make: Dynamic Equipments Pvt. Ltd, Verito Engineering Pvt Ltd, RECKON Techno Dosing Pumps And Systems, Rudraksha Engineering or equivalent as approved by accepting officer. |
| 35 | Supply, fabricate, erect , connect, test and commissoning of factory made, CPRI approved, cubical type, indoor type LT panal board of size 1500x1200x600 mm,totally enclosed , dust, weather and vermin proof 1100 Volt grade , 50Hz, AC supply made out by 3.15mm thick CRCA sheet steel for load bearing and 2 mm thick for non load bearing, fully compartmentalised, with IP 65 protection all as per conferming to IS 2417 of 1962 complete including the following accessories housed , complete all as specified and directed by Engr-in-Charge.(a) MCCB 4 Pole 250 Amps, 415 V, 35 ka ( Incomer). (b) Indicator (RYB) I set. (c) MCCB 4 pole 125 Amp, 35 ka -02 ( Out going)(d) Bus bar 400 Amp with CT&PT.(e) MCCB 4 pole 63 amp, 35 Ka -02 (f) Volt meter & Amp meter for suitable capacity of panel |
